Search Documents

By H. L. Monro

Al forward sales are made on the spot market, and are counter productive because they can only lower the price of gold, as one would expect from any additional supply of gold. Hedging against any further fall in the price of gold can be carried out on one of the World's Futures Exchanges in the same way as other commodities.

Jan 1, 1993

By J. T. Davies

Note: Melting techniques in the iron foundry by J. T. DAVIES* INTRODUCTION The selection of melting equipment for use in an iron foundry has for several years been the subject of numerous discussions, papers, and conferences. The controversy that has raged throughout the world has been brought about by the following factors: IF AC Symposium The 2nd IF AC Symposium on Automation in Mining, Mineral and Metal Processing will be held from 13th to 17th September, 1976, at the Carlton Hotel, Johannesburg. Advance registration takes place on 12th September, 1976. World phosphates The Minerals Bureau of the Department of Mines has released the second publication in its series of reports on the economic aspects of minerals that are of particular importance to South Africa.

Jan 7, 1976

By R. E. Gundersen

Hydro-power-the use of high-pressure water as an energy source-offers tremendous benefits for environmental control in deep, hot mines. The extent of these benefits depends on the mining method, the selection of equipment to be hydro-powered, and the efficiency with which the coolth is extracted from the water and into the working environment. The engineering of hydro-power systems continues to receive much attention. However, this paper considers the environmental implications of using hydro-powered equipment, particularly with regard to positional efficiency. The integration of hydro-power with developments such as backfill, mechanization, and higher face-advance rates is discussed. Layouts are proposed that attempt to minimize the quantity of water in circulation by extracting the maximum coolth from the water.

Jan 1, 1990

By A. J. S. Spearingt

The hydraulic transportation of relatively dense slurries for backfill purposes is typically carried through vertical and horizontal pipelines under gravity. Wear in backfill pipelines has become such a major problem that it is now one of the main reasons for the relatively slow build-up of placed backfill in spite of encouraging performance results in the gold-mining industry. This paper describes tests on pipeline wear that were carried out on classified tailings from the backfill plant at Vaal Reefs East. The testwork was carried out under various conditions of slurry relative density, slurry velocity, and pipeline diameter. Empirical relationships are presented for each transportation and pipeline parameter evaluated and, finally, overall relationships between pipeline conditions and transportation parameters are proposed.

Jan 1, 1992

By B. J. Ralph, I. J. Corrans, B. Harris

In the first section, a brief background to the practical and theoretical aspects of bacterial leaching is presented. Descriptions are given of present and potential methods for exploiting bacterial leaching in metal-winning. In the second section, the results of recent research are presented. The aim of this work was to obtain a greater understanding of the mechanism of bacterial leaching of sulphide minerals. Bacteria were observed to catalyse leaching reactions by oxidising ferrous ions to ferric ions, by removing protective films at the mineral surface and by depolarising cathodic areas.

By H. M. Wells

The investment decision under uncertainty by H. M. WELLS, Pr. Eng., M.Se. (Fellow) The future outcome of a proposed investment is uncertain at the time the decision must be made to accept it or reject it. This uncertainty can be expressed in the form of a probability distribution. An attempt is made to rationalize the investment decision under these circumstances, especially when the range of possible outcomes extends into both the acceptable and unacceptable domains. A rigorous definition of risk is proposed, and a criterion of risk aversion is developed that forms the boundary between acceptable risk and unacceptable risk (called the loss limitation line). It is shown that this decision criterion can also serve as a quantitative yardstick in the evaluation of various possibilities for 'tailoring' the proposal to mlke it more compatible with the particular financial circumstances of the company concerned.

Jan 4, 1976

By H. G. M. Rose

Contribution to the above paper by H. G. M. Rose* (Fellow) INTRODUCTION Dr Lawrence is to be congratulated on his most interesting and instructive paper, particularly on his suggestion for a model to increase mining productivity through improved management performance. In view of an experiment initiated in one Union Corporation mine (Mine A) and later extended to a second mine (Mine B), it might be of interest to review the many human factors involved and the initial productivity results achieved.

