Search Documents

By David G. Abbott, Frank Coluccio

This paper will discuss the construction of nearly 165 m (540 ft) of 3.5. m (138 in) o.d. reinforced concrete pipe to replace an existing utilidor under the Duwamish River in Seattle, Wash. The project required that two 27.4 m (90 ft) deep shafts be installed for use as jacking and reception shafts during the tunneling operation, and permanent vaults once completed. Soil conditions to be excavated consisted of soft saturated sand and silt with a 21.3 m (70 ft) water head. This required the shafts to be constructed using ground freezing techniques and the tunnel installed by pipe jacking, using a Mechanical Earth Pressure Counter Balance (MEPCB) slurry shield. The original utilidor was constructed between 1924 and 1925, and has since been deliberately flooded because it is considered to be structurally unsound.

Jan 1, 1995

By N. Djordjevic

The vibration energy that travels beyond the zone of rock breakage is wasted - all it does is cause damage and annoyance. Under favorable geologic conditions, this energy may travel many kilometers before it finally drops bellow the background noise level. This has forced the introduction of more restrictive limits to the allowable vibration levels. To maintain the profitability of a mine or quarry and to comply with environmental protection legislation, blasting needs to be performed in a more predictable way that will ensure that the final results are optimal in both mining and environmental terms. Minimization of ground and induced structural vibration is, therefore, a matter of good blasting practice - not just an attempt to avoid complaints from neighbors. A new approach to blast vibration minimization is presented. The method utilizes the existence of the local minimums in the frequency spectrum of single-hole blast vibration. The results are presented as a delay map showing maximum ground or structural vibration velocity for many combinations of interhole and interrow delays. A blast engineer can use this map to select an optimal combination of delays that will produce a low vibration velocity at a selected location and, at the same time, will be acceptable from the point of view fragmentation or muck pile shape.

Jan 1, 1997

By Milton E. Wadsworth, Jeffrey S. Thompson

The effect of an activator on gold dissolution in clear solution is examined using a rotating disk gold electrode. Steady state polarization curves for anodic dissolution of gold and cathodic reduction of oxygen indicate that the dissolution rate increases in the presence of the activator. The activator enhances gold disso­lution under standard cyanidation conditions; however, optimum activator concentration at the maximum dissolution rate is a function of the cyanide level. In the presence of an activator, the gold dissolution mechanism is controlled by surface kinetics and may be explained by a metal dissolution over-potential model. The dissolution rate with activator is higher than the dissolution rate at a higher cyanide concentration but without activator. The dissolution rate measurements indicate that 3 PPM of activator in a 500 PPM NaCN solution provides a higher dissolution rate than 1000 PPM NaCN alone. Activator technology may be a cost-effective means to reduce cyanide concentration.

Jan 1, 1998

By K. P. Unrug, E. Thompson, S. Nandy

The method of coal pillar design involves primarily two aspects: the geometry of the pillar and the strength of the coal. However, the strength of the coal has to be emphasized with respect to the entire pillar dimension rather than isolated strength values of coal samples taken and measured from different locations. As of now, the presently applied pillar design systems do not specify clearly what the coal sample strength really represents. The intention of this paper is to introduce the concept of seam strength as opposed to the current practice of using coal strength as a prime design criteria in the formulation of pillar calculations. Seams are most often composed of multiple layers of coal, partings, and bone in various configurations, changing within the vertical section of the seam even in relatively close locations. The difference in strength between the weakest and strongest component of the coal seam could be as much as five times or more. An experimental approach based on multiple uniaxial compressive strength tests performed on coal samples from the Coalburg and Warfield seams from eastern Kentucky was undertaken. Analysis of the results led to the conclusion that for pillar dimension calculations, both the weighted mean of the seam strength and the strength of the weakest stratum should be considered, rather than the relatively vague aspect of coal strength. The design of pillar dimensions based on the aforemen¬tioned criteria should assure a more realistic design performance.

