Search Documents

By A. J. Jager, G. R. Adams

The pattern of mining-induced fractures ahead of stope faces in deep-level gold mines, as revealed by petroscopic observations, is described. It is shown that there are zones of fractured and unfractured rock ahead of the face, which are about I m wide and continue as discrete entities for at least 12 m parallel to the face and at least 5 m vertically. These zones do not form continuously as mining progresses, but develop from time to time, leaving a solid zone between the fractured zones. The maximum depth of fracturing ahead of the face depends on the rate of energy release.

Jan 1, 1980

By R. P. King

The flotation behaviour of phoscorite from the Phosphate Development Corporation was measured in a pilot plant, the flotation cells in the plant being varied in configuration so as to operate with or without circulating loads. The ore was floated in a batch cell so that the parameters for a kinetic model could be estimated, and these parameters were then used in a flotation-plant simulator, which is based on the kinetic model, in the prediction of the performance of a pilot flotation plant operating on phoscorite. The simulator predictions compare well with the measured performance of the ore in the pilot plant, but the comparison shows that the kinetic model is not completely adequate for the prediction of performance in continuous flotation plants. The model is weakest in its ability to model the behaviour of the froth phase. The flotation behaviour of the ore could be adequately described when it was assumed that the apatite and gangue each consist of floatable and unfloatable components. The effect of particle size on the specific flotation-rate constant of apatite was found to have a maximum at 85 µm and to fall to zero at 400 µm that for the gangue had a maximum at 50 µm and was zero at 350 µm.

Jan 1, 1978

By W. J. Kempson

As a result of the rising electrical energy costs in South Africa, a method was sought to reduce the overall electrical consumption of typical shaft systems. A typical shaft configuration was analysed and the primary energy consumers were identified. The ventilation fans for this system were found to consume 15% of the total energy of the shaft system. It was calculated that more than 50% of this energy is consumed by the shaft itself, more specifically, by the pressure losses that occur in the shaft as the ventilation air passes through it. In order to ensure that the theory being used for the evaluation of these shaft systems is accurate, a total of five shafts were instrumented and the actual pressure losses over the shafts plotted against time. These shafts were then analysed from a theoretical perspective. Finally, in order to ensure a thorough understanding of the behaviour of the ventilation air in shaft systems, the systems were simulated using computational fluid dynamics (CFD) techniques. There were significant discrepancies between the theoretical analysis and the CFD simulation during the initial comparisons. This discrepancy lessened as the complexity of the CFD models increased, until when the complete shaft was modelled using the full bunton sets, the pipes, and the flanges, the difference between the theoretical evaluation and the CFD simulation was small. This result demonstrates that the theory is insufficient and that the interrelated effect of the buntons and fittings has not been fully appreciated by current theory. The final phase of the work presented here was to evaluate the costeffectiveness of using different bunton shapes and shaft configurations. It is shown that the increase in the pressure losses and therefore the direct operating costs of the shaft can vary by as much as 80%, depending on the bunton configuration chosen. The placement of the piping in the shaft can increase the pressure losses, and therefore the direct operating costs of the shaft, by as much as 12%, depending on the placement of the piping in the shaft; this effect includes the use of flanges. The use of fairings on a large cage can reduce the resistance that the cage offers to the ventilation flow by as much as 30%. This, however, does not translate into a direct saving because as the cage moves through the shaft, the overall effect is transitory. These savings can be significant when the items highlighted in this work are applied correctly. Keywords shaft design, ventilation, energy consumption, modelling, CFD.

Dec 1, 2013

NIM reports Report No. 1615 Fluorspar pellets. A survey of the world market and an assessment of future South African production. Report No. 1621 Correction for matrix effects in the analysis of solutions by X-ray-fiuorescence spectrometry. Notices Questionnaire on Technicians The Department of National Education's committee of enquiry into the education, training, utilization, and status of engineering technicians in the Republic of South Africa was established as a result of Resolution 6.3 taken at the Sixth Conference on Engineering Education: The Education and Training of Engineering Technicians. Vraelys oor Tegnici Die Departement van Nasionale Opvoeding se komitee wat ondersoek instel na die opleiding, gebruik en status van ingenieurstegnici in die Republiek van Suid-Afrika is gestig as gevolg van Besluit 6.3 wat geneem is tydens die Sesde Konferensie oor Ingenieursopleiding: Die Opleiding van Ingenieurstegnici. Competition for Student Members of the South African Institute of Mining and Metallurgy Each year the Institute offers a prize (or prizes should the entries warrant it) of up to R100 for the best paper or dissertation on a topic appropriate to the interests of the Institute. The competition is open to all Student Members of the Institute.