Jan 7, 1974

By M. G. Demmer

South Africa ranks among the top three mineral producing countries in the world, and yet the country's teaching and student population have a very limited knowledge of the mining and metallurgical industry. This is probably one of the major reasons why so few scholars elect to study mining-related disciplines at local universities, or to consider a career in the industry. Small mines Much interest in the development of small mines has been evident in the past few years, with junior companies taking the bull by the horns and moving in where larger companies found it uneconomic to tread or, indeed, where large companies are foresighted enough to see the advantage of smaller operations. Examples of small mines are to be found from Europe to Australia, in the Americas, and in

Jan 1, 1986

One of the important facets of The South African Institute of Mining and Metallurgy is its service to its members. One way of achieving this objective is by pursuing an active branch structure. In this Spotlight, Richard Beck, Holder of the Regional Development Portfolio, gives the aims of the Institute's branches, with a short note on each branch prepared by the regional chairman. Aims of the Branches: The primary aims of the Branches of The South African Institute of Mining and Metallurgy are those of the Institute itself: to further the interest of its members, to uphold the status of the mining and metallurgical profession, and to promote the image of mining and metallurgy. Beyond these 'high' objectives, the branches have a special function in providing a more intimate relationship between the Institute and its members. The branches enable members who live outside the Johannesburg area to participate in the affairs of the Institute to an extent that would not otherwise be possible and that they themselves can define. This is achieved through the holding of social events, colloquia, and visits.

Jan 1, 1990

By M. B. Algeo

Discussion of the above paper M. B. ALGEO The management and staff of Buffelsfontein Gold Mining Company Limited are to be congratulated on the excellent performances described in the paper presented by Mr Christos. In this day and age, with the current economic and labour situation, the mining industry is being constantly pressed to increase the productivity of ever-diminishing quanta of resources. Stress in rock The ISRM Symposium, 1976 is to be held in Sydney from 9th to 13th August, 1976. It is being organized by The Australian Geo. mechanics Society as a regional symposium of the International Society for Rock Mechanics. Thermal analysis The First European Symposium on Thermal Analysis will be held at the University of Salford on 20th to 24th September, 1976.

Jan 12, 1975

By Arvi Parbo

I would like to use the occasion to reflect on how the world environment for the minerals industry is undergoing substantial change, and how this change may affect the industry. I have given my talk the title 'The Quest For Competitive Edge', because the net effect of the changes taking place is that competition is increasing. To set the scene, let us look back at the situation which has existed in our industry in the past.

Jan 1, 1993

As a token of their gratitude, former pupils of Professor Lucien Denoel, a lecturer on coal-mining in the University of Liege, over a period of forty years, have founded the LUCIEN DENOEL prize. It is awarded, regardless of nationality and diplomas, to the author of a thesis dealing with coal-mining, ventilation, mine-draining methods, the use of explosives in the mine or coal-preparation. The thesis must show a truly scientific approach and considerable originality, and must not have been dealt with in a previous publication. The prize is 60.000 Belgian francs. The articles must be written in French, Dutch, German or English, and contain not more than 10,000 words, figures included. They must be forwarded, in triplicate, to the 'Jury du Prix Lucien DENOEL, c/o A.I.Lg., 22, rue Forgeur, Liege, Belgium,' before 1st July, 1970. The examining board reserves the right to publish the winning thesis in a Belgian magazine.

By A. L. Hinde, P. J. D. Lloyd, A. R. Atkins, J. G. MacKay

The control of milling circuits by A. R. ATKINS, M.Se. (Elee. Eng.) (Visitor), A. L. HINDE, S.Se., Ph.D. (London) (Visitor), P. J. D. LLOYD, S.Se. (Chem. Eng.), Ph.D. (Cape) (Fellow) and J. G. MACKA Y, S.Se. (Chem. Eng.) (Visitor). The general behaviour of mills is described in an attempt to find a control philosophy that will permit milling circuits to produce a constant particle size. Although the experimental work has been confined to a single section of the milling circuit of one mine, it is felt that the findings are applicable to other milling circuits.

