Search Documents

By Günther M. Volkmann

"INTRODUCTION The construction of the BAB 44 motorway between Kassel and Herleshausen (both Germany) is an important part of the trans-European road network. After its completion, the A 44 will permit an efficient connection of the Benelux States in the West and Poland in the East. In the section between Eschenstruth and Hessisch Lichtenau the Hirschhagen Tunnel is constructed with a length of 4.1km. Most sections of the tunnel are situated in weak ground conditions. Hence a combination of face bolts with spiles (short forepoling) or pipe umbrellas (long forepoling) additionally support the tunnel heading on a regular basis This article will focus on the application of a newly developed method to connect the pipe umbrella support, which is mostly installed by conventional drilling machines nowadays. The installation method limits the outer diameter to a maximum of 168mm and a pipe wall thickness of 12.5mm because workers must be able to handle pipes and its drill steel. Typically these pipes are connected with threads that create a weak link in the support system so during the last decade alternative connection systems were developed to overcome this disadvantage. One of these alternative coupling systems is the so called Squeezed Connection, which will be explained in this article followed by a discussion of its advantages and disadvantages regarding technical specifications, construction time, and safety issues. THE HIRSCHHAGEN HIGHWAY TUNNEL The German highway A 44 directs from Aachen through the Ruhrgebiet to Kassel (all Germany) and it is extended to Herleshausen (Germany). The new section connects the A 7 to the A 4 after completion. This upgrades the east-west highway connection starting at the Benelux Union and heading to Poland so it is an important part of the trans-European road network. The newly constructed section has a total length of approximately 63 km and comprises 13 tunnels. All tunnels are constructed as double tube tunnels with 2 lanes and emergency sidewalks on both sides and 14 emergency cross passages. The Tunnel Hirschhagen starts in the north of Eschenstruth and ends near Hessisch Lichtenau (Figure 1). The length of the northern tube is 4,147 m and that one of the southern tube is 4,204 m. So it is the longest tunnel of the A 44 and the second longest highway tunnel in Germany when it is put into operation. On its alignment it crosses underground the Losse valley with the state road 7, the streetcar Kassel-Hessisch Lichtenau and the Losse stream. The cover above crown varies from 10 m to 95m and it is the lowest when crossing the Losse stream."

Jan 1, 2016

By F. Dahl, P. Raleigh, J. Holzhauser, B. Nilsen

Tunnel excavation using tunnel boring machines (TBMs), has become increasingly common in recent years, despite the fact that precise evaluation of certain risks have not kept pace with the use of these machines. One of the risks easily overlooked by Engineer and Contractor alike are the effects of abrasive ground on the costs and schedule of a given project. The impacts of worn and damaged TBM cutter heads have been observed on hundreds of tunnel projects around the world. It would appear that a reliable prognosis of the abrasiveness of soils on a project would be of great importance for designers, clients and contractors alike. Several well acknowledged test and prognosis methods already exist for rock, however there is only very limited knowledge available to describe the abrasiveness of soil and its impact on soft ground TBMs. This paper will examine approaches to this problem and suggest a new approach based on a current project undergoing design.

Jan 1, 2007

By P. A. Plunkert, D. E. Morse, L. McCartan, J. F. Papp

The mineral sector is a fundamental part of the U.S. economy. It contributes to the real gross domestic product (GDP) at several levels — basic (mining), intermediate processing, manufacturing of finished goods and construction. The real GDP during 2004 increased by 4.4 percent. The nominal GDP was about $11.7 trillion. Housing starts were up by slightly more than 4 percent for the year. And the nation’s unemployment rate decreased to5.5 percent in 2004 from 6 percent in 2003. Interest rates continued to be low (prime rate was 5.25 percent at the end of 2004) but have risen gradually, following rising inflation.

