Search Documents

By W. J. Pennstrom, J. R. Arnold

This paper focuses on solution-balance management around heap-leach operations. Experience has shown that increased leach recoveries can be achieved by utilizing various leach-solution recirculation techniques. The most prominent solution-recirculation technique is intermediate leaching. The net effect of intermediate leaching is to increase recovery plant performance by increasing solution concentration tenors, to increase metal recovery by increasing the total leach time and to decrease the overall capital expenditures required for metal-recovery facilities. The adverse effect on the flow of cash from increased metal inventories in the recirculating solutions is offset by increased metal recovery and lower operating costs per unit produced.

Jan 1, 2000

By Tim Neil, O&apos

Finnish mining traditions date back 400 years. The country was then one of Europe's major iron producers. Most of the mines in current operation, however, were started during the last 20 to 30 years. The Finnish mining industry must make do with limited resources. Deposits are usually low grade and small in size. Open-pit methods are used where possible. But thin ore bodies and harsh winters can impose severe restrictions. Underground mining is often the only option. Despite these handicaps, Finnish metal miners produce copper, nickel, zinc, vanadium, iron ore, cobalt, and ferrochrome. Ironically, the success of Finnish mining is rooted in a crisis the industry faced several decades ago. Mining costs were rising. High grade mineral deposits were nearly exhausted. It was vital that Finland develop new mining machinery and methods that afforded higher productivity. Cooperation between the Finnish mining industry and its equipment manufacturers was good. Partly as a result, the Finnish mining industry has turned itself into one of the most modern and efficient in the world. The Finns did this while continuing to meet the stringent safety and environmental requirements in force in the Nordic countries. Today, the share of domestic raw materials used by the Finnish metallurgical industry is decreasing. So the country increasingly depends on imports of ores and concentrates. To better provide these imports, Finnish mining companies have expanded their foreign operations. And, while importing raw materials, the mining industry has been exporting its technological and equipment know-how and expertise. Mining methods Conventional mining methods and machinery are used in surface mines. Drilling is the exception. It is done with Tamrock hydraulic track drills and 100 to 150 mm-diam (4 to 6-in.-diam) drill holes. Pumpable slurry explosives are used in larger open pits. Underground, sublevel stoping with open stopes is the most common mining method. It accounts for about 80% of all underground stoping. The main benefits of this method are low production costs, high mechanization, and easy control. The best productivity figures exceed 10 t (11 st) per man-hour, including all mining personnel. The development of cable bolting has made it possible to use sublevel open stoping even in relatively weak rock. Cut-and-fill methods, such as concrete-pillar stoping, inclined-wall stoping, and traditional cut-and-fill have also been used, combined with sublevel caving and room-and-pillar methods, according to local demands. Various fill materials and stabilization components have been investigated and tested for cut-and-fill methods. Sublevel open stopes are often later filled, to stabilize the surface or to allow pillar recovery.

Jan 10, 1988

By M. W. Harmer, J. M. Quist

Laboratory test work, pilot plant testing and plant experience with wet, fine-mesh screens are discussed. High-frequency, low-amplitude, fine-mesh, wet screens were installed on the 6th cleaner concentrate stream. These screens produce a 60% oversize recovery split of the molybdenite concentrate that is of leached equivalent quality. The undersize stream is leached with hot ferric chloride to remove lead and copper contaminants before roasting or shipment to sulfide customers. This plant modification is a good example of using existing technology in an unconventional flow sheet to yield significant cost savings.

Jan 1, 1991

By Q. Lin, D. Z. Wang

Molecular design plays an important role in development of new flotation reagents. Group electronegativity calculation is a main method of molecular design. It is commonly used in calculating the hydrophilic-hydrophobic balance of reagents, particularly in designing chain length of flotation reagents for located minerals. But there is a limit to group electronegativity method. The method can only apply to those of [Ø]known straight-chain compounds ([Ø] is the hydrophobic energy of each -CH2- , determined by experiment). In this Paper, we propose another new calculation method: fragment method of flotation reagent. The method could be used as a supplement of group electronegativity method to design and calculate flotation reagents without any limitation. With the fragment method, we can calculate the hydrophilic-hydrophobic performance of any known or unknown reagents including those complicate structure compounds such as cyclic, branch, heterocyclic and so on by summing the appropriate structural elements (fragment). The principle, calculation stages and some results of designing new-type flotation reagents by fragment method are presented in this paper.

