Search Documents

By J. J. leR. Cilliers

ABSTRACT The recently introduced concept of negative taxation complicates estimation of the distributable profit of certain South African gold mines, and an assisted mine could operate at a working loss and yet produce an overall profit for distribution amongst its shareholders. A simple diagram is presented from which the approximate working profit or loss, taxation payable or tax credit received, and the distributable profit of an assisted mine can be estimated directly for any combination of the four main variable operational factors: tonnage milled, recovery grade, unit cost and capital expenditure. INTRODUCTION The effects on the working profits of South African Gold mines caused by changes in unit working costs, recovery grade, tonnage milled and capital expenditure are readily estimated. For normal tax- and lease-paying mines the distributable profit is related to the working profit and the latter is a commonly accepted comparative measure of the profitability of an operation. However, the recently introduced concept of State assistance in the form of negative taxation1, i.e. a tax credit, for mines with a life of less than eight years complicates such estimates. A requirement of State assistance is that an assisted mine must lower its normal pay limit by 16 to 20 per cent, and it will be possible for a mine to operate at a working loss and yet produce an overall profit for distribution amongst its shareholders. In the case of an assisted mine it is therefore necessary for management to judge the effects of changes in unit costs, grade, etc., in terms of distributable profit instead of working profit. This will require repeated calculation of tax to be paid or tax credits that will be received under the numerous possible combinations of the four main variable factors. However, with the aid of the diagram illustrated in Fig. 1, it is possible to assess at a glance the practical effect of these variables on the distributable profit of an operation not subject to tax on the normal formula, or small mine formula, with sufficient accuracy to decide whether a detailed analysis is required. USE OF THE DIAGRAM From the central point 'X' in Fig. 1, a range of tonnages milled per annum has been plotted along the north-bearing axis, a series of costs per ton milled in the northwestern quadrant, recovery grades in the northeastern quadrant, and capital expenditures in the southwestern quadrant. Starting from the tonnage milled per annum, a line is drawn east and west across the two northern quadrants up to the points where it reaches the desired cost- and grade-lines. From these points two north-south lines are drawn into the southern quadrants. A further line is drawn to the east from the point where the western north-south line crosses the desired capital expenditure. Distributable profit is read off in the southeastern quadrant where this line intersects the eastern north-south line. Every possible combination of

By P. Stevenson

Correlations for the critical velocity needed to hydraulically convey particles in horizontal, or near-horizontal, pipes are either explicitly dependent upon the shear stress imparted by the fluid upon the surface of the particle bed, or require a velocity and hydraulic diameter. Often such approaches are modified to account for pipe inclination by the introduction of simple factors. However, we assert that the physics that underpins the hydraulic conveying of particles in steep pipes (such as a directionally drilled oil well) is dissimilar to that which governs particle behaviour in horizontal pipes. In steeply inclined systems, a sliding sediment induces an upward counter flow and hence an autogenous contribution to the shear rate. The physics underpinning particle hydraulic conveying in steep systems is explored using the separation results of Laskovski et al.10

