Search Documents

By Helen Joyce, Larry Twidwell, Jay McCloskey, Eric Dahlgren, Andy Hadden

The reduction of dissolved selenium oxyanions from mine wastewater utilizing an elemental iron cementation technology on been studied on a laboratory scale at Montana Tech of The University of Montana and on a pilot scale at MSE-Technology Applications as a water treatment process potentially capable of removing dissolved selenium to GO WL. Laboratory and pilot scale studies using elemental iron have demonstrated effective removal of dissolved selenium. Enhanced selenium reduction rates have been demonstrated when galvanically coupled iron/copper and iron/ nickel are utilized. The laboratory and pilot scale results are presented and discussed.

Jan 1, 2005

By Steven J. Schatzel, Mark M. Mazzella, Robert A. Kimutis, VASU GANGRADE, James D. Addis, Marcia L. Harris, Mayley Guitard

Researchers from the National Institute for Occupational Safety and Health (NIOSH) evaluated the impact of potential shale gas well breaches and subsequent gas inflow on selected mine ventilation systems of operating longwall panels using a 1:30 scaled Longwall Instrumented Aerodynamic Model (LIAM) and Sulfur hexafluoride (SF6) as a tracer gas. A series of tests were performed at 340, 400, and 500 cfm inflow levels utilizing different mine ventilation scenarios. Results suggest that the breached gas can be diluted to meet statutory levels when the longwall panel is adequately ventilated. The results enhance the understanding of the gas inflow and mine ventilation system interaction and provide critical information to the industry and regulatory agencies for improving miners’ safety.

Feb 1, 2024

By Michael Werner

A three-way research program, facilitated by the U.S. Bureau of Mines Generic Institute funding, conducted by Hecla Mining Co., Spokane Research Center of the Bureau and the University of Idaho, shows that a cooperative effort to solve difficult mining problems should be considered. A five-year plan to change an overhead cut-and-fill mining system to a longwall undercut-and-fill involves more than twenty people from three organizations. The investigations will eventually include, ground stress, stress analysis, fill selection placement and compaction, ground and fill support, underhand mining and materials handling, access, ventilation, equipment selection and synthesis and operations and cost simulation.

Jan 1, 1985

By D. Y. Geng

Longwall mining is a relatively new mining method in the United States. Early trials in the eastern and central coal fields were not successful, mainly because, among others, the face supports did not have sufficient capacity. It was not until in the late 1960's, when the high- capacity self-advancing powered supports became available, that longwall mining was successfully reintroduced. Since then the number of mines employing the longwall method has been steadily increasing. It has reached approximately 7.5% in 1981. Currently longwall mining is used mainly in the Appalachian coal field. The seam depth ranges from 150 to 2500 ft. but mostly between 300 and 1400 ft. The seam thickness ranges from 32 to 144 inches with the majority between 40 and 100 inches. Nearly all longwall mining are in flat or nearly flat seams extracting in single slice, although one inclined and one thick seam longwall mining have been either operated or initiated in Colorado.

Jan 1, 1983

By T. Gollaher

The use of paste thickeners for mineral tailings has gained increasing acceptance by the mining industry throughout the world and in the U.S. during the last five years. Advantages of water recovery and environmental sustainability are the driving forces for paste as an alternative to conventional thickening and the slurry pond. This paper presents a summary of the differences between paste and conventional tailings thickeners, along with recent examples of full-scale paste thickener installations.

Jan 1, 2010

By Chris A. Minnucci

In 1978, the U.S. Department of Energy funded a 2-year study to identify and quantify causes of the post-1969 coal mine productivity decline. A large number of factors hypothesized to have affected productivity during this period were analyzed using regression techniques. The results were particularly interesting for two of the factors--mining method and shift scheduling. The study results indicate that the use of longwall mining has an insignificant impact on overall mine productivity, compared to other methods, and mines operating on a two-production shift per day schedule are more productive than mines employing other shift schedules.

Jan 1, 1984

By D. R. East

Recent experiences within certain sectors of the international mining industry suggest an underestimation of the environmental risk associated with the design of mine waste management facilities. These experiences show that the technical and managerial challenge of responsible mine waste management is not always fully appreciated. Unfortunately, the image of the mining industry's environmental performance is negatively impacted by a relatively few number of failures. This negative view overrides the many positive contributions made by the majority of mining companies. The fact that these failures continue to occur to this day in both developed and developing countries is indeed remarkable, and indicates a degree of risk-taking approaching unacceptable levels. The design requirements for tailing storage facilities are, in many cases, more demanding than those of conventional water dams, because seepage of fluids which contain dissolved metals may pose a greater threat than the mere loss of water.

