Search Documents

By Bruce D. McCellan

INTRODUCTION The gathering arm loader was patented by Joseph Joy in 1916. This unique machine motion became the standard of the industry and is used on underground loaders and continuous miners throughout the world. Figs. 1 and 2 show two types of gathering arm loaders. The gathering arm loader is a crawler-mounted ma¬chine primarily used for loading coal in a conventional mining system. Other uses also have been found for this machine in noncoal mines and other industries. MECHANICAL ASSEMBLIES The front or loading end of the machine, commonly called the head, consists of a tapered structural frame, hinged at the rear to the chassis and riding the ground at the front. Two bevel-gear cases are mounted in the head. They are connected by a timing shaft, which also acts as a conveyor drive shaft on most models. An eccentric disk attached to each gear case drives the gathering arms. The rear of the arms are attached to a swivel assembly. The motion derived from this arrange¬ment gathers loose material from the ground directly in front of the machine and loads it into the conveyor. Power for this drive is provided by two electric motors mounted under the gathering head. A speed reducer attached to each motor provides a gathering arm speed of approximately 5.2 rad/s (50 rpm). A torque limiting clutch is provided on each reducer to guard the system against sudden impact loading and continual overloading of the motors. The conveyor consists of an open box section through which a universal-type chain carries the ma¬terial to the rear of the machine, where it is discharged into the haulage vehicle. The chain is driven by a sprocket located on the timing shaft between the two gathering-head bevel-gear cases. On some large loader designs, primarily for noncoal applications, the chain is driven by a separate gear motor at the discharge end of the conveyor. However, the system driven by the timing shaft is used most widely. The conveyor frame is hinged just to the rear of the gathering head. It can be raised or lowered by hydraulic cylinders to the desired discharge height. The conveyor frame also is designed to pivot 0.79 rad (45°) either side of the center, just to the rear of the chassis. This feature increases the maneuverability of the ma¬chine and makes it possible to discharge material into the haulage system when in tight quarters such as when turning a crosscut. This function also is controlled by a hydraulic cylinder. The chassis of the loader consists of two crawler frames and cross members, holding the frames in position. The frames are either welded or cast as¬semblies. Replaceable wear runners are provided on the frames to take the wear generated by the crawler chain. An adjustable take-up idler keeps the crawler chain in proper adjustment for maximum life. The drive system for the crawler chains varies with the manufacturer, but it generally is one of two basic designs. One system provides a traction motor for each side of the machine, coupled to a speed reducer. A spur and bevel-gear train transfers power to the sprocket, which drives the crawler chain. Directional control is achieved by disk-type clutches. The other system also uses a motor for each crawler, coupled to a speed reducer. A roller chain drives the sprocket, which in

Jan 1, 1982

By T. H. Dubaniewicz, J. E. Chilton

The U. S. Bureau of Mines is investigating the application of fiber optic technology to methane and carbon monoxide monitoring. A methane monitoring system is described that is based on differential absorption of infrared light. It can detect concentrations as low as 0.2% and as far away as 2 km via fiber optic cable. The upper range is 100% methane. The system requires no electrical power within the mine so it should operate safely under mine disaster conditions. A hybrid carbon monoxide monitoring system is described that combines a low-powered electrochemical cell with fiber optic telemetry. Testing has shown the system can operate maintenance- free for several months.

Jan 1, 1992

By K. A. Natarajan

This paper deals with the various electro- and biochemical mechanisms involved in the bioleaching of multisulfide minerals such as those containing copper-lead-zinc and copper-nickel-iron. Galvanic series for sulfide minerals consisting of pyrite, chalcopyrite, galena, sphalerite, pentlundite, and pyrrhotite in an acid bacterial leaching system is illustrated, and the role of relative electrochemical activity on selective dissolution is discussed. Typical leaching results are shown to illustrate the practical applicability of galvanic effects in bioleaching of multisulfides. Attachment of Thiobacillus fewooxidans onto chalcopyrite and sphalerite mineral substrates is illustrated through scanning electron micrographs. The role of high-metal-tolerant, specially adapted strains in the leaching of multimetal concentrates is also outlined.

