Search Documents

By M. J. U. T. Van Wijngaarden

SYNOPSIS The corrosion characteristics of a new steel, 14Cr, which is a modification of the well-known 3CR12, in aqueous sulphate solution were studied through polarization diagrams and a computer analysis based on the polarization¬resistance technique. It was found that the corrosion rate of 14Cr steel is independent of pH for pH values above 6, but, below a pH value of 4, the corrosion rate increases sharply with decreasing pH. In air-saturated solutions of neutral and mildly alkaline pH, the corrosion rate is approximately 60 µm per year. The 14Cr steel shows a twentyfold improvement in corrosion resistance over that of 3CR12 in sulphate solutions at pH 2,0. This is considered to be due to the beneficial effect of its higher chromium and nickel contents.

Jan 1, 1985

By E. J. Magri, A. Couble

Kriging estimates of geological resources are sometimes conditionally biased because the kriging plan contains too few samples. This may be done purposely in order to match the variance of the estimates to the true block dispersion variance. This work aims at evaluating the influence of conditional bias over the ultimate optimum pit design in relation to its shape, size and NPV (Net Present Value of profits). It has been restricted to two real case studies: a ‘carrot shaped’ gold porphyry in northern Greece and a manto-typeexotic copper deposit located in northern Chile. The methodology applied to each deposit consisted of generating a ‘real block model’ and four resource estimates by the use of conditional simulation and the application of four different kriging plans to the drillhole databases respectively. The estimation models vary in smoothness and conditional bias. Ultimate optimum pits were determined for the ‘real’ and the four different kriging models. Pit comparisons lead to the following conclusions: •In the worst case, conditional bias overestimated the project's NPV by 32% and 5% for the gold and copper deposits respectively. •The overestimation of high grades is more relevant than the underestimation of low grades. This resulted in a tonnage over-extraction of 148% and 1% for the gold and copper deposit respectively. This difference was attributable to the vastly different geometry of the deposits. •The smoothing effect of kriging, without or very little conditional bias, produced open pits that were different to the ‘true’ (ideal) ones and furthermore, underestimated the project's NPV by 10% and 6% for the gold and the copper deposits respectively. •Other factors that influence the optimum open pit design and to some extent control the effect of conditional bias are: the cut-off grade, the orebody geometry and distribution of grades within it and the amount of over-burden. Keywords: conditional bias, ultimate pit design

Jan 1, 2003

By S. L. Miller

The development of a pilot gold geostatistical ore reserve system proved that geostatistical methods worked well for the routine production of annual ore reserves on gold mines of the Gold Fields of South Africa (GFSA) group, and that the techniques could also be practically implemented, understood and accepted by Survey Department personnel. Many side benefits of the pilot system became apparent, and a variety of useful management information was provided by manipulating the data values that were already captured. It was decided that it was a priority computing project to develop a standard production system (GORS) for routine use by all the GFSA gold mines. Experience with the pilot system enabled detailed functional specifications for GORS to be laid down. These, together with group computing policy determined the terms of reference and constraints for the GORS development. System design could not be finalized until new and appropriate mainframe database software and graphics workstation equipment and software had been found. With these in place the basic system was structured to take best ad- vantage of the interactive features of the workstation, the number-crunching power of the mainframe and the flexibility offered by a relational database and associated 4GL tools. Application sub-systems were developed for data capture, statistical applications, geostatistical calculations, contour plotting and graphical queries. GORS is being introduced to the mines in a phased manner with suitable documentation, training and support structures to enable it to be routinely and effectively used on a day-to-day basis by all group gold mines.

Jan 1, 1987

This paper illustrates the application of numerical modeling methods, in conjunction with limit-equilibrium techniques, to the location of critical slip surfaces in slope-stability problems. Initially, the Spencer slice-based method of analysis is introduced, together with a dynamic-programming algorithm for slip-surface location. This limit-equilibrium method is assessed critically through the use of an illustrative problem. The technique is then extended to locate the critical slip surface for a similar slope, but with more complex constitutive and yield relationships for the material comprising the slope. To this end, the use of the stress field generated from a finite-difference program, together with a dynamic-programming search routine, is presented as an advanced technique of slope-stability analysis for engineers.

