Search Documents

By W. A. Lenhardt

During the past five years, several research projects on the causes of mining induced seismicity have been carried out by the Rockburst Research Department at Western Deep levels Limited. This paper summarizes the results of these investigations. Several types of mining-induced seismic events are addressed, and models of their mechanisms are presented. It is shown that most of the seismicity results from mining in geologically disturbed areas, and ways and means are discussed to reduce the seismic potential. Stabilizing pillars, for instance, have been introduced to reduce stresses at the stope face and to alleviate the facebursting problem. Facebursts still occur in areas of very low stresses, and pillars became the source of very large seismic events (M >3). At this stage, the understanding gained of pillar-associated events allows a review of current mining practices. Further, it makes possible an examination of the efficiency of measures to alleviate the effects of various seismically prone situations.

Jan 1, 1992

NEW BOOKLET FOR POTENTIAL ENGINEERS A new booklet "Professional Careers in Engineering" for issue to high school students who are considering engineering as a profession has been prepared for general distribution. The booklet is intended to help high school students to decide whether a career as a professional engineer would appeal to them, and to tell them how to set about becoming a professional engineer. Copies of the booklet may be obtained free of charge by writing to: The Federation of Societies of Professional Engineers, P.O. Box 5907, Johannesburg.

By M. L. Young, J. B. See

Effective thermal conductivities of packed beds of chromite ores by M. L. YOUNG, B.Se. (Rand), M.Sc. (Rand) (Visitor) and J. B. SEE, B.Sc. (Hons), Ph.D. (New South Wales), M.I.M., M.I.M.M. (Member) The effective thermal conductivities in stagnant air of packed beds of fines, lumps, and indurated and pre-reduced pellets of two chromite ores with different chromium-to-iron ratios were determined in the temperature range 300 to I 100°C by the heat-sink technique. Packed beds of fines, whether of the size fraction between 20 and 65 mesh, between 65 and 100 mesh, or between 100 and 150 mesh, were found to have the same values of effective thermal conductivity. For one ore, the effective thermal conductivities of packed beds of fines between 20 and 48 mesh at tem peratures above 600"C were higher than those for finer particles. This difference is explained as being due to the increase in importance of radiation heat transfer, but no definite conclusions are reached about the relative contributions of conduction and radiation heat transfer to the effective thermal conductivities of packed beds of fines between 20 and 48 mesh. Two published models were used for the theoretical prediction of values for thermal conductivities of the indurated and pre-reduced pellets as well as of lump ore. The experimental and theoretical results were in good agreement in view of the uncertainties in the assumed values of emissivity and thermal conductivity of the chromite ore.

Jan 12, 1976

By D. T. Williamson, B. P. Gilbertson

Satellite observation of mine-dump vegetation by B. P. GILBERTSON, M.Sc. (Phys.) (Visitor) and D. T. WILLlAMSON, B.A., LLB., B.A. Hons. (Visitor) NASA's first Earth Resources Technology Satellite (ERTS-I) was launched on 23rd July, 1972, and has subsequently gathered multispectral imagery of most of Southern Africa from an orbital altitude of 900 km. Images of the Witwaters rand area have been studied in an attempt to differentiate between mine dumps having varying degrees of vegetative cover. At this stage it is clear that the various mine dumps can be located and identified, and differences in vegetative cover can be seen and measured. Patterns of vegetative growth, some characteristic to particular dumps, can also be seen.