Jan 1, 1987

By R. J. Hamilton

Considerable success has been achieved in recent years in reducing concentrations of respirable dust in UK coalmines; thankfully this has been reflected in significant improvements in pneumoconiosis statistics. However, continuous increases in mechanisation and in rates of working, accompanied by more stringent dust regulations, necessitate the introduction of improved and often more sophisticated methods of dust control. The increased application of exhaust ventilation and air cleaning techniques seems likely to be the most important step forward in dust control in coalmining during the next few years. A typical drivage in a UK mine is not more than 16 ft (5 m) wide and is supported by steel arches. In the past the majority of such roadways were driven by the conventional means of blasting and loading. Since the main purpose of ventilation was to clear blasting fumes and to provide adequate scouring of firedamp, not surprisingly it was usual to have 'forcing' ventilation. Present systems of operation are making increasing use of heading machines and it is not surprising that well over half of all drivages are now ventilated by exhausting methods. (1) The great majority of coal getting in the UK is from longwall faces, usually in seams of less than 6 ft (1.8 m) thickness. Although this method of min¬ing has many advantages in terms of safety and productivity, dust control is made more difficult because of the need for men and machines to work in the same ventilation stream. Much emphasis has been placed on improving the design and methods of opera¬tion of longwall machines to reduce dust production, and improved ventilation has provided greater dilution, and in consequence, reductions in dust concentration. On all machines water is now fed through internal galleries to the cutting elements. Unfortunately, one of the difficulties associated with mining thin seams is that there is some unavoidable cutting in the roof or floor and in many seams there are faults to be traversed and dirt bands which must be removed with the coal. Under these conditions it appears that the use of exhaust ventilation and air cleaning offers the most promising way of achieving satisfactory dust conditions.

Jan 1, 1980

By Karl P. Norrena, Clayton V. Deutsch

Ore and waste cannot always be visually separated. The distinction between ore and waste may need to be made on the basis of blasthole sampling. Hand drawn dig limits or computer-generated contour lines do not account for uncertainty, economics or equipment. Geometric methods for interpreting grade information such as the polygonal or triangulation methods share the same limitations as contouring. Geostatistical techniques exist for the realistic modeling of grade variations and uncertainty. Decision analysis techniques exist for the binary classification of ore, and waste blocks in the presence of this uncertainty. Block-by-block classification is not enough; mining equipment cannot exercise free selection of blocks. There is a need for procedures to determine optimal dig limits that account for (1) the uncertainty in the grades, (2) the economics of risk-qualified decision-making, and (3) the ability of the mining equipment to dig to specific limits. This paper presents a procedure for optimal determination of dig limits that account for these constraints. Simulated annealing (SA) is used with modest computational requirements because the number of variables is relatively small. The solution of the optimization problem is dig limits that maximize profit under multiple constraints. The method is illustrated with different constraints and tested against hand drawn dig limits in a "Dig Limit Challenge," which illustrates the efficacy of the new method.

