Search Documents

By J. Gunaselvam

This article deals with an investigation into the specification and use of appropriate seating systems to reduce whole-body vibration (WBV) exposure in typical vehicles used in the SA mining industry. The EU Directive EU/44/2002 to be legislated in 2005 in European countries, provides legal and economic motivation for this project. The criteria for seat selection can be condensed to the requirements in the directive, which mandates an action level of 0.5 m/s2and a vibration exposure limit of 1.15 m/s2 for an equivalent 8-hour daily exposure period. As part of this study six suspension seats, which the manufacturers claim satisfy the requirements in ISO 70966, were tested to determine the most suitable seat for an articulated dump truck. Six test subjects, three ?light? and three ?heavy? as specified in ISO 70966, were used to estimate the seat transmissibility functions in the vertical direction of the six different suspension seats. Transmissibility functions were measured in the laboratory with two excitation levels of 1 m/s2 and 2 m/s2 r.m.s. in the 0.5?30 Hz frequency range, as well as one spectrum approximating the EM5 spectral class. SEAT values were calculated for road vibration data measured on a typical articulated dump truck. A set of seat selection guidelines that can be followed by vehicle manufacturers and suppliers, procurement officers and and the technical staff on a mine is proposed in this article. It is recommended that additional studies of the use and operating conditions of seating systems in the SA industry, as well as an epidemiological survey be commissioned to gather additional information on this subject. Nomenclature ADT Articulated dump truck DSTF Dynamic seat testing facility EM1 Frequency spectra associated with earth moving equipment (?articulated or rigid frame dumper?) according to ISO 7096 EU European Union ISO International Standards Organisation PSD Power spectral density r.m.s .Root mean square SEAT Seat effective amplitude transmissibility WBV Whole-body vibration

Jan 1, 2005

By B. J. Vorster

AngloGold South Africa region currently consists of twelve gold plants. These plants use a combined total of $20 million of cyanide per annum. Of this, the major portion (60%) is consumed at two Ergo dump retreatment plants. Historically the primary motivation for cyanide control at Ergo has been one of leach/cost optimization. However, more recently, with the increased public awareness of cyanide in the environment, a secondary but increasingly important motivation for control has been to ensure that only the minimum amount of cyanide is added to the process whilst not compromising leach performance. Following a brief overview of the Ergo process, the methodology in determining the amount of cyanide to be added is described. The paper then traces the developments in cyanide control from very basic manual systems to the current automated control system. In line with the increasingly sophisticated control systems, developments also took place in regards to the method of cyanide analysis. The development of these analysers is also discussed. Whilst cyanide is one of the major drivers, if not the major driver of gold dissolution, it cannot be viewed in isolation particularly with respect to the relationship between cyanide and oxygen as ascertained from the Elsner?s well-known equation. Consequently, in order to control cyanide addition, knowledge of the relative cyanide/oxygen profiles is necessary. Various means investigated at Ergo for pulp oxygenation have therefore been included for the sake of completeness. Finally a comparison is made of the control achieved from the current system compared to the original manual system. The knowledge and experience gained at Ergo is now being used to draw up guidelines for the installation and optimization work at the other AngloGold plants. The net effect of this will be reduced cyanide consumption for the region, which also, apart from the obvious economic benefit, translates into a reduced environ-mental risk.

Jan 1, 2001

By J. Botin

Traditional risk quantification methods provide little information on the sources of risk, and tend to produce static over-conservative evaluations, which do not account for changes in the performance of the project. Capital investment decisions for large mining projects require more complex risk evaluation models that include the value of flexibility and the different risk levels associated with uncertainty on project variables (price, grade, dilution, and production rates, among many other). In this context, real option valuation (ROV) methods have proven potential to quantify the risk associated with such variables and integrate alternative scenarios and management strategies into the evaluation process. In this paper, a risk quantification model is developed that successfully quantifies the risk associated with dilution, as a function of production rate. This model is then validated in a case study on the Chuquicamata Underground Mine project. Keywords real options, risk management, risk quantification, dilution, minine planning.

