Search Documents

By David Wilson, T. V. Rao

INTRODUCTION The Alchem trona mine, owned and operated by Allied Chemical Corp., is located approximately 32 km (20 miles) west of the town of Green River, and 8 km (5 miles) north of Interstate 80 in southwest Wyoming. Trona, a naturally occuring sodium sesquicarbonate (NaCO3 • NaHCO3 • 2H2O), is used for the production of sodium carbonate (Na2CO3), commonly known as soda ash. Present annual US consumption of soda ash is approximately 9.07 Mt (10 million st), out of which approximately 7.3 Mt (8 million st) is produced from the Wyoming trona mines. About 44% of soda ash is consumed by the glass industry; 3 % by exports; and the remaining portion by paper, chemical, soap, textile, and nonferrous industries. Allied Chemical operates an underground mine at an average depth of about 488 m (1600 ft). There are three other trona mines in the area operated by FMC Corp., Stauffer Chemical Corp., and Texasgulf Inc. (see Fig. 1). Allied Chemical became interested in southwest Wyoming trona deposits in the early 1940s. Explora¬tion work was begun in 1959 with the acquisition of federal leases. Exploitation of the reserves began in 1968. Two shafts, one 6.1 m (20 ft) and another 3.7 m (12 ft), were completed prior to 1968. The 6.1-m (20-ft) diam service shaft is divided in half by a cur¬tain wall, with one half used for men and material and the other for ventilation as a return air shaft. During the period from 1968 to 1974, the 3.7-m (12-ft) shaft was used as production shaft with two 7.3-t (8-st) skips. Due to the increased demand for soda ash, plant and mine expansions were completed during 1974. Under this expansion, the material handling system capacity was increased by constructing a new 2721-t (3000-st) capacity ore bin, sinking a 6.1-m (20-ft) diam produc¬tion shaft, and installing a friction hoist with two 22.7-t (25-st) skips. The Alchem mine manpower is 484 employees and about 2.3 Mt (2.5 million st) of trona was produced during 1976. Three different mining systems are used at the Alchem mine: conventional, continuous, and longwall. Allied Chemical introduced its first longwall unit in 1973, which was also the first longwall system introduced in the Wyoming trona district. At present, four conventional, seven continuous, and two longwall units are in operation. This equipment is operated in ten production areas. GEOLOGY The bedded trona and trona-halite in the Green River basin of southwestern Wyoming is a major re¬source for the nation. There are 25 beds that exceed 0.9 m (3 ft) in thickness and underlie areas of about 2590 km2 (1000 sq miles). There are other minor beds that range in thickness from 0.3 to 1.2 m (1 to 4 ft). Allied Chemical's Alchem mine is located in bed 17. The trona bed numbering system starts at the lowest elevation and increases upwards. The trona beds are in the Wilkens Peak member of the Green River formation. The Green River formation was deposited in a lake that began in early Eocene as a large body of fresh water, shrank in size and became saline, and then became fresh water again. The sedi¬ment during the saline phase of the lake, which includes the trona beds, is called the Wilkens Peak member. The underlying freshwater lake deposit is called the Tipton member and includes a 25.9-m (85-ft) sand unit which is a high pressure, low permeability aquifer. The over¬lying sediment is called the Laney shale. The Green River formation is underlaid by the Wasatch formation and overlaid by the Bridger formation (see Fig. 2). The structure of the beds in the area of the Allied Chemical mine is mostly postdepositional asymmetrical folds of small amplitude. These folds range in size of 3 to 6.1 m (10 to 20 ft) to as much as 45.7 m (150 ft). The trend of the folds is northwesterly with the north¬east flank of the anticlines having a steep dip and the southwest having gentle dips. Trona bed 17 varies in thickness from 2.4 to 3.4 m (8 to 11 ft) over the 93.2 km2 (36 sq miles) holdings of Allied Chemical and is flat lying except for the rela¬tively minor folding and a negligible regional dip of about 0.017 rad (1°). Trona occurs naturally in several physical forms in the Green River basin, being both massive and crystal¬line. The trona ore in the Alchem mine is a fine-grained massive ore with a compressive strength of approxi-