Jan 2, 1974

By S. R. Stadler

Koffiefontein Mine commissioned a distributed antenna system as an underground communication backbone for the DISPATCH® production management system during September1999. STAS Ltd, the supplier of the Distributed Antenna System developed the System for an Integrated and Automated Mine (SIAM). This communication system, in conjunction with DISPATCH®, fulfils Koffiefontein Mine’s present and future requirements for accurate draw control, increasing productivity and improving working conditions. The DAS as SIAMnet communication network was selected by the mine, because of its superior data transmission rate of up to 1.5Mbps at 860MHz, video and Ethernet transmission facilities, and future enhancement abilities. The results of the commissioning tests confirmed the quality and integrity of the data and voice communication. The initial installation enabled 9000 metres of underground production tunnels with voice communication inclusive of 3700 metres having data communication. This article discusses the requirements and selection of the telecommunication system for an underground mine. A description of the installed distributed antenna system follows with a summary of the commissioning tests. A discussion of the reliability of the components is followed by conclusions with suitable recommendations. Keywords: distributed antenna system, underground mining, telecommunication system.

Sep 1, 2001

By C. C. Johnson

In the fourteen years that Rössing Uranium Limited has been in production, the metallurgical operations and controls on the leaching plant have evolved through four basic stages. Initially, the emphasis was placed on the achievement of consistent plant operation by overcoming severe startup difficulties. The second stage involved the attainment of the design operating targets, and also the commissioning of the ferric-leaching reactors in order to achieve a ferric ion concentration of more than 3,0 g/l. Improvements in control then became the priority, with the emphasis on consistently achieving the target concentrations of ferric ions, total iron, and terminal acidity. The latest phase has concentrated on the optimization of costs by means of adjustments to the historically established operating parameters in order to achieve large savings on consumables while maintaining the leaching efficiencies. Apart from the obvious incentive of reducing costs in an inflationary economy and a depressed uranium market, impetus for this work was given by a change in the type of ore from the open pit, which has the effect of reducing the extraction efficiency while increasing the consumption of consumable materials. These problems and their solutions are discussed in detail, and the importance to cost-effective optimization of an accurate, up-to-date cost-reporting structure is stressed.

Jan 1, 1990

A 36-year-old A-S-H pump, manufactured to designs dating back to 1936, was recently presented to the Gold Mine Museum by Envirotech. The pump, a B-frame three-piece rubber-lined Hydroseal unit, was supplied by Envirotech's predecessor company, Denver Machinery, and was installed by South Roodepoort Main Reef Areas Limited on 22nd March, 1948. Metals, materials, manufacturing The 37th Annual Conference of the Australasian Institute of Metals will be held in Ballarat (Australia) from 13th to 17th May, 1985. 1985is the Sesquicentennial year of Victoria, and for the first time the historic City of Ballarat has been chosen as the venue for an Australasian Institute of Metals congress. Steel rolling Conferences on steel rolling, sponsored by The Iron and Steel Institute of Japan (ISH), and supported by iron and steel institutes in many countries of the world, have been held since 1980. The first conference was held in Tokyo in 1980, sponsored by The Iron and Steel Institute of Japan.

Jan 1, 1984

By R. C. Urquhart, D. D. Howat, R. I. L. Guthrie

Heat losses from ladles during teeming by R. C. URQUHART, M.Eng. (McGiII), Ph.D. (Visitor). R. I. L. GUTHRIE, B.Sc. (Eng.) (London), A.R.S.M., Ph.D., D.I.C. (Visitor), and D. D. HOWAT, B.Sc. (Glas.), Ph.D. (Fellow) In an investigation of the loss of temperature by liquid steel during a teeming operation, a numerical technique was used to calculate the heat flows and the rate of temperature drop over the entire teeming operation. The calculations show that, before teeming, approximately 50 per cent of the heat loss is into the ladle wall at the level of the metal. As teeming progresses, the amount of heat lost by radiation to the wall above the metalline increases. The effect of variables, such as initial metal temperature, the preheat of the ladle and ladle cover, and delays, on the rate of temperature loss by the metal were determined.