Jan 1, 1993

By E. Uslu

The kinetics of the reduction of chromite from the LG-6 layer of the Bushveld Complex in Fe-Cr-C alloys were studied in the temperature range 15OO°C to 1680°C under an inert argon atmosphere. The rotating cylinder technique was used, and the rotational speed of the chromite cylinder ranged from 0 to 1000 r/min. The melt consisted of 30 to 80 per cent chromium and 2 to 8 per cent carbon. The initial chromium-te-iron ratios of the melts varied between 0,42 and 4,95. The reduction of chromite spinel was analysed in terms of the decarburization of the metal. It was found that decarburization increased with an increase in the temperature, the carbon content of the bath, and the rotational speed of the cylinder up to 400 r/min, after which it remained almost constant. Decarburization also increased with an increase in the chromium content up to about 50 per cent chromium but, at higher chromium contents, it decreased. In the early stage of the reduction, up to about 30 minutes of reaction time, the liquid-state mass transfer of oxygen was found to be the most likely rate-determining step. The apparent activation energy was calculated to be 84,864 kJ per mole of oxygen. In the later stage, diffusion of iron and/or chromium in the solid state is the most likely rate-determining step. The apparent activation energy for the diffusion was calculated to be 471,18 kJ/mol.

Jan 1, 1991

The structural design of a pavement relates to the ability of the road to carry the imposed loads without the need for excessive maintenance or rehabilitation. Current techniques for the structural design of haulage roads are empirical and based primarily on the previous experience of personnel assigned to pavement design, both in terms of the strength of the structure and the quality of the wearing course material. This has the potential for unwarranted expenditure on too thick a structure or, conversely, premature deformation leading to the need for excessive expenditure on maintenance. Furthermore, the effect of larger haulage vehicles on the structural performance of a pavement cannot be predicted. Thus, there is a need to develop a portable and practical method of structural design. This paper presents an overview of structural design methods for mine haulage roads and, through an analysis and quantification of the structural performance of existing pavements, recommends the mechanistic design procedure, together with a revised structural design and associated limiting design criteria. It is concluded that the application of the mechanistic method to a design project can reduce the costs of haulage roads construction and accrue additional benefit in terms of reduced operating and maintenance costs.

Jan 1, 1996

By D. Menne

A comminution model and a quick laboratory milling test procedure are presented. These allow the determination of milling parameters for the - optimization of ball size and pulp density in operating mills estimation of the performance of new feed stocks in an existing mill - estimation of the expected milling performance for a new project. Information on the estimation of the size of mills to deliver specified amounts of comminution energy, and amount of expected ball, rod, and liner wear to allow cost estimates for new projects, is also included.

Jan 1, 1983

By M. G. Spengler

Mr More O'Ferrall must be complimented on a paper that will be a useful reference for the re-working of previously abandoned workings. His paper so closely mirrors experiences at East Rand Proprietary Mines, Limited, that it could well have been based on occurrences in that mine. Corrosion The Scientific Society of Mechanical Engineers is organizing the 115th event of the European Federation for Corrosion in Budapest, from 18th to 22nd October 1982.

Jan 1, 1981

A number of issues relating to the computational aspects of pillar design are addressed in this paper. The computation of average pillar stress values is important when attempting to establish criteria for pillar design and in the analysis of the stability of tabular pillar layouts. One of the default ?classic? numerical methods that are used to determine pillar stresses is the displacement discontinuity method. In many instances it is not clearly understood that this approach does suffer from some limitations, particularly in relation to the fact that in coarse element simulations, the simulated average pillar stress (APS) can depend on the chosen mesh size. The nature of this error is highlighted in this paper and some strategies are suggested to bound the magnitude of these errors. It is demonstrated as well that the popular linear stiffness approximation to pillar or seam compressibility does appear to allow reasonably accurate estimates of the average pillar stress when either the pillar height is varied or when the seam modulus differs from the host rock modulus. A practical implication of this study is that if the seam modulus is noticeably lower than that of the host rock, such as for coal seams, it is important to use a linear stiffness constitutive model for the pillars rather than a ?rigid? pillar assumption. This added complexity seems unnecessary, however, when simulating hard rock pillars in mines where the seam modulus is very similar to that of the surrounding rock.

Jan 1, 2011

By M. Andersson, R. Elsrud

The quality and the production rate for the mining operations in the Garpenberg mine has been much improved due to a new system, that presents the latest exploratory and planning data for the driller at the moment he deploys the drill rig at the face. Other components in this improvement work are better planning procedure, large-scale production system with longer rounds and introduction of new drill rigs in the mine. The new Rig Control System (RCS) for the new series Atlas Copco Boomers L2C has made it possible to develop this system for production drilling in the Garpenberg mine. The ABC Regular has been extended with map navigation and drill plan generator. The driller will have the best estimate of the orebody in front of him and the best drill plan for that orebody. The customer’s specific system will also become a standard Atlas Copco product for the Boomer ABC drill rig family.