Jan 1, 1987

By D. M. Milne, H. H. Kanduth

INTRODUCTION The past few years has seen an increased interest in the determination of statistically valid properties of a rock mass. The increased use of computer modelling for the study of rock excavation behaviour has created a need for upper and lower statistical bounds for the properties of a rock mass being modelled. Obviously, to determine the statistical properties of a large volume of rock, many samples must be tested - an expensive proposition when using conventional testing facilities and procedures. As a result of high costs per sample, sufficient tests for statistically valid results are rarely done. In an effort to reduce both sample preparation and test facility costs, an instrument called the Bemek Advanced Rock Tester (BRT) was developed in Sweden. With a total weight of approx. 35 kg, the BRT is portable and sells at a small fraction of the cost of a conventional testing machine. It is comprised of a small 65 KN loading frame with attachments for a variety of tests (see Table 1) , a hand operated hydraulic pump, an electronic balancing unit and a programmable microprocessor. The microprocessor is capable of storing data, performing arithmetic operation on, and printing signals from, a transducer and two strain gauges. A detailed description of the apparatus is given by G. Swan et al. (1). The proposed test strategy involves first a 3-point flexure test on a notched core specimen, followed by a 4-point flexure test on the separated specimen halves. Finally, point load and Brazilian tests can be carried out on the quarter parts of the original specimen. Thus specimen preparation is kept to a minimum. These and other perceived advantages have prompted the purchase of this machine and an evaluation of its suitability to provide data on mechanical properties of intact rock for numerical modelling and rock mechanics design at Noranda's underground mines. Details of its performance evaluation and experiences with the unit are discussed in the following sections. [ ] INITIAL OPERATING EXPERIENCE During the commissioning stage the BRT had, or developed, a series of problems, some of which seriously affected its operation. Below are some examples. Poor documentation was the most serious problem encountered. Confusing instructions for the 4-point bend test installation and its microprocessor programing, as well as poor and ambiguous information on the calculation of gauge factors, are some of the difficulties which had to be overcome. Meehan~cal problems occurred, including failure of the hydraulic pump, as well as electronic difficulties with the microprocessor. Other problems with the printer, requiring its replaceqent, were fortunately covered under warranty.

Jan 1, 1986

By Cherie M. Tilley

The Stillwater Mining Company has acquired a Tunnel Boring Machine to expedite the mine development operations at its Stillwater Mine. The machine purchased by Stillwater was previously owned by Melbourne Metropolitan Board of Works, Melbourne, Australia. The machine was manufactured by Robbins Co. of Kent, Washington. The Stillwater Mine has an extensive system of footwall laterals which are required by the mine development scheme. The initial mine plan called for in excess of 30,500 linear meters (100,000 linear feet) of footwall lateral drifts at a cross section of approximately 3.0 meters in width by 3.75 meters in height (10 feet x 12 feet). A Tunnel Boring Machine was selected for this work. The Robbins machine number is 146-193. This machine is approximately 4 meters (13 feet 5 inches) in diameter. The machine was modified extensively prior to commencing operation at the Stillwater Mine.

Jan 1, 1989

By Rodney H. Sergent

After being forgotten or ignored for nearly 100 years, the ability of bromine chemistry to extract gold from ore has been rediscovered. While bromine chemistry is similar to chlorine, there are some important differences. Bromine in its elemental form is a dense, fuming, red liquid. Elemental chlorine is a gas and requires a substantial amount of equipment to handle, store and deliver to solution. Bromine has an advantage in its ability to rapidly and completely oxidize heavy metals to water soluble halide salts. The first patent for use of bromine chemistry for gold extraction was issued in 1881 (1). By 1895, work done in Colorado concluded well roasted ores required approximately 1-1/2 lbs/ton of elemental bromine for superior extraction of metals (2)). At that time, bromine was deemed to be cost effective vs. chlorine even though it was more expensive on a pound basis than chlorine. The advent of cyanide technology virtually eliminated both chlorine and bromine from consideration for leaching of ores. Cyanide was so inexpensive that it made deposits requiring unique technologies unattractive for mining. Only since the deregulation of gold price has bromine/chlorine technology been considered for those ores not amenable to cyanide. While chlorine has found its way into the pretreatment steps, bromine is just beginning to realize its niche in the marketplace.

