Search Documents

By K. Professor Heiskanen

The improvement of grinding circuit efficiency is a constant industrial requirement. It has often been connected to the improvement of classification. The paper discusses some operational aspects of hydrocyclone classification. A hydrocyclone should be operated close to roping but should not with high density slurries go to roping. Unfortunately roping is not well understood and roping models for controlling hydrocyclone operation are not adequate. The paper discusses also some ways of improving the classification in terms of bypass and imperfection. The last part of the paper discusses the effect of bypass and imperfection on circuit performance.

Jan 1, 1997

By Jon G. Baird

The suggestion of the use of measurements of trace amounts of mercury as a guide to the location of sulphide ore deposits was first made by the Russian, A. A. Saukov (1), in 1.946. Since Saukov's original work, many others have studied the abundance of mercury in nature, the association of mercury with sulphide ores and methods by which very minute quantities of mercury can be measured in air, soil, rocks, water and plants. The most abundant of the mercury bearing minerals is cinnabar (HgS). Native mercury is also found and sulpha-salts like tetrahedrite are known to have important mercury contents. Other sulphides of base metal deposits contain mercury in amounts ranging from parts per million to as much as one or two percent. (2) The mercury content of sulphide-free rocks is usually less than a few hundred parts per billion (1 ppb - 10-9), Soils usually contain less than 100 ppb and water less than 1 ppb of mercury. Normal atmospheric air contains about 1 nanogram (10-9 grams) of Hg per cubic metre although higher concentrations can be observed near mercury occurrences, sulphide deposits and volcanic exhalations.

Jan 1, 1973

By J. J. Bartels

The phosphate rock review did not arrive in time for publication in the. June issue. The world phosphate industry continued its slide in 1992 from the already depressed levels in 1991. The industry is locked into a 30-year fertilizer price low due to the worldwide fertilizer glut. Domestic production and imported, marketable phosphate rock decreased 1%, while domestic consumption increased by 1 % last year. The US Bureau of Mines reported a decrease in the domestic phosphate rock value from $25.42/t in 1991 to $23/t in 1992 ($23.06/st to $20.80/st). The diammonion phosphate (DAP) product price also dropped in value from $138/ t in January 1992 to $11 0/t in December ($125/st to $99.70/st). Continued declines in DAP prices is forcing the US fertilizer industry to develop cost-saving programs and reorganizations. Layoffs in 1992 resulted in a 7.6% decrease in the Florida phosphate workforce. Since 1980, the Florida workforce has declined by 35%. Small phosphate companies were forced to close operations or were sold to larger phosphate companies. Federal and state environmental regulations for byproduct waste disposal methods are being studied. The Environmental Protection Agency (EPA) approved phosphogypsum use in agri¬cultural and research applications as long as the radium 226 concentration is lower than 10 pci/g. The EPA is also reviewing regulations concerning air emissions at fertilizer plants. Industry publications reported the possibility of continued company sales and mergers in 1993. Industry expectations are optimistic while waiting for an upturn in the market. The US phosphate industry consolidation into three or four major companies should evolve into a stronger world market force.

Jan 1, 1993

By M. J. Senk, A. Lusin

Federal regulations require that methane liberated at the face be diluted and removed to maintain methane gas concentrations below 1pct (CFR) in working places and intake air courses. The delivery and distribution of intake air at the face is critical for effective face ventilation. Improved techniques for monitoring the movement of intake air to the face are needed. A test system was developed and a computer program written for using a three-axis ultrasonic anemometer to measure airflow in a simulated mine entry. Results of tests conducted in the entry showed that the anemometer is a valuable tool for measuring mine airflow conditions near the face.

Jan 1, 2003

By E. Topuz

Mining equipment, like all other equipment, is subject to failure. Since most failures occur at random and are unexpected, corrective maintenance is usually more expensive and causes more down-time than preventive maintenance. In order to reduce the number of failures and thereby increase the availability of an equipment or system, preventive maintenance can be scheduled at predetermined points of time. The preventive maintenance scheduling policies presented in this paper utilize reliability and probability theories. They can be applied to various production bottlenecks where high cost equipment precludes having sufficient quantities of stand-by units.