Sep 1, 2001

By C. Ringas

Pipelines are used extensively in industry to convey various products. Internal corrosion of pipelines can lead to perforation and leakage of the product. A growing problem, not often accurately recognized, is internal corrosion of pipelines caused by bacteria. Microbiologically-induced corrosion (MIC) refers to corrosion caused by a variety of micro-organisms. This form of corrosion is not widely recognized in many industries, although it is widespread and causes many corrosion problems in pipelines, both internal and external. Sulphate-reducing bacteria (SRB) are responsible for the bulk of the corrosion problems caused by MIC. Corrosion caused by SRB is found extensively in water pipelines conveying raw, potable and waste water, as well as in pipelines conveying slurries. This problem also occurs in pipelines conveying crude oil. This paper describes internal corrosion problems of slurry pipelines caused by bacteria and outlines mitigation methods to improve slurry pipeline integrity, thereby extending the life of such pipelines.

Jan 1, 2007

By K. R. Vost

This paper reviews the theoretical methods used in South Africa for the prediction of heat pick-up and air-temperature gradients along main haulages. These methods include those of Starfield, Ramsden, McPherson, and Goch and Patterson. The differences in predictions based on typical airway conditions are explained as being due to differences in the mathematical models on which the predictions are based. The largest discrepancies were found for dry airways and for airways with bulk air coolers. The errors in predictions of the effect of machines and coolers that have been running for only a few months are calculated, and the limitations of various simplified methods are discussed.

Jan 1, 1982

By J. D. Flint

The geological conditions in the Vierfontein area ~re such that conventional pillar extraction ~stooping) cannot be practised safely or efficiently. Both the open-end lift and the pocket-and-fender methods of pillar extraction have been tried with little success because of problems with roof control and ground stability. The main reasons for the difficulties are the coarse-grained sandstone roof, local weaknesses in the coal seam, and the rate at which the pillars were extracted. The mine has practised bord-and-pillar mining since it started production in 1952, and considerable reserves of coal are contained in the pillars. As an alternative to total pillar extraction, in which hand-loading methods were practised, a system of partial pillar extraction using mechanized-mining methods ~11"modified goaf-line support has been evolved. These remnant coal pillars (snooks) remaining after partial extraction ofthe pillar, together with the installation of 1,2 m" matpacks and a double line of fullcolumn resin roofbolts, ensure control of the edge of the area that has been mined out (goaf). Where roof conditions preclude the use of conventional pillar-extraction methods, this method holds promise as a safe and efficient alternative for the recovery of coal from pillars and for an increase in the volumetric extraction of the reserves within a mining panel.

Jan 1, 1984

By J. M. Paull, J. B. See

The rate of reaction between different carbonaceous reducing agents and silicon monoxide gas was studied by the use of a technique developed in Norway by Tuset and Raaness. Argon carrier gas was used to pass a known fixed concentration of silicon monoxide gas through an I1 cm3 sample of precalcined reducing agent at 1650°c. Silicon monoxide gas was generated by the heating of a mixture of silica and silicon carbide, and the progress of the reaction was followed by monitoring the carbon monoxide in the off-gas with an infrared spectrometer. The reactivity of silicon monoxide gas towards a number of carbonaceous reducing agents (charcoal, Iscor coke, Lurgi char, and petroleum coke) was shown to be similar to results obtained with the carbon dioxide reactivity test. The silicon monoxide reactivity test was able to indicate the extent to which fines were generated when the reducing agent was converted to silicon carbide. Of the reducing agents studied, Lurgi char appeared to be the most suitable for the production of ferrosilicon because it has a high reactivity towards silicon monoxide gas and high strength when converted to silicon carbide. So that industry could be given some indication of the suitability of certain reducing agents for the production of ferrosilicon and silicon metal, a reactivity scale similar to that of Tuset and Raaness was constructed that compares the volume of silicon monoxide gas required by a reducing agent to reach a carbon monoxide content of 10 per cent in the off-gas during the conversion of the reducing agent to silicon carbide. This scale assists in the selection of those reducing agents that require less silicon monoxide gas for conversion to silicon carbide, and that give savings in material and power costs because less silicon monoxide gas need be generated in the furnace.

