Search Documents

By Terry M. Hertel

The chemistry of waters processed by Acid Rock Drainage water treatment plants can affect the Total Suspended Solids quality of the plant effluents. The sulfate ions in the ARD water will combine with the calcium ions from the lime that is used to adjust pH to form calcium sulfate. When the sulfate content of the waters to be treated is greater than about 1400 parts per mil­lion, the resulting calcium sulfate concentration will be approx­imately 2100 parts per million. This concentration is above the saturation point for calcium sulfate, and the salt will drop out of solution until the concentration falls below the saturation point. This "salting" phenomenon affects the total suspended solids of the treatment plant effluents by virtue of the fact that the salts will report to the filtration apparatus used for the analy­sis. This scenario is exacerbated as an effluent sample ages. Zortman Mining's water treatment plant effluent was being affected by "salting" during the spring and summer of 1995, and it seemed as though the effluents were exceeding the TSS lim­its; for no obvious reason. A testing program was initiated to verify an observation that "salting' was taking place. Treatment plant samples were collected and allowed to age, with TSS analyses being performed every day that the samples aged. Synthetic solutions were also prepared to study the "salting" phenomenon.

Jan 1, 1996

By R. H. T. Garnett

Recovery performance may be measured in absolute terms or in relative ones that relate the actual mining outcome to what was expected. Consideration is possible in terms of the control exercised by the operator. The eventual mineral output is the only figure known with complete certainty. The paradox is that, while performance is judged against the sampling, the reverse also applies. The R/Efactor and its four component factors are the best overall measures of performance. The choice of equipment for sampling and mining is very important. The sampling process may introduce errors and the sample density may lead to poor mining block selection. The resulting recovery performance is most visible on a regression curve. Changes in the cutoff grade must also be taken into account to avoid unrealistic production targets. Estimation methods incorporating different mathematical assumptions and techniques may cause over-or underestimation of the grade and volume. If the selective ability of the mining equipment does not match the size of the reserve blocks, the performance will be compromised. The treatment plant efficiency, the throughput rate and the degree of bedrock clean-up also affect performance. The maximization of throughput does not yield the optimum results. Marine conditions, which are outside the operator's control, affect not only operational availability but also performance. Examples are provided from actual operations for various commodities, showing the relative magnitude of the different effects upon performance.

Jan 1, 1999

By John Batty, Rennie Stallknecht, Dave Dew, Rennie Marais

GENCOR was contracted by Lonrho Plc of London to design a treatment plant for the benificiation of ores from the Amantaytau Goldfields in Uzbekistan (CIS). The testwork required for determining the design parameters was conducted at GENCOR Process Research in Randburg South Africa, on large bulk samples of ore shipped from the CIS. The initial milling and flotation testwork was designed to both optimise the conditions for maximum gold recovery, and to provide flotation concentrate for subsequent testwork. The concentrate produced was fed to a pilot scale BIOX® plant, and at the client's request a portion was shipped to specialists in roasting and pressure oxidation technology for comparison. Besides the testwork conducted at the GENCOR Process Research Laboratories in South Africa, the client also requested that the testwork be repeated at the Ingichki Research centre in Uzbekistan to demonstrate to their CIS joint venture partners that the results obtained in South Africa are reproducible and to demonstrate the ease of operation of a BIOX® plant. Pilot scale equipment was air freighted to Ingichki where the results of the testwork obtained in South Africa were successfully duplicated. BIOX® technology was shown to achieve higher gold recoveries than either roasting, whole ore roasting or pressure oxidation.

Jan 1, 1995

By Robert W. Bartlett

Heap biooxidation of sulfidic refractory gold ore requires large amounts of oxygen, as shown in Figure 1. Bacteria, Thiobaci/lus ferrooxidans, are donnant at oxygen concentrations below about 3% in air (1 ppm in aqueous solution) because ofmonod kinet­ics. Hence, the maximum possible utilization is only about 75%, and it may be much less than that due to poor air sweep effi­ciency. At the maximum oxygen utilization, an ore containing two percent pyrite requires nearly 100 cubic meters of air per tonne (4,000 cubic feet per ton). The stoichiometric air require­ment to oxidize arsenopyrite is similar to that of pyrite. While the leaching solution percolating through the heap introduces some dissolved oxygen, the amount is insignificant because of the low solubility of oxygen in water, 7 to 8 ppm at atmospheric saturation. There are only three ways to provide oxygen to the heap: either air flow by natural convection, diffusion of oxygen from the surface (through stagnant air in the air-filled void space in the heap), or forced air ventilation of the heap. Each of these processes will be reviewed.