Jan 1, 1982

By D. M. Bodily, M. D. Deo, E. M. Whitney

Field data from coalbed methane wells indicate a significant variation in composition as a function of flow rate and time. In particular, San Juan Basin wells have displayed an increase in C02 concentration over time. Prediction of gas quality is critical to the economic evaluation of any coalbed project. Previous models have forecast only pressure and production profiles, ignoring compositional variations. In this study a multicomponent model that incorporates binary isotherms for methane and carbon dioxide has been developed. An extended Langmuir isotherm is used for the adsorption representation and a constant separation factor (similar to relative volatilities in distillation) describes the phase distribution of the species. This separation factor depends both on the surface characteristics of the coal and on the adsorbing species. The chromatographic separation equations have been superimposed on Darcy's law flow. The formulation allows decoupling of the pressure and compositional partial differential equations. The equations have been cast in dimensionless form and solved for pressures and compositions. It is observed that the composition of the preferentially adsorbed C02 increases at the wellbore as a function of dimensionless time. The dimensionless time is directly proportional to the real time and coalbed permeability and is inversely proportional to the gas viscosity, coal porosity and the square of the length of the reservoir. As the separation factor increases, the compositional variation increases. This variation in produced C02 concentration is also greater when the initial C02 concentration in the reservoir is higher. A sensitivity study has been performed to identify the effects of important parameters such as isotherm variables and reservoir characteristics on pressure and composition profiles.

Jan 1, 1993

By Chas. E. Shumate

There is assembled here this morning in Chicago the heartland of America, what is undoubtedly the greatest concentration of Technical, Scientific and "CAN DO" knowledge ever assembled in America. The participation in this Conference by the representatives of so many nations is particularly impressive and is a further indication of the importance of the subject matter of this conference which you will be discussing in much detail during the next few days. Another impressive feature of this Conference is the participation of a large segment of the construction industry in whose hands fall the job of building what others design. Also strongly represented is the manufacturing industry whose capability is well known throughout the world. They have the resources to design, develop and manufacture the machines and specialized equipment needed to do any job which the world requires. You should not expect to gain any knowledge from my few remarks this morning as I am undoubtedly the least qualified individual in this room on the highly technical and scientific subjects you will be discussing during these next few days. However, I shall offer a few broad suggestions on subject matter which I trust may generate serious thought during your discussions.

Jan 1, 1997

By Peter Zhang

The immediate roof at the test site consisted of laminated clay shale that is likely to be susceptible to weathering. With seasonal dry-wet cycles in the mine ventilation air, the roof in the intake air would deteriorate and lose integrity over time. In many instances, the weathering-prone roof would gradually scale off piece by piece between bolts and over the entry corners. In some long-term entries, roof weathering could develop up to 2-3 ft deep with columns of bolted roof hanging under the upper intact roof. If wire mesh is used, the roof bags down and reduces the entry height, and the weight of the bagged roof tends to pull the bolts out and poses a safety hazard. An effective measure is always sought to support this type of weak roof that is sensitive to moisture degradation. One solution is to seal the roof shortly after entry development to prevent moisture penetration so that roof integrity can be maintained for the long term. In this application, a polymer-based sealing material was tested in the Rockspring mine for weathering protection and reinforcement. The material is a one-component polymer powder for spray application onto the roof and rib. The sealant material is mixed with water in the spraying nozzle to apply to the roof and rib as a paste. The product sets within 5-10 minutes and forms a membrane as thin as about 1/8-in. The membrane will quickly develop tensile and bonding strength within minutes and completely cure within a few days. Through sealing, bonding and lateral reinforcement, the integrity of the weak roof can be maintained. The material has been tried in a long-term evaluation over several months in a set of main entries in the Rockspring mine owned and operated by Rockspring Development, Inc., affiliate of Foundation Coal. Preliminary evaluation has shown that the material is an effective and economical solution to ensuring the long-term stability of weathering-prone roof.

Jan 1, 2009

By Yuanping Chen, Yihui Zhao, Yunhe Hong

It is important to study the methane transport phenomenon in a longwall panel under descentional ventilation conditions. The gob area is divided into a number of rectangular percolating elements, each of which is connected with its neighbors by leakage passages, so that a network can be formed. Using the mechanics of porous media fluid flow, the mathematical model of air and gas flows can be established. Based on the existing ground pressure theories, the inhomogeneous porosity of the porous media in the gob can be given. Through computer simulation it is found that air pressure and temperature are functions of position. Air density, viscosity, and natural ventilation pressure are functions of temperature, pressure and methane concentration. It is also found that the resistance varies with air density and viscosity. Finally, the calculation results are given to show the differences between ascentional and descentional ventilation methods.

