Search Documents

By William L. Jude

INTRODUCTION Although the mining method described in this chapter is locally designated "modified Mitchell," there are so many features which are characteristic of square sets that the designation "modified square set" would describe the method equally well. The method was developed as a result of local operating experience with various mining methods, observing operations in mines in the southwest where Mitchell stoping had been thoroughly developed, and an exhaustive study of min¬ing methods literature. Since 1941, modified Mitchell stopes have con¬tributed over 50% of the total stope production and were largely responsible for supporting production dur¬ing the war years and period of declining manpower and increasing costs. GEOLOGY The community of Gilman is situated on Battle Mountain at an elevation of 2743 m (9000 ft) in the Battle Mountain mining district, about 45 km (28 miles) by highway north of Leadville, CO. The sur¬rounding area, including the Mount of the Holy Cross and Eagle River Canyon, is noted for its beauty and recreational facilities, both summer and winter. Massive sulfide ore bodies of the limestone replace¬ment type occur as chimneys and mantas or as blankets in strata dipping 0.19 rad (11°) northeasterly. A chimney is shaped like an inverted cone with shale, quartzite, and porphyry caprocks forming its base. This relatively impervious capping apparently blocked rising ore constituents which formed the chimneys and mantas. At the apex or lower extremity of the chimneys, the ore follows small fractures and bedding planes in under¬lying quartzite. Dimensions of chimneys vary, ranging up to 61 m (200 ft) vertically and 76 m (250 ft) horizontally near capping. The manta or blanket ore bodies vary in vertical cross section from one hundred to several thousand feet. One such manta was developed from its outcrop to its chimney source approximately 610 m (2000 ft) downdip. Another manta of substantial cross section and length did not follow shale but extended updip with limestone capping from its source at a lower horizon. All chimneys, however, make up to the shale¬quartzite-porphyry capping. Chimney ore minerals are mainly pyrite and chalco¬pyrite with accessory copper and silver minerals, surrounded by, and in places overlain with, marmatite, pyrite, and galena. Manganosiderite extends into the ore. It may or may not be impregnated with sufficient marmatite and galena to be of commercial grade. Ore may be massive, coarsely crystalline, or sandy, some¬times rubbly. Generally speaking, chimney ore masses are incompetent and of variable grade. Caprock is heavy and caves readily. Manta ore minerals are mostly marmatite, pyrite, and galena associated with manganosiderite. Structural characteristics of the ore are similar to those found in chimneys and where the manta contact shale capping the ground is unusually heavy. However, the large manta with limestone capping mentioned previously consisted of a hard strong ore mass in fairly strong host rock. Commercial ore contacts are fairly regular in this manta but in others the ore waste contacts along the walls are irregular with shaly limestone pendants extend¬ing downward into the ore at capping. Dolomite sand is also quite frequently encountered along wall contacts and less frequently overhead. MINING METHODS Practically all stoping in the Gilman ore bodies has been carried on with timber and fill methods and the features which have been briefly described have dictated the choice. Although at the present time modified Mitchell and underhand square-set stopes account for the total production, considerable production has been obtained from alternate horizontal cut-and-fill stopes with Mitchell truss stopes in the pillars. This method was highly satisfactory in the hard manta ore body mentioned earlier and where ore excavations 11 m (35 ft) wide and 23 m (75 ft) long required no auxiliary timber support. It was a pillar recovery application of the method devised by M. W. Mitchell at the Calumet

Jan 1, 1982

By Paul W. Patton, Christopher Scott Smith

The use of ceramic-in-rubber pulley lagging on bulk material belt conveyors is increasing. Many of the applications have been on pulleys originally installed with rubber lagging. There is a consensus that the fiction characteristics of the ceramic material are significantly better but the factors quoted vary, possibly because the more complex traction mechanism of the dimpled ceramic elements on the belt is not well understood. In this paper we will report and evaluate field data from a number of field installations to provide a study of actual friction characteristics in successful applications for those who desire reliable data for using ceramic-in-rubber lagging in new conveyor designs.