Jan 1, 1996

By R. Hagemeyer

In North America, the paper industry is by far the largest consumer of coating and filler mineral pigments. Present use is at an annual rate of 5.5 million metric tons with a value of $660 million. Current estimates are 65 percent is used in coating and 35 percent in filler applications. During the past decade, the switch to alkaline papermaking has provided the opportunity to substantially increase filler levels while maintaining paper strength. As a result filler consumption has been growing at a late in excess of 15 percent yearly. Unfortunately, within a few years, mandated recycling could slow or even reverse this trend. The critical issue is finding an economically viable method for recycling the mineral pigment and/or minimizing the disposal problem

Jan 1, 1994

By Amoussou Coffi Adoko, Shevaune Zeng, Sebastian D’Hyon, Gareth Kennedy, Eleonora Widzyk-Capehart

Inertization of coal dust with stone dust is a common control implemented within underground coal mines to mitigate the hazard of a coal dust explosion. To achieve adequate inertization, the total incombustible content (TIC) of the coal/stone dust mixture is required to meet certain percentages depending on the risk and relevant legislation. Current methods for determining the TIC of a mixture involves laboratory analysis, colorimetric comparison, or the use of portable instruments. This paper provides preliminary analysis of determination of a sample’s TIC in real-time with chemometric modelling, using portable instruments employing near-infrared (NIR).

Feb 1, 2024

By C. R. Zegarra

Extraction of manganese, gold, and silver from a low-grade manganiferous-silver ore was investigated by thiourea leaching followed by standard cyanidation. The levels of reagent concentrations in this investigation were 0.0 -1.0 M thiourea and 0.0 -1.0 M sulfuric acid. Temperature and agitation speed were maintained at Z5 °c and 300 rpm, respectively. The dissolution of gold, and silver was shown to be dependent mainly on sulfuric acid and thiourea concentrations. In general, 50.0 % Ag, 98.0 % Au, and 75 % Mn were recovered from a Mn-Ag ore by thiourea leaching. Overall silver extraction of 98.0 % was obtained by cyanidation after thiourea leaching. Thiourea leaching of sodium bisulfite leach residues was also studied, and the total extraction of gold and silver were 97 % and 40 %, respectively. Finally, a two-stage thiourea leach was also investigated.

Jan 1, 1988

By H. E. Rowen

I hope my title is not confusing; even more so that I am not. Actually pelletizing and sintering, meaning both the formation of pellets and the hardening of them, are closely related to each other and to phenomena of nature. Figure. 1 This many-celled porous structure, frozen as it was at the fusion temperature and was being frothed by fast-moving gases, may be considered a typical piece of sinter. The same structures have been found in natural ores.

Jan 1, 1962

By S. S. Cook, S. E. Paulson

The US Bureau of Mines is conducting core leaching experiments with sulfuric acid on oxide copper ores from the Cyprus Casa Grande and Asarco/Freeport Santa Cruz deposit in Arizona to further the understanding of the leaching process in supergene copper ores as it relates to in situ mining. Leach solutions from atacamite mineralization contained 5 to 30 g/L (0.05 to 0.28 oz/gal) copper and few extraneous ions. Leachant from chrysocolla ores, with grades similar to the atacamite, contained 2 to 9 g/L (0.02 to 0.08 oz/ gal) copper and abundant extraneous ions. Quartz and K-feldspar had no impact on leach solution composition at any acid concentration up to 40 g/L - (0.39 oz/gal) while illite and sericite had minimal impact. Biotite, calcium-rich clay, and limonite have a significant impact on solution chemistry when there is abundant free acid in solution. High acid concentra¬tions increase acid consumption in ores with abundant biotite and limonite gangue. High acid concentrations can be used in ores with quartz, K feldspar, and sericite gangues without increasing acid consumption per unit of copper removed.

Jan 1, 1990

By T. Eggenberg

Mechanization and automation of logistic equipment has become one of the main key factors in raising productivity and competitiveness especially for complex and larger mining or tunneling projects. The Lake Mead Intake Tunnel #3 shaft mucking installation is a good example to demonstrate the potential that is found in an overall optimized logistic. It starts with the planning and results in using customized installations which fulfill the specifically defined requirements for the project. Rowa developed a solution and supplied a shaft mucking system using a discontinuous double drum hoisting concept with shaft buckets, loading, and unloading devices. With this fully automated system a continuous muck flow of 437t/h can be achieved.

Jan 1, 2010

By M. Cambridge

The design process must anticipate all construction and operational conditions and make an allowance for all eventualities. Prevention of failure during operational life, and in some cases post abandonment, requires that a risk assessment is undertaken during the design stage which defines not only the factors of safety to be used but the criteria for the structure during its operating life. These operating criteria should clearly identify the at-risk structures and the inspection and monitoring routines required to ensure compliance with the design objectives. On a mine site, it is the role of mine management to ensure that the operating rules be applied throughout the mine life and that a system of inspection and monitoring procedures be instigated. Where the risks are significant, high-level auditing by an independent engineer will also be required. Within the inspection and auditing framework, the designer needs to incorporate instrumentation to enable the operators and management to confirm that the facility meets the requirements of safety, stability and environmental compliance whilst continuing to meet its operational function. This paper reviews the use of inspection and monitoring to prevent failure and provides, in summary, examples of where monitoring has been undertaken and prevented failure. A tabulated review of legislation, regulations and technical guidance generated as a result of previous failures or untoward events is provided.