Jan 1, 2002

By E. Topuz, Xing Wu

INTRODUCTION The air flow in the mine ventilation network can be categorized in three ways: natural splitting, controlled splitting, and semi-controlled splitting. In natural splitting, the air flow in branches of a ventilation network apportions itself according to the aerodynamic resistance of the branches. In controlled splitting, a prescribed quantity of air is circulated through each branch. In semi-controlled splitting, flow in some branches is fixed to a desired quantity while in other branches it is split naturally. In practice, the mine ventilation networks present the latter two situations. Usually, the resistance of each branch in the network is known and the quantity of air in the working place is predetermined by safety considerations. If the number of branches whose airflow quantities are known is equal to or larger than the number of the fundamental meshes in the network, then the network becomes a controlled splitting network (Wang, 1982 a). Otherwise, it is a semi-controlled splitting network. If no booster fans are used in the network, the problem can be solved as either controlled or semi-controlled splitting networks in order to determine the main fan pressure and regulator size and location. All techniques are based on Kirchoff's flow and energy conservation laws and Atkinson's Equation. Booster fans can be used in controlled and semi-controlled splitting networks. It has been proven both theoretically and practically that using booster fans in these ventilation systems can improve flow distribution and reduce consumption of power (McPherson et al., 1985). The current techniques used in determination of booster fan location and size include simulation, linear programming, CPM and cutset operation, out-of-kilter, and critical-path crashing. These techniques can be classified into two groups. The first group, including linear programming, CPM and cutset operation, out-of-kilter, and critical-path crashing techniques, deals with controlled flow networks. The second, simulation, can be applied to the handling of semi-controlled flow networks. Mathematically, the problem of controlled splitting networks can be solved more easily than that of semi-controlled splitting networks. This is because the controlled flow network can be formulated as a linear programming problem, for the solution of which there are several sophisticated algorithms. Moreover, the semi-controlled flow network is usually modeled through nonlinear programming, for which there are no universally applicable solutions. The procedure described by Wu and Topuz, 1986, can be used to convert a semi-controlled network to a controlled flow network, and the problem can then be easily solved by the techniques used for solution of a controlled flow network problem. In practice, a mine ventilation network may change from controlled splitting to semicontrolled splitting with advancement of mining. This dynamic nature of mine ventilation makes the problem more complicated and necessitates development of new solution procedures which will consider the overall economics of the system. CONTROLLED SPLITTING NETWORK The problem in controlled splitting networks with booster fans is to determine the operational characteristic of the main fans, and the location and size of booster fans and regulators. The objective is to satisfy the air flow rate requirement for each branch while minimizing consumption of energy. The techniques used for the controlled splitting network problem include linear programming, CPM and cutset operation, out-of-kilter, and critical-path crashing. The objective function and constraints can be expressed as follows (Wang and Pana, 1971): [ ]

Jan 1, 1989

By John H. Duke

The success of most attempts to evaluate gold orebodies depends largely on the reliability and availability of representative sampling data and the accuracy of geological interpretation. An accurate prediction of the continuity of geology is paramount to a reliable prediction of gold reserves. Many of the problems encountered in gold mine evaluation and planning revolve around the difficulties in interpreting complex geology from sparse drilling data and the eagerness of mine financiers and promoters to start mining in order to derive an early cash flow. Following a program of sampling, geophysics, mapping and geological interpretation, a conceptual orebody model evolves in the minds of those working on the project. It is this model which is used typically in ore reserve computations and mine planning. Computer modelling techniques to represent and evaluate the conceptual model are now available. The main advantages of using computer modelling methods lie in being able to rapidly evaluate, modify and quantify the conceptual orebody model. Ore zones or domains can be recognised and defined both from geology and sampling results. Once these domains are defined as a series of boundaries, they may be modelled as two dimensional grid surfaces or as wire-framed three dimensional geometries, depending on the complexity of the orebody. It is the definition of these domains which provides the sound geological basis for reserves computation. To estimate reserves it is necessary to determine both volume of ore and grade of ore. The ore volume is calculated within each domain as defined by the confining surfaces or wire-frames. The ore

Jan 1, 1987

By P. M. Fozzard

The Chaucha porphyry copper/molybdenum deposit was discovered by a United Nations team of geologists working with a ?counter- part" team of staff of the Ecuadorian government's General Directorate of Geology and Mines (DDGM) in July 1968. The exploration program formed the latter part of phase I work plan of a two-phased exploration project financed by the United Nations Development Programme and initiated in late 1964. The author was a team geologist during the period 1965-1967 and subsequently project manager for the period 1968-1972. The Chaucha property lies some 10 km (6 miles) east of the north- south-running western boundary of what was known as Operation Area No. 5. This area of some 10 500 km2(4050 sq miles) is a square truncated to the southeast and centered on the city of Cuenca, the major provincial capital (Azuay Province) of southern Ecuador. The eastern half of the exploration area is dominated by the Cretaceous- Tertiary sedimentary valley (basin) of Cuenca (Caar-Azuay) and its related drainage area. The western half, in which Chaucha lies, is dominated by the high Cordillera Occidental volcanic plateau and the western erosional valleys of the Andes draining to the Pacific. The valley that dominates the eastern part of the area [I500 m (4920 ft) above sea level] is transected by the Pan-American Highway. Because of increased agricultural activity associated with the Cuenca Valley, the area is reasonably well covered by a road network of varying quality. The high western area up to 4000 m (13,120 ft) in altitude is largely barren and completely inaccessible by vehicle. The geological reconnaissance map of the region is shown in Fig. 1.

