Search Documents

By R. G. Tarr

During an intense and accurate study of initiation systems used on an AngloGold mine, Mine A, poor drilling practices were revealed. Graphic results of all actual measurements taken are shown below. [ ] Accurate drilling of shot holes will determine whether a mining operation is payable or not and at what pay limit mining can take place. Losing 30 cm of a potential 120 cm-hole length will result in a number of consequences, i.e.: ?Higher stoping costs ?Drilling of one shot hole twice in every five shifts ?Increased explosive cost as a result ?Excess stress on hangingwall and footwall due to bad face shape ?Excessive blast damage before the area is worked out. No wonder we have such a high-risk operation. Drilling accuracy is crucial to the profitability on any mine as profits are directly related to the quality and utilization of the drilled shot holes.

Jan 1, 2000

By S. Sarac

In this study, a statistical model is suggested in order to determine the methane emission from a working seam. In the proposed method, methane concentrations which are systematically measured in return airway are the sample values, and the calculated statistical parameter is the upper confidence limit of the average of these values. At any given time, the probability of methane concentration in the return airflow to be lower than the calculated upper confidence limit value is 97.5%. The statistical method has been applied to the panel 206 of Armutcuk Mine, Turkish Hardcoal Enterprises. The calculated methane emission value for the considered shift was 15.18 m3/t.

Jan 1, 2003

By H. Kose

In this research, a model quarry with an annual production capacity of 1 000 000 tonnes has been studied for both pit and hillside quarry cases with constant overall slope angle and variable bench slope angle, considering road grades of 8 per cent and 10 per cent. First, technical requirements have been determined and then the effect of production parameters, such as hole diameter, type of quarrying (pit or hillside) and road grade, on the cost has been investigated to determine bench height. Based on the results, it has been concluded that hole diameter has to be kept large in both pit and hillside quarrying to reduce drilling unit costs. In addition, in order to take advantage of gravity and reduce transportation cost, it has been suggested that bench height and road grade have to be kept high and low respectively in the case of hillside quarrying (downhill transportation) while, in the case of pit quarrying (uphill transportation), bench height and road grade have to be kept low and high respectively, in order to transport the blasted material to a lower height and distance, to save energy, thus decreasing the transport cost. Keywords: Quarry, pit, hillside, road grade, bench height

Jan 1, 2005

By J. M. Lottering

Paper written on project work carried out in partial fulfilment of B Eng (Chem) degree Operational factors influencing the electrostatic separation of mineral sands were investigated in a laboratory separator. Measurements were collected online by means of an optical sensor using diffused reflectance spectroscopy to determine the mineralogical composition. The results have shown that the roll speed and potential were the dominant operating variables, collectively explaining more than 83% and 68% of the product grade and yield, respectively. In contrast, the feed rate, temperature and position of the plate did not affect separation. The effect of the ambient relative humidity, ranging from 10% to 45%, could not be assessed conclusively and at best appeared to have a weakly beneficial effect on the product grade. Keywords: process modelling, high tension roll separator, mineral sands

Jan 1, 2006

By T. Wettainen

Malmberget town is located in northern Sweden, approximately 70 km north of the Arctic Circle. Parts of the town overlie more than 20 iron orebodies, consisting mainly of magnetite with smaller quantities of haematite. The mine is operated by the mining company LKAB. Mining started in the 17th century, but not until the railway to the coastal city of Luleå was completed in 1888 did large-scale production commence. Around 1920, mining proceeded underground and today sublevel caving is the only mining method used. Sublevel caving causes subsidence of the ground surface, and buildings and residential areas have been relocated due to the mining activities for more than 50 years. The number of seismic events accompanied by strong ground vibrations is now increasing. In 2008 the mine received a permit from the Environmental Court of Sweden to increase production to 20 Mt of crude ore per year. A prerequisite for the permit was that the mine conducts a number of investigations regarding the environmental impact on the residents of Malmberget. One of these investigations concerned how seismicity will change as production increases and what measures could be taken to reduce inconvenience to the town residents. Today the mine possesses an extensive seismic monitoring system with more than 180 underground and surface geophones. For this study, eleven seismically active volumes in Malmberget mine were identified, and for each of them, a yearly future maximum magnitude interval was estimated based on the current production plan. Relationships between historical seismic events and measured ground vibrations in the town of Malmberget were established, and future ground vibrations caused by expected seismic events were estimated using a probabilistic approach. The outcome was the number of intervals of expected ground vibration per year and per monitoring point. Possible measures to reduce inconvenience for the town residents include blast restrictions, sequencing, and possibly preconditioning. The ultimate long-term solution is an almost complete relocation of Malmberget town. This process has recently been formalized and LKAB is taking an active part in realizing this goal.