Jan 1, 1995

By Warren W. Frech

11.1-FRAGMENTATION PRINCIPLES WARREN W. KRECH Energy must be supplied to rock by direct or indirect means to fragment that rock. The amount is dependent upon the properties of the rock and the type of loading system. Fragmentation energy is consumed by three main mechanisms: (1) creation of new surface area (fracture energy), (2) friction (plasticity) and (3) elastic wave energy dispersion. The loading method determines the relative proportions and the amount of energy consumed in fragmenting a given rock type. Unconfined tensile failure consumes the least energy, with an increasing amount of energy required as the rock is more highly confined within a compressive stress field during fragmentation. The way energy is applied by tools to cause rock or mineral fragmentation is important in determining fragmentation efficiency. Rock-tool interaction should always be controlled to the fullest extent possible to optimize the combination of rate of energy input and fragmentation energy requirements. While the direct cost of energy, (dollars per horsepower-hour) may at first glance appear low relative to other hourly costs, there is a tie between power consumption and other cost factors, such as maintenance and wear. A high rate of energy application utilizing a rock-tool interaction producing only unconfined tensile failure would provide the most efficient fragmentation. No tool that produces a combination of high energy input rate and a loading system that produces failure under only conditions of unconfined tensile load now exists. Present mining methods and tools produce failure under conditions of high compressive confinement, high dispersive energy loss and high frictional energy requirements. Thus, while generally applying energy at high rates, they are highly inefficient with respect to energy consumed in fragmenting rock. To best design fragmentation tools and optimize fragmentation systems it would be desirable to know how rock properties influence breakage. At present, rock properties directly- related to fragmentation are undefined. Although present testing technology- does not permit rigorous definition of in-situ rock fragmentation behavior, several properties (mechanical and physical) commonly are used to indicate the relative case with which rock breaks. The more common test is for uniaxial compressive or tensile strength of cylindrical cores taken from intact portions of the in-situ rock (testing details are provided ill Sec. 6.2, Rock Mechanics). The strength of rock is influenced by the environmental conditions imposed on the rock. Those of most importance in rock are (1) confining pressure. (2) pore fluid pressure, (3) temperature and (4) rate of load application. Increase in confining pressure, as with increasing depth beneath the earth's surface or under the action of a fragmentation tool, causes an increase in rock strength. Increases from atmospheric pressure to 10.000 psi commonly cause up to n fourfold increase in the compressive strength of crystalline rock. Apparent rock strength decreases as pore fluid pressure increases, since it decreases the effect of confining pressure. The effective stress concept of soil mechanics generally applies to rock. Although chemical effects of pore fluids influence rock strength, they geologically are small compared to the confining pressure effect, except for a small minority of rock types. Increase in rock temperature causes a decrease in rock strength. This effect

Jan 1, 1973

By Christoph Wels, Michael Royle, Shannon Shaw

Intrinsic remediation is the effect of natural attenuation mechanisms - dilution, dispersion, sorption/precipitation and biodegradation - reducing contaminant concentrations in ground water to specified levels at predetermined compliance points in the aquifer. Current monitoring and modeling for post closure was used to assess the current and long-term potential of intrinsic remediation of contaminated seepage originating from a large reactive (sulfidic) tailings impoundment near Questa, New Mexico. It is concluded that the natural attenuation mechanisms of precipitation within the tailings (as a result of buffering) and dilution/dispersion within the aquifer are currently active and likely sufficient to reduce contaminant concentrations to below state standards in the long-term. Other natural attenuation mechanisms such as sorption and biodegradation within the receiving aquife4s) were not assessed here, but are likely further reducing contaminant concentrations. Active interception and recovery of the seepage water is being maintained until monitoring demonstrates that intrinsic remediation has successfully achieved the level of water quality control required.

Jan 1, 2000

By G. P. Hand

Graphite usage in the United States during 1994 was fairly strong. The hearty showing of the domestic economy, along with sound performances from the major industries that use graphite, helped make 1994 a solid year for the graphite industry. Supply Virtually all natural graphite is imported into the United States, as there is no domestic production. The primary producers are Brazil, Canada, China, Madagascar, Mexico, Mozambique, Sri Lanka and Zimbabwe. Mozambique is a new producer. It is now supplying a high-carbon, large-crystallite flake in large quantities. Sri Lanka continues to experience problems with one of its two mines, closing operations in December 1994. The synthetic graphite used domestically was produced primarily in the United States as a byproduct of electrode production. Synthetic graphite was also imported from Switzerland for specialized applications. The purified graphites/carbons, such as Desulco and ThermoPURE materials, were also produced domestically. There was a sufficient supply of all types of graphite to meet domestic demand.