Jan 1, 2005

By Luis Tondo, Gary Johnson, Steve Morell

High pressure grinding rolls have been demonstrated by numerous researchers, and at a number of commercial installa­tions to be power efficient comminution devices. They have become almost "standard equipment" in the grinding of cement clinker. However, the technology has been relatively slow to catch on in the mineral processing industry. Part of this may be due to the fact that this relatively expensive machine has not been incorporated into the plant flowsheet so as to fully exploit its power efficiency, and therefore realise the maximum economic benefit. This paper describes the results of a pilot scale test program designed to evaluate the performance of the device with the aim of developing a circuit configuration that better exploits the inherent power efficiency of the machine. The results of the test program clearly show that power savings of about 50% over conventional technology are achievable when the machine is made to produce the final product grind size.

Jan 1, 1995

By Andrzej Luszczkiewicz, Kazimierz S. Sztaba

Flotation tailing of Polish copper sulfide ores represents more than 90% of the mass of run-of-mine ore. The tailing contains mainly quartz, dolomite, clay minerals, traces of sulfides, and some accessory minerals. Almost all minerals of the tailing are well liberated and, therefore, any further beneficiation process applied to the tailing is expected to be inexpensive. In this work, results of investigations on utilization of flotation tailing using classification and gravity concentration are presented. It is shown that due to classification of flotation tailing in hydrocyclones, the coarse fraction becomes suitable material for gravity separation providing backfill material for underground mines as well as heavy minerals, a source of valuable rare elements. It was also found that heavy minerals separated by gravity methods contain a significant amount of rare elements such as zirconium, titanium, silver, rare earth metals, and uranium. The light fraction of the gravity separation contains well deslimed quartz particles and meets strict requirements for hydraulic filling material ked for structural support in underground mines. Evaluation of the cost of the proposed technology indicated that investment to implement the method would provide a return within 2-4 years.

Jan 1, 1995

By M. Wason

An Ore bed magnetic liner element is made of permanent ceramic magnets embedded in a rubber molding. (See figure 1) They are difficult and expensive to manufacture correctly. Therefore, the lining for a complete mill is expensive, as high as 400% more than conventional rubber liners. The magnets are not very resistant to impact as they are very brittle. Mills of 12 feet or more can use only I inch balls; mills under 12 feet can use balls of 1-1/2 inches. These liners are therefore used in regrind applications with small balls or in secondary pebble mills. Rubber liners for these applications last a long time, so if life was the only consideration, the pay back for these liners would be longer than the life of the mine. The Ore bed liner and its bed of ball chips or magnetic ore is relatively thin and the surface of this bed has a high coefficient of friction. The liners are made so that opposing poles are situated next to each other and that the mill shell and the bed of ore or ball chips completes the magnetic circuit. (See figure 2) The combinations of these properties results in a very efficient liner. Due to the low profile of this bed, there is no material that is lifted too high, so we have a very compact charge with very high attrition, good for fine grinding. These liners have shown a 10% ball consumption reduction and a 10% lower power draw for the same capacity. Due to the magnetic orientation, the bed is formed in a wave shape along the lines of magnetic force. Tests conducted at a copper mine in the southwest United States have confirmed these findings. The mills where the liners were tested are 10.5 feet by 16 feet Hardinge regrind mills operating as overflow ball mills.

Jan 1, 1999

By Bobby G. Wixson

The computer aided mapping of lead concentrations in soil has been carried out around the Doe Run (formerly AMAX-Homestake Lead Toilers) primary lead smelter near Boss, Missouri, through a cooperative Missouri Research Assistance Act program between the lead industry and the University of Missouri. As a part of this research a sequential extraction method was also developed to analyze and determine the various species of lead in the vicinity of the smelter as to possible sources which would suggest pertinent environmental control measures. Practical applications of this data-based scientific approach will be presented.

