Search Documents

By C. Holck, J. Yarmuch, J. Read

"Steepening of slopes provides the means to reduce waste extraction and increase ore recovery in open pit mines; however, it may also adversely affect safety by posing a higher risk of slope failure. The implementation of slope monitoring programmes is recommended to manage this risk inherent in steeper slopes. In this paper, the design and evaluation of monitoring campaigns to measure subsurface deformation and groundwater pore pressure in open pit mines is presented. The monitoring programmes were applied to a theoretical case of an open pit mine designed using DeepMine software (BOAMine SpA, 2015). Mine plans were developed based on the initial base case scenario with monitoring programmes considered for four types of monitoring instrumentation: two established technologies, in-place inclinometers (IPIs) and vibrating wire piezometers (VWPs); one emerging technology, the ShapeAccelArray (SAA); and a novel technology under development, the Enhanced Networked Smart Markers (ENSMs). Technical and economic appraisals of the monitoring programmes and sensitivity analysis of the developed mine plans showed that using ENSMs spaced every 4 m had the lowest cost per unit of data gathered. IntroductionSeveral open pit mines have already exceeded their design life and, as they become deeper and reach depths over 1000 m, they face higher rock stress levels and tensile deformations (Stacey and Xianbin, 2004; Stacey et al., 2003). The more complex the conditions in modern open pit mines, the more difficult it is to achieve long-lasting, stable pit slopes and to meet the mine’s economic needs: maximize financial returns, minimize risks to operational safety, achieve optimal ore recovery, and minimize waste extraction (Stacey, 2009). Steepening of slopes provides the means to reduce waste extraction and increase ore recovery (Stacey, 2009; Calderon and Tapia, 2006; Bye and Bell, 2001; Jefferies, Lorig, and Alvarez, 2008); however, it may adversely affect operational safety, as steeper slopes are less stable than shallow slopes (Steffen et al., 2008; Mphathiwa and Cawood, 2014)."

Nov 1, 2018

By G. S. Bartlett

The theme of this Colloquium, survival strategies, not only conveys a sense of urgency but also takes cognizance of the fact that, as in the political arena, tough decisions have to be made and acted upon in the years to come. It is therefore appropriate that the SAIMM, as spokesman for the metallurgical industry, should be dealing with these issues at this time, and I wish to commend the organizers of this Colloquium for focusing on a mater as important as the future of this great industry. In view of this, I regard it as an honour and privilege to officiate on this occasion, where the best of South Africa's brain power in the metallurgical field will be harnessed with a view to moulding strategies for survival.

Jan 1, 1993

By J. C. Vreugdenburg, W. A. H. Poppmeier

An overview of methods of manufacture is presented, as well as the results of laboratory experiments on the making of stainless clad steels. , It is concluded that stainless clad steel can be made in South Africa with existing rolling equipment, and that good bonding between the two materials depends on clean mating surfaces, proper edge welding, and a minimum reduction of 25 per cent at a rolling temperature of 120O"C. In practice, a minimum reduction of 70 per cent at 1100cC is recommended. : Suggested applications for clad steel include parts and equipment for the chemical, petrochemical, marine engineering, and mining industries, for the building sector, and for household appliances.