Jan 1, 1979

By W. Wittke, D. Schröder, H. Polczyk

ABSTRACT: The Urft dam, the Diemel dam and the Eder dam are three old masonry damslocated in Germany. The paper describes the rehabilitation measures and the correspondingstability analyses carried out to adjust the dams to today's standards. Remedial works such as theexcavation of inspection galleries, the installation of a grout curtain with a downstream drainagescreen as well as the installation of pre-stressed permanent tendons were carried out. In all threecases the stability of the upgraded dam could be proven on the basis of finite element analyses. ZUSAMMENFASSUNG: Die Urft-, Diemel- und Edertalsperre sind drei alte deutscheSchwergewichtsmauern aus Bruchsteinmauerwerk. Im Beitrag werden Instandsetzungsmaß-nahmen und Standsicherheitsnachweise beschrieben, die erforderlich waren, um die Staumauernan den heutigen Stand der Technik anzupassen. Hierzu wurden Kontrollgänge aufgefahren,Dichtungsschleier mit luftseitiger Dränage sowie vorgespannte Daueranker hergestellt. In allendrei Fällen konnte unter Berücksichtigung der Instandsetzungsmaßnahmen die Standsicherheit derMauer auf der Grundlage von Berechnungen nach der Methode der finiten Elemente nachgewiesenwerden. RÉSUMÉ: Les barrages de Urft, Diemel et Eder sont trois barrages-poids vieux allemandsconstruit de maçonnerie de moellon. Dans cet article, opérations de remise en état et preuves destabilité sont décrits, qui étaient nécessaires pour adapter les barrages à l'état de la techniqueactuelle. À cet effet, des galeries de contrôle étaient creusés, voiles d'étanchéité avec des drains àla face aval et tirants précontraints permanents étaient fabriqués. Dans tous les trois cas, tenantcompte des opérations de remise en état, la stabilité de la barrage pouvait être prouvée à partir decalculs selon la méthode des éléments finis.

Jan 1, 2003

Now a new generation of computerized drill rigs has been launched and they are based on modern standard PC-computer technology. The rigs have been well embraced by the market and more than 100 units have left the assembly line. The new generation has taken a quantum leap forward with respect to drilling accuracy, logging capabilities, reduction of manpower in some types and serviceability compared to the previous generation of drill rigs. The Can bus technology, well proven in the automobile products, is the backbone in the new generation control system of Atlas Copco. The short-term development is now focused on establishing this new automation platform on other product lines of Atlas Copco products. The long-term objectives is to offer the mining industry Atlas Copco products with one common automation platform. Essential for Atlas Copcois to contribute to the work with the on-going Data Exchange standard between mining machines and mining computer systems (IREDES). Our belief is that an accepted standard will make mine automation programs affordable for a wider base of the mining industry, because of the possibilities to a cost effective integration of different equipment with a minimum of system integration problems and machine specific interfaces.

Sep 1, 2001

By R. L. Robinson

An analytical framework is formulated to assist mining companies in assessing the relative merits of mineral exploration and acquisition strategies. The anticipated costs, risks, and returns of each strategy are conceptualised using decision trees. Economic criteria - expected net present value, expected return per unit of investment, and the probability of success - for each strategy are derived(from the appropriate decision tree network. Application of the analytical framework is illustrated using the example of a medium-size company in the Canadian base metal sector.

Jan 1, 1987

By J. P. Kirsch

This paper sets out to clearly identify all elements that make up an effective furnace feed system. These are outlined and the more common types of technology are listed. These technologies all play an important role in the final delivery of all feed materials to the furnace.

Jan 1, 2008

Corosion technology: An information source book, by Judith Ann Douvile. Taylor & Francis, 1989. 188 pp. £32. Stainless steel buyers guide 1990. Southern Africa Stainless Steel Development Association (P.O. Box 4479, Rivonia, 2128), 1990. Free. Fatigue and stress of engineering materials and structures, edited by H.P. Lieurade. ITT International (40 Promenade Marx-Dormoy, 93460 Gournay-sur- Marne, France), 368 pp. US$ 109. Titanium and aluminium, edited by P.A. Coulon. ITT International (40 Promenade Marx-Dormoy, 93460 Gournay-sur-Marne, France), 200 pp. US$ 80. Engineering applications of stochastic processes. Theory, problems and solutions, by A. Zayezdny, D. Wulich, and D. Tabak. Chichester, John Wiley, 1989. 525 pp. £54.50. Metal behaviour and surface engineering, edited by S. Curioni, B. Waterhouse, and D. Kirk. ITT International (40 Promenade Marx-Dormoy, 93460 Gournaysur- Marne, France), 413 pp. US$ 109. Fuzzy control and fuzzy systems, by W. Pedrycz. Chichester, John Wiley, 1989. 272 pp. £37.50. CILO (carbon-in-leach with oxygen) cost study, by Minproc Engineers (USA). Free.

Jan 1, 1990

By J. Markgraaff

Because composites offer new solutions to materials problems, they are currently the focus of intense research and development worldwide. However, the natural tendency of users is to remain with tried materials in every situation of material selection. This approach ignores the tremendous advances that have been made in composite materials and their application. These advances enable engineers to tailor composites to suit specific applications such as the demanding needs of mining and industry in South Africa. However, the application of composites, where new and improved components and products are needed or are being developed is often hampered by the limited knowledge and experience of the engineers concerned. This paper presents some of the basic information needed for an appreciation of the terminology, definitions, and properties of various types of composites. It also reviews recent developments in manufacturing technology and product development that may find application in local industries and mining.

Jan 1, 1996