Jan 1, 1998

By J. J. Robertson, D. M. Polizzotti

Cement is used as an established agglomerating agent in gold heap leaching operations to maintain heap permeability and prevent migration of fines. In addition to agglomeration, cement provides protective alkalinity control. However, the amount of cement needed for agglomeration is usually very different from the amount necessary for pH control. As a result, cement is usually added in excess. Overdose of cement can result in reduced gold recovery and/or lengthy detoxification. Betz Laboratories has identified polymeric agents that provide the benefits of cement without negatively impacting gold recovery when used alone or with lime. Independent laboratory tests also strongly suggest that the polymer/lime system can significantly reduce heap detoxification time.

Jan 1, 1992

By P. Venkatraman, F. S. Knoll, W. S. Kow

Froth flotation is the most widely used technique for cleaning fine coal. This practice may change, however, with the development of enhanced gravity concentrators such as the Mozley Multi- Gravity Separator (MGS). The MGS is a flowing-film concentrator that utilizes centrifugal forces to improve the separation of flotation-size particles. In the present work, a pilot-scale test program was conducted to examine the effects of feed rate, feed solids content, wash water flow rate and drum rotation speed on the performance of the MGS. The test results indicate that the MGS effectively rejects high-density minerals such as pyrite, while ultrafine ash-forming minerals are removed less efficiently. A major advantage of the MGS is that high separation efficiencies can be realized without additional grinding, flotation reagents or heavy media. This article describes the working principles of the MGS and presents data obtained from recent pilot-scale test work.

Jan 1, 1995

By Stewart R. Wallace

In the spring of 1959 while visiting the offices of the US Geological Survey (USGS) in the Denver Federal Center, I had a chance encounter with Paul Theobold, a former but, at that time, casual associate. Paul mentioned to me the results of his work on stream sediment geochemistry (Theobold and Thompson, 1959). Using panned concentrates, Theobold and Thompson had discovered a tungsten anomaly in Clear Creek and followed it upstream to its source on Woods Creek, a small tributary to the West Fork of Clear Creek. The specific source was a debris cone about 0.8 km (0.5 mile) upstream from the mine yard at the Urad molybdenite deposit. Because of the genetic and zonal association of tungsten and molybdenum at Climax, I found this very interesting. Accordingly, I related this information to Robert Henderson, general manager of western operations for Climax, and asked his permission to do some follow-up work. He, in turn, telephoned Frank Coolbaugh, the president of Amax, telling him of my interest and saying that, "Climax would take care of it." On my first visit to Urad, my companions (Dave Jonson, Bruce MacKenzie, and Dick Baker) and I were confronted by a "Cousin Jack" caretaker who made up for his diminutive stature by a "pistolover" that hung down almost to his knee and by a watchdog that was one-half wolf and one-half mean sled dog. We retreated discretely to Clear Creek and then climbed up the "back" side of Red Mountain by separate routes, across the ridge crest, and part of the way down the "front" side, sampling as we went. Although much of the ground was covered with snow, we found lots of puzzling but friendly looking rocks and the geochemical results were interesting. A geologic map of central Colorado showing the location of the Urad-Henderson and Climax deposits is shown in Fig. I.

Jan 1, 1991

By William Mayrsohn

IMTRODUCTION The marketing aspects of a new precious metals property is often not considered until the mine actually begins production. At this point in time it is often too late or too expensive to change the mine's final product and not enough time to do an effective marketing program. MINE PRODUCT The rule for determining the mine's final product: The higher the gold and silver content, the greater return of metal at the lowest post-mining cost. . Dore Bullion: Most advantageous Advantages: - Highest return of metal. - Lowest refining cost per ounce of gold and silver. - Very compact and easy to ship in small quantities. - Easy to assay. - Assays between mine and refiner are comparable. - Melt losses are very small at the refiner. - Outturn of gold and silver 20-30 days for quick cash flow. - Gold/silver refiners can return or purchase metal soon after arrival at a nominal financing cost.