Jan 1, 1991

By Ruifeng Li, Yanghui Ren, Hua Gao

"Since entering the new century, China’s coal industry has witnessed the rapid development, and provided a reliable energy supply for the national economic and social development. But after the “golden decade” of rapid development, the coal industry now is facing overcapacity, low industrial concentration and production efficiency, high pressure of production safety and environmental protection and other prominent issues. Based on defining the connotation of highly-efficient recovery of coal resources, this paper established the relevant 8 indicators to reflect the highly-efficient recovery level of coal resources, summarized the present situation of China's coal resources recovery and the main problems, analyzed the development environment of China's coal industry under the new situation, and finally put forward the strategic measures to promote highly-efficient recovery of coal resources in China.1. Background Coal is the main energy in China. Since entering the new century, China's coal industry has made significant progress, and the level of production safety, resource recovery rate and mining mechanization increased significantly, which provided a reliable energy supply for the rapid development of the national economy. However, due to the changes of China's economic environment, slow growth of energy demand and other factors, some prominent contradictions in the coal industry have significantly restricted the healthy development of the industry. The first problem is serious overcapacity. In the past few years, 16 industries including coal, electric power, chemical and others have invested in coal mines. It is reported (Han 2016) that only during the nine years from 2005 to 2014, the fixed assets of coal industry increased totally more than 3.3 trillion RMB, which brought a large number of production capacity. Affected by the slowdown of economic growth and energy structure adjustment, Chinese coal demand has reached the peak platform and caused the overcapacity of coal supply, so shutting down the backward capacity is the most important task in the future. The second problem is the low efficiency of coal production. There are about 4.3 million coal mine workers in China, and the annual coal production per capita is less than 900 tons, while it was reported (EIA 2016) that the annual production per capita in the United States is more than 10 thousand tons. The third problem is that the green coal resources are not rich. Among the 1.53 trillion tons proven reserves, only about one third are green coal resources in accordance with the principle of ""safety, technology, environment and economy"". The coal resources with high quality and easily mining conditions are not abundant."

Jan 1, 2017

By W. J. Nelson

Detailed underground geologic map- ping at a scale of 1:1200 has been carried out at the Crown II Mine of Freeman United Coal Mining Company, which operates in the Herrin (No. 6) Coal Member. The roof sequence, upward from the coal, includes (1) soft, medium- to dark-gray shale; (2) hard, black, fissile shale; (3) argillaceous nodular-bedded limestone, and (4) fine-grained, shaly, water-bearing sandstone. The first unit is highly lenticular, and any or all may be missing at a given locality. The sand- stone has a sheet facies and a channel facies. The Herrin Coal is eroded in channels near the Crown II Mine. Structural features mapped at Crown II include normal and strike-slip faults of small displacement, "slips" and clay dikes, and limestone "bosses." Less stable roof and wet con- ditions are encountered where the limestone is thin or missing or where it is broken by natural fractures or by artificial openings that inter- sect the water-bearing strata above the limestone. Geologic mapping of the underground workings has allowed us to predict faults, fracture zones, and channels ahead of the face for this mine. Some lithologic and structural patterns apparently are random and cannot now be projected. Conventional exploratory drilling is entirely inadequate to map faults or lithology of the roof, but it does indicate the range of lithologic variability, which can be used to project needs for roof sup- ports. Drilling also is useful In locating channels and in mapping regional variation in thickness and facies of the sandstone.

