Search Documents

By David Wright, Colin Burns

Successful leaching of gold depends on appropriate chemical conditions; contact between leach solution and the gold particles; separation of the leach solution from the solids and extraction of the valuable ion from the solution. Irrespective of the leaching method employed the chemical conditions required are similar as is the dependence of solu­tion/gold contact on liberation. The various leaching methods available vary in the means by which gold/solution contact and solid/liquid separation are achieved. The essential difference between heap or vat leaching techniques and those involving agitation of a slurry is dependence on percolation for effective gold/solution contact. The most significant factor preventing uniform percolation is the presence of fines or clays. The quantity and character of the fines fraction is ore type dependent and may result from crushing, degradation during stacking or leaching, or the natural size distribution of the ore. The problems associated with fines can be aggravated during stacking and preparation of the heap. Segregation during stacking can result in concentration of fine particles at the centre of heaps. Further concentration of fines may also occur during irrigation by the movement of the fine particles with the solution. The end result is that the areas in which fines are concentrated become areas of low permeability. The contact between leach solution and the ore in such areas is, at best, slowed down dramatically and, in some cases, prevented altogether. The consequences of this phenomena are slow leaching and a reduction in recovery. The conventional solution to this problem is well known. Agglomeration of ore prior to heap leaching is practised widely. The effect of agglomeration is to immobilise the fines by causing them to adhere either to each other or to larger ore particles. The net effect is that the ore behaves as if no fines were present. The use of agglomeration is limited only by its cost, the most significant components of which are the cost of binding agent, commonly cement, and the capital cost of the agglomerating equipment.

Jan 1, 1995

By Werner A. Ruemmele

Eisenhower Memorial Tunnel, called Straight Creek Tunnel during construction is located 60 miles west of Denver, Colorado at 11, 160 ft. elevation. It is 8, 510 feet long, and carries two lanes of 1-70 traffic under the Continental Divide. This paper describes improvements and changes made in construction methods for utilities, concrete lining, ceiling, wall covering and paving to allow maximum offsite fabrication and activity overlap resulting in a one-year faster completion for traffic. The substantial changes proposed on a design-and-construct basis by the contractor and put into effect after State approval were: 1. Substitution of ductile iron and thick-wall P.V. C. pipes for clay pipes allowing placement and operation before hole-thru. 2. Outside pre-assembly of large rebar mats, using a novel tension-splice with cable clamps. 3. Arch concrete placement method modified to make 4, 322 ft. of lining in 10 weeks possible. 4. Safety barriers precast and epoxy coated offsite instead of cast-in-place and tile faced. 5. Prestressed hollow ceiling slabs with porcelainenamel coated steel sheets assembled offsite, instead of in-place glazed tile and in-place cast concrete ceiling. 6. Glazed tile wall panels 8 ft. long by 11 ft. high assembled off site and erected using vacuum pad mounted on special lift. 7. Asphalt paving while other work proceeded, instead of reinforced concrete slab and asphalt overlay. Work started in January 1968, but advance came to a one-year standstill for major structural redesign and negotiations of a new agreement during 1970. Using multiple drift construction followed by top-heading and bench excavation, it then progressed to hole-thru in July 1972. As a result of art 18-month overlap of activities the tunnel was opened for traffic only eight months later in March 1973. Gibbons and Reed Company of Salt Lake City, Utah sponsored the joint Venture of Al Johnson-Gibbons and Reed-Western Paving-Kemper during 1971, 1972, and 1973. The tunnel was the subject of a previous paper delivered at the RETC '72 in Chicago by R. C. Hopper, T. A. Lang, and A. A. Mathews, describing geology, unusually severe structural loading and multiple-drift tunnel excavation.

Jan 1, 1974

By Don U. Deere

The tunnel boring machine (TBM) can be a magnificent tunneling device under optimal rock conditions. Such ideal conditions would include good Rock Material Characteristics (compact, uniform; low to medium strength, hardness, and abrasiveness); good Rock Mass Characteristics (few joints and shears; unweathered); and good Geologic Environmental Characteristics (above groundwater level and moderate in-situ stress). Such idealized rock conditions would eliminate support problems, fallout at face and grippers, frequent cutter changes, and water problems. Daily advance rates of 50 m would be commonplace. Unfortunately, nature seldom provides the ideal geologic characteristics. The challenge to the geologist, machine manufacturer, and contractor is to provide equipment and procedures to best handle the adverse geologic features, once identified.