Jan 6, 1974

By W. A. Hustrulid

CONTENTS PART I The theory of percussive rockdrill operation. Blow frequency Piston impact velocity and blow energy Thrust requirements Prediction of penetration rate Drillsteel life Bit wear PART II Measurements of percussive rockdrill performance Thrust-penetration rate measurements Blow frequency Piston impact velocity and blow energy Prediction of penetration rates The effects of hole diameter Thrusts applied by men Bit wear Appendix I Experimental procedure and rockdrill and drill steel specifications Appendix II Piston impact velocities and energies PART III Practical implications. Provisions of adequate thrust Conclusions INTRODUCTION In South African gold mines some 100 million tons of rock are broken each year by drilling and blasting. Only minor improvements to this method of rockbreaking have been made since the general introduction of pneumatic rockdrills for stoping 50 years ago and, more recently, of drillsteels tipped with tungsten carbide. The combined total cost of drilling and blasting amounts to almost R0,50 per ton of rock broken, which is just short of one quarter of the direct cost of stoping or development. Rockdrilling accounts for about R0,25 of the total cost of rockbreaking, of which RO,12 represents labour costs and R0,13 the cost of drillsteels, rockdrill spares and power. Mine air compressors use over 7 X 108 kWh of electric energy a year, amounting to 7 percent of the total electric power used by the gold mining industry. The efficiency of percussive rockdrilling is, therefore, of considerable significance to mining costs. Over the past four years the Mining Research Laboratory of the Chamber of Mines of S.A. has been engaged in experimental studies of percussive drilling. These experiments were conducted at test sites on Robinson Deep Gold Mine and Vlakfontein Gold Mine, made available by Gold Fields of South Africa, Limited. Three rockdrills, designated types A, Band C, of different manufacture, were used in the experiments which involved the measurement of the following operating characteristics: 1. Throttle air pressure 2. Applied thrust 3. Penetration rate 4. Air consumption 5. Blows per minute 6. Drill steel revolutions per minute. The results of these investigations are presented in three parts. Part I, "The theory of percussive rockdrill operation" which provides a concise, mathematical description of the performance of a percussive rockdrill in terms of its principal mechanical dimensions and operating conditions, and an analysis of the bit and gauge wear of drillsteels. Part II, "Measurements of percussive rockdrill performance" in which the experimental results are presented in terms of thrust-penetration rate curves at different throttle air pressures and throttle pressure-air consumption curves, which are shown to agree well with the predictions of theory. In addition, data relating gauge wear on the drillsteel and penetration rate to the distance drilled are discussed. Part III, "Practical implications" in which an analysis of the status of thrusting devices is made and the benefits that would derive from using uptimum thrusts are discussed.

By P. A. Botha

The production of iron and steel generates various types of waste materials containing oxides, carbon, and flux material. Usually, these materials are land-filled at the plant site or are hauled away for disposal. Some of these waste materials are hazardous, and they must therefore be recycled or disposed of properly. The influence of different waste materials in iron-ore sinter blends on the quality and operational parameters in sinter production is described. The recycling of waste materials such as dolochar, scrap fines, mill scale, electric-arc furnace slag, basic-oxygen-furnace mud via the sintering process can achieve a saving in the cost of the raw materials (for example, fuels and flux) and a reduction in pollution. A comparison of a typical sinter with a sinter produced through the utilization of waste materials shows a distinct correlation between certain types of waste material and some metallurgical properties and operational parameters. Dolochar (and arc-furnace slag) in a sinter blend acts as part of the fuel and flux that are normally added to a sinter mix. In general, dolochar improves the quality of the sinter and decreases the consumption of coke. Other waste materials adversely influence the quality of the sinter, but not necessarily the operational parameters such as the production rate. At Vanderbijlpark, approximately 15 kt of various waste materials per month are successfully recycled in the sinter plant. Investigations into the handling and recycling of other waste materials may indicate that even more waste materials can be utilized.

