Search Documents

By C. Legote

"This paper investigates the conditions leading to the indefinite termination of production in four critical primary panels at an underground coal mining operation, the observed shortcomings in the mining approach, and the proposed strategy to mine through the affected panels. Initial assessment of the abandoned panel conditions indicated time-dependent strata failure,(i.e. bolted roof failure overrunning intersections), which occurred from mere minutes to up to four weeks post-production, with and without prior warning of failure. This prompted the constant re-supporting of back areas, which raised safety and productivity concerns. Investigation of the initial mining conditions revealed that the failures were due to a critical combination of factors, the chief of which was isolated horizontal stress. Other factors that were initially overlooked by the mine (i.e. influence of hydraulic stress, misinterpretation of borehole data), resulted in the conditions being described as abnormal. Remedial actions were determined, and in so doing, a new strategic approach was formulated to thoroughly address all failure concerns. The four panels were explicitly planned to serve as the main intake and return airways for the recently commissioned secondary ventilation shaft, as well as providing access to millions of tons in proven coal reserves. It is thus imperative to mine the panels. A feasibility study showed that the proposed strategy set for implementation would be financially viable. Paper written as project work carried out in partial fulfilment for BEng(Mining Engineering) degree"

Jan 1, 2015

By M. Tanaka, K. Aoki, T. Mori, H. Morioka, K. Iwano, T. Kanagawa

To estimate the detailed characteristics of the rock around the cavern during excavation, new monitoring technique for dynamic properties of the rock has been applied. In this paper, micro-seismic monitoring and AE monitoring technique are applied to the excavation of large underground rock cavern and the result was discussed to clarify the acutal behavior of EDZ around the cavern. Zur Einschätzung der Gesteinseigenschaften um die Ausschachtung herum haben die Autoren eine Technik eingesetzt, mit der die physikalischen und dynamischen Änderungen im Gestein um den Schacht während der Ausschachtung beobachtet werden. In der vorliegenden Studie wurde zur mikroseismischen Überwachung ein AE Überwachungsverfahren eingesetzt und die Autoren berichten über die Veränderungen in den Gesteinseigenschaften um die Ausschachtung herum. Dans le but d'évaluer en détail les propriétés des roches qui forment les parois des cavernes creusées, les auteurs ont utilisé une technique de mesure permettant d’observer les modifications physico-dynamiques des roches aux alentours de la caverne pendant son excavation. Dans le cadre de cet article, une technique de surveillance de l’agitation et du bruit microséismiques a été mise en œuvre et les auteurs font état de la modification des propriétés de la roche environnante.

Jan 1, 2003

To the members of The South African Institute of Mining and Metallurgy We have audited the annual financial statements set out on pages 239 to 245. These financial statements are the responsibility of the Institute?s Council. Our responsibility is to report on these financial statements. We have conducted our audit in accordance with generally accepted auditing standards. These standards require that we plan and perform the audit to obtain reasonable assurance that, in all material respects, fair presentation is achieved in the financial statements. The audit included an evaluation of the appropriateness of the accounting policies, an examination, on a test basis, of evidence that supports the amounts and disclosures included in the financial statements, an assessment of the reasonableness of significant estimates, and a consideration of the appropriateness of the overall financial statement presentation. We consider that our auditing procedures were appropriate in the circumstances to enable us to express our opinion presented here. In our opinion these financial statements fairly present the financial position of the Institute at30th June, 1997, and the results of its operations for the year then ended in conformity with generally accepted accounting practice.

Jan 1, 1997

Heavy mineral deposits are becoming more complex in terms of their compositional variation, particle mineralogy and size distributions, and present challenges for the operation of separation equipment to achieve the required grades and recoveries. Changes in equipment design and concepts potentially provide new opportunities for the beneficiation of heavy mineral sands deposits. The development of a framework for the fundamental understanding of separator performance issues is a first step to develop new machines. This paper will present a first step analysis of electro-static and magnetic separation machines with their application to real separation scenarios.