Jan 1, 1981

By Jack K. Lemley

This paper will provide an update of the Channel Tunnel Project including a discussion of the overall legal structure and management organisation. It is important to understand the mission that TML, as a design/build contractor, has undertaken and how the various interfaces have evolved between the other entities involved in the project. The paper will describe the evolution of the management organisation and the approach to completion of our contract, recapping the historic events and moving into a projection of how we will manage the completion of this very large transportation system.

Jan 1, 1991

By Andrew T. MacKenzie, Paul A. Rantala

Predictive pastefill rheology (flow characteristic), models have long challenged pastefill practitioners. While the methodology and practicality of recipe formulation is attainable in most locals, the remaining challenge has been to devise a predictive mathematical or empirical model of paste flow characteristics. Flow phenomenon can now be assigned mathematical and physical basis. The authors herein disclose physical and mathematical methods that demonstrate how operators could proceed when designing reliable pastefill systems. Knowledge presented will allow users flexibility in adjusting flow-rates. Laboratory data shows stiff pastefill delivery design can be derived through mathematical relationships of particle size, material characteristics and pipe diameter.

Jan 1, 2001

By P. Worley

Installation of UP& Is monitoring system was planned to be completed in three stages: Environmental Monitoring, ConveyorBelt Interface, and Power Distribution Interface. With Phases 1 and 2 completed and Phase 3 initiated, massive amounts of valuable information have been obtained. From this information, many benefits where recognized and the decision was made to expand the system. This provided monitoring and control capabilities in a variety of new applications from ventilation fan and pump interface to innovative installations such as ground control monitoring. All current uses as well as future plans for expansion and data manipulation will be discussed.

Jan 1, 1990

By Eugene E. Brucker

In recent years, there has been increased interest in construction problems presented by karst topography. Twenty-five years ago, karst areas were by-passed for development. Today, the high cost of land and population pressures are requiring utilization of karst areas. Areas exhibiting karst features can be satisfactorily developed so that construction can proceed in a normal manner; or the areas may be left undeveloped and the underground drainage system abused by improper use causing or contributing to structural collapse, excessive erosion, and a grave threat to the stability of land development and the environment. The term "karst" is a comprehensive term applied to areas underlain by soluble rock that possess a topography formed chiefly by the dissolving of rock and the diversion of surface waters to underground routes. There are four features which contribute to the maximum development of karst. 1. A soluble rock, preferably limestone, must be present at or near the surface of the ground. Occasionally, dolomite will suffice.

Jan 1, 1970

By L. Lacerda

Shotcrete is widely accepted as an indispensable form of ground control around the world. Other Surface Support Liners such as mesh have been around as long as shotcrete while other Thin Support Liners (TSLs) have been introduced in recent decades. TSLs, however, have yet to replace shotcrete in many applications believed to be “perfect” for them. On the other hand, some recently introduced technologies may be on the brink of meeting most surface rock support requirements economically and safely. This paper will discuss rockfall statistics, small rockfall prevention and compare different surface support liners such as mesh, shotcrete and TSLs. Additionally, a shaft sinking TSL application example will be presented.

Jan 1, 2004

By Gregory Witte

This paper will explore the technology behind and applications of smart motor control centers (MCCs) being used today in mineral processing facilities. The two technologies to be discussed are solid-state motor controllers that can be installed in MCCs and the complementary digital communication networks that can transmit operational parameters of the solid-state devices to the supervisory system. The toughness and reliability of solid-state technologies have led to a dramatic increase in their usage throughout the mining industry. Products such as solid-state motor protectors, controllers, and variable frequency drives have demonstrated greater flexibility and performance in a variety of applications than their electromechanical and mechanical counterparts. The three key trends apparent in the solid-state devices are: 1. A shift to smaller, smarter, more integrated devices, which allows a single solid-state device to serve the purpose of multiple electromechanical devices but in a much smaller form factor. 2. Distribution of control logic in motor control devices rather than conveyed through a hard wired connection to a central automation system. 3. Embedded network communication that allows supervisory systems to have an expanded view into critical loads and sensors. In applications, the use of smart actuators and sensors with integral local intelligence and communication allow a supervisory controller to send high level commands and let the smart device coordinate its own work The ability of smart field devices to return noncontrolled, nonpoled information opens a whole array of new capabilities for preventive maintenance and diagnostics and forms the basis for an effective motor management program. The smart motor control devices this paper will explore are the smart motor protectors (SMP), smart motor controllers (SMC), and variable frequency drives (VFD).

Jan 1, 2000

By J. M. Manka

American mining companies operate many drum hoists, hoisting from varying depths with varying payloads. This paper reviews the procedure for selecting optimum wire rope constructions for existing hoisting installations. Selection for proposed installations, along with recommended hoisting parameters, is also discussed. To achieve optimum rope performance, preventive and corrective maintenance procedures are required and are reviewed here, along with examples of rope problems and their causes.