Jan 1, 2005

By C. Pritchard

John Marks said in his acceptance of the Hartman Award in 2008 ? ?I guess that without the occasional complaint, your mine is probably over-ventilated? (Marks, 2008). Miners are seldom in this situation and often spend much of the time trying to find enough air to keep the operation running. With examination there are some things that can be done to make the best use of ventilation systems. Should there be surplus air, in which some of these options may result - financial and other benefits can be obtained. Some of the issues mine operators have needed to address recently are increased airflow requirements to dilute diesel particulates in metal and non-metal mines. Also, operations are faced with demands from reserves that are deeper, hotter and further away from fans and shafts, not to mention increased production demands. Mine ventilation air is a costly commodity, especially by the time it has been heated or cooled and moved to the bottom of the shaft and through the mine airways. Most of the options presented in this paper are useful for metal non-metal operations but some may be applicable to coal too. OPTIONS FOR IMPROVEMENT Some of the areas to be addressed are shop ventilation methods, auxiliary equipment areas, dedicated intakes and returns, optimizing development, examination of mine airway utilization and alternative ventilation methods. UNDERGROUND SHOPS First, examine what is being done with the underground shop air. If it is being coursed directly to the returns there may be some potential to better utilize this, in most cases, relatively contaminant free air. Research the legal options for ventilating mine shops. MSHA regulations in 30CFR 57.4761 (1) allow the following options: To confine or prevent the spread of toxic gases from a fire originating in an underground shop where maintenance work is routinely done on mobile equipment, one of the following measures shall be taken: use of control doors or bulkheads, routing of the mine shop air directly to an exhaust system, reversal of mechanical ventilation, or use of an automatic fire suppression system in conjunction with an alternate escape route. The alternative used shall at all times provide at least the same degree of safety as control doors or bulkheads. Discussion This regulation gives some operators flexibility in ventilating underground shop facilities. If shop air is to be coursed through the work area, and then directly to the mine return, the question should be asked ? is the quality of air good enough to be reused in the mine, and if so, what are the risks? Can the risks be accommodated and managed to accomplish the change? If so, a considerable increase in mine level airflow could be attained by reusing shop air. Clearly, regulations are a minimum standard, and can be exceeded. Metal non-metal mine regulations are not as specific as coal due to the multitude of different mining methods and conditions utilized. Risks must be thoroughly examined and addressed to assure a safe environment. Issues Determine what contaminants are being produced in the work area ? welding fumes, diesel exhaust, paint fumes, chemicals and solvents, etc. Survey the area and determine exposures. MSHA requires exposure monitoring in 30 CFR 57.5002 (1) of dust, gasses mists and fumes to assure air quality is being met. Perform surveys and examine existing data to quantify personal and area concentrations of contaminants. Often there is adequate circulation such that exposure levels in shop work areas are low. After sending shop air back into the system any contaminants would be further lowered by dilution with other mine intake air downstream. Look at the shop work schedule. If only on day shift, the other two shifts and possibly weekends have no activity or source of contamination to affect the ventilation system. The worst case planning scenario would be a shop fire. Study and simulate how this would affect the mine and shop area. MSHA regulations require an escape route and a fire suppression system be installed and maintained as follows in 30 CFR 57.4671 (1): (d) Automatic fire suppression system and escape route. If used as an alternative, the automatic fire suppression system and alternate escape route shall meet the following requirements: (1) The suppression system shall be? (d)(1)(i) Located in the shop area; (d)(1)(ii) The appropriate size and type for the particular fire hazards involved; and (d)(1)(iii) Inspected at weekly intervals and properly maintained. (2) The escape route shall bypass the shop area so that the route will not be affected by a fire in the shop area. Case Study In an underground room and pillar mine, active mine workings were advancing further away from the mine shaft with deteriorated returns and leakage having a negative effect on ventilation airflows to the face. Mine level airflows were 236 m3/s (500,000 cfm) and shop airflows were 24 m3/s (50,000 cfm) (see Figure 1A). No additional capacity was available at the main surface fan. A solution was to utilize the shop air then send it to the mine areas instead of directly to the return. Considerable information on shop air quality and exposures from many years of operation was examined and no negative data was discovered. A risk analysis determined that moving forward with a shop air reuse program was desirable. A plan was developed, analyzed and decision to proceed approved by mine management. The change was simulated on the computer with the USBM/MTU MFire program before being implemented. This included utilizing fire scenarios to examine potential exposures to inby mining sections and plan escape routes. A monitoring system was designed and installed in cooperation with the US Bureau of Mines to monitor carbon monoxide