Jan 1, 1980

By Stuart R. Cotterill, Jack D. Nelmark

Introduction Opencast surface mining requires blasthole drilling to achieve mine planning. No single method of mining is right for all conditions. Occasionally, mine planners introduce a project with little regard to drilling and blasting. These costs are usually a significant percentage of total mine overhead. One drilling and blasting method that can be used to reduce overall mine expense is inclined or angle hole drilling. But inclined-hole drilling will not cut costs unless a set of required circumstances is met. Several conditions of mine design indicate the use of angle drilling. Geotechnical problems must first be analyzed. Primary considerations are safety, fragmentation, production, and maintenance. Secondary considerations are, in some instances, reduction in amount of explosives, which lowers blasting costs; reduction of practical fragmentation beyond blasting pattern limits; and reductions in overall costs due to reduced volume of excavation. Future trends in blasthole drilling may include incorporation of drill equipment designed to allow rapid change from vertical to inclined drilling. This will allow the operator to adapt to changing hole requirements with minimal production loss. Another improvement may be the ability to chamber holes at any elevation throughout the hole depth. This will allow more charge to be placed at strategic locations to improve fragmentation. Merits of Drilling Inclined Holes Drilling is performed to create voids for explosives. It is done either to recover minerals or to excavate a volume of earth. The manner of mining or excavation can greatly affect the economics of the overall project. Many innovations and methods have been tried, but the most practical and economical is still drilling holes and using explosives to fragment the material. To break up the material, the practice has been to place charges within the mass. This is done by drilling holes of a specific diameter and depth into the material. The holes are of such magnitude as to develop sufficient energy to break or loosen this material, providing for easier removal. In general, more open or exposed faces must exist to aid material breakage when blasting. Inclined drilling can be advantageous in open-cut mining with highwall depths of at least 24 m (80 ft). A minimum of two faces are open in open-cut mining and the material can be thrown outward to cover pre-mined volume. This cuts cost by eliminating the need to remove or relocate a large portion of material. Sometimes the material is of such a mass that more energy per unit is required to loosen it than can easily be done by blasting vertically. Inclined holes allow a more uniform loading of drilled holes. The unit of energy is raised, so little or no secondary blasting is required. This usually comes about only if the main plan calls for drilling holes deeper than 24 m (80 ft). For shallow holes, spacing and burden can be made closer to allow sufficient energy to blast the toe. If the open face is in only one

Jan 9, 1984

By Geoff C. Knight

Longwall mining using the shearer is acknowledged internationally as the most economically successful method of high volume production from underground coal mines. Since its introduction in the 1950s, a great deal has been achieved in developing the capability and reliability of the shearer - and the associated face conveyors and powered roof supports - to produce the competent systems now widely deployed. Equipment will continue to improve as knowledge and experience are gained and through the influence of market forces on the international equipment suppliers. However, current systems are so successful that further improvements are likely to be incremental rather than radical unless a high level of system automation is introduced. The automation concept is not new to the shearer-based longwall system. The opportunity and the need were recognized soon after the shearer and powered support were introduced in the 1950s. In the early 1960s, the British Coal Corp. (BCC; then the National Coal Board) attempted remotely operate longwall systems. Those imaginative early schemes were seen as failures at the time. But, with hindsight, a great deal was learned from the experience that stimulated automation research in several European countries. One of the most fundamental lessons learned was that coalface system automation is not possible until there is a high level of competence in automatically controlling the operation of the production machine itself within the coal seam. Once that is achieved, the rest of the system will follow with comparative ease.