Jul 1, 2013

By S. M. Spottiswoode

The aim of the hybrid location method is to improve seismic event locations by reducing the effects of errors in the wave velocity of ray paths between each event and each recording site. We report on further enhancements made to the hybrid location algorithm, which is based on the double-difference method developed by Spottiswoode and Milev1and Waldhauser and Ellsworth2. The term ?double-difference? refers to the residuals between the observed and theoretical travel-time differences and are obtained using either picked arrival times or various measures of time differences obtained from waveform pairs. These residuals are minimized for pairs of earthquakes at each station while linking together all observed event-station pairs. An important enhancement is that the double-difference term uses the median arrival time residuals to reduce the effect of outliers on the system of equations. In addition, the hybrid locations are further constrained by considering events of known locations, in this case along lines of development blasts. We relocated some 20 000 previously located seismic events in the Driefontein 5E area; 5 800 of these events were considered to have been development blasts and we constrained their locations to lie on the straight lines joining about 2 150 survey pegs from the mine?s database. Relocated events were shown to distribute more closely around advancing faces than had been the case before relocation. Wave velocities from the development blasts show evidence of anisotropy.

Jan 1, 2005

By J. T. Nel

Non-transfer-arc linear plasma systems are highly suited to manufacturing nanoparticles. In this paper, the manufacturing of such particles with specially designed plasma systems is discussed. In general, it entails the volatilization of a metal halide that is injected in the high-temperature region of a plasma flame, where it is reacted with a suitable reagent, for example O2, to produce nanooxide powders. Metal powders can also be introduced directly in the plasma. Due to the very short residence time of only milliseconds in the reaction zone, as well as the fact that the reaction takes place in the gas phase, combined with very rapid quenching in the order of 10 000°C.s-1, nanoparticles are produced. At Necsa the manufacturing of such particles has been demonstrated on various scales. A pilot plant for the production of nano-Al2O3, and two pilot plants, one using SiCl4 and the other one using SiF4 as feed material, were built to produce fumed, pyrogenic, nano-SiO2. The alumina plant had a production rate of 8?10 kg.h-1 and the silica plants had production rates of 2 and 10 kg.h-1 respectively. Perfectly spherical alumina particles with a particle size distribution of between 10 and 200 nm were produced on a continuous system. Particle size analysis for the silica by SEM measurements showed a d50 of 60 nm and a particle size distribution of 30?100 nm. The specific surface area was in the range of 170m2.g-1. Other samples of plasma produced nanoparticles such ZnO and B4C will also be presented.

Jan 1, 2010

By D. F. Malan

This paper presents an overview of work conducted over several years to investigate the continuous stope closure profiles recorded in tabular excavations and the use of this data as a hazard indicator. In spite of the brittle nature of the rock, measurements in gold mines and intermediate depth platinum mines revealed a significant time-dependent closure component. Various approaches to simulate the time-dependent closure have been investigated. Viscoelastic theory is able to simulate the time-dependent closure behaviour, but there are subtle problems with the use of this theory as it cannot simulate the failure processes in the rock. To overcome these problems, continuum and discontinuum elasto-viscoplastic models were developed by the authors. Discontinuum models have the advantage of being able to simulate the creep behaviour of prominent discontinuities. Development of these models has led to useful insights into rock mass deformation and has made the numerical simulation of parameters, such as rate of mining, possible for the first time. A number of practical applications for the mining industry have been developed from this study. Among these are the delineation of geotechnical areas using closure data, use of the data as a hazard indicator and to give warning of large collapses in the platinum mines, identification of areas to be preconditioned in the gold mines, measurement of the effectiveness of preconditioning and improved da

Jan 1, 2007

By W. J. Schlitt

The Namibian Copper Joint Venture has been formed to undertake development of the Haib copper deposit, one of the largest undeveloped copper resources in Africa. The development programme includes extensive hydrometallurgical testwork that is being managed by Kvaerner Metals (formerly Davy International).Various parts of the programme have been contracted to four third-party laboratories. The testwork involves sample selection and characterization, amenability tests, and a parametric study on the leaching variables. All portions of the programme are described and the results a represented. The ores selected for testing are quartz feldspar porphyries. The amenability tests include ?mapping? studies to assess optimum leach conditions, tests at high oxidation potentials, oxidation with various bacterial strains, and heap leach modelling. The parametric programme includes such variables as ore grade, leach temperature, crush size, pH, and ferric iron content of the lixiviant. Testing was done on both whole ore and concentrate. Results show that bacterial leaching is effective and that ore grade and temperature are key variables. Crush size and pH have less impact on copper extraction. For mid-grade ore, about 0.25 per cent copper, extraction is projected to reach 50 per cent after two years when heap leaching tertiary crushed ore at 60°C and pH 1.5. The heap leach operation would fit well with the proposed roast-leach operation used to treat higher grade ores. The latter could supply the low cost heat and acid needed in the heap leach.