Jan 1, 1991

By V. C. Robinson

INTRODUCTION Most presidential addresses are in the nature of a review of some specific topic and this will be no different. In thinking about the subjects which might be suitable for this address I decided that as next month will see my retirement from the gold mining industry I might review the four decades since I started in the industry in 1929. These four decades have been more than usually in',~resting and exciting. They have covered a period when the price of gold increased from the old figure of 84/- an ounce to the price of $35 an ounce today, taking in on the way at least two periods of premium sales from which the producer benefitted. The industry in these four decades has survived the most totally destructive war in history and has seen fundamental changes in the political, economic and governmental life of South Africa. There have been great technological changes and improvements, some of which I shall refer to later, and in addition there have been profound changes in the relations between employer and employee in the industry which have affected not only the economy of the industry but the traditional thinking of both management and labour. I believe that the address presented to this Institute on the occasion of its 75th Anniversary by Mr Goode covered more than adequately the history of the Institute and the part it has played in the mining industry of South Africa. It would be merely repetitive, therefore, to discuss the affairs of the Institute of Mining and Metallurgy. Having said this, however, it is also necessary to point out that the history of the Institute is, and always will be, an important record of the history of mining in South Africa. There are many facets, however, on which we ought to look back and to re-examine. One of the most rewarding, but at the same time one of the dullest, places to look for historical facts is in the annual reports of the Chamber of Mines. I suppose that some of the dullest of these have been the reports for which paragraphs have been prepared by me personally. The notes which follow do not claim to be anything like a full record of this exciting period. RISE AND FALL OF THE GOLD MINING INDUSTRY In talking about the mining industry of South Africa it is inevitable that one talks, particularly in the historical sense, about the gold mining industry - an industry of fundamental importance which has made South Africa what it is and which has been dying since the early part of this century. In Table I is shown the progress of the gold mining industry measured by its output of ounces of fine gold from the beginning of operations until the end of 1969, and if you are interested in the productivity of the men who work this industry the table, composed entirely from figures set out in the Chamber's annual reports, also shows the production of gold expressed as fine ounces per European and fine ounces per Bantu worker over a long period. If you are still minded to think of this industry as dying then the last column in the table shows how uranium has played such a vital part in the prosperity of the country.

By P. R. Jamisch

The limitations of gold-mine evaluation by P. R. JANISCH, B.Sc. (Sur.) (Natal) (Visitor) Inherent uncertainty in the choice of parameter values places theoretical and practical limitations on the interpretation of a gold-mine valuation that are not necessarily removed by comparison of two valuations on the same assumptions. These limitations arise mainly in the estimates made of cost inflation and gold-price escalation, and lead to inconsistencies in the 'league table' method of investment analysis. The choice of discount rate is also critical in many cases. An approach to the overall problem that takes these limitations into account is suggested.

Jan 6, 1976

By C. L. Workmann Davies

Underground transport and communication in collieries was the theme selected for the 1983 mining school conducted by The South African Institute of Mining and Metallurgy. The response from the industry was so good that three separate schools of one week each were arranged, and a total of 222 delegates attended. Development of Mineral Resources The Institution of Mining and Metallurgy and The Department of Mineral Resources, Government of Thailand, with the cooperation of the Thai Mining Association and Chulalongkorn University, is to hold an international conference entitled 'Role of Government in Mineral Resources Development' in Bangkok from 5th to 8th Decembc -:" 1983. Electronics in Mining A symposium entitled 'Electronics in Mining', organized by The South African Institute of ElectriealEngineers, is to be held in Randburg, South Africa, from 18th to 20th September, 1984.

Jan 1, 1983

By G. H. Grange

Details are given of three legal controls for the pollution of the air, the water, and the land, together with brief histories of the developments leading up to these controls. Attention is drawn to the fact that legal action may be instituted against a mine under common or other laws where pollution causes proveable damage or loss. It is suggested that an international conference should be held to define the philosophies and principles on which to base not only the necessary legislation for environmental control but also the machinery by which the controls can be administered.

Jan 1, 1978

By M. A. von Below

Environmental activists have targeted the mining industry in an attempt to prevent development, which has resulted in the industry's becoming defensive and retro-active. This paper argues that mining managements should go on the offensive and champion the environment through leadership in environmental policy and research and development, rather than reacting to anti-mining campaigns. In the formulation of an environmental policy for the mining industry, a clear understanding of the concept of sustainable development is of paramount importance.

Jan 1, 1993

By J. J. Geldenhuys

The Institute revived a valuable tradition when, on the 19th of March, 1983, it held its first 'annual' banquet in some fifteen years. It was such a sparkling success that it is sure to be held more frequently in future. The success of the occasion was borne out by the fact that the main banqueting hall at the Wanderers Club was filled to capacity, with over four hundred members and guests.