Jan 1, 1999

By Ethan Steward, Kyle Perry

The study investigates the effects of high-velocity impacts of common mine materials on a reinforced mine seal rated to 120 psi. It found that materials propelled during an underground explosion could generate enough stress to crack or damage seals, even with little visible damage. This highlights the need for careful evaluation of mine seals after any impact or high-pressure event.

Aug 1, 2023

By Kevin Andrews, SETAREH GHAYCHI AFROUZ

Ground control analysis and groundwater inflow assessments for underground coal mines require in-depth field investigations including, but not limited to, geological and geotechnical core logging, downhole geophysical logging, laboratory rock strength testing, and packer (Lugeon) testing. Field and laboratory data collection are time consuming and expensive, and an initial understanding of the expected trends among various geotechnical and hydrogeological parameters can assist with the planning and optimization of geotechnical characterization studies and grouting plans. In this study, a comprehensive database is analyzed, comprised of important rock mass characteristics (hydraulic conductivity, rock quality designation (RQD), and lithology) for coal-bearing rocks in the Central Appalachian Basin. Statistical analysis of the data is completed to establish an enhanced understanding of geotechnical and hydrogeological conditions expected to be encountered as underground coal mining passes near and beneath streams and rivers. The results of the study provide valuable reference material for the coal mining industry for completion of shaft installations, mine stream crossings, environmental assessments, and grouting and mine dewatering designs.

Jul 1, 2023

By Bennett D. Lass

A new method for determination of residual flotation oils on beneficiated kaolin clays has been developed. The method, which yields qualitative information, is based on fluorescence measurements employing a spatially resolved, polychromatic illumination source for excitation, and a two-dimensional detection scheme using a silicon-intensified, video imaging device. The method was used to identify residual oils on a beneficiated, Washington County, Georgia, crude clay. The results were compared to a similar qualitative analysis performed via capillary column gas chromatography using an FID detector. The video fluorometry was the preferred method of, analysis.

Jan 1, 1983

By William Tattersall

On behalf of my agency, the Mine Safety and Health Administration, I would like to add my appreciation that all of you could be here today. Previous dust symposia over the years have proved the value of close cooperation among universities, government agencies, and professional societies in advancing knowledge of dust research and development in the interest of miners and the industry. I'll just comment briefly on MSHA's part of the overall effort by all parties to control miners' exposure to respirable coal dust and other airborne dusts. As you know, our agency's congressional mandate is to do what is necessary to assure that miners will have safe and healthful workplaces. In the area of coal mine health, this has meant joining with the mining community in a continuous campaign to keep respirable dust and quartz levels below applicable standards to prevent or reduce disabling coal workers' pneumoconiosis and silicosis arising from excessive exposure to respirable quartz. Currently, our agency is processing about 120,000 coal dust samples taken by MSHA and company people during the year and about 8,000 samples taken from metal and nonmetal mining operations. Our dust program, like other MSHA programs, has benefited from increased computerization of records. The attack on CWP has had the highest priority of government and industry. The goal has been to sharply reduce social costs of suffering victims and their families as well as the associated future payments under the black lung benefits program. During the 1989 fiscal year, about 104,000 former miners received about one and a half billion dollars in benefits. Since the program began, nearly 25 billion dollars have been paid out. Much progress has been made in lowering dust levels in coal mines since the standard of two milligrams per meter of air was established in 1972. Before that time, there was a 4-to-10-percent probability of a miner developing coal workers' pneumoconiosis at typical pre-1972 exposure levels. However, under the maximum respirable dust levels allowed today, this probability has been reduced to about 1 percent. Since average dust levels are lower today, we can expect fewer miners to develop CWP in the future. Out goal continues to be elimination of both coal workers' pneumoconiosis and silicosis in both coal and nonmetal mining. In 1985, MSHA revised its coal mine quartz policy to allow mine operators to submit dust samples used in setting the quartz standard. Previously, only single MSHA samples were used. Even though less than half of the mine operators have taken advantage of this change, it has provided a larger population of samples for analysis then before. Also the policy allows operations that are on a reduced quartz standard to have the standard reviewed every six months. In underground coal mining, the job of roof bolter typically has higher than normal exposures to quartz. About 45 percent of respirable dust samples from roof bolting operations contain more than 5 percent quartz and therefore are put on a reduced quartz standard. One objective of the policy revision was to improve miners' health by follow-up monitoring, and this is being done with roof bolting jobs. MSHA studies of surface coal mining operations have provided data showing that bulldozer operators and highwall rotary drill operators often have high exposure to quartz dust, and our agency is directing enforcement efforts to reducing this hazard. One of the most important responsibilities of MSHA's metal and nonmetal mine health division is the respirable dust sampling program. In the last few years, nearly 3 out of 10 samples have