Jan 1, 1987

At present, increasing focus of public perception is placed on the environmental and social benefits, risks and impacts of metals and metal-bearing products. To address these issues, the concept of product stewardship has recently been introduced into the political debate. In this paper, results from a survey of existing environmental and social reporting practice in the copper mining, smelting, refining and fabricating industry are presented. In this context, particular emphasis is placed on the reporting practice regarding products and product performance over the life cycle. In a few companies there has recently been a shift towards adopting product stewardship principles and putting them into action. As part of an ongoing exercise within the Non-Ferrous Consultative Forum on Sustainable Development sponsored by the International Copper Study Group (ICSG) key issues of interest to the non-ferrous metals sector are being addressed. The Forum, for example, has developed a series of principles, criteria and indicators that could form the basis for a voluntary, industry-lead product stewardship scheme. Current achievements and way forward of this product stewardship initiative will be presented.

Jan 1, 2003

By P. N. Eksteen, G. E. Greig

The South African mining industry currently installs about 6 km per month of plastic pipes for conveying compressed air and water. Plastic pipes have a number of desirable properties and are favoured by many mining engineers because of their low mass, which facilitates ease of erection and assembly, and their excellent corrosion resistance and durability. However, they are combustible, and if involved in an underground fire can contribute to the overall toxicity of the combustion gases emitted. Furthermore, plastic pipes have the potential to conduct a fire from one part of a mine to another, and, by so doing, exacerbate an already hazardous situation. The limitations of small scale tests and the need to establish a large facility where underground conditions could be simulated was recognized by the South African mining industry. This paper briefly describes the Industry's full scale fire test facility and presents the conclusions drawn as a result of a number of full scale combustibility tests conducted on pipes manufactured from unplasticized Poly Vinyl Chloride (uPVC) and High Density Polyethylene (HDPE). Based on these findings, some practical solutions to prevent the spread of fire along the length of pipe columns of various pipe diameters and suspension configurations are presented. Recently some new and exciting developments in the field of intumescent coatings have occurred which are proving effective in minimizing the incidence of fire underground on South African mines. The potential benefits of these coatings are briefly discussed. INTRODUCTION Plastic pipes used underground on mines are predominantly in the form of protective cladding on insulated chilled water pipes and as service pipes for the conveying of water and compressed air to the workings. Plastic pipes have found wide use in the aggressive environmental conditions encountered underground due to their favourable properties relative to steel; these include being lightweight, easily installed and virtually immune to corrosion. However, plastic pipes are inherently combustible and can contribute to the overall hazard in three ways: (i) they are easily ignitable and can provide the initial fuel for a fire. (ii) once ignited, they can propagate a fire along their length and by so doing ignite other combustibles in their path, thereby contributing significantly to the overall conflagration. (iii) they can contribute to the overall heat, smoke and toxic gas emissions from a fire. While conscious of the value of small scale fire tests, the South African mining industry recognized the need for full scale testing to determine the combustion characteristics of plastic pipes under conditions closely approximating those underground and, as a consequence, a full scale fire tunnel test facility was commissioned with the objective of being able to (a), accurately evaluate the potential hazard of the various types of the plastic pipes found in mines, (b) use this information to suggest suitable fire engineering practices to minimize the hazard and (c), to practically verify the efficacy of the practices suggested. THE FIRE TUNNEL The fire tunnel is situated on a mine in the Western Transvaal and is 40 m long with a cross section of 3 m x 3 m which is typical of many haulages currently in use in South African gold mines. The ventilation drawn through the tunnel is provided by a 110 kW centrifugal exhaust fan and air velocities can be varied from 0 to a maximum of 5,8 m/s.