Jan 1, 1993

By W. E. L. Minter

The most important Witwatersrand gold placers occur on extensive unconformity paleosulfaces that were produced during protracted periods of fluvial degradation. The erosional etches on what was generally unlithified sub-strate indicate that low sinuosity erosion patterns prevailed. The transport systems were dominantly braided fluvial with a minor debris-flow component. The placer sediments were non-cohesive sands and gravels. They were evidently transported by fluctuating, yet perennial, discharges across extensive, low relief braid plains, not far from littoral environments. Progress made in understanding heavy mineral transport processes now emphasizes the importance that selective entrainment probably had in producing concentrations. Cognizance that these characteristics are not unique to the Witwatersrand should be taken into account when designing exploration models.

Jan 1, 1991

By R. T. Swindeman

"INTRODUCTION This paper will discuss the topics in the recently released Conveyor Equipment Manufacturers Association’s (CEMA) Belt Conveyors for Bulk Materials, 7th edition, that deal with safety and maintenance. The most effective way to improve conveyor safety is through designing out hazards in the earliest stages of a project. When the safest way to perform maintenance is also the easiest, mechanics will naturally take the obvious and least hazardous approach. IMPORTANCE OF ACCESS Studies have shown that mechanics spend almost one-third of their time accessing the components to be serviced and approximately 25% of all fatal conveyor accidents occur during maintenance1. Chapter 2 of Belt Conveyors for Bulk Materials deals with design considerations. In Chapter 2 there are recommendations for access at the various sections of a typical conveyor for cleaning, inspection and maintenance. While, in some cases, providing access will increase the cost of the conveyor system there can be significant paybacks in reduced injuries, faster maintenance and easier cleaning. Piping and Conduit One of the significant recommendations in Chapter 2 for access is to restrict the mounting of piping and conduit to the conveyor structure in the Loading and Discharge zones of a conveyor. Piping and conduit are more permanent fixtures than maintainable components and should be located out of the way of components needing frequent maintenance. If electricians and pipe fitters are given convenient locations to make their runs they will natural use them. Flexible conduit and hoses can be used to connect to components from pipe racks and cable trays which further enhances maintenance. Access for Cleaning Another critical aspect of access is for cleaning. Approximately 33% of all fatal conveyor accidents occur while cleaning spillage and carryback under and around conveyors2. In the loading zone having sufficient height under the conveyor for cleaning increases the cleaning interval and allows for safer cleaning. In the discharge zone having adequate access for belt cleaning installation has a direct effect on the ability to install a proper cleaning system and perform maintenance."

Jan 1, 2015

By M. David Monroe

Getting the best match between truck and haul road requires examining the cost effects of many factors. Most mines use a bottom line measure based on cost per ton of material moved. This measure focuses on the two components of truck haulage cost per ton: productivity (or performance) and operating cost. For specific tasks, productivity can be measured or predicted using either field measurement or modeling. Individual tasks can be combined to provide a larger scale, longer term net figure for total mine output. True cost is more difficult to capture. Factors are time- and task-oriented and can be influenced by a summation of factors over a truck's lifetime. For example, "allocated" costs, such as owning (depreciation) and some repair costs, are spread over long periods. Items such as fuel and tires can be tied more directly to certain tasks. This article focuses on the more direct, task-oriented factors that affect truck productivity and cost. Major factors The relationship of haul roads and trucks means that each must be examined separately to isolate the most important factors affecting performance and cost. There are many factors but the most important are:

Jan 1, 1992

By Julia R. Budden

The role of bacterial oxidation in the mining industry is becoming more widely accepted. Western Australia has accepted the technology as a pretreatment for refractory gold concentrates more readily than most. The third of such plants has been completed at the Y ouanmi Gold Mine. This is situated approxi­mately 500 kilometres north east of Perth, in the Yilgarn mineral field. Y ouanmi concentrates are produced from underground ore and contain arsenopyrite and pyrite as the main sulphide miner­als. Refractory gold from this deposit is generally associated with the arsenopyrite portion of the material. Gold Mines of Australia Ltd ("GMA") initiated pilot scale testing at the BacTech premises in November 1993. The decision by GMA to use BacTech's technology was announced in February 1994. Design and construction commenced at this time. Bacterial growth on site was initiated in July 1994 and continuous opera­tion began in the October. Concentrate was added at 0.5 tonnes per hour and this has increased to 1 tonne per hour.

