Search Documents

By R. R. Mankowski, F. J. Cox

Experimental results are presented on the longitudinal atenuation of a kinetic shock wave traveling along a typical mine hoisting cable. Mathematical curve-fiting of the results established these losses to be exponential and tension-dependent. The reflection and power-transmission coeficients of a typical winding drum were also investigated. The degree of penetration of an incident stress wave onto the coil of cable wrapped round the drum is shown to be governed by a second-degree relationship, and is solely dependent on the acceleration of the cable at the cable-drum interface. Although the investigation is limited to the testing of a single hoisting cable, certain qualitative trends that were identified can be generalized and applied to other types of hoisting cable with diferent geometries, elastic properties, and instalations.

Jan 1, 1986

By A. A. Hazell

Mine management by objectives by A. A. Hazel The procedure of setting production targets is illustrated in Appendix I of the paper. This procedure is intended only as a guide although the standards on which it is based were established by work studies and found subsequently to be well within the limits of a trained crew.

The general standard of engineering in South Africa will, it is believed, reach new heights after the establishment of the S.A. Council for Professional Engineers (SACPE) in February, 1969. The Council is being created to establish standards for professional engineers in this country and ensure that the quality of engineering is maintained at a high level. In terms of the Act of Parliament under which the new Council will operate, all consulting engineers will have to be registered if they wish to remain in private practice. While engineers who are not in private practice cannot be compelled to register, it will be in their interests to do so, according to a statement issued by Mr M. R. Gericke, chairman of a Shadow Council which is at present preparing for registration and drafting the requirements for registration. Registration is seen as an important move towards maintaining the quality of engineering in South Africa. Engineers will be encouraged to strive for professional status by gaining the necessary qualifications and the varied range of experience required by the Council before registration. All work done by registered professional engineers will have to conform to certain minimum standards. A spokesman for the Council has urged all engineers to ensure that they apply for registration when the Act comes into force in February. The Council is also anxious to gain the co-operation of employers in ensuring that the holders of professional engineering posts will be registered. Full information regarding registration will be sent to engineers throughout South Africa early this year, and announcements will appear in the press.

By I. E. Lane

Conventional demand management techniques invariably fail to offer optimum control flexibility in an operationally complex gold mining environment. An improved control system for electrical demand management is proposed. The system is designed to provide more effective load scheduling and control strategies by means of a computer aided demand management system (CADMS). The objective of the CADMS is to provide a responsive computational aid and adaptive control system for effective demand management. The system consists of a short term load forecasting module, an interactive load scheduling module, an incentive based electricity cost allocation module and a power management information module.

Jan 1, 1987

By W. L. Van Heerden

In situ complete stress-strain characteristics of large coal specimens by W. L. VAN HEERDEN, B.Sc. Hons. (Pret.) (Visitor) The significance of ;n situ tests on large coal specimens is briefly reviewed. Tests aimed at obtaining complete stress-strain characteristics of large coal specimens with high width-to-height ratios are described. A formula for the relationship between strength and width-to-height ratios of coal pillars is proposed, and the influence of width to- height ratios on the deformation characteristics of pillars is discussed.

By C. R. Thomas

Although stainless steels have been used to a limited extent in the South African mining industry, the metallurgical development of 3CRI2 has presented materials engineers with a viable alternative for certain materials-handling applications. The various types of wear involved in these operations are described, and an explanation is given of how 3CRI2 is able to offer advantages, particularly in wet sliding applications. Certain applications result in various types of abrasive wear, and the performance of 3CRI2 in these areas is described.

Jan 1, 1981

The support of stopes by means of yielding timber props, with or without hydraulic props, is common in the mining industry. This paper discusses the ability of these support systems to absorb energy during a rockburst, and further investigates their capability to withstand a range of ground velocities. It is found that the rate of stope closure prior to a rockburst strongly influences the behaviour of these support systems during the rockburst. It is recommended that hydraulic props be used in conjunction with yielding timber props in these conditions, and that yielding timber props with an increased yield range are desirable.

Jan 1, 1991

Contribution by W.D. Ortlepp? The authors are to be commended for publishing their interesting view of an aspect of deep-level mining technology that is becoming increasingly topical and vitally important. This is the second paper in the journal within four months to deal with the crucial needs of highly stressed tunnel construction, the other being the paper on the design and testing of rockburst support in the February 1994 issue. Both papers re-examine important innovative ideas that are more than a quarter of a century old, but that have not yet been implemented by the industry. It is to be hoped that they will now, taken together, serve as a new starting point for a definitive examination of what constitutes proper tunnel-support design. There can be no question that the need to develop a design approach that will solve the problems of tunnelling at depths of 4000 m or more has now become crucial. Contribution by A.M.J. Vervoort* Although the overall paper is very interesting and the future research (comparison between numerical simulations and underground measurements) will be very challenging, I would like to make some remarks regarding the set-up of the numerical model and the interpretation of the elastic results.