Jan 1, 2007

"Chairman: Mr W. S. GALLAGHERRapporteur: Professor A. M. STARFIELDPapers:Long-term mine production scheduling by G. C. S. BurneAn application of linear programming to investment analysis by A. ErlandssonOptimizing medium-term operational plans for a group of copper mines by M. Splaine, D. C. Atkinson, W. Davison and L. SmithThe simulation of underground stoping and transport operations in gold mining by F. H. Touwen and N. C. JoughinProduction planning is a subject that lies at the interface between the computing centre and mine management. Discus¬sion during this session was thus largely concerned, directly or indirectly, with communication between computing and mining personnel, and as such was relevant to the symposium as a whole.Mr A. Weiss set the tone of this discussion by referring to `user-orientated systems'. He congratulated Mr Burne in this regard, pointing out that his long-term production scheduling program, as a computer system, was similar in approach to the manual system it replaced, and was therefore easily understood by planning engineers. He asked whether the schedule engineer had his 'hands on' the system, to which Mr Burne replied that the engineer did in fact spend several days running alternative schemes through the computer. Mr Weiss commented on the advantage of having terminals on site for this sort of engineer-computer interaction. He also commented on the flexibility of Mr Burne's approach to scheduling and how preferable this was to a one-step optimization package. This was brought home by a question from Mr H. D. Small: Mr Burne's program sometimes found it necessary to temporarily halt an advancing face, and he asked whether the logic of the program could be altered to avoid this (e.g. by suitably slowing down the rate of face advance). Mr Burne replied that it was in fact easier for the planning engineer to sort this problem out manually. The way in which the computer results were presented made it particularly simple for the production engineer to see how to avoid or remedy a stopped face.On the technical side, both Mr Weiss and Mr H. M. Wells questioned Mr Burne on the handling of grade control by his program. From answers by Mr Burne and his colleague Mr K. H. Thomson it emerged that a spot-check on grade every now and then was all that was necessary at Mufulira, and that the idea of actual grade control was more a question of short-term than of long-term planning."

Jan 1, 2014

By M. M. Oosterveld

"In South West Africa diamonds are mined from ancient beach deposits by the Consolidated Diamond Mines of South West Africa, Limited.To improve the control of mining production, a computer is used for the calculation of statistically more accurate and homogeneous ore blocks. Geological and sampling information has been digitized and stored on magnetic files.The figures derived for each block entail the calculation of the diamond size frequency distribution, the diamond density distribution and the ore reserve by using the density distribution.The diamond size frequency distribution is used for estimating the revenue in an ore block.A description is given of how a linear programming system can be used for production planning."

Jan 1, 2014

By R. P. King

A class of gravity separation unit operations in ore-dressing relies for its operation on the production of a stratified bed. Heavier material gravitates downwards, and separation is achieved by splitting the ore horizontally, with the recovery of a dense stream and a lighter stream. The important ore-dressing unit operations that fall in this class are the jig, the Reichert cone and the pinched sluice. A new quantitative model based on Mayer's potential theory is developed here. This model is developed completely for the simple case of binary mono-size particulate materials, but the extension to units operating with feed material distributed over particle size and density is discussed in principle. The model can be used to predict the performance of these units and is very suitable for simulation. The model is tested successfully against experimental data obtained from a batch jig and a Reichert cone.