Jan 1, 1993

By Wilson I. L. Lim, Jonathan J. Campbell, Luis A. Tondo

An important issue in the use of high pressure grinding rolls when grinding ores is wear of the rolls. Due to the abrasive nature of the ores, significant wear rates have typically occurred. Attempts to address the wear problem require a better understanding of the wear mechanisms. A probable wear mechanism is the abrasion of the rolls surface due to extrusion of the compacted material as it leaves the rolls. This paper presents the results of a study on a number of ores to examine the extent of extrusion that occurs. The study involved laboratory, pilot and full-scale high pressure grinding rolls. The effect of variations in parameters such as grinding pressure, rolls speed, initial gap settings, feed topsize and moisture was investigated. The results indicate that extrusion increases with increasing grinding pressure and rolls diameter, while the use of studded or profiled rolls significantly reduces the extrusion effect compared to smooth rolls. It was also found that rolls speed and feed moisture can have significant effect on extrusion, depending on the material.

Jan 1, 1998

By P. Anciaux

The EUs? manufacturing and construction industries are vital to Europe?s economy. They rely heavily on a steady supply of materials which meet appropriate quality criteria and are available at a competitive price. The steadily rising global demand for (non-energy) raw materials due to increasing consumption in upcoming economies such as China, India and Brazil, is in some cases leading to rapid price increases, but also supply disruptions which affect the European industry chain. These considerations are at the basis of new policy initiatives that are being prepared by Enterprise and Industry Directorate-General in relation to the competitiveness of the European metals industry. Over the last year the raw materials supply issue has increasingly become the topic of de-bate among various stakeholders. In July 2006 the European Economic and Social Committee adopted an opinion on risks and problems associated with the supply of raw materials to European industry. It is therefore important to identify and analyse the future needs for European industry, the possible constraints and impacts on its competitiveness. The raw materials supply issue should also be looked at from the view-point of the EU extractive industry, which plays an important role in supplying raw materials to the downstream industries and which faces very specific challenges. Within the Enterprise and Industry Directorate-General the different factors that influence the competitiveness of the non-energy extractive industry are being assessed, in order to help identify policies and actions which could contribute to and enhance the competitiveness of the industry.

Jan 1, 2007

By Steve McIntosh

Restoration of a wetland which was initially disturbed at the turn­of-the-century will be undertaken to compensate for the temporary loss of wetlands associated with future mining operations. The proposed mitigation area exhibits xeric conditions as a result of past dredging and gravel mining operations which had the effect of lowering the flood plain surface and wasting the fine surface sediments. Together these mining activities resulted in complete alteration of the surface and subsurface water systems. Water which had inundated the soil profile, now flows on the basalt bedrock, surfacing only for a relatively short time during high flow periods. The conventional approach to wetland restoration in this type of area is to remove surface material in an attempt to bring the surface nearer to the underground water. These operations would require the removal and redistribution of large quantities of gravel, cobbles and boulders and the attendant destruction of existing wetland areas. Rather than lowering the surface elevation to the water level, the mitigation plan conceptualized for this project involves forcing the water to the surface by creating subsurface ponds behind four impermeable barriers. The barriers will extend vertically from the bedrock to the surface. Surface berms will be constructed along the length of each groundwater barrier to enhance sediment deposition and encourage the development of wetland vegetation. This is the least expensive and least invasive method of creating a wetland which will remain saturated to the requisite degree and for the amount of time required for classification as a wetland as defined by the 1989 Federal Manual for Identifying and Delineating Jurisdictional Wetlands.