Jan 1, 1995

By Bryce T. Tripp

Utah's abundant industrial rock-and-mineral resources support a relatively small but important sector of the State's economy. In 1983, six of the top 10 nonfuel mineral commodities (by value) were industrial commodities. Portland cement was ranked fourth, potash fifth, halite sixth, phosphate seventh, construction sand and gravel eighth, and lime tenth. Portland cement was produced by three operators, principally from the Jurassic Twin Creek Limestone. Potash was produced by three companies from Pennsylvanian beds in the Paradox Basin, surface brine of the Great Salt Lake, and subsurface brines of the Great Salt Lake Desert. Halite was produced by eight operators, primarily from surface brine of the Great Salt Lake. Additional production came from salt beds in the Jurassic Arapien Shale, solution mining of the Pennsylvanian Paradox Formation of the Hermosa Group, and subsurface brines of the Paradox Basin. Phosphate was mined by one company from the Permian Meade Peak Phosphatic Shale Member of the Park City Formation. Construction sand and gravel were produced by dozens of operators, primarily from Quaternary Lake Bonneville beach and nearshore deposits. Lime was produced by four operators from Paleozoic formations in the Basin and Range physiographic province of Utah. The future production of these and other industrial commodities, though individually uncertain, is expected to increase gradually as a group. Factors favorable for the future of the industrial commodities industry in Utah include large to almost unlimited resources for the major commodities, a healthy projected population growth, an abundant local supply of relatively inexpensive energy from coal and natural gas, and a favorable corporate tax structure and business climate.

Jan 1, 1987

By Terry McNulty

There are many potential pitfalls in the commercialization of innovative technology, and the failures often are remembered longer than the successes, thereby serving as deterrents to subsequent attempts. Given the dependence of the mineral industry's future on effective innovation, it is essential that we understand the causes of failure. Case histories are presented and the out- comes are analyzed in terms of the driving forces for innovation and the steps taken during development. Industry's current attitude toward and capacity for technological innovation are discussed, and a methodology is suggested for predicting successful innovation.

Jan 1, 1998

By Fathi Habashi

ION FLOTATION was introduced by F. Sebba in 1959. This technique permits the recovery of metal ions from solution through the introduction of an appropriate cationic or anionic surface-active agent into the solution. The surface-active agent, called a collector, is added in stoichiometric amounts in relation to the metal content of the solution. It reacts with the metal ion to form an insoluble soap, and is levitated to the surface by gentle bubbling of air to form a foam which collapses into an insoluble scum. The optimum conditions for the ion flotation with soaps of C10-16, fatty acids are shown in Table 15-1. Baarson and Ray (1965) found that once the metal was completely precipitated as the hydroxide, as little as one hundredth the stoichiometric amount of the collector was required to cause complete flotation of the [ ]

Jan 1, 1970

By S. S. Peng, Luo. Y.

In a shearer longwall mining operation, the longwall hits are responsible for breaking into and chipping the broken coal blocks away from the coal face. However, underground observations found that the bits being used were working under various degrees of wear. This wear can be reduced by using better-designed longwall bits and by properly selecting shearer operating parameters. A computer program was developed to simulate the performance of the longwall bits. The information required by the program are the shape of the bit head, the installation of the bits on the drum and the operation parameters. Through the simulations, the main factors affecting the bit-wearing process are identified. Suggestions are also made for improving the design of the longwall bits.

Jan 1, 1998

By Antonieta Middea, Rupen Adamian, Fernando F. Lins

This work presents the results obtained with aggregation of fine talc (-19 m), a naturally hydrophobic mineral, in the presence of KC1 solutions. The classical DLVO theory describes well the aggregation of talc in dilute KC1 solutions. Beyond 1 M KCI we have found indications that a non-DLVO interparticles force is operative, say an hydration (repulsive) force. This structural force could be responsible for the unexpected re-dispersion of talc suspension. However, no repulsive force (depression) has been observed in salt flotation of talc at higher ionic strength, up to 3 MKCI.

Jan 1, 1995

By V. Carabias-Hütter, A. J. Basu

The paper aims at promoting sustainability assessment and reporting into practice using a globally acceptable set of guidelines and a common framework for internal and external reporting at a project/site level. Indicators are used for measuring performance, and this paper addresses development and implementation of performance indicators for sustainability assessment and reporting at local as well as global levels. The selection of a proper set of indicators is a challenging task. The indicators selected should provide the expected information for making right decisions. Relevant and credible sustainability reporting supported by a consistent performance indicator system can be the starting point for benchmarking environmental and social performance for the natural resources sector.

Jan 1, 2004