Jan 1, 2010

The 103rd Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room, Transvaal Automobile Club, 60 5th Street, Lower Houghton, Johannesburg on Wednesday, 16th August, 2000. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations. Also to recipients of awards, senior members of industry, Honorary Life Fellows, Past Presidents, our Members and other guests, among them the following: Reinie Meyer, President, The Geological Society of South Africa Dr Nielen van der Merwe, Chairman, The South African Institute of Rock Engineering Chris Fourie, President, Institute of Mine Surveyors of South Africa

Jan 1, 2000

By G. Lyman

The cross-belt sampler is a device that is very widely used even though it has not been ratified by the Standards associations. This paper is concerned with the bias testing of two cross-belt sampler designs against stopped belt samples and a cross-stream cutter at the belt end. The bias analysis is carried out using size distribution as the analyte and conventional t-testing and the Hotelling T squared test, which are compared for their effectiveness. The paper considers the issue of detectable bias and the statistical planning of bias tests.

Jan 1, 2010

To the members of The South African Institute of Mining and Metallurgy We have audited the annual financial statements set out on pages 269 to 276. These financial statements are the responsibility of the Institute?s Council. Our responsibility is to report on these financial statements. We have conducted our audit in accordance with generally accepted auditing standards. These standards require that we plan and perform the audit to obtain reasonable assurance that, in all material respects, fair presentation is achieved in the financial statements. The audit included an evaluation of the appropriateness of the accounting policies, an examination, on a test basis, of evidence that supports the amounts and disclosures included in the financial statements, an assessment of the reasonableness of significant estimates, and a consideration of the appropriateness of the overall financial statement presentation. We consider that our auditing procedures were appropriate in the circumstances to enable us to express our opinion presented here. In our opinion these financial statements fairly present the financial position of the Institute at 30th June, 1999, and the results of its operations for the year then ended in conformity with generally accepted accounting practice.

Jan 1, 1999

By P. P. Kim, M. Tangstad, T. A. Larssen

"The kinetics of MnO and SiO2 reduction in SiMn slags based on Assmang/Comilog ore and HCFeMn (highcarbon ferromanganese) slag were investigated between 1500 and 1650°C under a CO atmosphere. The results showed that charges containing HCFeMn slag had relatively faster reduction rates than those without. The difference in the driving force for MnO reduction was insignificant among the SiMn slags at 1500°C, which implies a low contribution of the driving force for reduction rate. The slag viscosities were also rather similar, around 1 poise at 1500°C, which could not explain the different reduction rates. Instead, the different charges containing various sulphur contents are believed to give rise to the varying reduction rates. The estimated activation energies for MnO reduction were around 500–920 kJ/mol for charges containing HCFeMn slag, and between 250–300 kJ/mol for those without. Based on the estimated kinetic parameters, the considered rate models were able to describe the reduction of MnO and SiO2 in SiMn slags between 1500 and 1650°C. IntroductionManganese ferroalloys such as ferromanganese (FeMn) and silicomanganese (SiMn) are important ingredients in steel production due to the beneficial effects of manganese on the physical properties of steel. Mn enhances the strength, toughness, and hardness of steel products, and both Mn and Si are used as deoxidizers to prevent the development of porous structures (International Manganese Institute, 2014; Olsen, Tangstad, and Lindstad, 2007; Subramanyam, Swansiger, and Avery, 1990; Tomota et al., 1987).The thermodynamic background of manganese ferroalloys is well established (Olsen, Tangstad and Lindstad, 2007), but kinetic information is rather scarce, especially for the SiMn process (Tranell et al., 2007; Tore-Andre Skjervheim, 1994). The absence of kinetic information makes it more difficult to understand the reduction mechanisms of MnO and SiO2. It is not clear how different raw materials affect the SiMn process. The main metal-producing reactions in the SiMn process are described by Equations [1] and [2]:"