Jan 1, 1991

The importance of factoring mining dilution into the estimation of ore reserves in an open pit mine is discussed. An example that relates the issue of mining dilution to the size of the smallest volumes that can be mined selectively is given. The relationship between the size of the selective mining units (SMUs) and the variance of their average grade is presented. The concept of variance reduction and its use in factoring mining dilution into geostatistical ore reserve estimation is described. An approach to estimate a variance reduction factor by way of conditional simulation is introduced.

Jan 1, 1998

By Fred N. Kissell

INTRODUCTION During the last few years, several new ventilation developments have attracted the interest of mining engi¬neers. Some of these developments are applicable pri¬marily to hard-rock mining, while others are more applicable to coal mining. STOPPINGS Parachute Stopping The parachute stopping is a new type of quick-erect stopping that is intended for temporary use in hard-rock mines (Kissell, Thimons, and Vinson, 1975). As shown in Fig. 1, the stopping is shaped very much like an ordinary parachute, with a canopy of impermeable fabric that is sewn to regularly spaced straps running to a common point. To erect the stopping, the straps are attached to a fixed anchor point such as a roof bolt, and the edge of the canopy is lifted into the moving air¬stream. The airstream pops the parachute canopy into place, and the differential air pressure across the stop¬ping holds it in place, forcing the fabric against the walls, roof, and floor of the mine opening. The principal advantage of the parachute stopping is that it requires only a few minutes to install, making it a great time-saver for emergency use or for day-to¬day changes in ventilation during the production cycle. However, the parachute stopping does require some minimum air velocity to lift it and some minimum differential pressure to hold it in place. For a fabric weighing 0.27 kg/ m2 (8.0 oz per sq yd), the minimum air velocity is about 0.5 m/s (100 fpm), and the mini¬mum differential pressure is about 0.05 kPa [0.2 in. water gage (WG) ]. There is always some air leakage around the stop¬ping, mainly depending upon the extent to which pipes or other obstructions encumber the airway and prevent good sealing. Leakage of a few cubic meters per second (a few thousand cubic feet per minute) can be expected, unless foam is used to improve the seal at the edges of the canopy. Quick-Fix Blowout Stopping The quick-fix blowout stopping is a variation of the parachute stopping (Thimons and Kissell, 1976), and it is used in the proximity of blasting operations. This type of stopping is designed to be blown out easily by the blast forces, and it may be reinstalled quickly and easily. The long high-strength straps of the parachute stopping are replaced by groups of short straps that tear easily. These straps are attached at six equally spaced locations around the perimeter of the canopy. To erect the stopping, one strap of each of the six groups is fastened to the mine wall, roof, and floor by using spads, by setting pins with a powder-actuated gun, or by tying the straps to some firm anchor point. Once the straps have been attached, the differential air pressure across the stopping, which must be at least 0.025 kPa (0.1 in. WG), forces the stopping perimeter against the mine walls, thus creating the air seal. It is the self-sealing feature of this stopping that makes it a significant time-saver. Only a few attachment points are needed; in many cases, four attachment points are sufficient, since the stopping naturally tends to form a seal with the airway surfaces. When nearby produc¬tion blasting exerts excessive forces on the stopping, one or more of the straps tears away from its attachment point, protecting the stronger canopy from damage. Damage-Resistant Brattice The damage-resistant brattice is a stopping that is designed for use in mines such as salt and limestone mines where the differential pressures are low and the roof is relatively flat. As shown in Fig. 2, the damage-resistant brattice consists of a series of brattice panels that are hung vertically and joined by Velcro® connections. When the brattice is subjected to strong blast forces, the Velcro® connection peels apart and allows the panels to open without incurring damage. The Velcro® connections can be resealed by hand within a matter of minutes. Such damage-resistant brattices have withstood the blast effects of 318 kg (700 lb) of ammonium nitrate-fuel oil (ANFO) explosive detonated as close as 91 m (300 ft) from the brattice. Ordinary brattice cloth is used for the panels, with a 51-mm (2-in.) wide strip of Velcro® hooks sewn along one edge of the length, and a 51-mm (2-in.) wide strip of Velcro® pile sewn along the other edge. Both the hooks and the pile are sewn onto the same side of the brattice cloth. The resulting Velcro® seal formed be¬tween adjacent panels is perpendicular to the brattice itself, and the leading edge of the seal can be directed either toward or away from the blast forces; the brattice works equally well in either case. To hang the brattice, panels of brattice cloth about 0.9 m (3 ft) longer than the height of the airway are cut from a 1.8-m (6-ft) wide roll. The additional 0.9 m (3 ft) of brattice cloth allows 0.3 m (1 ft) for attachment to the roof by means of a board, with 0.6 m (2 ft) for forming a good air seal at the floor. Each brattice panel is wrapped once or twice around a 51 X 102 mm (2 X 4 in.) or 25 X 76 mm (1 X 3 in.) mounting board that is 254 to 305 mm (10 to 12 in.) shorter than the width of the panel. For convenience in