Jan 1, 1987

1. Mintek reports The folowing reports are available from Mintek, Private Bag X3015, Randburg, 2125 South Africa. They are available at R25 (plus R3,25 GST) per copy to South African addressees, and US$25 per copy (including airmail postage) to addressees elsewhere. Report M91D A mineralogical investigation of samples from the Renosterkop tin prospect near Upington, by M.J. Southwood. First issued Jul. 1983, reissued May 1989. 16 pp. Report M256D The upgrading of Mamatwan manganese ores heavy-medium separation, by P. W. Overbeek. First issued Apr. 1986, reissued May 1989. Report M299D A mineralogical investigation of samples from the Eenzaamheid cobalt-molybdenum deposit, by C.D. de Nooy. First issued Jan. 1987; reissued May 1989. Report M301D The evaluation of manganese metal powder by automatic image analysis, by E.J. Oosthuyzen. First issued Feb. 1987, reissued May 1989. 13 pp. Report M311D Mineralogical and beneficiation studies of ore from Lutzputz, by R.N. Guest and C.T. Logan. First issued Mar. 1987, reissued May 1989. 13 pp. Report M314D The beneficiation of a sample of magnesium ca/crete, by L. Jonker. First issued Apr. 1987, reissued May 1989. 13pp. Report M369 The determination, by flow-injection analysis, of thiocyanate, by E.A. Jones and M-J. Hennings. Jun. 1989. 7pp. Report M389 A spectrophotometric method for the determination of zinc by flow-injection analysis, by D.E. Barnes and RA. Jones. Jul. 1989. 15 pp.2. Recent publications Pumps-principles and practice. Available from K. Myles & Associates CC, P .0. Box 2212, Northclif 2115. :200pp. R99 including GST. Standard handbook of hazardous waste treatment and disposal, edited by H.M. Freeman. Bergano Book Co., P .0. Box 190, Fairfield, CT 06430, USA. 1120 pp. US$130.Quality control handbook, by J. Juran and F. Gryna Jr. Bergano Book Co. (address as above). 4th 00. 1536pp. US$125.Refractories in the manufacture and transport of pig iron. Verlag Schmid GMBH, P.O. Box 6609, 7800 Freiburg, West Germany. DM 100. The user-computer interface in process control, byW.E. Gilmore, D.I. Gertman, and H.S. Blackman. London, Harcourt Brace Jovanovich Ltd, 1989. " 312pp. $29.Aluminum alloys-contemporary research and applications, edited by A.K. Vasudevan and R.D. Doherty. London, Harcourt Brace Jovanovich Ltd, 1989. " 676 pp. " £90.3. TMS publications issued recently The folowing publications are available from The Minerals, Metals & Materials Society, 420 Commonwealth Drive, Warendale, PA 15086, USA (Telephone: (412) 776-9000, Telex: 9103809397, Fax: 4127763770). Advances in magnesium alloys and composites, by H. Paris and W.H. Hunt (eds.). 145 pp. $65. Arsenic metallurgy-fundamentals and applications, by R. Reddy (ed.). 515 pp. $104. Casting of near net shape products, by Y. Sahai (ed.). 7oopp. $155.Continuous casting of non-ferous metals and alloys, by H.D. Merchant, D.E. Tyler, and E.H. Chia (eds.). 360 pp. $90.Dislocations and interfaces in semiconductors, by K. Rajan, D. Ast, and J. Narayan (eds.). 210pp. $75.

Jan 1, 1989

By S. M. Rupprecht

A deposit to be mined by underground methods can be accessed by a number of methods: ? Adit ? Decline or ramp ? Inclined shaft ? Vertical shaft. Adits are an economical approach when the orebody is above the general floor elevation i.e. suitable in hilly or mountainous terrain. Incline shafts are limited to relatively shallow deposits, and because they are developed on an incline, development lengths for a given depth are the three to five times longer than for a vertical shaft. Vertical shafts are the preferred method for deposits deeper than 300 m but the development rate is slow and construction costs are very high. Declines or ramps offer early access to shallow deposits, which develops the ore body expediently, but are generally developed at a gradient of approximately 12 per cent. Decline haulages have become an attractive alternative to shaft hoisting, and over recent years the role of decline access has become more widespread throughout South Africa. Traditionally, South Africa has enjoyed the use of shaft systems, largely due to the large knowledge base of mining the Witwatersrand Basin, where vertical and inclined shafts were the norm. South Africa has also had the advantage of cheap electricity, giving shafts a definite economic advantage. However, in recent years the national power utility ESKOM has undergone an expansion programme that has led to tariff increases of nearly 100% over a three-year period. Based on the changes in electricity tariffs and technological improvements to underground haulage trucks, the economic inputs to access development have changed. This paper reviews mine access for shallow deposits as currently applied in South Africa. Based on current economic inputs, the paper investigates at what point a vertical shaft would be more economical than a decline system utilizing typical South African mining equipment.