May 1, 2019

By H. Hurkchand

Background: A cross-sectional study was conducted in November2001 to establish the prevalence rates of Human Immunodeficiency Virus (HIV) and sexually transmitted infections (STIs) (Chlamydia trachomatis and Neisseria gonorrhoea) in a coalmining town in Mpumalanga. Methods: 155 adults were recruited (79 males and 76 females), by holding community meetings, and by door-to-door recruitment. Saliva and urine specimens were collected for the analysis of HIV and STI prevalence, respectively. Results: The mean age for males was 31.35 years (min = 19 yrs and max = 50 yrs) and the mean age of the female participants was31.90 years (min = 17 yrs, max = 49 yrs). The prevalence of HIV was found to be 22.78% [95% CI (14.09?33.59)] in the males vs. 47.37%[95% CI (35.79?55.16)] in the females, [p = 0.001, OR = 3.05, 95%CI(1.49?6.26)]. The prevalence of C. trachomatis was 7.90% [95% CI(2.95?16.39)] in the males vs. 12.86% [95% CI (6.05?23.00)] in the females, p = 0.324. The prevalence of N. gonorrhoea was 3.79%[95% CI (0.79?1.08)] in the males vs. 9.86% [95% CI (4.06?19.26)]in the females, p = 0.137. HIV was significantly associated with C. trachomatis, [p = 0.032, OR = 3.18, 95% CI (1.04?9.72)], but was not significant when stratified by gender. HIV was not significantly associated with N. gonorrhoea (p = 0.072) but it was significantly associated when stratified by gender, p = 0.001 for females. There were no significant associations between HIV and age (p = 0.408), even upon stratification by gender. Conclusions: HIV prevalence in this community is high, and corresponds to national figures. However, the prevalence of STIs is surprisingly low as it would be expected to be high in a migrant population. Although communities are exposed to expanding peer-education activities that encourage behaviour change, the prevalence of HIV in this group. There is an urgent need for interventions designed to treat or prevent HIV infection in women generally and in women at high risk. Keywords: HIV prevalence, STI prevalence, antenatal, mining

Jan 1, 2005

By Chris Ringas

The safe operation of gas transmission pipelines is increasingly coming under the spotlight. Increasing environmental pressure is also forcing pipeline owners and operators to ensure the integrity of their pipelines. The integrity of a pipeline is usually determined using intelligent pigging, often referred to as In Line Inspection (ILI). However, in many cases, gas pipelines cannot be pigged for a variety of reasons. The National Association of Corrosion Engineers (NACE) has recently published Recommended Practice (RP) 0502, referred to as the External Corrosion Direct Assessment (ECDA) Methodology to assist pipeline owners with assessing the condition of pipelines that cannot be pigged. 2. External Corrosion Direct Assessment - NACE RP 0502 The ECDA Methodology is conducted in four phases as follows: ? Pre-Assessment ? Indirect Inspection ? Direct Examination ? Post-Assessment In the Pre-Assessment Phase, all the relevant historical and current data relating to the pipeline in question is reviewed. This covers pipeline, construction, soils/environmental, corrosion control and operational data. The aim of the Pre-Assessment Phase is to determine whether ECDA is feasible, and if so, to define the ECDA Regions and finally to select the Indirect Inspection Tools that will be used for each region. Typical overline techniques used for overline surveys include the following: Voltage gradient surveys ? DCVG or ACVG

Jan 1, 2006

The 100th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room, Transvaal Automobile Club, 60 5th Street, Lower Houghton, Johannesburg on Wednesday, 13th August, 1997. Obituaries The President announced the death, during the year, of the following members: Honorary Life Fellows and Past Presidents D.M. Jamieson, V.C. Robinson Fellows S. Goodwin, M.W. Johns Retired Fellows T.F. Muller, P.L. Nathan, N. Orsmond, R.J. Ortlepp, H.S. Sichel, K.E. Steele, W.B.L. Steuart, N.B. Vinson Member J.P. Hatfield Retired Members S.T. Baron, B.F. Pinder Retired Associate F.J.A. van Reenen In memory of the deceased and in sympathy with the bereaved, all rose and observed a moment of silence.