Jan 1, 1982

By Edmond O’Donovan

Mooranbah North is a new greenfield project in Australia's Bowen Basin that is projected to produce 4 mtpa of hard coking coal from a single longwall. Located in Central Queensland in Australia's northeast, this is one of Australia's main coal producing regions. From the outset, Mooranbah North's approach to equipment selection has differed markedly from that usually taken in the mining industry, and the conveyor industry in particular. Until recently, no performance requirements have been placed on conveyor equipment suppliers. This arose from a practice of purchasing components in an ad-hoc manner from a variety of sources, and the mine then configuring the system. More recently, single source supply has been adopted as a means of obtaining some performance guarantee, usually expressed in terms of system availability. Unfortunately, the term "availability" has a multitude of definitions, particularly in the underground coal sector. A conveyor availability of 98% is a common goal but this rarely means the conveyor must operate 165 hours/week, 52 weeks/year. There are mines that have one maintenance shift for each production shift and claim availability of 100%. What is meant is that no down time is logged to the conveyor during the hours that it is wanted. This "generous" definition of availability would not be tolerated in many industries and nor should it. Unfortunately, a true definition of availability, such as is applied to steam turbines in the power generation industry, is not particularly helpful. Five day/ week operations would immediately face a 28% penalty against 7 day rosters, and there would be no sensible manner in which weekend maintenance could be incorporated into the availability formula. The approach adopted by Mooranbah North was to specify a period of "Failure Free Operation," which would be followed by a maintenance period. This

Jan 1, 1998

By Hiroshi Himura, Shoichi Tsushima, Hiromi Goshima

This paper reports the construction of an environmentally-friendly tunnel in sedimentary soft rock near a residential area. The main tunnel, which will be used as the Onmawashi-Koen (Park) Regulating Reservoir, is a large-scale tunnel with a cross sectional area of 254.0 m2 and a lengthof 577.3 m, excavated using such support as shotcrete, rockbolts and steel H-sections. Since the large main tunnel is excavated in sedimentary soft rock, it is necessary to keep the stability of the tunnel face and the crown and to prevent surface settlement. A top heading with a length of 50 m is therefore driven as a pilot tunnel to observe the ground behavior during excavation, and to obtain information on the geological conditions based on which type of support structure is determined with consideration given to the results of field measurements and numerical analyses.

Jan 1, 2001

By Victor F. Hollister

Porphyry copper deposits can be categorized into three models for purposes of prospect evaluation: Breccia-pipe, modified Lowell and Guilbert, and diorite models. The modified Lowell and Guilbert model is normally associated with a quartz-bearing intrusive and a potassic, phyllic, argillic, and propylitic alteration sequence. Variations can occur in the alteration zones of this model that range from orthoclase-rich (Kalamazoo, Silver Bell, and Mineral Park) to ortho- clase-deficient (Petaquilla and Bougainville) potassic zones. The unifying features of the model are the presence of a phyllic zone and a quartz-bearing intrusion. The breccia-pipe model (Toquepala) is characterized by structure and alteration related to or controlled by breccia. Where tourmaline occurs in the breccia, the identity of the model is usually clear. However, if tourmaline is not commonly developed in the breccia (La Caridad), the deposit can be misidentified as to model. Porphyry copper deposits associated with quartz-deficient intrusives, whether these are calc-alkalic diorites or alkalic plutons, are characterized by alteration suites distinct from those of the modified Lowell and Guilbert model. These have been generalized as diorite model porphyry deposits. Because alteration and mineralogical development in diorite model deposits is distinct from that of the modified Lowell and Guilbert, ore guides and exploration tactics differ for the two models. The reprint that follows describing the three prospecting models summarizes their features. It is to be emphasized that these are models used in exploration for specific deposit types and are not genetic, tectonic, or geographic models. Porphyry copper deposits can be metamorphosed. Gibralter is an example of a Lowell and Guilbert model deposit that has undergone regional metamorphism.