Jan 1, 1991

By Ronald E. Heuer

The significance of surface settlement over soft ground tunnels is well recognized. Cracked buildings, streets transformed into lakes, broken utility lines, to underpin or not to underpin--all are familiar problems. The basic causes of surface settlement are recognized. Possibly the most common and troublesome cause is "lost ground" during construction. Lost ground refers to removal of a larger volume of ground (Ve) than is eventually occupied by the final tunnel structure (Vt). A number of sources of lost ground in shield tunneling have been identified, as illustrated in Fig. 1. These include 1) face loss, 2) overcutting loss, 3) annular tail void loss, and 4) loss through the lining. The ground generally does not stand unsupported around the completed tunnel lining as illustrated in Fig. 1, but moves in to fill the lost volume, resulting in subsidence of the overlying ground surface as shown. As suggested in Fig. 1, lost ground and surface settlement associated with overcutting and the annular tail void tend to occur systematically along the tunnel length. This "systematic" lost volume is "limited" in the sense that it is restricted to an upper limit determined by the shield and lining geometry. Partially controlled face loss may sometimes contribute to this systematic loss. This lost volume is commonly a few percent of the nominal tunnel volume. The resulting surface settlement over the tunnel is commonly in the range of a few inches or less and develops over a period of hours to days. Although they may have a significant impact on surface facilities, systematic ground loss and settlement frequently have little adverse effect on tunneling progress.

Jan 1, 1976

By W. G. Pariseau, S. C. Schmelter

The destabilizing effect of water pressure on rock-mass stability is examined quantitatively by the finite element method. A coupled code that accounts for the simultaneous effects of rock-mass deformation and transient fluid flow is used for this purpose. The traditional soil-mechanics assumption of an incompressible fluid is shown to be untenable for the analysis of porous, fractured rock slopes. A Mandel-Cryer effect, whish is a transitory but elevated and potentially destabilizing water pressure following a cut, was not observed.

Jan 1, 1999

By Ivor Hawkes, Malcolm Mellor

INTRODUCTION There are currently around fifteen companies in the United States and Europe manufacturing hard rock tunneling machines. In recent years upwards of 200 hard rock tunnels of lengths up to 12 miles and diameters to the order of 30 ft have and are being successfully driven by over 100 different machines. It has been predicted that within the next decade over 2,000 miles of tunnels will be driven for transportation purposes in the United States alone (OECD Advisory Conference on Tunneling, Washington, 1970) and it is expected that eventually most tunnels including mine drivages will be excavated by machines. All tunneling machines have certain common basic functions; thrust is applied to drive or hold the rock cutting tools into the face, and torque is applied to rotate the cutting tools over the face so that they can continuously break out rock. The speed of head rotation, together with the torque requirement, determines the cutter head power. (The power required to push the head forward is usually negligible.) There are many factors which determine how successfully a given tunneling machine will perform in a given rock but one of the most important is effective utilization of cutter head power. This paper is a review of the specifications and performance of hard rock tunneling machines, obtained from manufacturers' catalogs, published literature, talks with manufacturers and visits to operating machines throughout the United States and Europe.

Jan 1, 1997

By Jerry Solomon

The subjects to be examined in my portion of the session entitled "Technology of Aluminum.. Recovery" will be twofold. 1. Economics of the basic aluminum economy--supply-demand-price. 2. Specifications of aluminum products produced from municipal waste--from the secondary aluminum standpoint. It is the object of this speech to first impress everyone with the excellent long-run markets for the aluminum products from municipal waste and then to acquaint everyone with the rather liberal scrap specifications that the recycling industry can tolerate. The most important statement that can be made about the recycling of aluminum is that it is now and will be an economic necessity. This is true far many reasons; one which hit the headlines recently was Interior Secretary Rogers Morton's statement "Third-world nations could use mineral wealth not to achieve political ends but to jack up economic positions. The result could be sky-rocketing prices and dwindling supplies on world markets." There is no reason why the group of countries that supplies most of our bauxite can't get together the way oil-producing countries got together on the price of oil. (Jamaica and Surinam, are original sources of two-thirds of the aluminum used in the United States.) The worry is not so much that we will end up without the basic raw material but rather that the price might be so high that we could not afford it. So much for the blackmail reason for recycling aluminum; the supply and demand picture in both the primary and recycling sectors of the aluminum economy is far more meaningful.