Jan 1, 1991

By T. D. Barkand

A recent coal mine elevator accident resulted in serious injuries to four passengers. The miners struck the ceiling of the elevator car as it collided into the overhead structure at an estimated speed four times faster than normal. In response to mine hoisting accidents, safety authorities have required additional protective devices on new and existing mine hoists and elevators. This paper examines supplemental safety circuits and new devices designed to provide ascending car overspeed protection on mine hoists and elevators. These devices provide needed protection that eliminates the hazard or significantly reduces the potential of a mine hoisting accident.

Jan 1, 1995

By M. Rîsteiu

The authors aim to analyze the behavior of smart sensors using Transmission Control Protocol/Internet Protocol (TCP/IP) infrastructure in hazardous applications, because of their advantages regarding safety, expansion and Quality of Service (QoS). Initially, some constraints are discussed for these applications. Then, the possibility is analyzed of using 2.4 GHz TCP/IP based transmission for sending data out of an industrial area. In this setup the authors evaluated the round-trip implementation (which requires a database of packet lengths), related to the delay introduced by the radio transmission algorithms from 802.15.4, and 802.11d/g protocols. Tuning results of different varying time-delays were compared to the constant delay cases from the literature (Deák, 2003; Lincoln, 2003). Both the hardware and software setups are implemented. Based on TinyOS specific software for hardware checking/ initiating communication/ starting/ closing measurements the authors have developed separate/combined procedures for testing the integrated devices. Measured time delay is presented and analyzed, for both beaconed and non-beaconed 802.15.4 transmission, with power optimization criteria. By testing two different implementations (Zhang et al., 2001), (ATmega256 RZAV - 256KB flash memory, the CC2420 IEEE 802.15.4 and ZigBee-compliant RF transceiver core - 128KB flash memory) the authors have found some time delay variations as a result of local processing by the ZigBee controller with an amount of flash memory. The work is also focused on adapting industrial measuring standard systems to the smart sensors, but not only through the 4-20 mA standard.

Jan 1, 2008

By Thomas Schwind, Benedikt Grau, Angelos Gakis

"In Crossrail’s Farringdon station, compensation grouting was successfully utilized to mitigate the surface settlements induced by the tunneling works. The main focus of this study was the platform tunnels, which were approximately 300m long each and were enlarged to platform size using sequential excavation method (SEM) from the existing TBM running tunnels, initially supported using sprayed concrete linings. The rear grouting injections were carried out at a typical distance of minimum 5m above the completed, fully strengthened shotcrete lining hence inducing some additional stresses. In-tunnel monitoring using surveying targets was performed systematically to ensure that no excessive distortion of the initial shotcrete lining occurred. 3D finite element analyses were utilized to back calculate the actual “effective” pressure that was imposed on the completed shotcrete rings against the additional measured in-tunnel displacements due to the compensation grouting episodes. Additionally an assessment of the theoretical, “maximum” allowable grouting pressures that would lead to overstressing of the lining is presented. INTRODUCTION As part of the back analysis performed for the SEM tunnels in Farringdon station, an investigation of the effect of compensation grouting on the two constructed platform tunnels was undertaken. The platform tunnels were 10.6m high by 11.4m wide and approximately 300m long each. They were enlarged to their final shape from the existing TBM tunnels using SCL methods. This study utilized 2D and 3D finite element (FE) analyses in order to back calculate the observed tunnel crown displacement, assessing the equivalent grouting pressures during the rear injection episodes of the concurrent grouting operations. The results provide a useful reference for the order of magnitude of the grouting pressure load cases that can be applied in the numerical simulation of similar cases. Part of the results presented in this paper, were derived by the second author as part of his Master of Science thesis in Technical University of Graz."