Jan 1, 1991

By E. B. Kroeger

One of the problems encountered when constructing a roadway is the planned route often needs to cross soils that are soft and highly compressible. An approach to dealing with soft and compressible soils is to construct the fill from lightweight materials, thereby reducing the stresses on underlying soils. Most lightweight fills have approximately the same cost, so the most important consideration when choosing a lightweight fill is that the material properties of the lightweight fill match the conditions existing at the site. Expanded polystyrene (EPS) has been used as a lightweight fill material for more than 30 years. The EPS used for road fills is typically in the range of 0.5 to 2 lb/ft3, and has a compressive strength of in the range of 10 to 30 lb/in2. If a higher strength material is needed, then the material density is increased, which also adds to the cost of the material. Another type of lightweight fill material that is commonly being used is lightweight aggregate (LWA). LWA can be created by passing slate or shale through a rotary kiln or reheating coal fly ash with other materials to form pellets or aggregate. Several companies throughout the U.S market these materials under a variety of names. LWA can have a unit weight from 45-80 lb/ft3. For sites where trucking granular fill does not pose a problem, this material may be an alternative to EPS. One of the drawbacks to using LWA is the availability of the material. Only a few companies are manufacturing LWA, so it may not be available or may be cost prohibitive in certain areas of the country. Lightweight flyash blocks have been produced which may fill the gap in unit weight between the EPS and LWA. Blocks have been produced with a unit weight as low as 30 lb/ft3. They are relatively inexpensive, easy to handle, and have a moderate compressive strength. Although the unit weight is dramatically higher than EPS, the strength is also higher. If lateral stabilization of the fill is a problem, then geofabrics or grids can be incorporated into the design to add lateral strength.

Jan 1, 2003

By Paul D. Tomlingson

Maintenance costs in the mining industry often account for as much as 18-20% of total operating costs and with the cost of labor and materials rising, they threaten to become an even larger percentage of the total. Yet, without an effective maintenance program costs can soar beyond what they would be without a program. In other words, when production equipment is down, there is no production and no product to sell in the marketplace. This cost of downtime in lost product far exceeds the actual cost of maintenance, which is defined here as labor and materials. Thus, mine management must have an effective maintenance program to avoid downtime and meet production targets. Attaining an Effective Maintenance Program Many mine management and operations supervisors believe that an effective program is a function of how hard they push maintenance. Yet, when vital production equipment is inoperable and production is lagging, no amount of pushing helps. In actuality, maintenance has little control over its own destiny and needs support from other departments to deliver good service. Success of the maintenance program depends on gaining control of those factors that directly influence maintenance. Consider the following. Organization-The maintenance organization must be structured for maximum responsiveness to production needs. Unfortunately, some needs are immediate and many are unknown in advance. The maintenance department has little control over them. These outside influences limit the department manager's ability to control his own organizational structure. Preventive maintenance procedures-Routine lubrication, equipment inspection, minor adjustments and the like are controlled mostly by maintenance. Yet, scheduling preventive maintenance depends also on the availability of equipment controlled by other departments. Planning-The purpose of planning maintenance jobs is to ensure that the best use is made of maintenance resources. If the production department creates an environment of running repairs and emergencies, there can be little planning. Even well-planned jobs will suffer if there is less than full cooperation in carrying them out. As a consequence, the maintenance department is not blocked from planning, but the value of its planning is reduced. Scheduling-Maintenance scheduling should be a joint effort. Although maintenance does the planning, production must agree to the scheduled maintenance of its equipment. Workload-As a service organization, the maintenance department has limited control over its workload because it must consistently respond to other department's demands. At best, maintenance controls only the fixed portion of its workload-utility work, janitorial service, maintenance shop work, and assigned repetitive and preventive maintenance duties. Unscheduled and emergency work are initiated by operations. Major maintenance actions require full cooperation. Labor productivity-The effective use of labor is tied to other key functions of maintenance. These include organization, preventive maintenance, planning, scheduling, and emergency work. An area type organization, for example, can often respond more quickly to immediate needs than a centrally controlled maintenance group. Yet, area maintenance can result in lower labor productivity unless tight control is exercised. One of the advantages of a good "detection-oriented" preventive maintenance program is early discovery of problems and better opportunity to schedule corrective work in advance. Under planned work conditions, use of labor can be more productive. Complete planning and scheduling can minimize time spent on each job, increase effectiveness of supervision, and improve labor productivity. Finally, if emergency work is minimized, there are fewer delays, less lost time, better coordination, and more productive use of labor. While labor productivity is an important factor in carrying out maintenance, it also is influenced by outside factors. However, few realize the impact of being able to improve maintenance productivity. By improving the productivity of 30 men from 30% to 40%, maintenance could accomplish the same work value as if it had added 7.5 men working at 40% productivity. 30 (1800) (40%) = 21,600 man-hr/yr 30 (1800) (30%) = 16,200 man-hr/yr Difference = 5,400 man-hr/yr 1800 (40%) 7.5 men Leadership-The maintenance department can have significant control over its own leaders, the front-line foremen, but they must