Jan 11, 1973

By S R Grano

A fundamental model, which considers the subprocesses of particle collection by bubbles in flotation, is applied to two comprehensive flotation surveys in the rougher stages of C3 concentrator, PT Freeport Indonesia. The flotation surveys focused on the collection of: ? cell-by-cell and size-by-size metallurgical, ? cell hydrodynamic, and ? pulp and surface chemistry information. The two surveys were conducted at significantly different feed tonnages, giving rise to significantly different feed particle size distributions, pulp densities and mean pulp residence times. A series of model simulations are performed with the aim of quantifying changes in copper recovery, on both a size-by-size and unsized basis, with changes in values of the hydrodynamic parameters and hydrophobicity of the copper sulfide mineral. This was carried out in an effort to identify the most promising route to increase overall copper recovery in roughing. It was found that by increasing the hydrophobicity of the copper sulfide mineral surfaces it became possible to optimise cell hydrodynamics, which targeted increased fine (-12 µm) copper sulfide mineral recovery but without adversely affecting coarse (+150 µm) copper sulfide mineral recovery.

Jan 1, 2007

By G. Pienaar

The South African Institute of Mining and Metallurgy held a Colloquium on High-strength Low-alloy Steels on 27th October, 1983, at the Vaal Triangle Technikon, Vanderbijlpark. The Colloquium was attended by some 170 delegates.

Jan 1, 1984

By M. Splaine, W. Davidson, D. C. Atkinson

Since 1964, Nchanga Consolidated Copper Mines, Ltd., has been developing and using production scheduling methods for optimizing its metallurgical operations in the short term (up to one year). Medium-range metallurgical planning has been possible only by successive evaluations of a single-year LP. A modified version of Rosenbrock's direct search technique has now been developed to allow multi-year optimization of both mining and metallurgy for medium-range planning. The modifications to the search technique have produced a marked increase in computational efficiency for this heavily constrained problem in many variables and the system is a usable planning tool, given a reasonably powerful computer. The plans are 'optimum' in the sense that they yield the maximum present value of the operations. Each of the resulting five-yearly mine plans forms the basis for further detailed metallurgical evaluation by the established production scheduling system.

By R. Van Rijswick

Crankshaft driven piston and piston diaphragm pumps inherently generate a varying flow each crankshaft revolution. Depending on the system connected, this flow variation results in a pressure pulsation. This pressure pulsation may, depending on the structural design, result in structural vibrations. In order to limit the level of pressure pulsations, volume absorbing devices, mostly gas filled vessels, are used. The standard selection of these so-called dampeners is based on the flow variation of the pump but does not incorporate the interaction with the connected system. The paper discusses the application of a pulsation analysis tool developed by WEIR Minerals Netherlands, manufacturer of GEHO positive displacement slurry pumps. The paper first discusses the basics of pressure pulsation analysis, such as flow variation generated by crankshaft driven pumps, and hydraulic effects such as capacitance, inductance and resistance and their influence on the hydraulic response of a system. Furthermore, the relation between pressure pulsations and structural vibrations, known as fluid structure interaction, will be discussed. Additionally, the capabilities of the pump pulsation analysis tool are presented, illustrated by examples of simulation results and experimental verification.

Jan 1, 2007

By K. R. Vost

Variation in air temperature in a cross-section of an underground airway by K. R. VOST, B.Sc. (Glas.), M.Sc. (N.S.W.) (Visitor) Measurements of air temperatures in underground airways are normally made at only one point in a cross-section, and the air tem peratures at other points in the cross-section are assumed not to differ significantly from this. This paper discusses measurements made at a number of points in fifty crosssections in airways with different air velocities and wetness of floor. These measurements show that significant variations of air temperature can occur in a given cross-section at a given time. The effects of such variations on the accuracy of measurement of rises in air temperature as air passes along an airway are discussed. The importance of considering experimental error in the measured rises in air temperature when attempting to validate theoretical and empirical methods of predicting such rises is also discussed.

Jan 7, 1976

By N. B. Strydom

The data on heat stroke cases reported during the past five years were examined to determine the influence of age on the incidence of heat stroke. Relating the age distribution of these cases to that of the total number of Bantu mine workers showed clearly that the older men run a significantly higher risk of developing heat stroke than the younger men. Although the number of Bantu over 40 years of age in the industry is less than 10 per cent of the total they nevertheless accounted for 50 per cent of the fatal heat stroke and 25 per cent of the nonfatal heat stroke cases during the period under review. Age must, therefore, be recognised as a causal factor in heat stroke and the worker over 40 years of age should be allocated to work on surface, or in cool areas or to non-strenuous and supervisory tasks in hot areas.