Jan 1, 2004

By B. W. Firth

Increasing depth in vertical mine shafts penalises conventional hoists in at least four distinct ways: rope weight becomes limiting; travel time increases; the obstruction of ventilation becomes more serious; and with friction drives, rope wear due to torque is aggravated. Travel speed is limited by instability of poorly sprung conveyances on inaccurately aligned flexible rails, and also by the cost of installed power to meet an inherently peaky demand. These problems call for a review of existing designs, firstly in respect of the furniture (Buntons and guides) obstructing the air flow, and secondly in regard to the hoist running in the shaft.

Jan 1, 1969

By Diane M. Jordan Tom M. Malloy

As part of the Mine Waste Technology Program (MWTP), a large-scale column test utilizing bacteria and a sulfide ore was conducted at McClelland Laboratories, Inc., in Sparks, Nevada. The MWTP is funded by the U.S. Environmental Protection Agency (EPA) and is jointly administered through an interagency agreement with the U.S. Department of Energy (DOE). The project was intended to illustrate the viability and feasibility of biodegradation technologies to reduce the cyanide to the regulatory level of 0.2 parts per million (ppm) within an acceptable time frame and with low operational costs.

Jan 1, 1999

By Kenneth N. Han, Yuhong Chen

The removal of carbonaceous material from Carlin gold ore has been investigated via froth flotation. The effect of type and concentration of various oils as flotation collectors and of sodium silicate as the dispersion agent on the overall recovery of carbonaceous material has been studied. Other variables affecting froth flotation efficiency were also examined closely. These included particle size, pH of the solution, and temperature. The effect of reduction and oxidation of carbonaceous material on froth flotation efficiency has also been investigated. This investigation showed that aromatic type oil was the most effective collector. Also found in this investigation was that oxidized carbonaceous material was difficult to float unless the oxidized portion was subject to reduction before flotation. More than fifty percent of the carbonaceous material was able to be removed via froth flotation. It can be concluded from this study that the effect of pH and temperature during the rougher flotation state is of little significance to the overall recovery of carbonaceous material. Since pyrite is responsible for the high consumption of chlorine, removal of pyrite is very important in order to reduce the overall consumption of chlorine.

Jan 1, 1990

By T. Szwilski

The Appalachian coal region is an area here the small mining operation dominates. The large number of small operations makes the coal industry in chat area very competitive, the industry concentration ratio being low. This feature is reflected in the nature and behavior of the coal supply and demand viz a viz the coal market. The vast majority of the small coal operations in Eastern Kentucky for example, are contractors. The circumstances under which a large mining company can elect to use contractors to supplement their coal production are examined. The pros and cons of small underground single unit mines and larger multiple unit mines are discussed.

Jan 1, 1986

By S. A. G. Poppen

The lining of a mine shaft is one of the most important considerations in the planning and operation of an underground mine. Generally, the function of a shaft lining is to preserve the shaft opening in a manner compatible with the expected mine life and -the other shaft operations. Where shafts are the only means of surface access in a mine, they also serve a critical function for the safety of the entire underground operation. Routine repairs and maintenance work on the shaft linings are only possible in stable strata with only minor interruptions to the shaft operations.