Jan 1, 1995

By D. Savile Davis

D. Savile Davis* (Member): The members of the Chamber of Mines Research Laboratories, headed by Dr Cook, indeed deserve all the plaudits that have been given for the original conception of the rock-cutter, and for the research work that has gone into designing the equipment now being tested. Underground trials with the rock-cutting machines at the Doornfontein Gold Mining Company Limited have been encouraging to the extent that 29 square fathoms of rock have been cut in the past three months with two modified prototype machines. Both the hangingwalI condition of the stope and the control of stoping width have been excellent. So far, however, the rate of production has been too slow and does not compare with conventional stoping methods, due firstly to the time-consuming operation of moving the machine forward and resetting it in its next cutting section and secondly to mechanical defects. Although great strides have been made in improving the tungsten carbide cutting tool, further progress is dependent upon engineering development in the design of a more reliable and versatile machine within economic limits. Commenting briefly on the experiments that have been carried out on the Gold Fields mines, the rock-cutter, when used at the Luipaards Vlei mine, some 600 ft below surface, cut very nearly perfect slots above and below the reef on a stope face but was unable to cut slots in the reef itself. At the Doornfontein mine, however, where the tests are currently being carried out at a depth of 8,000 ft below surface and where there is a much greater pressure acting on the rock face, vertical fracture planes can be clearly seen in the hangingwall running parallel to the face. Owing to the presence of these fracture planes it has been found impossible to cut slots of any depth and the action of the machine is more one of spalling than of cutting, resulting in slabs of combined reef and waste falling from the face as the cutting tool advances. This is accentuated by the existence of a well-defined hangingwall parting plane. Most of the slabbing takes place from the slot cut below the reef to the hangingwalI of the stope. Since waste sorting in narrow conditions and poor lighting is not an efficient operation, the reef together with a proportion of waste rock, has to be removed from the stope. The ripping action of the machine as opposed to slot cutting under these particular conditions may not be a great disadvantage, as the volume of waste which can be packed depends on the ratio of reef width to stope width and with a narrow reef body some waste has to be removed to the surface. In these circumstances mining at depth with this type of machine should not be viewed as selective mining but more correctly mining without explosives. Another type of rock-cutter is being tested by the Gold Fields Group, consisting of a diamond studded rotating disc, which has, to date, cut slots 10 ft in length and averaging 7 1/2 in. in depth. It is, however, too early to comment on the practicability and economics of such a cutter. The great interest that is at present being shown in breaking rock without the use of explosives warrants comment on the Robins raise-borer, recently introduced into South Africa, and used for the first time with great success at the Doornfontein mine.

By M. W. Grodner, J. Maaren, G. Guler, J. K. Schweitzer

The selection of the most suitable mechanized mining strategy has to consider the geotechnical environment in which it will be operating. A mechanized mining method or machine is designed to a given set of specifications to work within an environment. The geological conditions that define this environment are fixed—detailed information of these conditions for design specifications is thus critical. Two major classes of geotechnical parameters are defined—critical and design. The critical controlling factors are a result of mineral composition, size, shape, abundance, assemblage and associated texture, as well as discontinuity type and orientation. Design parameters are specific to each deposit, and their nature cannot be broadly described, as with the critical factors. It is shown that for major deposits in South Africa, namely the Witwatersrand Basin (gold), the Bushveld Igneous Complex (PGEs) and the Karoo Coalfields that by incorporating geological and geotechnical information that appropriate mechanized mining methods can be deduced, and that the performance and design parameters of specific technologies can be determined

Sep 1, 2001

Each year the South African Institute of Mining and Metallurgy offers a prize (or prizes should the entries warrant it) of up to RlOO for the best paper or dissertation on a topic appropriate to the interests of the Institute. The competition is open to all Student Members of the Institute. A Student Member who is in fulltime study at a university may submit the dissertation or thesis he has to write in part fulfilment of his university degree, provided that it is presented in a manner and on a topic suitable for publication in the journal. Entries for 1976 should reach the Institute by 31st December, 1976.