Jan 1, 2012

By B. P. Watson, T. J. Maphosa, D. P. Roberts, L. J. Gardner

The results of FLAC3D modelling on chromitite Upper Group 2 Reef pillars from the Bushveld Complex of South Africa are described. The model input parameters were determined from laboratory triaxial tests with post-failure measurements. These geomechanical tests were performed on rock materials within the pillars and the immediate pillar foundations. In the models, postfailure behaviour was simulated using the concept of cohesion softening. Models were built to determine the strength and behaviour of pillars with a width-to-height ratio of approximately two. The original research aimed to find a suitable depth below the surface where Impala Platinum Ltd could safely introduce crush pillars; however, the paper only describes the model results: the ideal depth of the crush pillar introduction is not discussed. The results of the modelling are compared with the PlatMine formula for peak pillar strength and with an underground instrumented pillar located elsewhere on the same reef. Some insight into the effects of grid size on strength is also provided. Further underground measurements are recommended to verify the model results

Sep 9, 2024

By J. W. van der Merwe

Technology is advancing at a rate that makes it extremely difficult for the mining Industry to keep pace. Many advances occur within a given piece of technology and often this is missed by the disciplines that could have gained advantage by its implementation. Often this may have been simply an aspect of cost exceeding benefit. However, there are some technologies that potentially have such a far-reaching impact on the mining industry that the benefits simply outweigh the cost. The application of 3D laser scanning in the mining industry has the potential of taking the concept of ?Google maps?? underground. This presents an opportunity where the virtual world of underground can be traversed with relative ease and many aspects of measurements could be obtained without having to visit the working place again, potentially saving countless man-hours and still delivering precision work with significant savings in downtime, stoppages, and exposure to safety incidents. Anglo American Platinum maintains its competitive advantage though the review and application of appropriate technology. This paper describes the 3D laser scanning trial at one of Anglo American Platinum?s new shafts, and goes on to show the benefits encountered through the application and the involvement of the various MRM disciplines.

Jan 1, 2012

By C. Banff, E. C. F. Hamman, J. Venter

Open pit slope stability analyses for large scale instabilities are often carried out using limit equilibrium, finite element or finite difference computer programs. All of these require empirical estimates of rock mass shear strength when calibrated values are not available, which is a common occurrence. A common method of estimating rock mass shear strength is the Hoek-Brown failure criterion, which often over- or underestimates rock mass shear strength when used in limit equilibrium or elastic linearly plastic slope stability analyses, resulting in published alternative estimates for the coefficients of the Hoek-Brown failure criterion. This paper investigates the differences between limit equilibrium and elastic linearly plastic slope stability analysis based on the Hoek-Brown failure criterion. The investigation consisted of a comparison of 3840 RS2 finite element analysis models completed with strain softening, and 216 Slide2 limit equilibrium models. The models were used to evaluate a methodology to determine equivalent limit equilibrium and elastic linearly plastic shear strength parameters that provide the same stable slope angles and instability back break distances as the more representative strain softening stress analysis methods. This paper presents the methodology and compiles the results into design charts and equations for equivalent limit equilibrium Mohr-Coulomb shear strength parameters, that simplify calibration against actual case studies. The results compare well with older empirical shear strength estimates, however, a detailed calibration of the results against case studies will need to be carried out. The analysis also did not consider pore pressure effects; this is left for future publication.

Sep 1, 2025

By N. V. Moraka

Mining companies are required by law to improve representation of women on their boards. However, progress in this regard has been slow. Boards of directors play an important role in formulating corporate strategy, risk assessment, and effective governance for sustained financial performance. Although some women have successfully maintained board seats, others have been unable to do so. It is difficult to ascertain whether women are being appointed as tokens to satisfy social pressures, as little is known about the experiences of women board members in mining, which may inform or refute tokenism. In-depth interviews were conducted with 20 women and 16 men across six listed mining companies. Thematic data analysis revealed evidence of tokenism where recruitment to mining boards is compliance-based and is informally driven by influential directors. Adverse boardroom experiences that further confirmed tokenism were reported by women, such as disregarding their contributions, condescending behaviour, and limited influence in decision-making, while other women sought to validate their competence and oppose social exclusion. This study recommends that a strong Board Chair and nominations committee is critical to ensure sustainable recruitment of competent and suitably qualified women; and further foster a culture of inclusivity and valuing gender-diverse boards.

