Search Documents

By E. P. Gustafson

Demand by precious metals explorationists for cost effective means to target subsurface geologic structures worthy of evaluation by means of drilling has led to the use of the predictor-correlator technique. To locate polarizable targets, the predictor-a localized inhomogeneity in electrical properties-is placed at various locations in the computer-simulated subsurface region, and correlated with the potential distribution observed in the field. The correlation coefficient obtained is assigned to the subsurface location. IP targets are extracted by calculating a second correlation section based on higher-frequency illumination and subtracting it from the first. The locations of correlation difference correspond to the locations of polarizable mineralization.

Jan 1, 1989

By Charles E. Weaver

A core from the La Camelia attapulgite mine in north Florida was studied in detail to determine the detailed vertical variability and the relations of the various parameters. The structural, textural, mineralogical and chemical data indicate there are two major depositional cycles represented within the minable interval. The sediments deposited during the two cycle differ in detail but in general are similar. The environments of deposition grade from shallow marine to lagoonal to tidal flat to marsh. The sedimentary structure (lamination, burrows, pebble conglomerate), mineralogy (attapulgite, montmorillonite, sepiolite, dolomite, calcite) chemistry (Al, Mg, Fe) are closely related to each other and their nature is determined by the depositional environments. Most of the clay minerals and carbonate minerals are authigenic and are therefore particularly sensitive to environmental differences. The variability and environmental features seen in this core are characteristic of the sediments in the general attapulgite mining area. A detailed understanding of the relationships discussed should be of value in prospecting, mining and processing.

Jan 1, 1972

By A. R. Przybylek

A fluid bed dryer has been designed for a nonconventional application to upgrade the value of fine anthracite culm and silt recovered from culm banks and anthracite tailings pond beds. This material can be seen as large spoil piles scattered throughout the anthracite coal regions of Eastern Pennsylvania. Engineering of the system commenced in December of 1986 and at this writing start-up is scheduled for late October or early November of 1987. This paper will focus on generalities concerned With system design and operation, and qualify the differences from conventional fluid bed coal drying systems.

Jan 1, 1988

By Alexander May

In its role of providing technology to promote the efficient use of minerals and mineral process waste, the U.S. Bureau of Mines has conducted research at: its Tuscaloosa Research Center to identify and develop high volume uses for phosphogypsum. Mixtures containing a maximum of 50 percent phosphogypsum, 6 to 10 percent lime, and the remainder fly ash had compressive strengths as high as 4,800 psi. The effects of the mounts of phosphogypsum, lime, and fly ash were investigated. Also, the effects of fly ash to lime ratios were studied.

Jan 1, 1983

By J. T. Sitarski, R. C. Emmett, L. W. Luinstra, R. P. Klepper

A mining operation in Zimbabwe produces a pyritic gold concentrate that requires oxidative pretreatment prior to cyanidation in order to liberate 80 percent of the gold values. Bio- oxidation offered the potential of increased gold recovery and was considered to be an economically advantageous alternative to the existing practice of roasting the concentrate. Based on bench- scale test work, a small bio-oxidation plant, capable of processing approximately 50 percent of the concentrator production, was installed at the mine to evaluate this approach. The plant included two 57 m3 bioreactors in series and the ancillary equipment needed to prepare the feed concentrate, to wash the leached residue prior to cyanidation, and to neutralize the waste liquor. The plant was operated for a year-and-a-half, and the conditions needed to achieve a 90 percent liberation of gold values were determined. A number of critical technical problems were encountered, and many were resolved on-site. Others have been addressed since the pilot plant was moth-balled in June 1988. Valuable insight was gained from the operation of the pilot plant, which has provided useful guidance for continued process and equipment improvement.

Jan 1, 1990

By K. A. Natarajan, Abha Kumari

In this paper, electroleaching and electrobioleaching of ocean manganese nodules are discussed along with the role of galvanic interactions in bioleaching. Polarization studies using a manganese nodule slurry electrode system indicated that the maximum dissolution of iron and manganese due to electrochemical reduction occurred at negative DC potentials of -600 and -1,400 mV(SCE). Electroleaching and electrobioleaching of ocean manganese nodules in the presence of Acidithiobacillus ferrooxidans and Acidithiobacillus thiooxidans at the above negative applied DC potentials resulted insignificant dissolution of copper, nickel and cobalt in IMH2S04 and in sulfuric acid solution at pH 0.5 and 2.0. Mechanisms involved in electrobioleaching of ocean manganese nodules are discussed. Galvanic leaching of ocean manganese nodules in the presence of externally added pyrite and pyrolusite for enhancement of dissolution was also studied. Various electrochemical and biochemical parameters were optimized, and the electroleaching and galvanic processes thus developed are shown to yield almost complete dissolution of all metal values. This electrobioleaching process developed in the laboratory may be cost effective, energy efficient and environmentally friendly. Keywords: Ocean manganese nodules, Electroleaching, Electrobioleaching, Galvanic interactions