By G. R. W. Walker

A unique means of obtaining sea-water by G. R. W. WALKER, Pr. Eng., B.Sc. (Hons.) (Min. Eng.) (Member) Although the mining and treatment operations at The Consolidated Diamond Mines of South West Africa, Limited, are located within an average distance of I km from the Atlantic Ocean, the supply of clear sea-water in large and continuous quantities for use in treatment plants is made difficult by siltation of water-holes and the amount of sand in suspension in the sea itself. The need for sixty million litres of sea-water per day at the new No. 2 treatment plant necessitated the construction of a system that would ensure a continuous and reliable supply. Several sea-water intake schemes were proposed. This paper outlines the need for an improved means of obtaining water and describes the construction of the scheme eventually chosen - a tunnel driven through bedrock for over 400 m beneath the Atlantic Ocean. At the end of the tunnel, two large chambers were excavated from which vertical holes were drilled to intersect the sea-bed.

Jan 5, 1976

By W. Newcomen, D. Brox

The assessment of the stability performance of open pit highwalls has traditionally been based on consideration of surface movement rates. Although generally accepted in industry, this approach presents challenges for establishing appropriate threshold values to allow for safe mining operations and does not address the issue of total strain. Surface movement monitoring data from a limited number of open pit mining operations in North and South America has been evaluated in terms of highwall strain, rock mass quality and inferred mechanism of instability. Threshold strain levels for key stages of highwall stability proposed from previous work has been reviewed and are endorsed based on evaluation of additional data. An empirical highwall strain criteria for the assessment of highwall stability performance is postulated based on relatively consistent trends in highwall strain data. L’évaluation du niveau de stabilité des hauts murs de carrières a traditionnellement été basée sur les taux de mouvements de surfaces. Bien que cette approche soit généralement acceptée à travers l’industrie, elle présente des défis pour la définition de seuils appropriés concernant la sécurité des opérations minières et n’adresse pas la notion de déformations totales. Des données de mouvements de surface provenant d’un nombre limité d’opérations minières à ciel ouvert d’Amérique du Nord et du Sud ont été évaluées en terme de déformation des hauts murs, de qualité de la masse rocheuse et des mécanismes inférés d’instabilité. Des seuils de déformation pour différentes phases clefs de stabilité de hauts murs ont été revus et sont endossés, basé sur l'évaluation de donnés additionnelles. Un critère de déformation empirique pour l’évaluation de la stabilité des hauts murs est postulé, basé sur des tendances relativement consistantes de données de déformations de hauts murs. Die Beurteilung der Stabilität von hohen Felsböschungen basiert traditionellerweise von Oberflächenbewegungen. Obwohl dieses Verfahren im Allgemeinen akzeptiert wird, stellt es jedoch gewisse Probleme für die Festlegung von Grenzwerten für die Sicherheit dar. Die totalen Dehnungen werden bei dieser Betrachtungsweise vernachlässigt. Eine beschränkte Anzahl von Oberflächenbewegungs Daten von Bergbauwerke in Nord- und Südamerika sind in Bezug auf die Dehnungen von hohen Felsböschungen, Felsqualität und davon abgeleiteten Bruchmechanismen untersucht worden. Grenzwerte für die Belastung von hohen Felsböschungen während den massgebenden Bauetappen aus bisherigen Projekten sind begutachtet und durch zusätzliche Untersuchungen bestätigt worden. Gestützt auf relativ konsitenten Trends, ist hier ein empirisches Verfahren der Dehnungen in hohen Felsböschungen zur Beurteilung der Stabilität vorgestellt.