Jan 12, 1982

By Robert L. Sundeen, Richard V. Wenberg

Overshot loaders are loading machines which fill a front-mounted bucket by crowding and bucket lifting, passing the loaded bucket over the machine and throw¬ing the load into a haulage unit to the rear. The load is retained in the bucket as the load mass is accelerated in its path over the machine. At the point of discharge, the bucket is stopped suddenly and the load leaves the bucket, following the throw trajectory past the rear of the loader. Fig. 1 shows a typical overshot loader of this type. Overshot loaders were developed for loading in nar¬row drift headings and drawpoints, where it is impossible to place or pass a haulage unit alongside the loader. Haulage access is to the rear of all overshot loaders. The first overshot loader was developed in the early 1930s. The early machines were rail-mounted, air¬powered, and had small loading capacities. To this day, the same basic design configuration exists, and all suc¬cessful overshot loaders still use compressed air. Bucket sizes range from 0.14 to 0.59 m3 (5 to 21 cu ft). The most commonly used machines are rail-mounted, al¬though crawler versions are popular for special applica¬tions, particularly shaft sinking. Rubber-tired machines have found some application where a greater travel distance is required between the loading and discharge points. CONDITIONS INFLUENCING APPLICATION Roadway Type Rail-mounted loaders are used where soft bottom requires rail support or where the long haul is ac¬complished with rail. This situation usually occurs in civil tunnels or in mine drifts that will continue to utilize rail-bound main haulage after development work is completed. Crawler and rubber-tire mounted loaders are used where the roadway surface is rough and lateral travel beyond the range of rail-bound machines is required. Work Area Dimensions The largest rail-bound loaders can clean roadways as wide as 4 m (13 ft) from a single track. Wider headings require multiple trackage. Headroom require¬ments are dependent upon the path described by the bucket as it passes over the machine. The largest over¬shot loader requires approximately 3.4 m (11 ft) of headroom. It follows that the largest heading that can be driven by overshot loaders from a single set of rails is approximately 4 m (13 ft) wide and a minimum of 3.5 m (11.5 ft) high above the rail. The smallest rail-bound loaders can work efficiently in headings as small as 1.8 m (6 ft) wide by 1.8 m (6 ft) high above the rail.

Jan 1, 1982

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Shrinkage stope mining can be employed in steeply dipping veins where both the wall and the vein material are sufficiently strong to stand with only minimal ground support. Shrinkage stope mining takes advantage of the swell in volume produced in breaking in-place ore. This expanded volume of ore is allowed to occupy part of the mined-out vein, and in so doing provides ground sup¬port and a working surface for the miners. Only enough of the ore is drawn after each stoping cut to allow work¬ing room. Not until the entire mining block has been broken is the full amount of broken ore drawn from the stope. DEVELOPMENT PRACTICES FOR SHRINKAGE STOPING The vein is developed into stoping blocks, each of which is 76 to 91 m (250 to 300 ft) in length and 61 m (200 ft) between levels. Level development, described later, is either on the vein or parallel to it with crosscuts periodically driven over to the vein. There are usually two exits from each stope. The first entry is a raise at one end driven either conventionally by raise climber, or by a raised borehole. Present practice is that this raise, put in from level to level, is either a 2.1- x 2.1-m (7- x 7-ft) Alimak raise or a 1.2- to 1.8-m (4- to 6-ft) diam borehole. Either raise system will require pro¬visions for an ore chute carried with the stope to the haulage level or the scram drift. At 9- to 12-m (30- to 40-ft) vertical intervals, dogholes are developed from the raise so that when stoping breaks back into these dogholes, timber or steel sets and necessary service facilities can be installed. The second entry to the stope may be either a similar raise at the stope endline, or more economically, a cribbed raise carried with the stope. As previously stated, development of the ore block is achieved by either drifting on the vein or by paralleling the vein with a footwall lateral and then crosscutting over to the vein at specified intervals. In the following discussion, three basic cases are illustrated in Figs. 1, 2, and 3. In Fig. 1, development is in the footwall by a 3- x 3-m (10- x 10-ft) trackless lateral. A heading is also driven on the ore and taken either full width or driven a standard size and slabbed to the vein width. Approxi¬mately 9-m (30-ft) long crosscuts on 7.6-m (25-ft) cen¬ters are driven from the lateral to the vein. For ease in muck handling they are usually put in on a slant rather than at right angles. A single orepass, located off the lateral and in the center of one stope block, can serve not only that stope, but also one on either side, up to a tramming distance of not more than 137 m (450 ft). Raises are put at the stope endlines on 91-m (300-ft) centers. The back of the vein is shot down and just enough broken material is drawn off to permit access for men to work off the broken ore. Development in Fig. 2 progresses by driving a 3- x 3-m (10- x 10-ft) trackless heading on the footwall side of the vein. The ore block is delineated by raises on 91-m (300-ft) centers. Crosscuts are again driven on 7.6-m (25-ft) centers over to the vein. Approximately four rounds are then taken up to the vein and each round is successively belled out so that all the crosscuts (pockets, in this case) connect. In this development, as opposed to that in Fig. 1 where there were no belled