Jan 1, 2014

By K. Coleman, C. Visser, N. Selby, X. W. Pan, T. Letwaba

A prototype weightometer soft sensor is under development at DebTech, De Beers in partnership with Venetia Mine. Its main function consists of an online data source; data validation; dynamic weightometer models; online detection of weightometer failure; alarming and replacing a weightometer when it fails. 31 dynamic models have been developed. All models with R2>= 85%are accepted as good models and they generally have satisfactory results with a daily error of less than 8% within 90% confidence level. By using those models, a set of soft sensors can be set up to cover all weightometers in the entire processes starting from primary crushing to the stock piles of dense medium separation (DMS). Some practical issues and concerns on model development are discussed, including data collection, data analysis, data pre-processing, variable selection, time delay, model training and model validation. When deploying the weightometer soft sensor system, the potential benefits could include: reduction in plant downtime; reduction in unplanned maintenance and even replacement of non-critical weightometers, particularly where nuclear weightometers are used. Keywords: soft sensor, weightometer, dynamic modelling, neural network modelling

Jan 1, 2003

Stope support systems, typically consisting of props and packs, are used extensively in the gold and platinum mining industry to stabilize the rock mass in the excavation vicinity and to reduce the hazard associated with rockfalls and rockbursts. The design of stope support systems was historically based predominantly on past experience and practices, and cost considerations. The recent development of a new and improved support design methodology, has led to the potential for significant increases in worker safety and support cost savings. This paper reviews some of the fundamental rock mass and support criteria that form the basis of the improved support design methodology. The considered design criteria are the height of potential fall; quasi-static stope closure rates; dynamic stope closure rates; compressive hangingwall stresses; discontinuity spacing, orientation and interface properties; effect of support length (stoping width); effect of compression rate; consistency of support performance; a real coverage; support spacing; and zone of support influence. The proposed support design methodology combines both the zone of influence and key block stability theories, resulting in optimized support systems for rockfall and rockburst conditions. The site-specific methodology consists of two stages: (i) a tributary area analysis, and (ii) a zone of support influence and a stability analysis, considering hangingwall failure due to buckling, shear and block rotation, which gives maximum safe spacing of individual support units. The methodology is suitable for designing support systems for both blocky hangingwalls and hangingwalls fragmented by face-parallel extension and shear fractures.

Jan 1, 2001

By J. Kraemer, A. Preusse

In the federal state of North Rhine Westphalia (Germany) small and medium sized companies are beginning to extract the related gas via old shafts or boreholes and to use it as a source for the production of electricity and heat. More than 100 applications for the separate mining right on mine gas had already been filed by beginning of 2002, since mine gas is treated as a mineral resource under the Federal Mining Law. Meanwhile more than 40 mine gas concessions have been granted and first projects are being developed with encouraging results so far. To enhance the applied techniques and their efficiency Aachen University has formed a research team in this discipline. Scope and goals of this research activities are being presented in this paper. Keywords: extraction mine gas, Renewable Energy Act, Ruhr District.

Jan 1, 2003

By D. P. Venter

When Oryx Mine down-scaled in 1994, focus was placed on development, with the primary aim being the exposure and proving of ore reserves. In order to achieve this aim, development ends had to be advanced to reef at the maximum possible rate. This in turn called for support methods which could keep up with the advancing faces, taking up minimum space and time for installation, while providing on the face a real coverage and effective long-term support. In the majority of the development ends which were located in fairly competent ground, the grouted rod development support proved to be adequate until such time as secondary support in the form of meshing and lacing could be installed. The ends developing towards the eastern boundary of the mine, especially in the ?C? block, encountered extremely adverse ground conditions due to the presence of smectite zones within the footwall quartzites. Smectites are a group of montmorillonite clay materials, mainly composed of hydrous aluminosilicates. They occur as minute platy crystals in the rock mass and are especially notable for their ability to absorb liquids. Generally, the zones are found in between the bedding planes of the host rock, and may vary considerably in thickness over short distances. Wherever the smectites were exposed by the development blasting, the rockwalls weathered as the smectites absorbed water and the condition of the tunnel rockwalls deteriorated rapidly. When the smectites were left exposed and allowed to weather, it became almost impossible to install secondary permanent support such as meshing and lacing at a later stage. To minimise the exposure time and subsequent deterioration of the smectite zones, it was recommended that all development ends encountering smectites be shotcreted as soon as possible after blasting. In developing a shotcreting support methodology, both a drycreting and wetcreting system were investigated. The situation at the time ruled out the use of a wetcreting system on the basis of the extensive and costly infrastructure required, as well as its limited manoeuverability. Instead, it was decided to opt for as maller scale but more manoeuverable drycreting system. The system utilized a number of portable drycrete machines with pre-bagged cement, which could support several development ends in close proximity. Initial trials using normal 30 MPa shotcrete on 19level proved successful and the system was implemented.