Jan 1, 2003

By C. G. Hutson

The Zinc Corporation of South Africa (Zincor) were hosts to about forty members of the Institute at their works in Springs on Friday, 25th April, 1986. The programme, designed to give an overview of the industry and the part played by Zincor, comprised an introductory talk, a technical talk, a tour of the plant, and a luncheon. Radioactive waste in arid regions A conference on the disposal of radioactive waste in arid areas will be held in Cape Town during the period 7th to 12th September, 1986. It is recommended that engineers and scientists avail themselves of the opportunity to familiarize themselves with this relatively new multidisciplinary field of endeavor by attending the first ever conference of this nature to be held in South Africa. Iron control in hydro metallurgy The International Symposium on Iron Control in Hydrometalurgy will be held at the 16th Hydrometallurgical Meeting, from 19th to 22nd October, 1986, in Toronto, Canada.

Jan 1, 1986

By K. I. Afewu, L. C. Woollacott

The design of in-pulp adsorption vessels in the gold industry has, for the most part, been seen as a problem involving the suspension of fine particles o ore in a slurry. The need for the vessel to be designed as a mass-transfer contactor has received insufficient attention. The current series of papers addresses this need The previous paper considered the question of the scale dependence of the film transfer coefficient. This paper examines the mixing considerations that are relevant. A review of the literature and an examination of a limited set of data provide some insight into the mixing conditions needed for the dispersion of the particles of adsorbent. The mixing requirements for the suspension of the ore particles are also considered, and conclusions are drawn in regard to the design of mechanically agitated vessels for gold in-pulp adsorption circuits.

Jan 1, 1995

The wage structure of graduate White men in 1979, by Adri Kruger, Pretoria, Human Sciences Research Council, 1979.76 pp. R5,00. (Reviewer: D. G. Malan) Financial Times mining international yearbook, edited by WilIiam G. Nightingale. London, Longman, 1980. 750 pp. £24 by surface, £34 by air. (Reviewer: J. D. Austin) Techniques in mineral exploration, by J. H. Reedman. Barking (U.K.), Applied Science Publishers, 1979. 533 pp. $90. (Reviewer: D. L. Kyle) Practical geostatistics, by Isobel Clark. Barking (U.K.), Applied Science Publishers, 1979. 129 pp. £13,75. (Reviewer: D. G. Krige) Uranium: The balance of supply and demand 1978- 1990, by the Uranium Institute. London, Mining Journal Books, 1979. 61 pp. £8,50 by surface,,£9,25 by airmail. (Reviewer: D. J. Crowe) Wear and abrasion in industry The South African Institute of Mining and Metallurgy and the Institution of Metallurgists (South African Branch) is to hold a colloquium on the topic of wear and abrasion of metals in February 1981. Steel rolling The International Conference on Steel Rolling sponsored by The Iron and Steel Institute of Japan will be held in Tokyo, Japan, from 29th September to 4th October, 1980.

Jan 1, 1980

By L. Hermansson

Trackless mining at LKAB, Sweden by L HERMANSSON (Visitor) Because the usual means of transporting men and material to the working sites was time-wasting and uneconomical, inclined subways were installed in the Kiirunavaara Mine that permitted the access of rubber-wheeled vehicles to all underground working sites. Men and material could now be transported direct to the working site with no reloading. An increase of 8 to 12 per cent in underground productivity has been obtained by the use of this new transportation system. Rubber-wheeled vehicles are also used in development, production drilling, and loading. In December 1958, the management of the Luossavaara Mine decided to cut the costs of waste-rock haulage. The system of waste transport was the conventional one of shuttle car, rail haulage, and skip hoisting. After consideration of other methods, it was decided to re-equip the mine completely for a system of trackless transport. Results show that mining costs per ton of ore were reduced by 27 per cent, and mining costs per ton of waste were reduced by a spectacular 80 per cent. The new system has proved to be more flexible, and ore grading has been simplified since there is no longer any mixing in ore passes and chutes.