Dec 13, 2023

By M. Z. Emad, S. Raza, K. Jalil, M. A. Raza, M. U. Khan, S. A. Saki

Dimension stone mining is Increasing because of growing demand from the building and construction industries. Diamond wire saw cutting is a popular dimension stone mining technique around the world. Estimation of the production cost for this method is critical for these operations. n this research a production cost model was developed for the mining of granite using a diamond wire saw. Cost and production data were collected from a granitic dolerite operation in Pakistan for a 4.5-year period, and analysed to identify the cost components. Fuel (34%), labour (15%), consumables (40%), and maintenance (5%) were found to be the four major cost components in this operation. A regression-based dimension stone production cost model incorporating statistically significant variables was developed. The data presented a strong correlation of production cost with fuel, labour, and consumables costs. Finally, a production cost model based on the consumption cost of diamond wire is presented. The model was verified using actual production cost data, which indicated 95% (R2 = 0.95) variance in the data between the predicted and actual production cost values. The model may help field engineers in computing their dimension stone operational cost during the cutting phase.

Nov 6, 2023

By L. A. Vermeulen

A simple argument shows that it is impossible for the flight of a rod in contact with a litter bar in a rotary mill to be initiated at that point on the upside of mill rotation when all the forces acting on the rod are in equilibrium. The argument was confirmed experimentally in a study showing that the lift of litter bars is a function of their height, that the rod velocity at the point of departure has a significant radial component, and that the subsequent flight of a rod is along a parabolic trajectory as predicted by elementary mechanics. A quantitative account of the observed effects, which is based on a dynamic theory of the sliding interaction between rods and litter bars, revealed interesting properties of the motions of rods down the surfaces of litter bars when the latter are in uniform circular motion during the rotation of a mill.

Jan 1, 1985

By A. R. Javadi

Pyrite (FeS2), chalcopyrite (CuFeS2), sphalerite (ZnS) and galena (PbS) generate hydrogen peroxide (H2O2) when placed in water, with pyrite generating the most amount of H2O2. The order of these minerals for generating H2O2 in water is: pyrite > chalcopyrite > sphalerite > galena. In previous research, the methods of generation of H2O2 in the grinding mill were studied. In this study, data from experiments were included by using MODDE 9 software for six parameters composed of water, grinding media, particle size; adding collector to the grinding, and adding depressant and pH. Finally the optimal condition was achieved. According to the results, most of the recovery is related to the particle 75 μ size and when using processed water, adding 100% collector and without depressant and pH 10. The most recovery of lead in the case of the use of fresh water is in the case of 100% collector, without depressant, pH 10 and 150 μ particle size. Maximum recovery in fraction size 45 μ in the case of water process is 100% collector, without depressant and pH 10. Maximum depressant of pyrite will be the fraction size 75 μ, distilled water, without collector, 100 depressant. Keywords: Sulfide mineral, hydrogen peroxide, flotation, oxidation