Jan 1, 1974

By Hasan Sevim

A computerized heuristic model for an efficient and economic design of belt haulage networks in underground coal mines is discussed. The model is versatile, easy to use, and is valid for all mining methods singly or in combination. It may be used to design new networks or to analyze existing networks. The input data required are 1. maximum production rates from a section, 2. probabilities of production rates, 3. equipment costs, and 4. data necessary for network coding to represent different cases. The objective function is the "expected minimum cost per ton of coal hauled" while meeting production requirements. The output includes belt width, motor horsepower, bin size etc. and also values of operating parameters for each belt such as belt speed, effective tension, power consumption etc. A detailed account of the cost involved is also provided for each unit as well as for the entire network. Description of the model and an example of the design of a belt network in a mine with two longwall and four development sections are presented.

Jan 1, 1986

By Charles C. L. Smith

A review and comparison is made of the circuitry utilized for dc crane control systems. Anti-parallel three phase full wave thyristor bridges for dc motor reversing and speed control are compared with a single three phase full wave thyristor bridge for speed control and either contactor or static switching for reversing control to obtain complete four quadrant operation for crane material handling. In recent years the Harnischfeger Corporation has developed a solid state adjustable voltage control system to control the speed and direction of dc motors for crane applications and handling materia1.1 Shunt wound dc motors are utilized and speed is controlled in the motor base speed operating region at constant torque by a thyristor, silicon controlled rectifier (SCR), adjust- able armature voltage supply. The three phase thyristor bridge is the power controlling element of the dc adjustable voltage control. ELECTROTORQUE is the Harnischfeger Corporation registered trade name for this type of drive system. By controlling the gating signals or firing pulses to the thyristor bridge SCR's the dc output voltage can be varied over a wide range. This range is limited only by the magnitude of the ac applied voltage. To obtain operation of the motor in both directions two thristor bridges are connected in an anti-parallel arrangement. A typical schematic for two anti-parallel connected three phase SCR bridges is shown in Figure 1.

Jan 1, 1973

By Jeffrey M. Listak, Gregory J. Chekan

The U.S. Bureau of Mines, in an effort to improve coal conservation and utilization is currently investigating longwall panel layouts to maximize coal recovery and minimize interactive problems in multiple-seam operations. When longwalling coalbeds in descending order, the transfer of stress from overlying gate roads is a major design constraint affecting pillar stability in the lower mine. The lower mine gate road pillars must be properly designed to withstand the additional load transfer if gate roads are superpositioned in successive seams. The Bureau's MULSIM/NL model was used to analyze load transfer mechanics for superpositioned gate road pillars. Analysis of Longwall Pillar Stability (ALPS), which is an empirically based design method for longwall gate road pillars, was used to calibrate model input parameters. The attributes of both the MULSIM/NL model and ALPS were combined to develop a modified method for estimating pillar stress for multiple-seam cases. The modified method uses a multiple-seam (MS) factor to estimate the stress on the lower mine gate road pillars when superpositioning is practiced. Numerical analysis shows that the MS factor is dependent upon the interburden thickness and pillar width and is presented in a series of graphs relating these two parameters. Several examples are included to illustrate the use of the MS factor for estimating lower mine pillar stress and resulting stability factors.

Jan 1, 1992

By Y. A. Attia, D. K. Sengupta, H. A. Hamza

Increased recycling of waste paper has been emphasized in recent years in both the United States and Canada for environmental and economic reasons. Removal of ink particles from waste paper pulp is therefore necessary. One of the most promising methods for ink removal is froth flotation. This study investigated the feasibility of a simplified flotation scheme and found that about 90% to 92% ink removal can be achieved. Also, a 95% to 97% ink removal is achievable if a hydrophobic polymer is used ahead of the flotation stage. Clean paper pulp recovery was over 90%. The effects of pulping pH, flotation pH and concentrations of flotation and polymeric reagents are discussed in the paper.

Jan 1, 1995