Jan 1, 1999

By A. W. Breed

The bioleaching of arsenopyrite, the oxidation of arsenate and the precipitation of ferric arsenate are competing reactions, hence their rates depend on the relative concentrations of the respective species, and the activity of the bacterial culture. Bacterial arsenic resistance may be attributed to the Pst+Pit-mutation and an energy dependent efflux pump. Pst+Pit-mutations result in a reduced uptake of arsenate. This enables the bacteria to survive in solutions in which the arsenate concentration is significantly higher than the arsenite concentration. However, the excretion of arsenate requires energy. Therefore, in the absence of an energy source or during periods of reduced bacterial activity, the inhibitory effect of arsenate may manifest at concentrations to which the culture has been adapted. The chemical ferric leaching rate of pyrite and arsenopyrite decrease with a decrease in the solution redox and may be described using a modified Butler-Volmer equation. The bacterial ferrous-iron oxidation kinetics of L. ferrooxidans also depend on the redox potential, and can be described using a Michaelis-Mententype model modified to account for both temperature and pH. A model developed using the independently determined ferric leaching, and ferrous-iron oxidizing kinetics, has been shown to compare well with the experimental data for the continuous bioleaching of pyrite. Keywords: Leptospirillum ferrooxidans, arsenopyrite, bioleaching, sulphide minerals ferrous-iron oxidation kinetics, ferric leaching kinetics, redox potential

Jan 1, 2000

By K. Drescher

Excavations in deep level hard rock mines show rheological or time-dependent deformation responses to mining-induced stresses. These are generally not as dramatic as those seen in soft rock environments, such as potash and salt mines, but these deformations can nevertheless become substantial in time. It is usual to see total excavation closure at a much earlier stage than predicted by numerical models, and real-time measurements underground have confirmed that closure takes place on a more-or-less continuous basis, with highest closure rates observed after a blast and then slowly diminishing with passing time. This paper describes laboratory tests to determine the time-dependent response of hard rocks to loading, the results of the tests, and then quantifies these effects to explain the time-dependent phenomena observed underground. The primary intention of this work is to help explain the various time-dependent deformation processes around typical deep level hard rock tabular excavations. Three mechanisms were investigated in two typical hard rock types present in the deep level gold mines in South Africa, namely Ventersdorp Lava and Elsburg Quartzite. Uniaxial compression creep studies were done as the first part of the study followed by shear creep studies on discontinuities where crushed lava and crushed quartzite as well as a natural gouge were used as infilling. The last part of the study consisted of triaxial post-failure relaxation tests. The compression creep tests and the triaxial post-failure relaxation tests showed that the amount of energy dissipated by the lava is significantly less than for quartzite. For mines operating at depths greater than 2000 m the implication is that the lava must show a greater rockburst-proneness than the quartzite. Since the lava shows a lower post-failure stress relaxation, it can store sufficient energy for multiple rockbursts, which is seen in the clustering of multiple seismic events in the deep level mines. This study provides the first data available for energy change calculations in fractured rock masses, and provides the first general indications for rockburst intensities ahead of active mining faces.

Jan 1, 2003

By A. Butler

This paper explains the politics of mine nationalization in contemporary South Africa. Nationalization and privatization typically occur in the oil, mineral resources, and state utilities sectors, and they tend to follow one another in a long-term cyclical pattern. The paper explains why the current international environment has encouraged demands for nationalization and other forms of ?resource nationalism? in the South African minerals sector. It goes on to describe how the resurgence of resource nationalism has been influenced by internal factional politics in the African National Congress. It concludes that nationalization is unlikely to be the outcome of current policy deliberations within the ANC.

Jan 1, 2013

By M. Sibanda

The diffusion of carbon in Co-5% Fe alloy was studied in a belt-type pressure system at temperatures of up to 1330°C and press loads or nominal pressures of 7 020 tons or 42±3 kbar. Under these conditions, this alloy is in the solid state. Discs of graphite and prealloyed Co-5%Fe were used to make up the diffusion couple. The diffusion coefficient increased with increasing press load due to the tendency of the low density graphite to dissolve in the metallic phase reducing the overall volume and increasing the density of the system. Furthermore, inhomogeneous plastic deformation may have promoted diffusion by creating defects in the alloy. Diffusion couples treated at atmospheric pressure exhibited graphite particles in the metal, while those treated at high pressures exhibited carbide in the form of Widmanstatten laths. Carbon analyses indicated increased carbon solubility with increasing pressure. This was confirmed from calculated high-pressure phase diagrams.