Jan 1, 1983

By B. P. Watson

In South Africa, the Bushveld platinum group metal deposits are unique in that they are the largest platinum group metal deposits in the world. These deposits occur as two distinct stratiform tabular orebodies and strike for many hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2 000 m. The mining method is a variation of planar open stoping. Pillars are widely used to support the open stopes. Crush pillars are commonly used in this role, where the residual pillar strength provides the required support resistance to stabilize the stoping excavations. This paper describes the direct measurement of stress within these crush pillars, and describes the stress?strain behaviour of these pillars. These findings indicate that the measured pillar failure stress is too high. The implications of these findings are that roof damage and pillar bursting could occur, and some examples of this type of damage are shown. The paper concludes that this problem could be mitigated if the three dimensional pillar geometry were modified and the pillars were cut smaller.

Jan 1, 2007

By L. W. Helle

In this investigation, which was conducted at the Metallurgical Research Plant, Lulea, Sweden, a series of experiments were carried out using a water-model to simulate the gas rinsing of a ladle containing liquid metal. The factors examined include the effect of gas flowrate, the position of a porous plug or lance, the immersion depth of the lance, and the geometry of the bath at the time of complete mixing. Mixing times were recorded by conductivity measurements. The results showed that there is a threshold level for mixing above which no advantage is to be gained from an increase in the gas flowrate. It is suggested that the results can be applied to rinsing ladles in working situations, the levels being approximately 270 dm3/min for 40 t ladles and 780 dm3/min for 150 t heats. The optimum siting of the lance or porous plug is a position that is three-quarters of the internal radius from the centre of the ladle with the lance penetrating as deeply as possible into the ladle. The best design of liquid bath is that having a diameter-to-height ratio of I. An equation was developed for the calculation, by dimensional analysis, of the time required for mixing during gas rinsing, and a comparison of the calculated mixing times with the results from production trials shows a satisfactory agreement (with a correlation factor of 0,91). Thus, an equation is available for the calculation of the stirring time needed to completely mix the bath in production situations.

Jan 1, 1981

By R. I. Klintworth

The multi-reef area of Cooke 3 Shaft provides a unique mining challenge on account of the very thin middlings between the pay bands and the marginal values of the reef. It is uneconomic or impractical, because of the excessive heights, to mine the middlings using conventional stoping methods. The development of suitable mining methods is discussed with particular emphasis on the control of water inflow and the policy of not jeopardizing or sterilizing other reef horizons by the mining method implemented. No definite solution is currently available, but with the aid of instrumentation, computer analyses and mechanized mining equipment, the mine continues to attempt to maximize extraction and profits.

Jan 1, 1988

This report describes the investigational work on the development of a fire-assay method capable of concentrating, in a button of nickel sulphide, all six of the platinum-group metals present in samples of ores, concentrates, and mattes. In the method adopted, the sample is fused with a mixture of sodium carbonate, sodium tetraborate, nickel carbonate, and sulphur. The nickel sulphide formed during fusion collects the noble metals and carries them to the bottom of the crucible. The nickel sulphide button is dissolved, and the noble metals are isolated and determined. The coefficients of variation range between 1,0 and 4,9 per cent for the various platinum-group metals when they are present in concentrations between 0,3 and 75 p.p.m.

Oct 15, 1971

By D. G. Krige

By use of models based on the South African gold-mining industry, analyses are made of the effects of changes in the mining tax structure on the .State's tax income from potential new mines; also on the percentage of such mines likely. to be proceeded with. The percentage is affected by the correlation between changes in taxation and in the flotation pay limits !or new mines. It is shown that the State stands to gain both directly and indirectly from raising the level of the capital allowance and from its extension to all mines; and that the reduced taxation resulting from a lowering of the discriminatory high tax formula for the gold mines, would, in respect of potential new mines, be compensated for by a significant increase in the percentage of such mines that would be proceeded with.