Jan 1, 2020

By J. Nell

Heavy mineral deposits often contain relatively high levels of radioactive elements (thorium and uranium in particular).It is difficult to obtain clean separation of ilmenite and monazite (the main impurity mineral containing radioactive elements), and physical intergrowths of the two minerals are, in fact, not uncommon. As a result, ilmenite concentrates obtained from such deposits often contain high levels of thorium and uranium. Because of the large negative free energies of formation of ThO2and U3O8boththorium and uranium report to the slag during smelting and if an ilmenite concentrate contaminated with monazite is used to make high titania slag, the concentrations of these elements in the slag end up about 40% higher than in the ilmenite feed. Previous work, patented by RGC Mineral Sands Limited, and subsequently confirmed by Mintek, showed that radioactivity may be reduced by roasting an ilmenite concentrate with borax at 1000°C to 1100°C and leaching it with hydrochloric acid1. It is evident that the cost of an ilmenite roast/leach process will be high and there may be economic benefits in removing the radioactive elements from the slag instead (the volume of slag to be treated is smaller than the volume of ilmenite feed). To remove radioactive elements from the slag it is necessary to know how these elements occur in the slag. Inother words, the distribution of uranium and thorium between the various oxide, silicate and metallic phases in high titania slag must be determined. Once the deportment of thorium and uranium between the various phases ha sbeen determined, an appropriate process for slag purification can be developed. Test samples High-titania slag was prepared in a pilot-scale DC furnace from ilmenite concentrates with different levels of uranium and thorium. Subsequently, ten slag samples representing a range of compositions were selected for bulk chemical analysis, scanning electron microscopy and micro-analysis. The samples were crushed to a maximum particle size of 1 mm and from each sample a 20-kg batch was riffled out for analysis. Bulk chemical composition Chemical compositions of the samples selected for test work are given in Table I. TiO2, Al2O3, SiO2, MgO, MnO, FeO and V2O5were analysed by ICP-OES, Na2O, CaO andCr2O3by atomic absorption spectroscopy and U and Th by XRF (the XRF detection limit for U and Th was around 4 ppm). The ?B? series has a higher silica content than the others as a result of small silica additions that were made during smelting. All samples have elevated alumina levels as a result of furnace refractory contamination during smelting. As expected, there is an inverse relationship between the concentrations of TiO2and FeO in the samples (Figure 1).The TiO2and FeO levels are similar to the levels found in industrial slags2. Extreme conditions of reduction under which reduction of more ?refractory? oxides (e.g., chromia, magnesia, silica, alumina and even urania and thoria) might take place were not explored in the study. Note that BB1and BBB1 contain more than 7% combined silica and alumina (SiO2as a flux addition during smelting, and Al2O3from refractory contamination) and they do not fall on the general trend defined by the other samples. The U and Th concentrations of sample E2 is noteworthy. In the preparation of slag E2, monazite concentrate was added to the ilmenite to increase the concentrations of radioactive elements in the slag. This was done primarily to facilitate the detection of Th and U during the phase chemical characterization of the slag. Radioactivity measurements Gamma ray emissions from the samples were measured [ ]

Jan 1, 2007

By K. Arnold

AngloGold Ashanti has been proactive in the field of energy management for many years. AngloGold Ashanti is a signatory to South Africa?s National Energy Accord of 2005 calling for a15% reduction in energy consumption by 2015 for the mining sector. This target also supported our internal targets that were already set. AngloGold Ashanti?s seven South African mines consume on average 440 MW. Due to the dynamics of gold mines, and the large numbers of relatively small energy efficiency initiatives and awareness campaigns made measurement and verification of energy efficiency very difficult at a macro level since some initiatives could get lost in the fluctuating load profile. This paper will discuss the methodology and process followed to quantify the impacts of the combined energy efficiency initiatives at macro level. It will quantify the energy efficiency impacts in megawatt-hours (MWh), financial, and equivalent carbon emissions (CO2e) reduction with reference to our baseline year, 2004, for the Vaal River and West Wits mine clusters.

Jan 1, 2009

By M. H. Lampen

The SILAG Material Tracking System MTS monitors and controls the complete material flow throughout the plant - and even companywide. The customized system developed by Siemens especially for bulk material handling applications enables companies to track bulk material from the mine to the harbor, to the steel mill or to the power plant. All relevant material data is available at every single step of the material’s journey. SILAG is an open, scalable system based on Windows NT / 2000. Using standard interfaces of Windows NT, like API, ODBC, SQL and socket technology, the system is very flexible and can easily be tailored to meet different requirements. SILAG can be used as a stand-alone solution or - if complete plant control and visualization is required - as a component of a fully integrated automation system with the Win CC HMI system and the PCS7 process control. In contrast to conventional material tracking systems, SILAG offers many advantages. - The Material Tracking System is an object oriented, online to the process, linked system. All changes in the plant during operation e.g. selecting another conveyor route, start and stop etc. will be automatically detected and will influence the calculation. - The systems is able to split and blend material (quantity and quality).Measurements of tonnage, volume or quality analysis can be linked online to the system. Each movement of material is monitored by the system and leads to online recalculations of the images and databases. - All material data is based on 3D-stockpile images, which are calculated by an internal mathematical model based on quantity and quality information. - If a laser scanner is available on a stockyard machine it can be taken to update the profile directly from the piles. - Efficient control and report functions are available on each, free selectable point of the total plant.