Jan 8, 1974

Contribution by J.S. Kuijpers* Kirsten's paper discusses the potential for seismic activity on faults in relation to depth, span, stope support, and discontinuity strength, and puts forward some explicit conclusions. Quoting from the author, the main conclusions are as follows, together with my comments. Author's reply The author gratefully acknowledges the contribution to his paper. It provides further elucidation to the very complex problem of quantifying the effects of mining-induced seismicity. The mechanical behaviour of rock under seismic excitation has been sadly neglected over the past twenty years, during which attention was almost exclusively focused on the study of the spatial location of seismic events. It is to be lamented that, on the eve of South Africa's movement to significantly greater depths of mining, so little quantities information is known about the mechanical effects of seismicity. It is a challenge at this stage to make up for this lapse in knowledge in the shortest possible time.

Jan 1, 1994

The FSPE Award for Services to the Engineering Profession was awarded to Or Francis George Hill at a ceremony held in January of this year by the Federation of Societies of Professional Engineers. The following is an abridged version of the citation made by Professor A.N. Brown, President of FSPE, and of Or Hill?s reply. Achievements. It is indeed fitting that such a distinguished group of people have gathered on this special occasion to honour and pay tribute to Or Pinkey Hill

Jan 1, 1988

By L. E. Kun, R. O. Oelofsen, E. J. J. van Vuuren

High-rate floc-blanket clarification of gold pregnant rotary filtrate was introduced at the Vaal Reefs South gold plant of the Anglo American Corporation during February 1978. A. daily 12 000 to 15 000 t of filtrate, with an average suspended-solids concentration of 350 mg/I, is continuously clarified to a concentration of less than 2S mg/I of suspended solids in a modified plant pachuca (10 m in diameter) at throughput rates of 7,7 to 8,5 ma/m2.h by the addition of 5 g/t of ferric chloride inorganic coagulant and 0,2 g/t of Superfloc NI00 flocculant. The pachuca overflow is then clarified further in seven Stellar candle pressure filters of 54,S m2 surface area to under 5 mg/I of suspended solids. The combined clarification cost when the hopper clarifier is used in conjunction with the Stellar filters is R0,0032 per ton of liquid treated, which is approximately 60 per cent lower than the cost of Stellar filtration on its own. The savings are mainly due to the reduced use of filter pre-coat, the consumption of which has dropped by 70 per cent since the introduction of hopper clarification.

Jan 1, 1979

By Paul Fouche

The past decade has seen a tremendous revival of the base metal industry in Africa, coupled with an unprecedented increase in the prices of base metal commodities in the last couple of years. The theme of the 4th Southern African Base Metal Conference, is therefore, ?Africa?s base metals resurgence?. This conference will explore the contributions made by the mining and metallurgical disciplines to the base metals industry in Africa. It will also investigate how the base metals industry in Africa can capture the maximum potential from the increase in base metal prices through research, innovative thinking, new ways of operating and project implementation. The conference will also consider the influence of Europe?s REACH programme on the base metal industry in Southern Africa. The conference will include a technical visit to Rössing Mine (Uranium) and will be followed by technical visits to Ongopolo (copper), Skorpion Mine (zinc) and Rosh Pinah Zinc Corporation(zinc and lead). The conference, to be held in Swakopmund, Namibia, also confirms the commitment of the Southern African Institute of Mining and Metallurgy (SAIMM), to hosting a regular forum on base metals in the Southern African region. Swakopmund is an ideal conference venue for local and international mining and metallurgical professionals to be exposed to the latest advances in exploration, resource evaluation, projects and technological advances in Southern Africa?s base metal industry. The organising committee is looking forward to your participation at the conference in July 2007.

Jan 1, 2007

By D. G. Hulbert, I. K. Craig, S. P. Moult

This paper describes the application of a throughput-optimization strategy to a run-of-mine (ROM) mining circuit that is controlled by a multivariable controller. The objective of the optimization strategy is to maximize the ROM throughput at a specific product size. Results from long-term tests, which indicated how 'steady-state' optimization can be achieved, were used for the throughput optimization. This strategy increased the ROM throughput by 11,4 per cent. A mathematical relationship relating residue to grind can be used to calculate the economic benefits of stabilizing control. It was estimated that the throughput optimizer could result in an increase in gold production worth Rl,4 million per annum when waste rock is treated, and that stabilizing control could increase the treatment plants annual revenue by R150 000. If the extra milling capacity brought about by the optimizer is interpreted as a capital cost saving of 10 per cent on the price of a new mil, then a capital cost saving of RI million could result.