Jan 1, 2003

By Chris Groccia, Damodara R. Chinnasane

Vale is in the process of resuming mining in the lower 810 ore body (810 OB) below 4130L at Copper Cliff Mine – South Side. Production in the lower 810 OB had continued until it was temporarily ceased in 2017 to allow for the execution of activities associated with Copper Cliff Mine Phase 1 project. While mining the stopes in both the lower and mid part of the 810 OB, a seismic response was experienced that resulted in rockbursts and challenging mining conditions. The majority of the rockbursts experienced in the past were associated with stopes mined in a bottom-up mining sequence under a diminishing pillar situation between 3350L and 3540L. The current mining plan is comprised of both top-down and bottom-up mining fronts using a center-out chevron sequence of long hole open stopes to manage induced stresses. Numerical modeling assessments have been carried out to forecast the response of the rock mass due to the planned mining. Seismicity and stress induced damage surrounding excavations are anticipated, and areas requiring extra attention have been identified. A tactical approach is being used to prepare the area for production, including replacement of ground support elements that are damaged or have insufficient residual capacity, and installation of dynamic support in areas anticipated to experience bulking and/or dynamic loading that would exceed the current support system’s capacity. A series of monitoring programs are being put in place to confirm current conditions, and to monitor the response of the rock mass to proactively implement ground control tactics should the need arise. This paper provides a summary of the approach used to forecast, monitor, and manage the behavior of the 810 OB rock mass response to continued mining at depth.

Apr 26, 2022

By Raoul Fernandez, Bernard Catalano, Guillaume Roux

The Thaumasia Joint-Venture, composed of Bouygues Travaux Publics, Soletanche- Bachy and Bessac, completed the construction of the underground section of line 2 of the Nice tramway, which comprised a 3.2 km twin track tunnel and four underground stations, in a particularly complex urban and geotechnical context. The density of the surface structures, as well as the presence of many historic buildings on its route made the construction of the tunnel even more sensitive, with a settlement threshold of Half an Inch. The joint venture faced a complex subsoil, varying from one extreme to another from highly plastic clay layers to fibrous peat and to cobbles with very high permeability, with artesian ground water, and with unforeseen anthropogenic obstacles in the tunnel section Due to the diversity of the problems encountered and their variability over short distances, the construction of the underground section of the Nice tramway, in its very sensitive urban context, undeniably constituted an unprecedented challenge.

Jun 13, 2023

By Frank Palkovits

All technologies move through a cycle from infancy to maturity. Thickened tailings have moved into the young adulthood phase of its development. Many mining companies like the idea of reducing their water-taking and water disposal issues. This limits the risks associated with traditional surface water-covered tailings facilities and the reduced dilution possible through underground disposal of thickened or paste tailings. Just as home theater systems advertised as ?plug and play? are rarely quite that straightforward, implementing and improving a thickened-tailings system has its challenges. However, the technology has also developed in recent years so it is more accessible. Some success factors have emerged because of the new technologies. Is thickened tailings the right solution? The first step in success with thickened tailings should be whether it is, in fact, the right solution for a particular mine. And, if so, what type of thickening is best. The answer depends on several factors, including: ? Grain size: The grain size that is optimal for maximizing mill recovery is some-times not suitable for thickening. Other mineralogical factors, such as mica content, may also influence whether the tailings are suitable. ? Water issues: Available water does not always have the purity necessary for the process. Another issue to consider is that if water is in short supply, as is increasingly often the case, thickening may be a way to reduce the need to both take and dispose of water.

Jan 1, 2008

By J. D. Miller, Jon J. Kellar

Researchers in flotation chemistry have long sought to describe collector adsorption phenomena in greater detail including kinetics, orientation and interactions between adsorbed species. Now a quantitative description can be made in-situ using FTIR internal reflection spectroscopy. Details of the adsorption process at the surface of mineral crystals, machined into internal reflection elements, can be described from first principles, provided the refractive indices, incident angle, and wavelength of light are known. Collector orientation can be established based on spectral characteristics of plane polarized and perpendicular polarized light. Examples of the use of in-situ FTIR internal reflection spectroscopy are given for the sapphire-sodium dodecyl sulfate system and for the fluorite-sodium oleate system. It is expected that quantitative in-situ analysis of collector adsorption reactions by FTIR internal reflection spectro-scopy will continue to grow in importance and will provide an important new dimension in our understanding of flotation chemistry.