Jan 1, 1979

By R. Falcon, A. J. Ham

This paper summarizes the characteristics of Southern African coals, presents a fundamental approach to the combustion performance of coal, and reviews some of the recent developments in the fields of technological evaluation and boiler design for coals typical of this region. This includes a summary of the petrographic constituents of coa~ highlighting the differences between the Palaeozoic coals of the northern and southern hemispheres (Laurasia and Gondwana respectively), and the effects of these properties on the combustion performance of coal as seen in terms of laboratory, pilot-scale, and full-scale operating conditions. Recent developments in boiler design linked to advanced characterization studies and commercial experience have led to unprecedented use, with maximum effect, of the low-grade, high-ash, high-inertinite coals typical of some parts of this region. In the light of this success, more adequate understanding and better methods of assessment of the coals typical of the Gondwana region are called for, particularly in the light of the price premium for high-grade coal and the more cost-effective lower grade coals on the international steam markets.

Jan 1, 1988

By P. R. Jochhens

The Past. In the past, large metallurgical companies (for example the mining houses) had the necessary infrastructure both to develop metallurgical flowsheets and to undertake the construction and project management of metallurgical plants. Effectively, the sole contribution by contracting companies was the supply, and possibly the installation, of specific items of equipment. OBITUARY: AUSTIN WHILLIER (1927 - 1981) On Thursday, 13th August, 1981, Dr. Austin Whillier passed away peacefully in Johannesburg after a long illness. This event has been a serious blow indeed, and its effects will be felt, not only by the Chamber of Mines of South Africa and the South African mining industry, but also throughout many scientific and technical spheres both in South Africa and further a field.

Jan 1, 1981

SABS quality mark for explosives* AECI Explosives and Chemicals Limited has been awarded the SABS permit to apply the SABS standardization mark to al its permitted NO explosives manufactured at Modderfontein.

Jan 1, 1989

By D. F. Malan

This study Investigates transient closure piles of tabular excavations. Measured closure profiles in stopes indicate that time-dependent acts f the rockmass can be very prominent but such effects have been largely neglected in past analyses and modelling. This was due to a poor understanding of the time-dependent mechanisms controlling closure rates This paper investigates the feas-ibility of representing the rockmass as a visco-elastic medium. Currently, no analytical solution for the viscoelastic convergence of a tabular stope is available in the literature. Therefore, the author derived a solution using the correspondence principle and a known elastic solution. It is assumed that the rockmass behaves elastically in hydrostatic compression and as a Kelvin substance in distortion A parametric study is Included to aid in the calibration of the model parameters, together with a discussion on the correct calibration of these parameters from experimental data.

Jan 1, 1995

The Annual General Meeting of the South African Institute of Mining and Metallurgy was held in Kelvin House, Johannesburg, on Wednesday, 19th August, 1981. Dr P. R. Jochens (President) was in the chair and declared the meeting open at 4.05 p.m. This account of the proceedings includes only those matters that are not reported under the heading `Annual report and accounts' elsewhere in this issue. Confirmation of the Minutes The minutes of the last Annual General Meeting, which was held on 27th August, 1980, were confirmed as pub¬lished in the September issue of the Journal. Welcome President: I extend a sincere welcome to you all, especially to the following distinguished guests: Mr L. W. P. van den Bosch, President of the Chamber of Mines, and Mrs van den Bosch; Mr J. G. Kirchner, Government Mining Engineer, and Mrs Kirchner; Dr William Ble¬loch; Dr L. Alberts, President of the National Institute for Metallurgy, and Mrs Alberts; Dr C. F. Habis, Presi¬dent of the CSIR, and Mrs Habis; Dr P. J. Hugo, Chief Director of the Minerals Bureau, and Mrs Hugo; Mr D. N. Stuart, General Manager of the Chamber of Mines, and Mrs. Stuart; the Presidents and representatives of other Institutes and their wives; and Honorary Life Fellows of our Institute and their wives.

Jan 1, 1981

By H. E. James

The 13th Congress of the Council of Mining and Metallurgical Institutions (CMMI) was held in Singapore from 11th to 16th May, 1986. Tours to Australia, Malaysia, Thailand, South Korea, and Japan took place the week before and the week after the Congress. Registrations By far the largest contingents at the Congress were from Australia (157 delegates and 65 affiliates) and South Africa (127 delegates and 99 affiliates). The other 25 countries represented at the Congress accounted for 118 delegates and 37 affiliates. Thus the total registrations amounted to 402 delegates and 201 affiliates.

Jan 1, 1986