Jan 1, 1995

By R. A. Pond

Two 6.17 m (20 ft 3 in.) diameter raises, concrete-lined to 5.49 m (18 ft) inside diameter, were completed in 1978 at the Monterey Coal Company Number One Mine near Carlinville, Illinois, by Frontier-Kemper Constructors. These two raises are the largest in cross-section yet completed by full-face upreaming, and the success of this project is expected to increase the application of raise-boring to coal mine shaft construction. WHY 6.17 M (20 FT) DIAMETER ? Raise boring is well accepted in the metal mining industry for a variety of applications, and is gaining in acceptance in the civil works construction industry. The use of raise boring to construct vertical openings for coal mines has not been as widely accepted, even though coal mining requires, per mine, the greatest number of openings to the surface of any underground activity. Several factors have influenced the low utilization of raise boring in coal mining: 1. Coal mine shafts must often be of large diameter to pass the required high volumes of ventilation air at acceptably low water gage pressures. Cross-sectional areas of finished shafts exceeding 23.23 sq m (250 sq ft) are common. 2. The life of ventilation shafts is comparatively long, and the typical sedimentary strata overlying coal seams normally require that the shafts be lined. Shafts on the intake ventilation circuit must have permanent water-tight linings. 3. Unconsolidated overburden at the surface is often thick, and as reaming cannot be safely utilized in unconsolidated material,

Jan 1, 1979

By Jack G. Pippenger

The Coteau Properties Co.'s Freedom Mine is a surface lignite mine that uses large draglines, trucks and shovels, tractor-scrapers and bulldozers to uncover a single coal seam. In 1989, a work order system was instituted to record data by equipment type, cost, productivity and distance. The system was also used to provide historical information to plan the most efficient and economic use of each equipment type in the mining operation. The Coteau Properties Co. is a wholly owned subsidiary of The North American Coal Corp. The company was formed in 1972 to supply lignite from its Beulah-Hazen coal reserve to a coal gasification project and an electrical generating facility located near Beulah, ND. The reserve consists of a single coal seam between 3 and 7 m (10 to 23 ft) thick. The overburden above the coal is predominately glacial tills and clays and ranges from 6 m (20 ft) to more than 60 m (200 ft) thick.

Jan 1, 1994

By S. L. Bessinger

The need for improved safety and productivity brought about the introduction of longwall mining to the Appalachian coal fields. These same forces continue to drive developments in modern longwall equipment and mining practices. Current initiatives to improve productivity and safety are focused on automation and the effects of scale in equipment design. Longwall roof-supports, shearers and face-conveyors have changed significantly. Panel layouts have evolved to include larger total tonnages and provide for more rapid development of gate-entries. These advancements have improved longwall productivity and new production records are continually being set. Roof supports Reliability is implicit in the quest for automation. It is impossible to automate equipment if it is not reliable. To a large degree, this has been the problem with longwall shield automation efforts. The "electronic control" of shields depends on the proper functioning of electronic equipment, electrohydraulic valves and full-flow service valves onboard every support.

Jan 1, 1995

By P. Tsang, S. S. Peng

Mine floor failures, such as floor heave and floor buckling, occur frequently in underground coal mines where soft mine floor exists. The types of failure can usually be classified into two categories; shear punching failure and tensile failure. A model based on the Winkler's elastic foundation is proposed in this paper for floor stability analysis. The model considers material properties of floor strata, in-situ horizontal stress, pillar size, entry width, and configuration of multiple-entry system and predicts stress conditions in the mine floor based on given in-situ mining and geological conditions, as well as deformation of the mine floor. This information is used to predict possible failures of mine floor by comparing the strength of mine floor with its stress condition. The validity of the model is verified by in-situ data described in this paper.