Jan 1, 1982

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

GENERAL STATEMENT Data frequently can be collected by several dif¬ferent methods. The method required for the nec¬essary precision for inflow prediction to mines should be selected and other methods avoided. Pre¬cision monitoring or measuring techniques fre¬quently require more time, expertise, and expense in their implementation that may not be justifiable. The temporal distribution of the data needs also may dictate the method used for data collection. Continuous recording devices may be required for time sensitive data whereas point measurements of other parameters may be adequate. Data needs will vary as the hydrologic investigation proceeds. In¬itial data needs may require only a qualitative col¬lection of data such as the areal distribution of precipitation. Subsequent data needs may require the measurement of ground water levels to the near¬est hundredth of a foot. Data requirements can be difficult to fulfill for ground water systems. This is particularly true for anisotropic, heterogeneous hydrostratigraphic units since the hydrogeologic parameters vary both ver¬tically and areally. Techniques exist for determining the storage characteristics of both unconfined and confined hydrostratigraphic units but these pro¬cedures require the installation of multiple wells in the same unit which may be impractical. Specific tests are discussed subsequently that permit the determination of vertical hydraulic conductivity. Data collected from field procedures or tests are generally preferred to laboratory derived data. This is especially true for hydrogeologic parameters such as hydraulic conductivity. SURFACE WATER SYSTEMS Precipitation Precipitation data can be collected from sources that maintain a historical record. The US Depart¬ment of Commerce, National Oceanic and Atmos¬pheric Administration (NOAA), maintains weather observation stations across the country. Such a sta¬tion frequently can be found near a proposed mine site but the type of weather data collected varies from station to station. Fortunately, precipitation data are collected ubiquitously. The data collected by NOAA can be purchased for the area of interest in the form of monthly and annual tabulations. Private weather stations constitute a second source of precipitation data. Existing data usually are analyzed by one of three methods. The station average method merely sums the depth of precipitation at each station and divides the sum by the number of stations as fol¬lows: [ ] where Pavg is the average precipitation (L), P, is the depth of precipitation at station i (L), and N is the total number of stations. This method is applicable where there are a relatively large number of stations uniformly distributed across the area (Hjelnfelt and Cassidy, 1975, pp. 71-72). The second method, called the Thiessen poly¬gon method, weights the precipitation at each sta¬tion in direct proportion to the area it represents without consideration of topography. The stations are plotted on a map and perpendicular bisectors are drawn on the lines connecting the stations. The polygons formed by these bisectors constitute the area that the precipitation for that station repre¬sents. The overall precipitation can be calculated with the following equation:

Jan 1, 1986

By Abdullah Arik

The resource classification methodologies have always been a topic of research and debate. There are both traditional and Geostatistical methods used in practice. Because of the uniqueness of each ore deposit, it seems almost impossible to have a single industry-accepted norm for resource classification. Therefore, some practitioners have adapted the methodologies to suit the deposits they are working on, but many simply use the methods they are comfortable with. Another reason for the existence of varying classification methodologies is the lack of an easy and established way to measure the confidence in the estimates. Therefore, their classification becomes a subject of debate. In this paper, a new approach is offered to classify the resources using a "Resource Classification Index." The approach using this index takes into account the local variation, the spatial data configuration around the block being estimated, as well as the traditional distance measures. A case study for a gold deposit is presented to demonstrate how this new index can be used to classify the resources. The results from this approach are compared to those from two popular classification methodologies.

Jan 1, 2002

By J. M. Scharer, Bruce E. Halbert, Lysane Bouduc, Douglas B. Chambers, Jennifer L. Kirkaldy, Carol M. Pettit

Io contrast to acid mine drainage (AMD), neutral mine drainage (NMD) has not yet received widespread attention. Metal and sulphate concentrations can be elevated and of concern in neutral drainage from waste rock and tailings. In the present paper, metal release in high ionic strength mine drainage at neutral pH is evaluated at several mine sites. Specific factors including oxidation rates, buffering capacity, and hydrology are also addressed and their effect on the production of contaminated NMD from mine wastes is evaluated. Case studies are presented involving current seepage water quality and predictive geochemical modelling to illustrate the possible time frame and magnitude of the contamination.