Jan 1, 1997

By J. Betzhold

Knowing more about an orebody makes it easier to exploit it profitably. Many orebodies are made up of different rock types, alteration zones or mineralogical ensembles: oxides versus sulphides or facies with different metallurgical properties for example. Being able to model the spatial layout of these different facies is vital to good mine planning and management. Kriging cannot be used to generate numerical models of orebodies with complex geometric patterns because it gives too smooth an image. Over-smoothing has the meaning of changing the natural selectivity. Conditional simulations are required to do this kind of model respecting the natural variability: honouring the natural selectivity, dilution and ore loss. Standard geostatistical simulations cannot duplicate many of the complex spatial relationships seen in the earth sciences, such as differently orientated facies, sets of conjugate veins or ore types where certain facies cannot touch. After a presentation of the case study, it will be shown why traditional methods for simulating indicators like the sequential indicator simulations, or the truncated gaussian method, cannot be used to simulate it. Plurigaussian simulations are then introduced and shown to be more powerful than the previous methods in their range of application. This is confirmed by the case study treated; a Chilean copper deposit, for which the plurigaussian simulations are seen to respect the different orientations of the individual facies as well as honouring the facies seen in drill holes, and respecting the proportion of each facies even if this varies in space (e.g. increases or decreases with depth). Key words: geostatistics, indicators, conditional simulation, plurigaussian method, copper variability.

Jan 1, 2000

By T. E. Oates, W. Spiteri

In 2015, after amendments to the explosives regulations, stemming became a mandatory activity for all South African mining operations. There are, however, circumstances in which it is thought stemming has an adverse impact on the blasting outcome. Some of these circumstances include blasting in hot holes, in reactive ground, or when blasting a pre-split. In order to determine when stemming is necessary, its role in the control of adverse blasting phenomena and impact on explosive performance were reviewed. Stemming was found to play a significant role in the fragmentation process and burden movement. Additionally, stemming significantly influences the control of flyrock, air-blast, and toxic fume generation. The review of the literature indicates some motivation for not using stemming for presplit, trim, hot hole, and reactive ground blasting, provided the benefits associated with not stemming the holes outweigh the risks of stemming them. Best practice for stemming from the literature indicates a stemming length of 0.7 × burden is best for larger hole diameters, and 20 to 30 × Ø for smaller hole diameters. Crushed aggregate appears to be the most effective stemming material. The South African explosives regulations pertaining to stemming were found to be consistent with those of Australia and the USA.

Aug 1, 2021

By J. M. Benson

Metal powder compaction offers unique advantages in the manufacture of net-shape components using techniques such as laser sintering, conventional press and sintering, metal injection moulding, direct rolling, direct forging, and hot isostatic pressing. If the output from the primary metal production process is in powder form, then considerable cost and energy savings can be realized by direct conversion to semi-finished or final shapes. This possibility exists for titanium and possibly also for Ta, Zr, Hf, and Nb metals. However, these attractive benefits are associated with some significant risks. The high surface-to-volume ratio of powder particles coupled with the reactive nature of these metals means that special care must be taken when handling them. Powder explosions are unfortunately still a regular occurrence internationally and these often result in serious injury and loss of life. Even seemingly 'safe' compounds such as sugar, flour, and grain can be extremely hazardous when handled or milled and dust clouds are produced. In addition, exposure to airborne particles can have adverse effects on the human body, especially when particles are inhaled on a regular basis. Furthermore, the medical consequences of these are not fully understood, especially in the case of nanoparticles. The impact is often not observed immediately and debilitating illnesses may emerge only years or decades later. As far as is known, there are no South African guidelines for handling of metal powders. This paper attempts to provide an awareness of the risks associated with metal powders (including those produced indirectly by other metalworking/finishing operations) as well as some guidelines for their safe handling, based on international best practices.