Jan 1, 2005

By F. Enslin

Heavy metals and sulphates in acid mine drainage (AMD) can beadsorbed onto bentonite clay, leaving clean water and a heavy metal loaded clay precipitate as products. Due to the toxicity of heavy metals, the clay could not be disposed of safely in the past. A method was thus required to remove the heavy metal content from the clay. Acid leaching was proposed to liberate the heavy metals from the loaded clay. Sulphuric, nitric and hydrochloric acid were considered as lixiviants. Loaded clay samples were leached over a range of pH values from 1 to 3.5 to identify an optimum leaching condition. From the results it was found that metals can berecovered from loaded bentonite clay by means of acid leaching and the optimum pH for heavy metal liberation was found to be 2.5, with uranium as an exception, being optimally leached at a pH of 3. This allows for the possibility of selective leaching. Furthermore, X-ray diffraction analyses indicated that the clay structure did not deteriorate significantly during acid leaching, suggesting that the bentonite could be reused. The treatment of AMD with bentonite clay, and subsequent acid leaching of the clay, is a sustainable solution, and current outcomes could possibly lead to industrial implementation of the process during water purifying and metal recovery from waste streams. Keywords: Acid mine drainage, bentonite, heavy metals.

Jan 1, 2010

By J. van der Merwe, D. Tharandt

The corrosion behaviour of 304L stainless steel laser-cladded with various amounts of ruthenium (Ru) was evaluated in solutions of sulphuric acid and sulphuric acid plus sodium chloride at 25°C and 45°C by open-circuit potential and cyclic potentiodynamic polarization tests. In general, the addition of Ru to the stainless steel increased its corrosion resistance in 1 M H2SO4, as well as in 1 M H2SO4 plus 1 wt% NaCl. This was observed for a number of parameters such as corrosion rate, corrosion potential, open-circuit potential, and current density. However, increasing the amount of Ru added beyond a certain level did not result in further improvement in corrosion protection. For each environment there is an optimal Ru concentration for the best corrosion protection. For example, in 1 M H2SO4 at 25°C, 2.44 wt% Ru shows the least active surface in terms of corrosion. Further research into ruthenium coatings on stainless steels is recommended.

Jan 1, 2015

By B. Ulrich

The basis of this paper is a compilation of work in the design and construction of copper heap leach facilities, and interviews with various heap leach operations personnel in Chile and Peru. The purpose is not to highlight specific mines and their performance, but rather to discuss geotechnical/civil features of copper heap leach facilities that function well, as well as features that do not. During the 1990s several copper heap leach facilities were brought on-line in South America. Many of these facilities have now been operational for a number of years during which time the operators have been able to monitor the performance of their heaps. This paper serves as a compilation of operators? experiences, and provides a discussion of the lessons learnt over the past decade. Several key geotechnical issues are examined, focusing upon the integrity of the ore, drainage material and pipe network, along with the success of inter-lift liners. This conference provides a timely update of the original paper (Burkhalter et al, 2002).

Jan 1, 2003

By Rajendra Singh

Underground depillaring of contiguous coal seams/sections is a difficult problem, which becomes even more complex if the interburden/parting between them is thin. Conventionally, the depillaring with caving of contiguous seams/sections is done in descending order. However, if the parting is thin, the influence of the top sections/seams working over the standing pillars of bottom the sections/seams becomes extremely important for the safety and optimal exploitation of coal. Field investigations were carried out at Nowrozabad East mine where superimposed pillars of the Johilla top section were depillared above the developed pillars of the Johilla bottom section with a 3 m thick parting between the two sections. The competency of the 3 m thick parting (which consists of alternate layers of shale, sandstone and shaly sandstone) was improved by reinforcement (underpinning). The strata control investigations did not show any considerable instability problem of the 3 m thick reinforced parting and pillars of the bottom section due to top section depillaring. On the basis of this field investigation and a laboratory study on simulated models, simultaneous extraction of both the sections, along with reinforcement of the parting, was suggested for the geomining conditions of the Johilla top and bottom sections. Adopting the suggested simultaneous depillaring process, two sub panels of Johilla top and bottom sections have successfully been extracted without any strata control problem. This paper presents this case study along with the results of the strata monitoring conducted to evaluate performance of the underground structures during the field trial.