Jan 1, 1989

By Kevin A. Foo, Joseph L. Young, William W. Reid

The title of this paper is "Designing Very Large Bio-oxidation Plants". To our knowledge, only one such plant has been designed and built to date, and that is U.S. Gold's Tonkin Springs plant in Nevada. This plant was commissioned in Spring of 1990 and operated for a short time successfully as a bio-leach plant but U.S. Gold did not have the financial strength to overcome the consequences of construction delays and increased capital cost. The plant has temporarily been 1 put on a standby basis. Recently, < > a potential joint venture between Tonkin Springs Gold Mining Company and Homestake Mining was announced. Homestake will operate the mine with the technology and subsequent improvements would be co-owned by both companies. This paper is not a "how to" type publication because we feel that such an approach could be dangerous if used improperly. Rather, we discuss some of the important aspects of process selection, testing and design that need attention, and some of the lessons learned to date. As with all developments, improvements and new knowledge will accrue as more companies use bio-oxidation technology. The Tonkin Springs plant is fair evidence that bio-oxidation has "arrived" as a technology, and that successful design and operation of plants treating greater than 1000 t/d of feed is possible.

Jan 1, 1990

By W. Belobraidich

Kennecott&apos;s Ray mine is located about 145 km (90 miles) north of Tucson in the Mineral Creek mining district of central Arizona. Mining in the district started in the late 1800&apos;s. The Ray mine itself was first mined by under- ground methods in 1911 and was changed to an open-pit operation in 1952. Mineralization is complex and includes sulfide, silicate, and native copper mineralization, as well as minor amounts of molybdenite. Sulfide ore, mined at Ray, is shipped by rail to Kennecott&apos;s concentrator and smelter at Hayden, 32 km (20 miies) away. Silicate ore, mostly chrysocolla, is processed near the mine in a vat leaching-electro- winning plant. The mine consists of two sulfide areas: (1) the West pit and the Central pit (the original Pearl Handle pit) and (2) a silicate area on the northeast perimeter of the Central pit. The pit now is over 304 m (1000 ft) deep and approximately 3048 m (10,000 ft) long. Roads within the ultimate pit are limited to a grade of 10%, while those outside the pit are limited to 8%. The mining equipment consists of 40 Wabco 1094 (120-st) haulage trucks [ranging from 109 to 227 t (120 to 250 st)], 12 electric shovels [ranging from 6 to 23 m (7 to 25 yd)], and 3 11-m (12-yd) Dart production loaders.

Jan 1, 1979

By B. E. Penrod

The main constituents of flat glass are the eight commonest elements of the earth&apos;s crust. Five of these, silicon, sodium, calcium, magnesium and oxygen are essential. Two more, Aluminum and potassium have beneficial properties. For colorless glasses iron is undesirable, in standard clear glasses a small amount of iron is tolerable, while for most tinted glasses iron is essential. These elements are present in glass as oxides and because they are so common there is no foreseeable resource shortage. The availability of supplies of materials at particular sites at prices which enable a glass manufacturer to be competitive may be another matter. In this paper it is intended to provide a historical perspective to the current situation, to contrast some of the traditional North American and European practices, and to progressively review some of the driving forces for future change and to attempt to assess their effects upon both raw material supplier and consumer.

Jan 1, 1994

By A. L. Mula

Pasaremos revista brevemente a 10s fundamentos de 10s ciclones, considerando un ciclón típico. Los datos gráficos disponibles en la literatura han sido convertidos en ecuaciones matemáticas por conveniencia. Se suministran los procedirnientos preliminares para seleccionar y diseñar tanto los ciclones como las bombas, y se facilita con algún detalle un ejernplo de cálculo para un hipotético circuito de molienda. En general, debe consultarse a 1os proveedores de ciclones y bombas para determinar un disefio definitivo. Algunos suministradores de ciclones emplean normalmente computadores digitales para el diseño definitivo con objeto de asegurar una gran precision.

Jan 1, 1982

By Q. Yuan, B. Yarar

Steric stabilization is a phenomenon observed when relatively high doses of flocculants are added to fine particle suspensions. Experiments were conducted to establish conditions under which medium viscosity and the sedimentation properties of black sand components in a slurry could be controlled so as to enhance the selective sedimentation of gold grains. It was shown that black sand concentrates containing as low as 2.65 g/mt gold could be upgraded by selectively hindering the sedimentation of non-gold components in an aqueous slurry. This paper presents data describing the theory and practical implementation of this cyanide or mercury-free novel approach where gold could be concentrated by as much as 15 times with relatively high recoveries. The relationships of solids content of slurries, type and dose of polymers with the recovery process are documented. Key words: Gold, black sand, selective flocculation, steric stabilization.