Jan 1, 1998

By M. Moseki

Paper written on project work carried out in partial fulfilment of B.Sc. (Eng.) (Metallurgy of Materials) degree This paper presents the research into melting of scrap for job creation purposes in rural areas. The research was done on behalf of Mine Recycling Services (MRS), the company that will implement the project. The project involves the research into available cost effective and easy to operate technology. The paper covers the experimental and theoretical work that was conducted. The results were used to determine the best equipment and method for melting and casting brass scrap.

Jan 1, 2002

By M. van Biljon

The possible closure and subsequent flooding of South Deep Gold Mine?s neighbouring Randfontein Estates Limited No. 4 Shaft (REL 4) necessitated the construction of five concrete plugs in the connecting tunnels to prevent the ingress of groundwater into REL4 from flooding South Deep mine. Several technical investigations had been carried out before and during construction of the plugs in order to reduce the probability of groundwater flow through the boundary pillar between the two mines or through the rock mass immediately around the plugs. This paper describes the geological, hydrogeological and stability investigations carried out to evaluate the structural competence of the boundary pillar.

Jan 1, 2006

By P. Turcotte, E. Karampinos, F. Mercier-Langevin

In some underground hard-rock mines, squeezing compressive ground conditions are influenced by the presence of rock foliation and high stress. In these cases, the orientation of the foliation with respect to the drift direction has a considerable impact on the magnitude of the resulting deformation. Irrespective of the reinforcement and support strategy, keeping drives developed sub-parallel to the rock foliation operational is difficult, and often requires excessive rehabilitation during the lifetime of the excavation. This study uses field observations and convergence measurements at the LaRonde and Lapa mines of Agnico Eagle Mines Ltd to provide guidelines of the anticipated squeezing levels at these operations.

Jan 1, 2015

By M. Q. W. Jones

This paper presents a compilation of physical properties of rocks from the Bushveld Complex. The database consists of more than 900 measurements each of thermal conductivity and density. The data are well distributed from localities around the Complex and most rock types are well represented. Thermal conductivity and density are shown to vary widely in the ranges 1.8-4.2 W m-1K-1and 2600-4200 kg m-3respectively. Although only 190 heat capacity measurements are available, this parameter is quite uniform for most rock types present, 800-900 J kg-1K-1, except for chromitite, which has a lower average, 750 J kg-1K-1. Rocks encountered in deep platinum mines are particularly well characterized and this has important implications for prediction of mine refrigeration requirements. The heat flux into a semi-infinite region with properties typical of the Bushveld Complex as a function of time is substantially lower than an equivalent model for the Witwatersrand Basin.

Jan 1, 2015

By C. J. Badenhorst

The scope of this project was to research, develop and eventually produce a personal occupational hygiene and safety exposure monitor system to assist in recording and analysing various stress factors that could affect the health, wellness and safety of employees, i.e. that could result in injury or ill health of workers, create stress build-up within individual workers that could negatively affect worker alertness and safety, and, may even result in permanent disability or death. Utilized systems at the time were all reactive, whereas the DOHEMS (Proactive Digital Occupational Hygiene and Safety Exposure Monitoring) System enabled the measurement of exposure (and associated risk) in a proactive manner via real-time exposure and digitized recordings. The idea of the development was to create a unit that is so cost effective, small and light that every worker can use a system on a daily basis. The development will eventually replace current, bulky and expensive monitoring equipment. The device must be a portable battery operated device and monitor the immediate working environment by periodic sampling for vibration, noise, toxic gasses (NO/NOX/CO/VOC, etc.), body temperature and heart rate. The samples must be time and date stamped, utilizing a real-time clock (RTC) synchronized with the closest regional secondary time source and related to synchronized real-time video captured samples. These samples are then recorded onto a rugged non volatile storage device with the capacity to store a vast number of samples covering the entire working shift of eight (8) hours plus. The system has been fitted with a clear visual local alarm indication system, indicating any excessive exposures or stresses, for the worker?s supervisor to respond to. This system allows for a pro-active approach. The system is also a wireless system (to the external environment) so as to not affect the mobility of an employee and flameproof to allow for use in explosive environments. Keywords: safety, digital, exposure, monitoring, proactive.

Jan 1, 2010

By N. Reddy

The influence of local geology and rock mass characteristics on deformations during a rockburst caused by a controlled blast was studied. This was done by means of visual examination, mapping and photography both before and after the blast. We found that the ejected material was bounded mostly by fractures associated with the bow-wave fracturing and bedding surfaces and that existed prior to the blast. Most of the damage was caused by shake-out. This information is important input for the design of rockburst resistant support systems under conditions of moderate stress.