Jan 1, 2012

By M. Shapiro, L. A. le Grange, B. Henning

Effective pyrometallurgical process vessel design requires accurate assessment of the heat fluxes through the walls of the furnace. This is particularly important for freeze lining operation which is designed to protect refractory materials exposed to chemically corrosive molten contents, or facilitate high temperature operation when the refractory materials are used at conditions close to their service limits. Numerical modelling of fluid flow and heat transfer in process vessels is often used to aid in the design of process vessels. Sophisticated models are used to analyse the three dimensional flow and heat transfer predicting the effects of electrical heating, magnetic stirring, buoyancy, shear forces, various cooling effects and ultimately heat fluxes at the walls of the furnace and refractory. Traditionally these models are applied to the separate single fluid systems in a vessel such as the freeboard region including the arc, the slag region and the metal bath. Boundary conditions such as shear forces and heat fluxes between connecting regions such as the slag and metal bath are either estimated or carried over from separate solutions. Shortcomings in these traditional approaches include the estimation of sometimes critical boundary conditions leading to unreliable heat flux calculations. Also when boundary conditions are carried over between solutions, the process is difficult to set up, time-consuming and finally not fully coupled. In this paper the definition and results of a fully integrated numerical model of a complete arc furnace are presented. The most important mechanisms acting in an arc furnace were considered, including the fields of electrical potential, current, magnetism, momentum, heat transfer and radiation. Temperature dependant properties included electrical conductivity, density, viscosity, and thermal conductivity. The geometry consists of the freeboard, the arc, slag, metal baths and different refractory regions. Although the combined model of air, slag and metal would be defined as a multi-phase problem it is not solved as such. Instead the different fluids are separated by sets of special solid baffles. These baffles allow the implicit transfer of current, magnetism, heat transfer and shear forces between the different fluids and disallow mixing of the separate fluids. The strengths of the integrated model are threefold: Firstly, it provides robustness in defining the geometry and boundary conditions for the overall model. Secondly, it provides the capability to switch on and off individual mechanisms such as buoyancy, magnetic stirring and shear forces in order to observe their individual importance. Finally, it provides a useful tool in the design process through its ability to obtain results of parameter changes in short time scales.

Jan 1, 2004

By P. Fredriksson, S. Seetharaman

In the ladle refining process, the ?FeO?-content of the ladle slag is of great importance in the chemistry as well as the energetics of the process. An optimization of the process requires an accurate knowledge of the thermodynamic activities of ?FeO? in the ladle slags. Due to the discrepancies in the existing data, renewed attempts are being made at the Royal Institute of Technology to generate reliable data for binary, ternary and multi component slags containing ?FeO? at steelmaking temperatures. In order to measure the activities of ?FeO? in the slags, a gas equilibration technique was employed in the present work. The slags, kept in Pt-crucibles, were equilibrated with a CO-CO2-Ar gas mixture and quenched after equilibration. The chemical composition of the slag was analyszed. From a knowledge of the thermodynamics of Fe-Pt system, the ?FeO? activities in the slag could be evaluated. The results of the present studies, together with other literature values, were optimized in the slag software, THERMOSLAG® developed in the Royal Institute of Technology, Sweden. The results of the optimization are presented. Model calculations were performed with the KTH slag software, THERMOSLAG®, by using plant data from OVAKO Steel, Hofors, Sweden. It was found that oxygen estimations in the metal from the ?FeO? analyses of slags, obtained by conventional sampling and analysis methods, where less reliable. Estimation of the oxygen levels utilizing the sulphur partition between the slag and the metal were carried out using the THERMOSLAG® software. Reasonable estimations of the oxygen contents in the metal confirmed that this could be a very useful tool for the plant operator. Keywords: ladle, thermodynamics, slags, ?FeO?, experimentation, modelling, sulphur partition