Jan 1, 1992

By L. M. Falcon

Cassiterite is considered to be the only economically significant tin mineral in the earth's crust, and in its purest form has a tin content of 78,6 per cent. South Africa has limited deposits of the mineral, and by its exploitation contributes about 2 per cent of the world's production. This paper gives a brief history of tin mining in South Africa, which dates back almost 3000 years. Over the intervening years, many tin-mining operations have flourished and as quickly disappeared. At present there are only three tin mines in operation, and a description is given of the methods of mining, concentrating, and smelting that are used. The properties and uses of tin are listed, together with relevant statistics.

Jan 1, 1985

By R. J. Dippenaar, W. H. Van Niekerk

The relationships between coal properties, the strength of coke, and the performance of a blast furnace were investigated by means of correlation studies, and a linear programming model was developed for the prediction of a coal blend based on these relationships. The unique feature of this approach is that it utilizes a knowledge of the minimum blast-furnace coke requirements, rather than the maximum attainable coke quality. The model predicts the least expensive coal blend that would still comply with the minimum coke-quality requirements of blast furnace. The study also confirms the existence of a relationship between the rank and caking parameters of coal, and the hot strength of coke. The effect of coke-oven operating parameters on coke quality is also discussed.

Jan 1, 1991

By M. Guarascio

Microseismic monitoring of mining areas is a developing technique, described here for the Belvedere Spinello Mine, southern Italy, where dissolution cavities in the mining area have proved problematic. The preliminary condition for locating seismic impulses has been found to be a reliable seismic ground model. Ground signals are continuously recorded by means of data from piezometric wells, for sinkhole data, and linked gephones, for microseismic data. A computer system has been implemented to collect, analyse and interpret the incoming signals consequently, identification and classification of hypocentres of activity is facilitated, with advantages in terms of safety, preventing harmful side-effects, including rock bursts, and for environmental conservation.

Jan 1, 1987

By H. A. D. Kirsten

The assessment of backfill as a support medium in gold mines has been based generally on its ability to reduce the amount of potential energy available to cause damaging rockbursts. While this regional support effect is very important, the methods of analysis commonly used to quantify it predict that, owing to the very compressible nature of the fill, the support provided in areas of small convergence will be negligible. This prediction, however, is contrary to the conditions observed in practice, namely that weak fill does provide a discernible beneficial effect. In addition to the regional support effect, several mechanisms of secondary support, particularly those applicable to areas of low convergence, are identified and discussed. These include the mechanism of deformation of the detached hangingwall beam, rotational and shear effects on bedding, joints and fractures, joint infill, the continuous support effect of the backfill under static and dynamic conditions, the preservation of the integrity of the hangingwall beam, and the potential modification of local stress fields. Confidence in the validity of some of these mechanisms is afforded by the results of theoretical investigations into the behaviour of backfill- supported stopes. The results dealt with are: ? the behaviour of the hangingwall as a beam on an elastic foundation; ? the behaviour of stope/backfill, modelling the surrounding rock as a jointed rock mass.

Jan 1, 1988

By I. H. Clark

In some mining situations, backfills are not only required to be free-standing but are also expected to provide hangingwall support. It may therefore be specified that the backfill withstand a certain calculated stress within a given time. Given the materials available, the choice of backfill composition is not always straightforward, and an approach to the evaluation of cemented tailings backfill is therefore proposed. The general use of such a method will greatly assist in both the scientific analysis of the material properties for industry-wide purposes of comparison and decision-making as regards the choice of fill.

Jan 1, 1988

By J. N. Van der Merwe

Following the Coalbrook disaster in 1960, research into coal pillar strength resulted in the adoption of the concept of a safety factor for the design of stable pillars in South African coal mining. At the time when the original statistical analysis was performed by Salamon and Munro in the early 1960s, 27 cases of failed pillar workings were considered suitable for inclusion in the database of failed pillars. Pillar failure did not stop after the introduction of the safety factor formula by Salamon and Munro (1967). In the ensuing years, pillars that were created before the application of the formula deteriorated and later failed, as did ones that were created after the introduction of the formula. This means that over time, the database of failed pillar cases increased in size, allowing ever more reliable analyses to be performed. The number of failed cases in the database had grown from the original 27 in the 1960s to 86 by 2011. All the failed cases are contained in the updated database. The database of stable pillars, which is also used in the derivation of strength formulae, has now been extended from 125 to 337 cases. The new database of intact pillar cases is more complete as it bridges the time gap between the Salamon and Munro (1967) and the Van der Merwe (2006) databases. The original requirements for inclusion into the database were satisfied in the compilation of this latest collection. The characteristics of the original database of intact pillars did not change in a meaningful way. The mining depth and pillar dimensions of the new database are largely as they were in the original database. Time-related trends with regard to pillar dimensions and depth of mining could not be found, indicating that the geometrical parameters of coal mining in South Africa have not changed meaningfully in approximately a century of mining. The characteristics of cases in the updated database of failed pillars does not differ substantially from the one published by Van der Merwe (2006). The same difference between that database and the original Salamon and Munro database, namely that the average safety factor of the failed cases had increased dramatically, from 1.0 to 1.5, is still apparent. This may be due to the inclusion of more failures from specific areas that exhibit a disproportionate number of failures at higher safety factors. These areas are the Vaal Basin, Klip River, and Free State coalfields. The new database confirms yet again that there is no correlation between the safety factors of failed pillars and their time of failure. The safety factor on its own is thus not a reliable predictor of longterm stability of pillars. Keywords coal pillar, stable pillar cases, pillar collapse, pillar data base.