Jan 10, 1976

By M. B. Dunn

Terminals form part of the transportation chain from producer to consumer in the world-wide conveyance of bulk commodities. As such, they are a vital link in providing a buffer between widely differing transporation modes. It is essential in the conceptual design of such terminals that an overall view of the entire system of which they form a part is taken. Only in this way can it be ensured that the system will operate smoothly and without disruption, for in the end such disruptions can have dramatic repercussions, both on the cost of the commodity in the market place and on production. In this respect, computer simulation is a useful tool in arriving at the optimum design for the system. The Richards Bay Coal Terminal provides a good example of such an approach. Commissioned in 1976 to handle 12 Mt per annum, it is now handling 24 Mt per annum, with plans for further expansion to 44 Mt per annum in the future.

Jan 1, 1980

By M. D. G. Salamon

If a transition from one equilibrium state to another occurs during the course of mining, energy transfer takes place in the rock mass, which is assumed to be an elastic continuum. The energy components are defined as follows: the work done by external and body forces, W; the increase in stored energy in the mass, Uc; the strain energy in the rock mined during the transition, Urn; the work done on mine support or backfill, Ws; and the released energy, Wr. The energy balance is defined as (W + Urn) - (Uc + Ws) = Wr> 0, where the first set of components in parentheses represents the sources of energy, while that of the second corresponds to the known modes of energy expenditure and the component on the right is the unaccounted-for energy surplus, which must be released and dissipated in some form. The inequality Wr ~ Urn> 0 applies. Expressions for the energy components are derived first for the general case and then for the 'slit' modal used to simulate tabular excavations. Through specific examples, the importance of the progressive nature of mining is emphasized. The size of the steps used to enlarge the excavations appears to play a significant role in the mode of energy transfer. This observation forms the basis of the second paper in this series of two papers.

Jan 1, 1984

By G. J. de Korte

South Africa is reliant on coal for the generation of almost all the electricity used in the country, and several large industrial concerns such as Sasol are also coal based. Research relating to the mining, beneficiation and utilization of coal is important in order to ensure the optimal exploitation and use of coal within the country. The Fuel Research Institute (FRI) of South Africa was established in 1930 to investigate all aspects of coal beneficiation and utilization in South Africa. The FRI went on to conduct world-class research and in 1957 a pilot coal preparation plant was constructed in Pretoria to enable large-scale practical experimentation. The pilot plant played a pivotal role in the establishment of South Africa?s low ash coal export project. Political and economic factors contributed to the eventual closure of the FRI and South Africa experienced a period of about 10 years between 1990 and 1999 during which very little public coal preparation research was done. This changed for the better towards the end of 1999 when Coaltech 2020, a collaborative research program was established. Participants included the CSIR, universities, the government and the major coal producers. Coal preparation research conducted under Coaltech thus far include dewatering and drying of fine coal, size classification of ultra-fine coal and dense-medium fine coal beneficiation. Currently, the Coaltech focus is on the beneficiation of low-grade coal reserves and is investigating existing as well as new techniques that can be utilized to provide cost-effective beneficiation of low-grade raw coals and reject coals.

Jan 1, 2010

By Z. Nzimande

The Constitution of the Republic of South Africa advocates the importance of sustainable economic development and justifiable environmental consciousness by business. The government needs to ensure that every citizen of the Republic has access to an environment that is protected, pollution free, and sustainable by enacting certain regulations. However, there are more than 5 700 derelict and unrehabilitated mines of all types in South Africa. Former asbestos operations were among the first to be targeted for clean-up under the programme instituted by the Department of Mineral Resources (DMR), owing to the proven direct impact of asbestos pollution on health. This paper seeks to investigate the challenges faced by the coal sector as far as mine rehabilitation and closure is concerned. For the purpose of this paper rehabilitation is defined as per the Chamber of Mines Rehabilitation Guidelines publication, which defines rehabilitation as putting the land impacted by mining activities back to a sustainable and usable condition. Some of the current rehabilitation challenges are technical skills (know-how), leadership focus, poor planning, cost saving initiatives, and the government's lack of capacity to enforcement rehabilitation requirements. It is imperative that mining companies identify rehabilitation as a critical strategic pillar that directly influences license to operate. The case study evidence indicates that relevant policies, appointment of accountable people, sufficient leadership support, and the correct choice of rehabilitation equipment can assist to improve the rehabilitation and land management challenge.