Jan 1, 1993

By Ernesto Maldonado, Jesus Romero Benitez, Zach Agioutantis

Numerous researchers worldwide have investigated the prediction of ground movements due to underground coal mining utilizing different analytical, empirical, and numerical models. These studies have primarily focused on the development of prediction methodologies for either flat or gently dipping seams under variable topography, and only a few studies are available that have investigated the prediction of ground movements over inclined seams. Although most inclined coal seams are in China, India, and other countries worldwide, a few inclined coal seams (with a dip of 10 degrees or greater) are also present in the US. Currently, the prediction of ground movements for inclined coal seams using empirical methods utilizes the same methodology for horizontal seams. It consists of dividing the inclined seam into horizontal segments, calculating deformations due to each segment, and superimposing the calculation results. This paper presents a new tool that provides a methodology for modeling subsidence under inclined seam conditions. Examples based on subsidence measurements available in the literature are presented. The goal is to implement this methodology into the Surface Deformation Prediction System (SDPS).

Jun 25, 2024

By Sam H. Patterson

The advances in knowledge of world bauxite resources in the last few decades include contributions to the geology of deposits, discovery of large resources, shifts in availability, and changes in. the industry in response to political and economic pressure. Improvements in the understanding of geology have resulted from the larger numbers of geologists working on bauxite and better exchanges of information. The large deposits discovered are mainly the laterite type in tropical regions. These discoveries have led to major increases in bauxite resource estimates as well as to shifts in bauxite availability and in the ranking of producing nations. Changes resulting from political, environmental, and economic pressures have resulted in increased costs of bauxite and in renewed interest in potential nonbauxite sources of aluminum. Aluminum is produced from nonbauxite raw materials only in the U.S.S.R.; however, research on extraction processes or investigations of nonbauxite alumina resources has taken place in several countries.

Jan 1, 1984

By John A. Herbst, William T. Pate

Column flotation is emerging as one of the most important new separation technologies of the decade. Attendant to this development is the need for a quantitative understanding of the dynamic characteristics of columns. An understanding of the many important sub-processes occurring in the cell makes possible the development of dynamic simulators for flotation columns which will aid in the design of control systems for dynamic and steady state optimization. This paper presents a dynamic model for the column flotation cell developed from a population balance point of view similar to that which has been successfully applied to conventional flotation cells. In particular, the mixing that occurs within the pulp is modeled with a distributed-volume, mixer-in-series model as an approximation to the axially dispersed plug flow transport that occurs in the cell. This simpler approach avoids the distributed transport model which often leads to mathematical intractability. Other phenomena dealt with are the attachment and detachment of particles from bubbles in the froth and pulp, the transport of water and the bubble volumes with the froth and pulp phases. Simulation of the flotation of an Illinois No. 6 coal in a pilot plant flotation column were performed to test control strategies.

Jan 1, 1989

By B. Rao Pothini, Julio H. Thaler, W. L. Finlay

The White Pine room-and-pillar mine started in 1955 from a suboutcrop, down gentle dips, and with a competent sandstone roof. As mining depths increased, extraction decreased 1% every 35 feet. Moreover, roofs became shaly and less competent, and regions of high fault and joint densities, sometimes with and some- times without high lateral stresses, increased the tendencies towards roof falls. Instinctive reactions towards narrower openings did not alleviate the problem. Careful consideration of rock mechanics principles culminated in the development of two variants to the conventional room-and-pillar mining system based on the concept of stress relief through load deflection. The two systems-EquiAdvance Cave, and PressureArch Panel Mining-are complementary. The objective of the former system is to provide relief from lateral stresses through advance caving and in the process also to achieve higher extraction at depth. Where surface subsidence cannot be allowed, the alternative PressureArch Panel concept is utilized to provide stress relief and moderately high extraction ratio. Both systems have been under trial for over three years and, together, produced over three million tons of copper ore. These two systems, and their production test results to date, are described.

Jan 1, 1977

By Henry R. Tiedemann, Eugene H. Skinner, George E. Wickham

Improving the state-of-the-art of tunneling is a continuing challenge to those involved in underground construction. New methods and procedures are usually evolved over a relatively long period of time as compared to advancements in other types of construction. To a large extent this is probably due to the fact that tunneling deals with a material or medium - the rock structure - whose physical properties are not only extremely varied, but in many instances virtually unknown until time of penetration. This hovering of the unknown tends to make "non believers" of many and at best leads to a general reluctancy of accepting new ideas or procedures. The situation is further complicated by: 1) discrepancies in terminology and respective meanings as used by different disciplines to describe, define or evaluate pertinent factors and their relative effect on the tunneling process and 2) the fact that no two tunneling situations are identical with respect to either geological conditions or construction and contractual requirements. In spite of the above there have been many successfully completed tunnels which make it apparent that both the technical and practical expertise needed to develop or project improvements is available within the industry. It is with this in mind that the RSR concept was developed. BACKGROUND This paper presents the findings and results obtained from contin-

Jan 1, 1974