Jan 1, 2000

By D. L. Misterek, E. J. Slebir, G. W. Ring, M. A. Laird

INTRODUCTION In 1973, the Federal Highway Administration (FHWA) initiated a 10-year program of research on tunneling technology for future highways as a part of a larger Department of Transportation effort on tunnels. The objectives of the FHWA program are to: improve tunnel design technology, reduce costs, minimize adverse environmental impact due to construction, increase the rate of construction, and assure the maintenance of a safe and attractive tunnel environment. The program is divided into four research tasks designed to solve tunneling problems identified by the engineering and field offices of the FHWA. These tasks are as follows: 1. Cut-and-Cover Tunneling 2. Site Investigations 3. Ground Movements - Prediction and Control 4. Highway Environmental Criteria for Tunnels In order to provide input into Tasks 2 and 3, the FHWA is sponsoring an investigation and testing program by the U.S. Bureau of Reclamation to instrument and monitor two sites in the second bore of the Eisenhower Memorial Tunnel located on Interstate Highway 70 at Loveland Pass approximately 97 km (60 miles) west of Denver, Colorado. The tunnel will be approximately 14.0 m (46 ft) in diameter when excavated. The study is designed to generate data on: (1) changes in the state of stress, and movements during and after tunneling, (2) tunnel lining design requirements, (3) developing a

Jan 1, 1976

By Thomas F. Pugsley, Wilf J. Davies, James Gallagher

Falconbridge Limited is developing a major nickel mine at Craig which lies between 600 m, 915 m and 1500 m below surface and is accessed on the 600 m and 1250 m levels of Onaping Mine. To supply adequate ventilation for mine development and initial ore production, two raises, 1200 m long are to be driven in norite and granitic gneiss. Falconbridge has purchased a Robbins 97RL Raise Drill and a string of 330 mm drill pipe to ream these raises in 600 m legs at diameter. The paper describes the introduction of deep hole, large diameter raise boring technology into Falconbridge operations involving contractors and specialists in the technology.

Jan 1, 1989

By D. A. Peterson

Laboratory testing was completed to determine the effectiveness of a fiberglass cable bolt (FCB) as a cuttable rock support for a continuous, hard-rock mining method. The FCB consists of four Polystal tendons combined in a node/antinode fashion, with polyvinyl chloride (PVC) spacers forming the anti-nodes. The largest ultimate pull-out load achieved by the FCB was 22 t (48,400 lb) at 89% of the tendons' theoretical pullout load. This premature tendon failure is accredited to: • differential stresses within the tendons and • differential tendon displacement. An increase in pull-out resistance for a given embedment length is due to: • increased bond area, • reduced interfacial shear and • "wedge" effect. The critical embedment length was found to be 40% less than for conventional steel cable bolts (SCB) at a 127-mm (5-in.) node spacing. An FCB can have up to a 92% increase in load-carrying capacity over a conventional SCB at equal embedment lengths. The load carrying capacity is equivalent to SCB at a 960-mm (37.8-in.) embedment length. Though the FCB is 7.5% more expensive than the conventional SCB (installed), this cost may be offset by increased performance. FCBs are a potentially viable support alternative for continuous hard-rock mining.

Jan 1, 1993

By Joseph G. Wargo

The purpose of this paper is to investigate trends in exploration expenditures of a selected group of mining companies for the interval 1968 through 1971. The paper also compares these trends with other financial factors that are associated with various groups of companies and comments on the implications of these trends. Although a four-year interval is hardly enough time to establish a long-range set of trends from which operating rules can be derived, the fact that the four years selected are in the immediate past gives some sense of relevance to the matter of exploration expenditures at the present time and in the near future. The sample under study here consists of 21 mining companies. Of these, 19 are listed on the New York Stock Exchange and 2 are listed on the American Exchange. Twenty are American, one is Canadian. All are fundamentally "mining companies" in that they derive the bulk of their income from the extraction, sale, and at times, fabrication of metals from their own mines. This is in contrast to companies which have mineral exploration departments but derive the bulk of their revenues from sources other than mining; for example, from oil and gas sates, Also, no companies which can be considered strictly as exploration companies are included in this study. Although this definition held up fairly well when studying this list in 1968, the strict application of this definition became more difficult through the years up to the present time. In 1971, three or four of the companies were changing their character in that they were phasing out of the mining business, and either deriving their income or planning to derive a substantial part of their income from activities other than mining. A study of