Jan 1, 2012

By Peter N. Calder, Alan Bauer

The complexity of modem open pit load-haul-dump systems is described, and the need for realistic working models is pointed out. Both standard and probabilistic simulation procedures are discussed, probabilistic simulation being indicated as the more powerful and practical technique. Acquisition of the necessary pit operating data required for simulator construction and general modelling procedures are described. Finally, results from a typical open pit simulator are used to indicate the scope of the technique.

Jan 1, 2014

By S. Selmer-Olsen

New trends and developments in the production of ferro-silicon, ferro-manganese and ferro-chrome alloys are discussed, with emphasis on the general trend to the adoption of large production units. Problems which arise, both of a metallurgical and an electrical nature, due to the use of large electric furnaces, are outlined with specific reference to the limitations imposed by the power carrying capacity of Soderberg electrodes, the furnace resistance and the furnace reactance. The implications of combining high resistance within the furnace with good metallurgical operating conditions are illustrated by considering the production of ferro-silicon and ferro-manganese. The possibility of replacing electric furnaces used for ferro-manganese production, by large low shaft blast furnaces using oxygen enriched blast, is mentioned. The continued use of small electric arc furnaces for ferro-chrome production is also mentioned, and is ascribed to lack of ore suitable for treatment in large furnaces. Agglomeration of chromite ores appears to be a possible answer to this problem.

Nowadays, fully encapsulated rockbolts have become a key element in the design of ground control systems. The main reason is that they offer high axial resistance to bed separation. In this research, the load transfer capacity of a fully grouted bolt is evaluated analytically in an elastoplastic rock mass condition. The research considered the effect of bolt end-plate on load transfer capacity. Bolt and surrounding materials were assumed to be elastic and elastoplastic materials respectively. The load transfer mechanism of a fully grouted bolt is a function of parameters such as bolt length, shear stiffness of interfaces, in situ stress, presence of face-plate and distance along the bolt. These factors were analytically evaluated. Finally, the load along the bolt was predicted in different surrounding rock mass characteristics.

Jan 1, 2011

By M. H. Marsden, R. A. Laybourne, J. D. Flint

Operations of the strip mine at Arnot Colliery are described, and the improved volumetric extraction of the in situ coal reserves that has been obtained by the application of strip-mining techniques is highlighted. An account is given of the major problems encountered during the early stages of the operation with particular reference to overburden removal. coal and parting handling, and transportation. The techniques used in dealing with the problems and the current degree of success in overcoming them are outlined.

Jan 1, 1980

By D. Vogt

South African underground hard rock mines are typically managed using measurements made daily, weekly or even monthly of key parameters such as face advance, readiness to blast, blast success, temperature or dust levels. Safety and health can be greatly improved if a real-time measurement system can inform decision making. To enable this vision of widespread sensing, communication and decision support, CSIR has developed an open standard architecture for communication of sensor data, and a reference implementation using that standard. The standard is called AziSA, which means ?to inform? in isiZulu. AziSA provides an architecture that allows for connection of any type of sensor and that is particularly suited to wireless sensing. On the safety side, the CSIR is developing a suite of sensors specifically around the risk of rockfalls. Sensors such as an electronic replacement for the barring tool, or a thermal sensor that can detect loose rock, can already be used to identify potential hazards in the hangingwall. When these sensors are combined with location and time information in a single database, it becomes possible to build maps of risk and to extrapolate risk into unmined areas. It is also easy to confirm that routine safety procedures like barring are actually taking place. In the future, it is proposed that entry inspections will be made using remote techniques that will not place an individual miner at risk. While miners will still be required to bar or place support, they will do so with a clear idea of which portions of the hangingwall are safe, and which present risk. On the health side, if a network such as AziSA is deployed in the stope, it becomes much easier to monitor the condition of individual miners. The work strain experienced by miners can be monitored through heart-rate sensors, and their core body temperature can be monitored using various novel techniques discussed in the paper. Additional sensors can be added to quantify worker exposure to hazards such as noise or dust. Individual sensors allow for people who are at an unacceptably high risk of developing heat disorders to be treated timeously, and they also allow for team management based on objective measures. Over a longer period, position sensing and environment monitors, or personal dosimetry, provide a powerful management tool to prevent workers from being overexposed to hazards, and to confirm that management instructions are being followed. Cost-effective sensing in the stope is a major challenge, but one that can be overcome through technology like that used in AziSA. Sensing provides opportunities both to make immediate interventions when workers are exposed to unacceptable risk, and to manage the long-term exposure of workers to hazard.

Jan 1, 2010