Jan 1, 1993

In April 2012, work started on one of the most ambitious construction projects of Austria?s ÖBB-Infrastruktur AG ? the New Semmering Base Tunnel. Scheduled for completion in 2024, the 27.3 km (17 mile) tunnel through the Semmering range will cut the journey time on the south railway connecting Lower Austria and Styria. Before con-struction can begin at the entrance portal and tunnel bores, the work concentrates on the above ground sections with the clearance and excavation of the entrance ramp site. The slope is currently being excavated by the Baubeteiligungsge-sellschaft m.b.H. BBG-GRAZ. The cut face is shored up with shotcrete and permanent self-drilling anchors produced by Minova MAI, an economical bolting solution for softer rock formations. After completing the surface construction work, the twin-bore, single-track tunnel will be cut through the Semmering by conventional and continuous excavation beginning in 2015. Once completed, the New Semmering Base Tunnel will be one of the longest rail tunnels in Austria. It will act as a vital link on the route crossing Europe?s heartland from Northern Germany to Italy, which currently has to climb the steep Semmering pass between Gloggnitz and Mürzzuschlag on a historic mountain railway recognized as one of the UNESCO World Heritage sites. The old route imposes considerable limitations on heavy freight trans-port, and passenger trains have to slow down to a speed of around 50 kph (31 mph). The New Semmering Base Tunnel will bypass this bottleneck and cut 30 minutes off the journey time between Vienna and Graz. It represents a particular advantage for freight traffic, since the new route?s minimal incline of 8.4 percent removes all obstacles for even heavy freight trains.

Jan 1, 2013

By Paul C. Schmall, Arthur B. Corwin, Hugh S. Lacy, Derek Maishman

For reasons of hydraulic design and constructability, water supply tunnel systems are often located relatively deep, in competent rock. Where the rock lies below a thick cover of water bearing soils, artificial ground freezing offers a low risk, cost-effective method of constructing access shafts. Several examples, in Kansas City, MO and in Brooklyn and Queens, NY, illustrate the use of freezing to provide structural support and ground water exclusion. In the case histories presented, the shafts range from 6m to 12m (20 to 40 ft) in diameter and soils vary from clays to boulder beds with depths in excess of 73m (240 ft) to competent bedrock. Where tunnels for infrastructure are designed to be driven in rock, vertical access may encounter a considerable thickness of overburden soils with groundwater. In such cases, shaft sinking problems are analogous to those confronted by mining engineers over 100 years ago. At that time, newly developed refrigeration machines were set to freeze the ground water and stabilize running sands. Although modern technology has refined our efforts, the basic features of the ground freezing to be described here are the same as those used in the last century. Vertical holes drilled on a circle surrounding the shaft site are equipped with leak-free steelpipes through which a refrigerated brine is circulated. In this manner, a frozen cylinder, seated in rock, is formed when the earth freezes between adjacent pipes. Shaft excavations take place inside a self-supporting, ground-water excluding structure. For mines, no better method of sinking production shafts through deepwater-bearing ground has yet been established. Indeed, major deposits of coal, potash, and salt would have remained inaccessible to this day were it not for the continued use of artificial ground freezing. If mine shaft freezing became relatively commonplace, early applications to civil engineering were few. Mussche and Waddington (1946) mention only five projects between 1892 and 1935; three of these relate to subway or vehicular tunnels in Paris, Antwerp, and (the most extensive) at five locations of the Moscow Metropolitan Railway development. In the United States, the method was used to spectacular effect in 1936, freezing about 3,000 cubic yards of silt to stop a slide

Jan 1, 1999

By S. Luning

In the nineties the gold sector in Burkina became subject to internationally prescribed liberalization policies. The national state is at present only one of many players. Who are these players, and how are they involved with one another in organizing goldmining activities and prospects in Burkina? One mining site serves as a case to study the scope of players and the types of authorities they build upon in governing gold sites. What conclusions can be drawn in regard to the present position of the Burkinabe state within this field of governing authorities?

Jan 1, 2007

By K. M. Atencio, T. Pike, S. Forrest

We will introduce the Small Business Liability Relief and Brownfields Revitalization Act, which is an amendment to CERCLA and the types of sites it includes and excludes, especially as related to mine-scarred land. We will also describe the types of available funds, whether they are competitive or not, what entities are eligible to receive them, and how to access them. We will introduce the legislation’s liability provisions; for example, the recently issued interim guidance clarifying some of the conditions that contiguous property owners, bona fide prospective purchasers, or innocent landowners must meet to qualify for the liability limitations provided in the Brownfields Law.

Jan 1, 2004