Jan 1, 1973

By M. Mohammed, S. J. Jung

The prime criteria in the design of underground openings with complicated geological structures is ground control. Stability of underground openings for deep mines is critical because incorrect orientation or geometry of the shaft, stopes and accessways often results in the failure of openings due to high stress conditions. Current design procedures for complicated orientation and geometry of mines are rapidly becoming inadequate. In this study, the finite element method (ANSYS) has been used with optimization criteria to design safer, more stable underground openings.

Jan 1, 1995

By H. C. Verakis

Permanent ventilation controls such as stoppings, overcasts, and undercasts for use in coal mines are required to meet MSHA’s safety standards for fire endurance and flexural strength. Due to technological advances in materials and their design for use as ventilation controls, an engineering program was established to evaluate newer or “nontraditional” ventilation controls. The program is intended to assist manufacturers, enforcement personnel and mine operators in determining if “nontraditional” ventilation controls, for example plastic membrane construction and lightweight block, meet the prescribed safety standards. The program is presented with a description of required tests and examples of products evaluated.

Jan 1, 2003

By Alex Ruzycki

Gold Fields-Mesquite is a 7.5 million ton per year heap leach operation located in the Maj ave Desert of Southeastern California. Extraction of gold is carried out on multiple lifts, with over 33.3 million tons of ore leached since the inception of operations in 1985. The delineation of the gold left in heap residue is a formidable task. Gold removed from active leach areas can be routinely monitored through sampling of emerging solutions but exact recoveries from specific heaps remains nebulous due to factors such as cross flow between sections buffering effects from multiple lifts, and releaching. In order to better quantify ultimate heap recoveries and increase releach efficiency, Mesquite initiated a residue drilling program. The project progressed through an evaluation of sampling protocol, drilling of residue by reverse circulation, entry of assays into a software package capable of producing grade-based contour maps, and a production scale releach test that evaluated the system's ability to predict residue grade.

Jan 1, 1992

By B. Denby, R. Hollands, S. Cooper

Augmented Reality (AR) is a technology that can be used to mix computer-generated images of data with views of the real world. The University of Nottingham is developing AR technology in a major research project which can be used to assist mining companies in visualising complex mine data whilst out in the field. The technology comprises of integrated GPS surveying technology and electronic orientation devices to provide location and viewing information, video capture via digital camera and portable computing hardware to overlay 3D models on views of the real world. The paper describes the concepts of the technology in some detail and concentrates on the possible applications of this in the surface mining and exploration industries.

Jan 1, 2002

By N. ?peh

The purpose of the paper is to present a way of assessing nonrenewable lignite resources by means of sustainability indicators. An introductory presentation of the origin and characteristics of the discussed nonrenewable natural resources is followed by the study and analysis of separate sustainability indicators. Out of many, only the ones that would directly relate to the explored coal deposit were studied. Some different viewpoints such as economic, social and environmental were assessed inside the studied landscape structure and in relation to other provincial resources using the indicators that are closely linked with the explored lignite reserves. Exploitation of coal as an underground nonrenewable natural resource, has been taking place in the ?alek valley for more than 120 years. However, about 60% of the coal will still be left underground since not all coal will have been extracted when the mine closes. According to the regional and wider national strategic goals concerning the use of natural resources and electricity production in the future, the sustainable aspect of the exploitation of the geologically well explored reserves is emphasized in the paper. Finally, we have tried to evaluate the role and the meaning of the studied underground natural resources for further sustainable development of the ?alek valley and placed stress on the most questionable spheres that should be considered preferentially.