Sep 1, 2001

By and Z. S. Abisheva, Z. B. Karshigina, Ye. G. Bochevskay, A. S. Sharipova

The production of precipitated silica in the United States is about 145,000 tons of SiO2 and its prices vary significantly (from $ 1 to $ 4.5 per kg) depending on the area of its application. One of the most important parameters is its specific surface characterising dispersion (particle size and shape, presence or absence of pores), at a certain value of which the material acquires new properties and quality. At present, a technology has been developed for processing slag from phosphorus production to produce precipitated silica (‘white soot’) with a high specific surface and the possibility of extracting valuable components such as rare-earth metals (REMs) into a product enriched with them has been shown. However, the content of impurities in the deposited silicon dioxide, such as aluminum and iron, is above acceptable limits and may affect the quality of the final products. Therefore, along with the structure and specific surface, a very important characteristic of ‘white soot’ is the chemical purity of the material. In turn, calcium oxide occupies a significant share in the concentrate of rare-earth metals, which affects the content of ΣREMs oxides, which does not exceed 17.3 %. The low content of a valuable component may affect the feasibility of further processing. For the most complete utilisation of phosphorus slag, the authors propose a method for their acid processing, which allows for minimising the conversion of impurities to finely divided silica and collective concentrate, which will improve the quality of these products. Keywords: Phosphorus slag, precipitated silicon dioxide, rare earth metals, leaching, white soot, specific surface, technology

Jan 1, 2020

By G. Akdogan, S. M. Bradshaw, M. I. Isaacs, P. Van Wyk

In the mineral processing industry, Ni-Cu-Fe-S converter matte is leached in order to remove base metals from a concentrate containing platinum group metals (PGMs). This paper investigates the atmospheric leaching process, in order to develop a better understanding of the leaching behaviour of the base metals; in particular Cu, Fe, Ni, and the PGMs in particular Ru and Ir with key process variables, acid concentration, copper concentration under oxidative leaching conditions. Higher initial acid concentration resulted in a higher copper, iron and nickel extractions, as well as higher leaching rates together with faster Cu, Ru, Ir precipitation occurring. On the other hand, a higher initial copper concentration resulted in more nickel but less iron being extracted. Keywords: PGM, converter matte, leaching, precipitation

Jan 1, 2020

By Karl-Heinz Obst, Juergen Stradtman

The importance of the chemical and physical properties of lime has been overlooked for years although the quality of lime plays an important role in the production of steel. With the introduction of the oxygen injection process these properties have been re-evaluated. The CaO, MgO, S, and P2O5 contents of lime are important, but so are the physical properties such as granulation, reactivity with respect to slag formation, and the degree of burning. Soft burnt lime enhances de-phosphorisation and de-sulphurisation, and facilitates the smelting process in general, mainly due to its large specific surface. Special lime, prepared as briquettes from quicklime and fluxes or as pellets from limestone and various fluxes with or without binding agents, clearly accelerates lime dissolution during the slag formation process, lowers the melting point, and enhances de-phosphorisation, de-sulphurisatlon, and de-carburisation even more than soft burnt lime. The introduction of special limes in the oxygen injection process for steel production has opened up new fields for commercial exploitation of slags as well as improved operational techniques.