Jan 1, 1988

By Lee R. Martin, Michael R. Taber

Bird Balls™, the latest development in the ongoing battle at mine sites across North America, help to eliminate accidental avian mortality caused by birds ingesting cyanide leachate. Bird Balls™ are a 4-inch sphere made of high-density polyeth­ ylene (HDPE). They weigh 40 grams and are black in color to provide optimum life in UV intense environments. A floating blanket of bird balls totally excludes birds from a liquid surface. Federal agencies that enforce the Migratory Bird Treaty Act do not specify how to keep migratory birds out of leachate basins. Some state agencies, however, specify that a physical barrier must be in place to exclude migratory birds if cyanide levels are high enough to cause mortality. Industry standards for protecting waterfowl now include Bird Balls™ as well as net­ting, detoxification, and heap leach systems designed in such a manner that no exposed solution ponds or channels exist. Hazing is no longer an option. A bold statement to make? Perhaps, but W. R. Jeffress (1990) covers the subject well when he stated that, "Hazing techniques as a whole have not been effective in excluding waterfowl or other species of wildlife from toxic heap leach solution ponds or tailings impoundments. Research and devel­opment of the new 'Star Wars' hazing techniques, such as laser netting and radar systems, are interesting concepts and will pos­sibly offer an alternative to total physical exclusion or neutral­ization in the future. All of these methods are going to have to be thoroughly tested." For those who may want further docu­mentation, we have included a special reference section cover­ing hazing. R. J. Hallock (1990) stated that, "The Fish and Wildlife Service is particularly interested in migratory birds. In fact, a large portion of our effort, nationwide, is focused on migratory birds. Bird habitats are managed directly through the National Wildlife Refuge System and indirectly through other agency programs. We also have a responsibility to protect birds under the Migratory Bird Treaty Act. Most birds attracted to mine ponds are covered under this Act. The only migratory birds not protected under the Migratory Bird Treaty Act are English Sparrows, Starlings, and Pigeons. Since this is a treaty with five nations, the concept of acceptable losses does not apply. It is not a negotiable situation. There are a few exceptions noted in the Act, including prescribed hunting of selected waterfowl, scien­tific collection, and game bird farming. There is no exception for the loss of migratory birds exposed to solutions of cyanide."

Jan 1, 1996

By Fathi Habashi

CLAYS CONTAIN the mineral kaolinite, a hydrated aluminum silicate. It is an important potential raw material for aluminum, especially for those countries possessing no bauxite deposits. Therefore, there is no surprise to find a large volume of research done for the recovery of aluminum from clays. Kaolinite (Al203?2 SiO2?H20) contains 39.8% A1203; 46.3 % SiO2, and 12.9 % H2O. The analysis of a good-quality dried clay of an Eastern Canadian siliceous shale is shown in Table 8-1.

Jan 1, 1970

The objective of this study is to classify ore and waste in a selected mine. The support vector machine, was used for the classification purpose, is applied to a zinc ore body in a skarn deposit located in the central region of the Peruvian Andes. The input parameters used for the model are spatial coordinates and the lithological information of the ore body. The input data was divided into training and testing data sets and the performance of the model was tested using the testing data set. The results show that more than 76% of the data could be properly classified by this method. The ore waste maps of the deposit was then developed using SVM model. From the result it was observed that a comparatively very few number of cells classified as ore. The ore is concentrated in small lodes at the middle of the volume of study, and not uniformly distributed throughout the study area. The lithological map of the deposit was also constructed as it was used as an input parameter for the SVM model. The indicator kriging was used for generation of lithological map of the ore body. Key word: Ore waste classification, Support vector machine, Indicator kriging, Confusion matrix.

Jan 1, 2008

By John C. Edwards, Robert C. Bates

Modeling uranium mine radiation control methods and natural environmental radon variations is an extremely complex endeavor. A number of authors have examined particular facets of the problem and have proposed models for their area of interest. Bureau of Mines personnel brought together many of these individual studies, and from them have attempted to develop a coordinated plan for modeling radon daughter concentrations in the uranium mine environment. This approach is described.

Jan 1, 1981

By W. H. McDonald, D. D. Carr

The use of stone in building construction predates written history. From the time that stone was first used, builders have constructed stone buildings predominately from local or regional materials. However, since World War II, the stone business has become increasingly global. For example, French limestone is now sold to builders in the United States, and American granite is shipped to Japan. The internationalization of architectural and construction firms has encouraged this trend. Differences among nations in trade practices, environmental demands and the level of knowledge of dimension-stone characteristics make international trading in stone a risky and potentially disastrous business for unwary participants.