Jan 1, 1992

By Pooyan Asadollahi, Praveen Krishna, Michael Joye

"Durability design for underground structures is an increasing focus of designers and owners in the underground construction industry. Many owners have expanded their requirements for durability design, with specific requirements for structure lifecycle and designer certification of structural durability. This paper describes current trends and best practices including: defining the underground structure lifecycle, historically durable underground structures, design methods for underground structure durability built of reinforced concrete, and durability of materials. Criteria to be used for defining end of structure life and owner’s maintenance responsibilities are crucial to lifecycle contract requirements. Current practices of several major owners are presented. Design methods are presented including United States code requirements. Current best practices for enhancing the durability of materials used in underground construction are discussed including: low permeability concrete, steel reinforcement concrete cover, the use of steel fiber, and testing for verification. INTRODUCTION Durability design is increasingly being recognized as an essential component of good design practice. Infrastructure owners recognize that to serve the public interest, constructed facilities must be lasting and durable. The public understands that structures with limited service life result in increased costs and add to their daily inconvenience with frequent repair and reconstruction. Engineers are increasingly asking not only is the structure strong enough but will it last for generations. Durability design requirements are no longer just adherence to some accepted practices, but are based on analytical approaches, with results that can challenge our beliefs in what construction materials and details result in a durable structure. This paper describes current industry requirements and practices for durability design of underground structures, and offers some suggestions regarding future trends and developments. SERVICE LIFE DEFINITION The service life of a structure is the sum of the time to onset of deterioration, called initiation period (ti), and the subsequent time period of deterioration ending when the structure is no longer functional, called propagation period (tp). Figure 1 shows a conceptual service life diagram. These time periods can be substantially affected by the level of maintenance performed during the life of the structure."

Jan 1, 2016

By J. B. Yianatos, G. S. Dobby, J. A. Finch, A. R. Laplante, R. Espinosa-Gomez

The question is posed as to why columns typically have a collection zone 10 m high (H) by 1 m in diameter (D). Three geometry dependent factors are considered: degree of mixing, Np; volumetric bias rate, B; and volumetric gas rate, G. Increasing H:D decreased Np and B, which improves performance but decreases G, which causes the column to approach overloading. Taking typical column operating conditions, it is concluded that a collection zone H:D of 10:l is a reasonable compromise.

Jan 1, 1987

By Roger S. Dewey

1.1. INTRODUCTION Despite indications of a general economic recovery in the U.S. during the mid-19801s, mine operators have not generally shared in the benefits of these reported better times. Budgets have not rebounded, borrowing is tougher, parent companies' pockets are not as deep as in previous years, and margins are not any better -- if there is any left over at all. Managing capital equipment budgets is always a challenge, and the last five years of stretched equipment lives make these decisions more tenuous. Delays and avoidance of replacements due to tough times inevitably makes those decisions increasingly difficult and usually more expensive The purposes of this paper are to present. a brief refresher outline of the fundamentals of equipment replacement analysis, to suggest a number of papers where analysis methods are explained in greater detail. and to recommend the use of a widespread microcomputer software capability (1-2-3) as the easiest path to a much-needed solution for a very difficult, and usually under-supported management decision problem 2. REPLACEMENT DECISION POLICY Investments in equipment replacements must compete for capital with all other investment alternatives. Capital for replacements of ten represents a greater commitment than do the new projects which a company might handle in a given year. But. sadly, formal policies for standardized analysis of replacements rarely exist, even in major companies. Yet this policy can be very significant in determining the competitiveness of a firm. Whereas many replacement decisions are based on cost minimization, economists and financial analysts agree that wealth maximization or return on investment is the superior criterion. Though the difference may seem slight, agreement on a firm's financial objective is vital. Replacement policy should be straight- forward. have a logical basis, and a proper level of sophistication. There are several reasons to develop a policy for replacement decision-making: [I] 1 - equipment's optimal economic life is nearly always shorter than its physical life; 2 - mine life often exceeds equipment life, so management must face these decisions routinly 3 - replacement capital costs, on an undiscounted basis, can run 25 to 75% of original capital 4 - technological changes may result in a newer machine or system which can operate more efficiently, more safely. or less expensively 5 - estimates should be made consistently in the fundamental areas of life expectancy, availability, utilization. price escalation, taxes 6 - long-term and short-term budgeting without decent data and analytical capability is nearly impossible, or at least ineffective Policy development assumptions which must be considered include: the planning horizon, cost patterns, interest rates, availability of capital, replacement vs. expansion, technology advances.

Jan 1, 1987

By Graeme J. Jameson

A form of column flotation cell is described in which the contact between the feed and the air stream is made in a mixing device at the top of a vertical downcomer. The air-liquid mixture flows downward to discharge into a shallow pool of pulp in the bottom of a short cylindrical column. The bubbles disengage and rise to the top of the column to overflow into a concentrate launder, while the tails are discharged from the bottom of the vessel. The main advantages of the device described are that the overall height of the column is reduced to about one metre (3 ft), and the column can be self-inducing with respect to the air supply. Experimental results are given from tests on a feed stream to a conventional zinc cleaner circuit. Using wash-water to reduce gangue entrainment, the column gave high concentrate grades and high recoveries.