Jan 1, 2004

By L. G. Stolarczyk, J. Duncan

"SynopsisLong before the environmental movement, coal miners were suffering from occupational diseases that became apparent in the later years of service, and especially during the retirement years. Chronic exposure to micro-fine dust in the respirable range (‘float’ dust) causes various lung diseases, referred to as coal mine dust lung disease. In the USA alone, 76 000 miners have died of coal mine dust lung disease since early legislation recognized the issue in 1969. Researchers believe that reducing float dust exposure limits alone will not reverse the increasing incidence of coal mine dust lung disease seen in the current generation of miners. Trace and radioactive metals are concentrated in the thin boundary layers of the coal seam (Roberts, 2013), and hence float dust includes silica and toxic trace metals. The production and quality of coal is also significantly impacted by the presence of these contaminants in the coal. In the combustion process, the trace metals are oxidized and become incorporated in the fly ash and flue gas. Since they are extremely water-soluble, they represent a significant danger to health and the environment. Coal preparation plants and power stations need to mitigate these contaminants as far as is practical, but the simple fact is that most contaminants should have been left un-mined.This paper describes an innovative coal-cutting solution to the longstanding technology gap in mining – the ability to measure uncut coal layer thickness to the boundary rock layer. Because of constant changes in geology, seam thickness, and seam undulation, the horizon sensor must be located in the bit-block of the rotating cutter drum of the mining machine. Contaminants in ROM coal must be minimized at the source – that is, at the rock/coal crushing cone directly under the bit-tips of the cutting drum. Bittip distances to the rock boundary layer must be automatically controlled in real time when mining in a complex and undulating coal bed. Horizon sensing (HS) technology enables the mining machine’s cutting picks to stop at a specified distance from undulating horizons of the boundary rock. The thin contaminated coal layer can be left in situ, significantly reducing the toxicity of the float dust. Preventing the metal picks from striking quartz-containing boundary rock also reduces the occurrence of methane ignitions. HS technology equipped with pick force vector sensing can allow optimization of the cutting pick lacing pattern for minimum coal and rock crushing, thereby reducing float dust. This technology may enable the mining industry to convert from automated machine control to autonomous during coal cutting and loading."

Jan 1, 2015

By D. Nag, J. Fernando

Hazelwood Power Mine is one of the largest open pit brown coal mines in Australia. The removal of overburden is the first step in coal winning operation. The primary aim of construction of overburden dump is to provide an effective stable working surface for stacker. The paper discusses site investigation techniques used to determine dump soil properties, stability analysis method using GALENA and GWEDGEM, results of stability analysis. The paper concludes with recommendation for a safe dumping strategy for level 2 stacker dumping.

Jan 1, 2003

By S. Vorberg, J. Preussner, B. Fischer, U. Glatzel, R. Völkl, M. Wenderoth

Pt-Al-X alloys have shown good mechanical properties and adequate oxidation resistance. Starting from a promising Pt-Al-Cr alloy, the influence of Ni additions was investigated. After ageing finely dispersed precipitates are observed. Nb, Ta, Ti and Re increase strength when added as partial substitute for Al. Minor additions of B increase creep resistance and rupture time remarkably, owing to strengthening of the grain boundaries. The evolution of the alloy development programme as well as selected properties of the multi-component Pt-base alloys are presented.

Jan 1, 2006

By A. Meek

This report compares the compressed air driven rocker shovel to the newly developed Warthog Non-throw development end loader. The two machines were compared on aspects such as safety, loading potential, energy efficiency and costs. The objectives of the comparison were to determine whether or not the replacement of the rocker shovel with the Warthog will be operationally and financially justifiable. The results from this study were obtained from underground observations and time studies on the machines, as well as consultations and data collection at the shaft and suppliers. This paper compares only the Warthog loader to the Trident 215 rocker shovel used at Anglo Platinum?s Brakspruit shaft and does not compare the other models of rocker shovels, which are fundamentally the same but will have different loading potentials and specifications. Cleaning times for the rocker shovel are based on underground observations at Brakspruit shaft. These times can be influenced by factors such as blasting practices, compressed air pressure and operator experience and skill. For this reason the times will most likely vary at different shafts. The Warthog cleaning times are based on manufacturer specifications and results from trial stages and therefore further work is required to confirm cleaning times achieved.

Jan 1, 2009