Jan 1, 1997

By C. J. Konya

When blasts are designed, the assumption is made that all blastholes release near ideal energy. In many types of mining operations, some blastholes release very little useful energy. These blastholes will be called malfunctioning blastholes. Recent studies indicate that on many types of blasting applications, 30 percent of blastholes are malfunctioning. This malfunctioning routinely occurs on the operation and is not an unusual occurrence. This paper will discuss the cause of malfunctioning blastholes and methods to minimize the detrimental effect on both safety and costs.

Jan 1, 1988

By P. E. Richardson, N. P. Finkelstein, Z. Chen

The large band gap and insulating properties of sphalerite have limited the application of standard electrochemical techniques for studying its reactions with flotation reagents. This problem has been overcome by developing electrodes that rely on the surface conductance produced when sphalerite is activated with copper or other heavy metals. A brief exposure of the mineral in copper sulfate solutions results in electrodes that exhibit significant electrochemical activity characteristic of copper sulfides. Voltammetry studies conducted on sphalerite activated in 10-4 M CuS04, solutions at pH 4.6 provide information on both the amount and the nature of the activation product(s). It is shown that copper activation is strongly dependent on the electrochemical potential applied during activation. Activation at potentials increasingly negative of the rest potential causes a progressive increase in the amount of copper on the surface; activation at potentials positive of the rest potential decreases the amount of copper on the surface. The results indicate that both the kinetics of copper uptake and, possibly, the chemical composition (stoichiometry) of the activation product are controlled by the electrochemical potential.

Jan 1, 1995

By A. Wahab Khair, Negendra P. Reddy

INTRODUCTION The continuous mining machines which were introduced in the 1950's now account for more than half the production of coal from underground mines. Unfortunately, these continuous miners which were designed for increased productivity have also increased the concentration of respirable dust in mines. Inhalation of this respirable dust by miners causes the Coal Worker's Pneumoconiosis (CWP). Concern for CWP increased in the United States following a 1963-65 survey that showed definite x-ray evidence of CWP in 9.8 percent of working miners and in 18.2 percent of nonworking miners in the Appalachian bituminous coal region (Breslin and Niewiadomski, 1982). One of the major objectives of the Federal Coal Mine Health and Safety Act of 1969 was the prevention of CUP. This law initially limited the daily average exposure of coal miners to 3 mg/m3 of respirable dust. However, following the results of a probabilistic model developed by Jacobsen, et. al. in 1971, the limit was reduced to a mass concentration of 2 mg/m3 unless quartz content exceeds 5 percent, a rare occurrence in mines. Based on x-ray categorization prior to death it is believed that the mass concentration in the respirable fraction is a parameter of primary interest for hygenic evaluation of dust exposure. Elorgan, Burgess and Jacobson (1973) suggested that the quantity of inhaled dust, although influential is not the only aspect of exposure which is significant in producing CWP. Miners working in higher rank coal (anthracite) mines are more susceptible to CWP (Morgan, Burgess and Jacobson, 1973). This also confirms the findings of the British (Bennett, Dick and Kaplan, 1979 and Hurley, et. al., 1979) and Germany (Reisner and Rubock, 1977). Based on the cy to toxicological evidence Reisner and Rubock (1979) suggested that when coal properties are similar, increasing quartz and mineral content increases toxicity. David, Ottery and Le ?oux (1975) examined that as the severity of the CWP increased the retention of the coal dust content in the pulmonary region remained the same, while that of quartz content increased significantly . Leiteritz, Baur and Bruckman (1971) studied the various components of coal dust and showed that coal particles comprised a smaller fraction of the mass of fine dust than did particles , of quartz and minerals. It is ironic that quartz and mineral matter both comprise smaller fractions of the higher rank coal dust (Dodgson, et. al., 1971 and Dwiggins, 1981). Results of a recent research revealed that quartz or any other mineral examined had no strong or consistent effect on the incidence or progress of CWP (Attfield,