Jan 1, 1982

By F. W. Brackebusch

Paste backfill is a pumpable, flowable, non-Newtonian fluid consisting generally of mine tailings and cement. Paste is prepared from dilute slurries of tailings. This is done by dewatering the slurries with conventional thickening or filtering. Backfill with a paste consistency is prepared by mixing dewatered tailings with cement and water to obtain the desired consistency of medium slump concrete. The paste is pumped with concrete pumps over relatively long (1 km or 0.6 mile) horizontal distances. More commonly, though, it flows by gravity down a mine shaft and then horizontally to the void being filled. Alternatively, cement can be added near the end of the pipeline. A certain proportion of fine particles <20 µm (<625 mesh) must be present in pastes but particles of aggregate can be added without significantly affecting the flow characteristics. Detailed testwork is necessary to design a system to prepare and place paste backfill. Testwork must determine dewatering characteristics, strength of mixes and friction in pipelines. Plants must be well engineered and controlled with PLCs because high quality control is necessary to prevent plugged pipelines and excessive pressures. Relatively small amounts of cement (3% to 5%) produce stiff backfill material 1.5 to 3.5 MPa (217 to 507 psi). The advantages of paste backfill in a mining operation include reduced mine dewatering, labor and materials savings, reduced tailings impoundment requirements, good support properties and reduced spills underground. In certain cases where more than 30% of the weight of the ore is sold as a product, the entire tailings stream can be placed underground. Paste technology can he used for surface or underground placement of tailings.

Jan 1, 1995

By Felicia F. Peng, Victor Z. Sun, Syd S. Peng

A probability-based analysis method in conjunction with the finite element structure modeling technique to evaluate an entry system stability is developed. Variability of the rock properties and loading surrounding the entry system is taken into consideration to predict a roof stability by using the probability of failure instead of the common safety factor concept. A dynamic programming is applied to establish a recurrence relationship between the degree of potential roof fall and accumulated roof fall index in an area of interested. A probable distribution of roof fall is assessed by using a developed computer program, RFSTAB. The assessment of the roof falling boundary in the longwall entry system is used as the example to illustrate the procedure and effectiveness of this analysis method