Jan 1, 2007

By Takeshi Shinohara

It is a great honor and pleasure for me as President of the Japanese Tunnel Association to send greetings to the 1974 Rapid Excavation and Tunneling Conference. Recently in Japan, the Japanese Tunnel Association was established as recommended by the OECD Advisory Conference on Tunneling. This is a central organization concerned with tunnel construction consisting of government authorities, universities' research institutes and construction firms as well as manufacturers of relevant materials and equipment. As I was chosen the first president of the newly-established Japanese Tunnel Association, I would like to avail myself of this opportunity to announce to you its establishment and its earnest wish to contribute to the development of tunneling technique not only in our country but also all over the world. At the same time, I cordially request your friendship and cooperation for the benefit of further development of tunneling techniques on both sides of the Pacific. At present, many tunnels are under construction in Japan. The total length of tunnels under construction for railways and highways is about 600km including the 54km Seikan Undersea Tunnel which connects the Main Island and Hokkaido. Naturally, for construction of such tunnels in Japan, we have introduced much equipment and technique from the United States and other foreign countries. Now with accumulated experience, we are confident to be able to furnish various useful information concerning tunnel construction.

Jan 1, 1974

By Roe-Hoan Yoon

INTRODUCTION In 1960, coal accounted for 49% of the world energy consumption, an amount that was reduced to 29% in 1973 because of the availability of cheap oil. At that time, it seemed that oil would remain available for a long time in unlimited quantities. However, this situation changed drastically in 1973/74 when a series of closely spaced price increases from $3 per to $12 per bbl by mid-1974 hit both industrialized and developing countries. Another sharp price increase in 1979/80 to the $34 to $38 per bbl level also hit the world economy hard and, at the same time, set in motion powerful technology development forces for increased coal utilization. At this point, the price of coal was approximately $1.50 per MM Btu, while that of oil approached $6.00 per MM Btu. This huge price differential offered an incentive for developing new coal technologies including liquefaction, gasification, fluidized bed combustion, coal-water mixture (CWM), etc. The CWM technology was of particular interest to the utility industry, which consumes more than 80% of the coal mined in the US for power generation. In this technology, a powdered coal is mixed with water to produce a stable slurry that can be stored for an extended period of time without settling and is readily pumpable. Various reagents in the amount of approximately 1% by weight of the coal are added to inhibit sedimentation during storage and to reduce the viscosity for atomization in burners. The coal loading is in the range of 50 to 80% solids, depending on the particle size and its distribution. With very fine particles, it is difficult to increase the coal loading above 50%, and a binomial distribution helps increase the coal loading. The presence of water consumes a relatively small amount of the heating value of the coal during combustion; for a coal-water slurry containing 30% water, less than 5% of the calorific value of coal is usually consumed due to evaporation. The major advantage of burning coal as a slurry is that many of the oil-burning furnaces can be converted to coal-burning with a minimum retrofit cost. Considering the substantial price margin between coal and oil, the pay- back period for retrofit costs can be relatively short. Nevertheless, the retrofit cost can be further reduced if low-ash coals are used as feedstocks for CWM; there will be savings in the capital cost of installing bag filters or electrostatic precipitators that are designed to remove the ash from the combustion gases. Furthermore, the use of low-ash coals can minimize derating of boilers because the velocity of the combustion gases can be maximized without creating erosion

Jan 1, 1991

By B. K. Gupta

Arch Mineral's Captain Mine has used the Bucket Wheel Excavator System(BWE) for over 3 years in conjunction with a 180 yd3 (138M3) stripping shovel. The bucket wheels prestrip the soft overburden ahead of the shovel. This soft overburden is brought to the spoil side through a series of shiftable conveyors and placed by a spreader over the ungraded or partially graded shovel spoils. The placement of the soft overburden and top soil is accomplished in a manner that meets the reclamation mandates. The prestripping by the BWE has reduced the incidence of the highwall and spoil slides, depth the stripping shovel has to dig and the volume handled by the pullback draglines.

Jan 1, 1984