Jan 1, 1986

By S. F. Hillis, J. E. Rourke, K. A. Szalay, O&apos

INTRODUCTION For the past 25 years, tunnel support requirements have frequently been determined, at least in North American practice, by classifying the rock according to the system proposed by Terzaghi (1), using one or more of the 8 Rock Conditions which he defined, the rock load then being selected within the range given for each Condition. However, there is a lack of published data comparing Terzaghi loads with actual measured rock loads, and it would appear that the degree of conservatism, or otherwise, of the Terzaghi approach is very often unknown. Excavation of 4 large diameter tunnels at the Tarbela Dam Project in Pakistan afforded an opportunity to compare Terzaghi and measured loads, through instrumentation of the steel ribs installed for temporary support, and by classification of the geology exposed during the tunnelling operations. In addition, the deformation of the rock surrounding the tunnels was monitored during excavation by means of borehole extensometers installed prior to the start of tunnelling. This paper describes the tunnel instrumentation and the results obtained therefrom, and relates these results to the Terzaghi load coefficients. It also discusses the effects of the methods of excavating the tunnels on the rock loads and rock deformations. PROJECT DESCRIPTION The Tarbela Dam Project is located on the Indus River in

Jan 1, 1974

By R. Pakalnis

This paper compiles the research work conducted by the Spokane Research Laboratories in the investigation of shotcrete within underground mines to the applied design of ground support for the operator. It looks at the design methodology in terms of employing shotcrete as a fabric to confine the rock mass between the individual bolts as dictated by empirical charts. The failure mechanism in terms of its implication on design is presented with respect to the design of 6m wide tunnels for temporary and permanent openings within weak rock masses. This is reflected by field observations that relate laboratory tests to the onset of failure for the operator in order to provide guidelines for design and monitoring. This is coupled with guidelines for safe entry in terms of cure times as well as the understanding of the behaviour of the shotcrete in terms of fibres and the overall strengths that result with respect to the design of the mine openings. This enables the operator to better understand his workplace thereby provide a safer work environment.

Jan 1, 2010

By W. J. Cieslewicz

Geologically, northeastern Siberia is a region occupied by a folded belt of Triassic and Jurassic sediments and volcanics. Gold mineralization is of Upper Jurassic age. Most of the stream placers formed during the Quaternary. Placer gold was first discovered in 1916. Between 1930 and 1957, mining was carried out by the "Dal 'stroi," a Russian concentration camp organization. Since 1966, the mines have been worked mechanically. About 10 mining districts are now active, producing, altogether, 110 to 135 t (120 to 150 st) of gold annually.

Jan 1, 1987

By T. Malterer, R. Adams

Peat has unique physical, chemical and biological properties. These include high porosity and water retention, high absorption and adsorption properties, and high buffering capacity. In addition, peat is a rich medium for microorganism activity. Peat has traditionally been used for horticultural purposes. However, in recent years, peat is increasingly being used for waste- treatment purposes. This paper reviews North American literature on the use of peat for waste-treatment applications. The literature indicated that peat has potential for use in the treatment of municipal and on-site effluents, for the removal of low concentrations of heavy metals and for the adsorption of liquid and gaseous hydrocarbon pollutants.

Jan 1, 1997

By Chris Cox, David Green

Outokumpu has developed the HG or High Grade flotation cell over the past decade. This machine gives upgrading and selectivity performance superior to conventional mechanical cells while maintaining their simplicity, ease of operation and recovery characteristics. The HG design is available in a tank cell configuration which provides a number of benefits in plant design and operation. This paper will describe the HG Tank Cell and the "Virtual Column" concept. Results are given from the operation of the HG Tank Cells at Lac Minerals - Est Malartic in Quebec, Canada. Further discussion of applications for gold recovery is also provided.

Jan 1, 1993