Jan 1, 1988

By Pat DeWilliam

The Yakobi nickel-copper deposit is located essentially at tidewater in the east-central part of Yakobi Island, about 16 1 airline km (100 airline miles) west of Juneau, and can be reached by float plane and boat from Juneau and Sitka. The fishing village of Pelican, population 400, is situated 14.5 km (9 miles) to the east. An unimproved road, approximately 4 km (2.5 miles) long, connects a dock site at Lisianski Strait with the main part of the deposit known as the Basin Area (Fig. I). Other mineral occurrences are known as the Takanis, Flapjack, and Beach Areas. Another smaller nickel-copper deposit is located about 32 km (20 miles) to the south on Western Chichagof Island and is known as the Mirror Harbor nickel-copper deposit. The original discovery of the Yakobi deposit was made by S.H.P. Vevelstad about 1920 and a 47.5-m (156-ft) long adit was driven on the southwest side of the deposit in the Basin Area. The deposit was examined by J.R. Van Fleet of Union Carbide in 1930 and by J.G. Fairchild in September 1931. Stanley and Yates of the International Nickel Co. of Canada (Inco) visited the property in August or September 1937. In 1942, the controlling interest in the deposit, covered by 124 unpatented claims, was said to be held by Vevelstad and associates

Jan 1, 1991

By C. K. Blair, V. J. Hucka, E. P. Kimball

In central Utah, a coal mining operation is taking place under an 0.5-m (20-in.) pressurized natural gas pipeline. The room-and-pillar method with pillar extraction is being used to extract the coal from the seams. The pillars beneath the pipeline will not be extracted; however, there is a possibility that some subsidence may occur due to pillar failure. To assess possible damages on the pipeline, an attempt has been made to predict subsidence in the area where pillars may collapse. The resultant values of subsidence strain and slope have been used to determine the magnitude of strain, stress, and shear induced in the pipeline. Also, a network of survey points has been installed along the pipeline to detect ground move¬ment that would indicate excessive subsidence.

Jan 1, 1987

By G. I. Karydakis

Geothermal energy is an important energy asset which can play a significant role in providing energy resources to cover energy needs of a country while it can play a primary role in a particular region where it is abundant. Greece is especially rich in geothermal energy. The collision of Euroasiatic and African plates coupled with the strong tectonic tension, particularly in north Greece, resulted in the formation of important geothermal fields of low, medium and high enthalpy. These fields are in the Aegean islands, in central and east Macedonia, in Thrace and in central Greece. This work presents and analyzes information about the drilling activity for exploration and production of geothermal fields of low, medium and high enthalpy in Greece for the past thirty years. The number and type of wells drilled together with the spatial and the yearly distribution are given. Depth data has been analyzed according to the fluid temperatures and to the geological formations. Cost data are presented and analyzed for the total number of wells drilled giving also the cost per meter drilled.

Jan 1, 2006

By A. G. Belova

Conversion of coal into high-value gases via gasification offers significant pollution reduction and efficiency improvement benefits associated with controlled combustion of clean gases for power generation. However, current gasification-based electricity production technologies, such as IGCC do not address carbon dioxide emissions. The focus of the study is CO2 capture on CaO prior to combustion of coal-derived gases. To overcome kinetic and stability limitations associated with its utilization, CaO is distributed on high-surface area -Al2O3 and supported on a ceramic honey-comb monolith. The proposed method allows for efficient capture of CO2 from a gas mixture, as studied in a flow-through reactor system. This novel method of CO2 capture is used here to argue for pre-combustion capture of CO2 in coal gasification-based power plants. When CaO is present during the steam reforming of coal gasification gases, continuous withdrawal of CO2 from the system provides for higher yields of reforming products (hydrogen gas) by influencing the thermodynamic equilibrium of the entire system.

Jan 1, 2009

A form of column flotation cell is described in which the contact between the feed and the air stream is made in a mixing device at the top of a vertical downcomer. The air-liquid mixture flows downward to discharge into a shallow pool of pulp in the bottom of a short cylindrical column. The bubbles disengage and rise to the top of the column to overflow into a concentrate launder, while the tails are discharged from the bottom of the vessel. The main advantages of the device described are that the overall height of the column is reduced to about 1 m (3 ft), and the column can be self-inducing with respect to the air supply. Experimental results are given from tests on a feed stream to a conventional zinc cleaner circuit. Using wash water to reduce gangue entrainment, the column gave high concentrate grades and high recoveries.

Jan 1, 1987