Jan 1, 1993

By A. Hinde, M. H. Moys

Tailings from metallurgical plants, when deslimed with hydrocyclones, provide a valuable source of material for the backfilling of mines. The effectiveness of this material as a support medium is a sensitive function of its particle- size distribution and water content. It is therefore important that the hydrocyclone-classification plants used to prepare the backfill are operated efficiently, and that the effects of feed disturbances on the composition of the backfil are minimized. This paper addresses the problem of the design, control, and optimization of classification plants to satisfy this need. The development of a computer program to simulate the dynamic behaviour of a hydrocyclone circuit of any given configuration is described. The use of the simulator to investigate the relative performance of conventional and innovative control strategies for single-stage and two-stage circuits is discussed in depth. The results of simulation studies are presented that indicate there is considerable scope for improving the performance and cost-effectiveness of backfill-classification plants.

Jan 1, 1991

By O. Korhonen, T. Leskinen

The use of large OK-16 flotation machines at the concentrators of Outokumpu Oy by o. KORHONEN and T. LESKINEN(Visitors) The development ofthe OK-16 flotation machine is described briefly, and an account is given of its use at various concentration plants in Finland. The benefits arising from the use of larger flotation machines are listed, and the technical specification of the OK-16 machine is detailed in an appendix.

Jan 6, 1976

By M. F. G. Bruce

Two backfill systems have been developed on West Driefontein, namely the centrifuge dewatered tailings system and the cyclone-classified tailings system. Modifications to the two systems since the publication of the original paper (Close and Klokow, 1985) are discussed in addition to the results obtained. Considerable experience has been gained from the operation of the centrifuge dewatering units as well as the placement of dewatered tailings in a difficult mine environment. The centrifuge dewatered tailings method has proved successful in the extraction of a highly stressed block of ground at No. 5A Sub-vertical Shaft. The utilization of backfill support in this area made it possible to dispose of a high-grade barrier pillar. This pillar was considered necessary prior to the introduction of backfill support. The recovery of the gold from this pillar made the use of dewatered tailings backfill cost- effective, despite high labour and maintenance costs. Current experience with the bagfilling method of placing cyclone- classified tailings indicates that it is viable and requires considerably less capital investment. Although expensive at present, it is envisaged that costs will decrease once cheaper bags and other forms of stope support are used. The placement of backfill in small-diameter sausage-type bags requires no change in mining cycle and allows the backfill to be placed close to the stope face. Both backfill systems are being expanded but preference is to be given to the cyclone-classified tailings system.

Jan 1, 1988

By R. M. G. Machunter

The dynamic behaviour of plant circuits and the available instrumentation determine the control strategies that are appropriate for the duty of the mineral separation plant. Although steady state modelling is appropriate to provide the main requirements of grade and throughput capability of a plant, it is the dynamic characteristics that determine the tolerance of the plant to disturbances and also its controller ability. This paper explores these issues with respect to the additional use of dynamic modelling to achieve these objectives.

Jan 1, 2007

By M. Le Roux

The dewatering of coal, and particularly fine coal, continues to challenge coal prepatration engineers to find a cost-effective solution. With known world oil reserves being depleted daily, it is envisaged that the future price of coal may justify the use of thermal drying to achieve lower coal product moisture levels. The effect of exposure of the coal to elevated toemperatures on the mechanical strength of the coal was investigated. It was found that temperature does not play a major role in determining the volume breakage of a particle and that other variables such as orientation during impact has a much greater influence. A double breakage mechanism was reported during the grindability tests. Surface, as well as volume breakage, occurs for the first 4 minutes while only surface breakage takes place thereafter. Due to this double breakage action, it was found that exposure to temperature does play a role in the amount of breakage and breakage rates during grindability tests. It was also concluded that a particle will break to an optimum size due to impact, after which only its surface will grind away as it is subjected to breakage forces.

Jan 1, 2008