Jan 1, 1988

By John M. Wootten

The development of new coal markets is -t upon the ability to utilize coal in an environmentally acceptable and economically viable fashion. Foremost in the concerns about coal utilization is the impact its combustion has on air pollution. Concerns over environmental issues, such as acid rain, are currently one of the major impediments to the development of new coal markets. The Department of Energy and the Synthetic Fuels Corporation are addressing certain aspects of the development of new technologies for the utilization of coal. However, at the present time, there is a void in the new technology development process. That void is the step from proof- of-concept to commercial demonstration. Congress has established the Clean Coal Technology Fund at a level of $750 million to fill this void. The Department of Energy, in a solicitation of interest, received over 175 proposals for commercial demonstrations of clean coal technologies. A review of these solicitations indicates that $1.2 billion worth of research could be accomplished with a federal cost sharing of $425 million or 35 percent of the total. Industry has indicated, through this response, its willingness to invest its limited funds on projects it feels have the greatest potential for the clean use of coal. What must now occur is that Congress must appropriate the monies from the fund to initiate the commercialization of these clean coal techno1ogies.

Jan 1, 1986

Semiautogenous (SAG) ball mills are being increasingly used today for the coarse grinding of a range of ores, including gold, copper and iron. Larger mines are demanding mills with larger throughputs. This has led to some remarkable developments in mill diameters and installed powers. Conventional design principles - mills with trunnion bearings - have reached their limitations. This article describes one SAG mill with a slide-shoe arrangement and Krupp Polysius' Combiflex twin drive. In August 1997, the world's largest SAG mill with a slide-shoe arrangement was commissioned in Queensland, Australia, operating as a wet mill. The inside diameter is 10.4 x 5.1 m (34 x 17 ft) effective grinding length. The 1.36-ktlh (1,500-stph) SAG mill is driven by two Combiflex drives (twin drives with 2 x 5,500-MW or 7,375-hp installed motor power) in conjunction with a girth gear (outside diameter 11,890 mm or 468 in.). Commissioning of the SAG mill was completed with no notable technical difficulties. The plant runs continuously except for planned maintenance stoppages and process-specific reasons. As this article is written, the machine has been in operation for about 8,000 hours without major problems.

Jan 1, 1998

By D. M. Galbraith

British Columbia's physiography - the mountains, valleys and watercourses - provides the basis for rich and varied plant and animal resources and for complex land uses. Mining alters the physical environment in a manner that may create a disproportionate impact on biological resources and land use systems. The object of environmental legislation is therefore largely the protection of the basic physical environment: land surface, water, and air. The pace of mineral exploration, placer mining, and underground and surface gold mining has recently quickened in British Columbia, testing the ability of both industry and regulatory agencies to respond to legislative requirements. Some parameters of mining activity have critical significance for environmental protection, for example: the area disturbed; the physical and chemical qualities of ore, waste and overburden; and the nature of materials handling. Acid mine drainage is a particular hazard. Provincial legislation that applies to mining includes the Mines Act, the Environment Management Act, the Waste Management Act, and the Water Act. Government of Canada legislation includes the Fisheries Act and the Metal Mining Liquid Effluent Regulations. Every new mine proposal in British Columbia is reviewed in the Mine Development Review Process, which receives its mandate from the Provincial Environment and Land Use Cabinet Committee. The proponent submits reports to the Mine Development Steering Committee in succeeding stages: Prospectus, Stage I (after which approval-in-principle may be granted by ELUC); and if necessary Stage 11. Stage 111 is the

Jan 1, 1987

By Archie W. Fletcher, R. J. Wesely, Nathaniel Arbiter, A. D. Zunkel

In contrast to pyrometallurgy's six thousand year history in the production of metals, that of hydrometallurgy is of relatively recent origin. The earliest reference to it at all was in the 16th century, with the first applications to copper in the 17th and 18th. In the 19th century, increased demands for pure metal resulted in development of electrolytic refining, and early in this century electrowinning. The rapid growth in wpper production in the present century, paricularly in the United States and Chile, stimulated the development of new technology for leaching, and for the recovery of copper from leach solutions. Solvent extraction has become a major factor during the past quarter century by permitting novel leaching technology which produces dilute or complex solutions. In addition, solvents other than sulphuric acid, and chemical methods for precipitating copper metal are now of increasing interest. These are trends which should grow in importance in the future with the need to process lower grade and more complex materials. The evolution of copper hydrometallurgy is reviewed briefly and key factors in recent major developments are presented with details of specific operations and with trends for the future indicated. The relative importance of copper hydrometallurgy is compared to that of pyrometallurgy in the light of probable changes in ore supplies and character.

Jan 1, 1993

By T. Janke

When Homestake Mining Company's Mclaughlin Gold Project was being evaluated for development, it was apparent that recovery of gold from mined ore would be difficult and relatively expensive. The ore was refractory, averaging less than 50% recovery in conventional direct cyanidation milling tests. Extensive testing narrowed the processing choices to either autoclave or roaster oxidation before cyanidation. Roasting was ruled out due to higher capital and operating costs --the Mclaughlin mill would be the first large-scale application of autoclave oxidation of a refractory gold ore.

Jan 1, 1989