Jan 1, 1996

By R. F. Holub, E. Franco, T. B. Borak, K. J. Schiager

INTRODUCTION According to a recent analysis by Schiager et al.(1981), inhalation of radon daughters continues to contribute the largest risk from exposure to radioactive materials in underground uranium mines. The American National Standards Institute (1973) has published a concensus standard for radiation protection in uranium mines. According to this standard, a monitoring system for radon daughters must be capable of measuring the annual accumulated exposure in working level months within an uncertainty interval of 50% at the 95% confidence level. To satisfy this criterion, uranium mining companies in the USA have adopted a procedure consisting of single or periodic measurements of the air concentration of radon daughters. All of the measurement methods sample a known volume of air through a filter. After a specified delay interval, the filter is analyzed for radioactivity. The exposure rate from total airborne potential alpha energy in units of working level (WL) is estimated from the measured activity on the filter. For control purposes, this measurement establishes whether or not a work area is safe for occupancy by miners. For routine dosimetry, the concentration estimated from the grab sample is assigned to the appropriate work area. It is then assumed that the concentration of radon progeny is equal to the average of the two measurements at the beginning and end of the specified interval. Meanwhile, the work locations and exposure times of each miner are recorded on the daily time card and verified by the shift supervisor. Most cards provide space for 15-minute time intervals. The exposure in working-level hours (WL-hr) for each shift is obtained by summing the time spent in a given location multiplied by the exposure rate (WL) assigned to that location.The exposure of an individual miner to radon progeny is summarized on a weekly basis and commonly reviewed each month. These values are then accumulated in units of working level- months (WLM) during the calendar year. EVALUATION TECHNIQUE AND RESULTS The evaluation of grab sampling methods for monitoring exposure to radon progeny is presented in two sections. The first section examines each method individually according to accuracy, precision, and uncertainties attributed to human errors. The second section includes an analysis of procedures which are common to all measurement methods. The ultimate goal is to determine whether a specific measurement method, or grab sampling in general, can fulfill the criterion that the annual accumulated exposure of each miner be known to within ± 50% at the 95% confidence level. In addition it is essential that the above criterion be satisfied at an acceptable cost to the mining company. The results of each testing procedure are presented in terms of the contribution of the relative uncertainty in the estimates of cumulative WLM. Each of these are then combined to form a figure of merit for the complete monitoring system. The method of combining statistical uncertainties and interpretation of the results is subject to some debate. However, since all of the tested parameters enter into the final computation of WLM multiplicatively, we have used the commonly accepted procedure of combining the squares of the relative uncertainties. We have also assumed that each of the uncertainties is derived from independent random variables and the covariance of any two variables is zero. A description of each grab sampling measuring method is given in Table 1. Also included is the equation used to compute WL from the measured quantities. Accuracy (U A) Our definition of accuracy is based on the uncertainty inherent in any method which attempts to estimate potential alpha energy without unambiguously determining the concentration of the three unknown radioisotopes, RaA, RaB and RaC. (For simplicity, the RaC and RaC&apos; nuclides are referred to in combination as RaC.) The inherent uncertainty strongly depends on the mixture of these three components at the time of measurement.

Jan 1, 1981

By S. W. Kan, M. G. Kakarkis, J. Zelanco

Grouting has been used in underground mining for more than 20 years. Chemical grouting is often used as a remedial measure when the implemented ground-control program is unable to completely prevent structural failures or when there is a need for preventing a structural member from unraveling. The utilization of polyurethane grout is restricted by its limited range of physical and mechanical properties. To overcome some of the drawbacks of polyurethane, research is being conducted on a newly developed polyester based grout. The polyester resin, identified by Sandvik as Strata Grip, provides a number of features, including variable gel times and a much-reduced chemical hazard. Equally important are the mechanical properties of the product. The strength and deformability of any chemical grout must be compatible with the intended purpose of grouting and the expected deformation of the rock that is to be grouted The assessment of the mechanical properties of polyester grout is the focus of this work. Field experiences and laboratory research defined the properties of an effective grouting material. Experimental results indicate that the polyester grout meets or exceeds the recommended properties for many injection applications. Furthermore, the results suggest that the ability to adjust mechanical properties via resin formulation has the potential to expand the applicability of chemical grouting in ground control.

Jan 1, 1999

By V. G. Matziaris

The differentiation between saturated and un-saturated soils becomes necessary due to basic differences in their nature and engineering behavior. The most important difference is the existence of a suction zone, above the water table, in unsaturated soils. Pore water pressure in this zone is always negative and the shear strength is greater than the one in saturated soils. This is due to an occasional and apparent component in the Mohr-Coulomb equation, which appears in unsaturated soils. In slope stability analysis of unsaturated soils, the factor of safety increases due to this occasional cohesion component of the shear strength. However, the suction zone tends to disappear because of rainfall. In these cases the factor of safety decreases and eventually the slope may fail. In this article, a parametric study of the effect of suction zone fluctuation due to precipitation in slope stability is examined. For this purpose a Combined Hydrology and Stability Model (CHASM) has been applied.

Jan 1, 2005

By William J. Wasko

Maintenance of mining equipment has become so complex and important from a cost and product ion standpoint that the organization must be set up in an engineering fashion to be successful. Production costs are greatly affected by proper maintenance. Tonnages can only be met when operating time is at its maximum and breakdown time is at its minimum. Last, but equally important, large capital expenditures must be protected and improved The effectiveness of the maintenance program will, in many respects, be a direct, result of the effort put torch in developing the overall program. Once the need of maintenance is realized, the next step is to determine what the organization should be and what it should accomplish. Follow through is then most vital. Preventing machine breakdowns and reducing maintenance costs are the primary goals of all maintenance organizations. Good preventive maintenance, a system for inspecting equipment and a complete record of inspections will help attain these goals.

Jan 1, 1966