Jan 1, 2004

By L. Arnberg, E. Ott

The microstructure of ferrosilicon is important since it controls the disintegration of the material during crushing and thus the generation of fines. Therefore a study of the microstructure formation during solidification of pure FeSi(75wt%Si) and FeSi(75wt%Si) containing 1.2wt%Al and 0.2wt%Ca has been initiated. The material has been cast into rods of 8mm diameter, which have been remolten by induction heating and directionally solidified in a Bridgman apparatus. This allows the temperature gradient and the growth rate to be controlled independently. The temperature history during solidification has been recorded by a thermocouple in the melt. Growth rates have been varied between 5 and 400µms-1 and temperature gradients between 3 and 14°Kmm-1. The microstructures show a large dependence on the solidification conditions. The crack formation in the alloys has been studied and found to be strongly related to the microstructure.

Jan 1, 2004

By S. Lin

A new hydrogen production process, named the HyPr-RING, has been proposed. Fundamental concept of the HyPr-RING is integration of water carbon reaction, water-gas shift reaction and CO2 absorbing reaction in a single reactor. Firstly, thermodynamic analysis was done to judge the possibility to realize the process. It was found that high pressure and temperature condition, such as 20 MPa and 1000 K, is required to promote this integrated reaction. Next, experimental verification of the new process was done under the high pressure and temperature reaction conditions. As the results, integration of above three reactions in a single reactor can be done successfully and produced a large amount of hydrogen as estimated by thermodynamic analysis. Experiments showed that organic materials including coal, heavy oil, biomass, plastics can be used in this process. In the gaseous phase, no pollutants such asH2S, SO2, COS are detected so that gas cleanup system is not required for power generation when this process is used. Finally, a process design was made to estimate process efficiency. Theoretically, 1 mole of carbon can generate 2 moles of hydrogen and cold gas efficiency of this process estimated as more than 80 per cent. The process potentially reduces hydrogen production cost compared with the conventional hydrogen production methods. Keywords: Hydrogen, Fossil fuel, Energy, Process, Supercritical water

Jan 1, 2001

By P. C. Schutte

Ergonomics is the scientific discipline concerned with the understanding of interactions among humans and other elements of a system, and the profession that applies theory, principles, data and methods to design in order to optimize human well-being and overall system performance. Despite the fact that the application of ergonomics principles can make a major contribution to the management of significant occupational safety and health risks, ergonomics is currently applied on a limited scale in the South African mining industry. The objective of this paper is to provide a perspective of ergonomics, the main aim being to create a point of departure for the development of strategic objectives to enhance existing health and safety initiatives through the application of sound ergonomics principles. Two of the major consequences of poor ergonomics, namely work-related musculoskeletal disorders and worker fatigue, and possible means of introducing ergonomics into the South African mining industry, are discussed.

Jan 1, 2005

By P. J. Hancox

Heavy mineral deposits have been known from Liberia since the1950s from both river and beach placers. The heavy mineral content of beach sands ranges between 28?62% and the suite includes ilmenite, rutile, zircon and magnetite. These occur together with kyanite, sillimanite, staurolite and garnet. The average ilmenite content is 82% with minor zircon (11%), rutile (6%) and monazite (1%). The ilmenite is, however, of poor quality with haematite intergrowths and a titanium content ranging from10?42.4% (average ±25% TiO2). The amounts of rutile and zircon, while of suitable quality, have also previously been deemed too low for economic exploitation.

Jan 1, 2000

By H. W. J. P. Neomagus, R. K. K. Mbaya, J. R. Bunt, N. T. Leokaoke, N. W. Makgobelele

Silicon Smelters consumes more than 80000 t/a of wood-derived charcoal as carbonaceous reductant in the production of silicon metal. More than 10% of this material is discarded as fines (<6 mm) generated due to abrasion during processing. Charcoal fine residues (<650 μm) and polyvinyl alcohol (PVA) binder were used in this study to produce mechanically strong charcoal briquettes for metallurgical application as carbonaceous reductant. The PVA binder was added in mass percentages of 1, 3, and 5 wt% to the charcoal fines. The compressive strength, abrasion resistance index (ARI), drop shatter resistance (SRI), and water resistance index (WRI) were measured as functions of curing for up to 7 days under atmospheric conditions, and the results compared with metallurgical grade coarse charcoal. The ash content of the produced briquettes was found to be high (6.6–8.0%) compared with the coarse charcoal (1–3%). The 3 and 5 wt% PVA-bound briquettes were found to be the strongest, with compressive strengths of 40 and 115 kg/cm2 respectively, with WRI values of 75 and 73% respectively. The produced briquettes were found to have lower ARI and SRI values compared to the coarse charcoal. Future work should include beneficiation of the fine charcoal discards prior to briquetting, and an increase in binder addition to above 6 wt% to improve the ARI and SRIn.

May 1, 2021