Jan 1, 2016

The strength of anchorage of various types of roof bolts in permafrost depends on the types of rock in which they are installed. Variation in the mine thermal regime results in weakening of the roof and walls, and at times total loss of ice cement bonds takes place in the surrounding rockmass. In mines with positive ventilation air temperature, the wedge or expansion types of bolts may become weakened due to the transfer of heat into the anchorage through the metal rod and subsequent thawing of rocks. Effective operation and evaluation of roof bolt systems for mine workings in permafrost require predictions of the dynamics of wall thawing by warm ventilation air. This paper presents an analysis of the temperature distribution in the frozen host ground surrounding roof bolts, the area of interest being the vicinity of the anchors for point anchored bolt and the entire length for split set bolt

Jan 1, 1994

By H. Nematollahi

The comminution laws The grindability of the ores or minerals is an important factor that could not be deduced from their mineralogical characteristics (Testut, 1958). Many theories have been proposed to determine the amount of work required in a comminution operation as a function of the nature of material, size and shape of the minerals before and after of comminution. The most important laws are proposed by Rittinger, Kick and Bond. According to Rittinger (1867), the work is directly proportional to the new surfaces produced during the comminution. Kick (1885) believes that the work needed to produce similar modification is proportional to the volume or mass of the material. Bond, during his 25 years of experience and research, reached to the conclusion that on the average the energy required for a known comminution is between the Rittinger's and Kick's laws (Bond, 1952). According to Bond's Third Theory, the work input is proportional to the new crack tip length produced during the particle breakage, and equals the work represented by the product minus that represented by the feed. The work input is given by the following equation: [111W = 1 Owi( FP FF(1)] where W is the The energy input to the mill, (kWh/st); F is the Feed size based on 80% passed, (µm); P is the Product size based on 80% passed, (µm); and W; is the Work Index, (kWh/st) Methods to determine the Bond Work Index Various methods have been proposed by Bond to determine the Work Index. There are some problems with the Standard Bond Grindability Test: •Requiring a special mill. •Requiring a relatively large amount of sample. •Being relatively time consuming and tedious. [ ] During the recent years, numerous attempts have been made to install faster and easier methods to determine the Work Index. A complete description of these methods is presented by Yap et al. (1982). Determining the Bond Work Index by a new size ball mill During the recent years, researchers at the University of Tehran determined the Bond Work Index, using the Anaconda simplified methods by its Denver 305- x 127-mm (12 x 5-in.) laboratory wet ball mill. The equation used to calculate the Work Index for the above mill containing 16.12 kg (35.5 lbs) of steel balls is as follow: [1 _ 1-1W;=0.54x [P [)(2)] In addition, an attempt has been made to determine the Bond Work Index similar to standard Bond ball mill procedure but by a different ball mill, smaller and in consequent portable and less laborious than the Bond ball mill. Method description Just as the standard Bond grindability test, this method is a locked-cycle dry grinding and screening process that is carried out until steady state condition is reached. Test equipment The test is conducted in a special ball mill, called the New Size Ball Mill (NSBM). The mill is scaled down with a coefficient of two-thirds from the standard Bond ball mill. It measures 200 x 200 mm (8- x 8-in.) inside (instead of 300 x 300 mm or 12 x 12 in. in Bond ball mill). Just like the Bond

Jan 1, 1995

By V. Svalbonas

When the Trelleborg Divisions of Boliden Allis and MPSI merged, a unique opportunity occurred for two independent mill fabricators to compare various design procedures and the research upon which they were based. This paper documents such a comparison in the structural design area. Several SAG mill analyses are compared using both Boliden Allis and MPSI methods. The differences and similarities are then utilized in a correlation of critical stress definitions and the acceptable design and inspection criteria.

Jan 1, 1992

By S. L. Manske

The Mesquite gold deposit is a recent discovery of Gold Fields Mining Corporation lying 65 kilo- meters northeast of El Centro in Imperial County, California (Figure 1). The deposit is located on the southwestern flank of the Chocolate Mountains and is a bulk-minable, low grade "disseminated" orebody. Although the host rocks of the deposit are part of a regional high-grade metamorphic terrane, abundant brittle fractures, brecciation, and open-space vein fillings indicate that Mesquite mineralization is epithermal. Faulting which postdates the hydrothermal activity has complicated the original geometry of the orebody. Alluvium effectively hides most surface expression of the mineralization, but open-pit mining is now revealing the details of Mesquite geology.