Jan 1, 2001

By H. C. de Wet

The predevelopment and preparation of a total infrastructure in a deep level mining environment, prior to the shaft system being commissioned has major advantages. This paper intends to indicate these advantages and outline an understanding of the disadvantages. These benefits can be classified in three basic groups: the financial and timing advantages, a knowledge of the ore body and the development of required technology to meet the design parameters. The required technology in many aspects was still to be developed prior to successful application. Stemming from the technological evolution are some secondary advantages which will be described in each of the groups. Safety and health considerations and some practicalities made some of the new technology redundant prior to the actual application. In each case the actual achievements and the anticipated benefits will be indicated to allow the reader to distinguish clearly between planned and actual achieved advantages.

Jan 1, 1997

By R. Falcon, P. den Hoed, A. Luckos, R. Erasmus, V. du Cann, D. Comins

Carbon as a reductant, additive or filler is an essential element in the processing of metallic ores and the manufacture of iron and steel in the metallurgical industry. In most cases, the element carbon is derived from coal and its carbon derivatives. The properties of carbon required for the different processes in each metallurgical sector vary significantly and, for this reason, matching the correct carbon product for each specific process has become an important if not vital function in all sectors of this industry. This selection process, however, has become increasingly difficult. In many cases, the substitution of new products, despite being similar in all relevant chemical specification characteristics to previous products, has resulted in different performance properties relative to that expected. Under these circumstances, the prediction of performance of unknown carbon products has become fraught with difficulties unprecedented in the past. In order to initiate an investigation into addressing these issues, a test case was selected for indepth study the results of which are reported in this paper. The case concerned the use of a specific carbon feed in a conventional submerged arc furnace which gave rise to an unprecedented amount of unreacted or only partially consumed residue trapped in the frozen slag on the refractory walls of the furnace. During the course of these investigations, different advanced analytical technologies were employed including, inter alia, Raman spectroscopy, surface dimensional tests, organic petrology and various thermal reactivity factors. All results have been integrated into a multidisciplinary assessment presented in summary in this paper. Based on the above, and previous experience, the concept of an all-embracing 3-D coal-carbon ?framework? is briefly introduced. This approach has succeeded in obtaining greater depth of knowledge and a better understanding of the issues at stake with specific reference to the organic composition, structure, texture, internal surface area and consequent reactivity of the carbon materials concerned. In consequence, it would now appear that various properties of relevance to the metallurgical industry may be predicted with greater precision than has hitherto fore been possible.

Jan 1, 2004

The paper provides a brief review of a multivariate uniform conditioning and a localized multivariate uniform conditioning (LMUC) technique, and presents a production reconciliation case study based on a porphyry copper-gold deposit in Peru. The reconciliation study compares the longterm LMUC mineral resources model (typical of new mining projects, which are invariably based on drilling data on a relatively large grid) to the corresponding production blast-hole grade control model, as well as the final plant production.

Jan 1, 2014

By B. P. Watson

Several large falls of ground occur annually in the narrow, tabular stopes mined in the Bushveld Complex. These falls comprise safety risks and cause substantial production losses and compromise efforts to increase productivity. Underground observations in conjunction with instrumentation sites were used to establish the strategic parameters required to describe the rock mass behaviour of shallow-dipping stopes on the Bushveld platinum mines. Existing rock mass rating systems were evaluated using the observations and instrumentation results. None of the current systems adequately described all the relevant geotechnical conditions. Thus a hybrid of several current systems was developed, and the proposed system is discussed in the paper. The new rock mass rating system is termed the ?New Modified Stability Graph? system and follows the method originally described by Mathews et al.1and revised by Hutchinson and Diederichs2.Changes have been made to some of the tables provided by Barton3and to the stress analysis suggested by Hutchinson and Diederichs2. In addition, the logistical regression analysis has been applied to databases, formed using the suggested analyses, for three support resistances and risk levels established.

Jan 1, 2004

In exploiting the ultra-deep, narrow reef ore bodies of the Witwatersrand, the ventilation and cooling systems within the stopes play a critical role because of high concentrations of active workers. This paper examines the heat, ventilation and cooling effects of a number of different stoping layouts for narrow reef mining in ultra-deep operations in very hot rock. The stope ventilation and cooling needs are driven primarily by the difference between the air temperature and that of the rock front being excavated. These needs depend on the face utilization, geometry, face advance (rate and direction), layout, backfill, use of water and machinery1,2,3. Detailed studies of different stoping configurations have been undertaken for mining operations extending to depths of 5000m below surface, where virgin rock temperatures approach 70°C. Extensive work has been completed with regard to evaluating ventilation and cooling requirements to maintain air reject temperatures of 28°C wet-bulb and better. This knowledge is being used to determine overall cooling requirements, reduce operational costs and maximize the efficiency of cooling systems. These issues are important when considering both the local and regional air conditioning systems and the most effective application of in-stope chilled water.

Jan 1, 2001