Nov 1, 2013

By S. L. Crouch

A. C. Dieringt The procedure described by Professor Crouch for the modelling of mining in faulted ground allows the elastic and inelastic deformation to occur simultaneously, that is, fault slip occurs while an element is being mined. The energy release rates (ERR) shown in Crouch's Fig. 10 are apparently calculated from his equation 9 using the i total deformation Din (see the upper load line of Fig. I) Refractories The institute of 'Gesteinsh iittenkunde' of the technical university at Aachen, the Refractories Research Institute at Bonn, and the Verein Deutscher Eisenshiittenleute (VDEh) at Diisseldorf are to hold the XXII International Refractory Colloquium on 27th and 28th September, 1979, at Aachen.

Jan 1, 1979

By R. P. H. Willis

This paper describes the economics of backfilling, hydro-power, and mechanization when they are combined in an integrated stoping system. These three technologies have been shown to be viable, and the mines of the Gold Fields Group are introducing backfilling where the depths exceed approximately 2000 m below surface and in other highly stressed areas. addition, a number of mines are installing hydro-powered systems, and the first trackless stope within the Group may soon be a reality. The main emphasis in the paper is placed on the quantifiable effects of trackless stoping, including a basic risk analysis by use of a spreadsheet model. It is concluded that a substantial decrease in working costs and an increase in revenue are possible, resulting in a marked increase in working profit.

Jan 1, 1989

By F. E. Steffens

The application of kriging in assessing the area rainfall in a weather modification experiment is complicated by the presence of many zero rainfall recordings on a given day, and the fact that the variograms seem to be quite different for the rainfall on different days. Indicator variograms are shown to be directly related to two sets of conditional probabilities. Probability kriging is used in estimating the probability of rainfall amounts above any cutoff at any point

Jan 1, 1987

By A. Cáceres, L. Navarro, N. Altmann, R. Betinol

Copper concentrate is produced in Chile in the high Andes and transported to the coast for shipping through long distance pipelines. The pipeline and fittings installed have to withstand the high abrasion and corrosion environment of the copper concentrate. To protect the inside tube wall against corrosion, high density polyethylene (HDPE) liner is used. While HDPE liners can protect the steel wall against corrosion, it has also been assumed that the low surface roughness of the HDPE liner also inhibited incrustation caused by calcium carbonate and sulphate deposition. Recent events have indicated otherwise in a couple of concentrate pipelines for which BRASS has provided consultant service. This paper delivers a case study which includes (i) formation of incrustation and adhesion to HDPE liner, (ii) the detection of the incrustation through hydraulic analysis, (iii) the mechanism of removal of incrustation, and (iv) the catastrophic effects of their presence in an emergency situation.

Jan 1, 2007

By Neal Harries

The monitoring of rock slopes is a common procedure in the management of hazards associated with slope instability. Slope stability radar has become widely accepted as the state-of-the-art method for management of hazards associated with unstable slopes in open pit mines. This is confirmed by the rapid adoption of the technology since inception in mid 2003, with over 70 GroundProbe slope stability radars now in use at open pit operations throughout the World. The use of a monitoring system such as slope radar to identify slope hazards is only part of the solution to minimise the consequences associated with slope instability. The presence of the hazard must also be effectively communicated to the mine personnel, so that the correct response to the hazard can be enacted, and the risk mitigated to an acceptable level. In some surface mines, due to the geotechnical characteristics of the rock mass, hazards can develop rapidly; with slopes progressing from stability to ultimate collapse in just hours. In these situations, it is vital that efficient systems are developed to evacuate the area of the pit affected. Such a system has been developed by GroundProbe in South Africa, with the vital driving force for the project being provided by the Anglo Platinum Mogalakwena mine operation based at Mokopane. The mine based development of the system was perceived as an essential aspect in the development of the successful system. From an early stage, the mine provided essential input on both hardware and software developments to allow the system to be rapidly integrated into the mining operation. This paper describes the pit evacuation alarm system that was developed and discussed the benefits obtained from a mine based development program.

Jan 1, 2008