Jan 1, 1987

By R. W. Lankston

Uranium mill tailings disposal facilities present unique problems with respect to siting, design, and long-term stability because their contents remain potentially hazardous for 100,000 years. Dawn Mining Company, operator of a uranium mill in Washington, undertook geological and geophysical studies relative to planned expansion of existing disposal facilities. Seismic refraction and reflection, resistivity, and ground magnetics data were integrated with limited drill data to determine the configuration of Quaternary sediments and the underlying basaltic and granitic bedrock. Analysis of multiple reflections and magnet modelling on a micro-computer with CRT graphics added detail to the interpretation.

Jan 1, 1980

By James S. Browning

This article describes research conducted by the University of Alabama's Mineral Resources Institute on removing sulfur from coal using a combination of gravity concentration and flotation methods. The research used the gravity and centrifugal force capabilities of Humphrey's spiral to remove part of the pyritic sulfur and ash. Flotation of the Humphrey's spiral coal concentrate removed additional sulfur and ash. In addition to obtaining good recoveries of high quality coal, the tests demonstrated that pyrite in the wastes could be isolated as enriched flotation products by the combined gravity-flotation approach. Domestic coal production in 1980 reached a record 757 Mt (835 million st). Forecasts are that coal production and use will approach 907 Mt (1 billion st) by 1985, with much of the increased production being used for electrical generation. Of current production, it is estimated that about 454 Mt (500 million st) of coal nationwide are subjected to some degree of cleaning, ranging from crushing and screening to gravity concentration and flotation. With expanded coal production and more rigid controls placed on coal combustion, it is reasonable to assume that the tonnage subjected to some form of preparation will increase, with time, thereby adding to the burden of coal rejects being generated. A major problem associated with increased coal use for electricity generation is the need for utilities to conform to emerging federal air quality standards for sulfur oxide emissions from power plants. To a lesser extent, other industrial operations burning coal face a similar situation. Controlling sulfur oxide emissions by using low-sulfur coal or resorting to stack gas desulfurization are two recognized approaches, but removing sulfur from the coal, if possible, by physical beneficiation before combustion is preferred because of its simplicity and lower cost. Reducing the inorganic sulfur in coal to tolerable limits by physical beneficiation, including flotation, as now practiced, is still relatively inefficient and has not kept pace with the more sophisticated physical beneficiation approaches generally employed by the nonfuel minerals industry. As one phase of a broad program conducted by the Mineral Resources Institute at the University of Alabama on sampling and evaluating impounded fine size waste coal, tests were made using samples from two impoundments to determine the quality of coal recoverable by a combination of Humphrey's spiral concentration and flotation. Particular attention was given to organic and inorganic sulfur deportment and distribution in the various products. Another objective was to determine if pyrite in the waste could be recovered for possible marketing. The use of Humphrey's spirals to concentrate fine coal was practiced as early as 1947. At that time, the Hudson Coal Co. used spirals to concentrate anthracite fines. In 1950, spirals were used to treat fine-size bituminous coal and later, in 1976, spirals were reportedly used for removing pyrite from fine-size coal. More recent investigations have discussed the use of Humphrey's spirals for treating fine-size waste coal in Alabama. Samples Description Washer waste samples were obtained from two impoundments. One sample was representative of waste generated during washing steam coal from the American, Pratt, and Nickel plate seams in Alabama. The other sample represented metallurgical coal washer waste from processing coal from the Carter, Johnson, and Milldale seams. Partial samples analyses are shown in Table 1, and screen analyses of the samples are given in Tables 2 and 3. Screen ana¬lyses showed that one sample contained about 4% of material coarser than 2 mm (10 mesh) and the other contained about 13% of plus 2 mm (10 mesh) material. Also, the analyses indicated that ash and sulfur increased as the material's particle size decreased. Experimental Laboratory Tests Sink and float tests using a heavy liquid (1.4 specific gravity) were made on the different screen sizes shown in Tables 2 and 3 to determine the effectiveness of gravity concentration for separating coal from pyrite and other gangue constituents. Tests indicated that gravity separation, under optimum conditions, could be expected to yield coal products containing 10-12% ash, and 0.2-0.3% pyritic sulfur. Good coal recoveries could also be expected. Using sink-float tests as a guide, tests were made in a Humphrey's spiral by a procedure in which a 90-135 kg (200-300 lb) portion of the

Jan 8, 1982