Jan 1, 2009

By Tim O’Neil

The search for precious metals opened up the American West. And Nevada was right in the heart of this development. In the mid-19th century, prospectors seeking gold roamed the hills of Nevada and discovered the ComstockLode. The development of this huge silver and gold deposit began in1859 and was responsible for Nevada’s early entry to statehood. Mining was Nevada’s first industry. In more recent years, the Nevada mining industry has led the nation in gold, silver and barite production. Nevada also produces many other minerals. These include aggregates, clays, copper, diatomite, dolomite, gypsum, lime and limestone, lithium and magnesium compounds, perlite, salt and silica. Even today, Nevada’s mining industry continues to be a major economic force in the state. The mining industry has made more than $10 billion in capital investments in Nevada since 1985. And the value of Nevada’s mineral production last year was about $2.7 billion.

Jan 1, 2000

By D. R. Willmer, E. J. Haas

As national and international health and safety management system (HSMS) standards are voluntarily accepted or regulated into practice, organizations are making an effort to modify and integrate strategic elements of a connected management system into their daily risk management practices. In high-risk industries such as mining, that effort takes on added importance. The mining industry has long recognized the importance of a more integrated approach to recognizing and responding to sitespecific risks, encouraging the adoption of a risk-based management framework. Recently, the U.S. National Mining Association led the development of an industry-specific HSMS built on the strategic frameworks of ANSI: Z10, OHSAS 18001, The American Chemistry Council’s Responsible Care, and ILO-OSH 2001. All of these standards provide strategic guidance and focus on how to incorporate a plan-do-check-act cycle into the identification, management and evaluation of worksite risks. This paper details an exploratory study into whether practices associated with executing a risk-based management framework are visible through the actions of an organization’s site-level management of health and safety risks. The results of this study show ways that site-level leaders manage day-to-day risk at their operations that can be characterized according to practices associated with a risk-based management framework. Having tangible operational examples of day-to-day risk management can serve as a starting point for evaluating field-level risk assessment efforts and their alignment to overall company efforts at effective risk mitigation through a HSMS or other processes.

Jan 1, 2016

By D. Blackwell, W. R. Reed, G. Ross, S. Peters, M. Shahan

Dust collectors for roof bolting machines generally use a dry box to collect the roof bolting material. Recently, an underground mining operation converted a dry box dust collector to a wet box dust collector with a unique exception from MSHA for testing purposes.Water is routed to the roof bolter fromthe main water line of the continuous miner. The wet box utilizes a water spray to wet the incoming material. Testing was conducted comparing the two different collector types. Respirable dust concentrations surrounding the roof bolter with the different collection boxes were similar. The main difference in respirable dust concentrations occurred when cleaning the dust boxes. The average respirable dust concentration during cleaning of the wet box was 0.475 mg/ m3, and during the cleaning of the dry box, the average respirable dust concentration was 1.188 mg/m3, a 60% reduction in respirable dust concentration. The quartz content of the roofmaterialwas high, ranging from 28.9 to 52.7%during this study. The results from this study indicate that using the wet box as a collector reduced exposure to respirable dust up to 60% when cleaning the collector boxes.

Aug 26, 2020

By VIVEK KUMAR HIMANSHU, Murari Prasad Roy, Kaushik Dey, Rakesh Kumar Singh, Ashish Kumar Vishwakarma

Sublevel stoping is the most popular and practiced mining method in underground hard rock mines. Proper planning and its execution is the key requirement for stope extraction using this method. The stope extraction has been a challenging task since decades. The major reason is the unavailability of free faces as compared to opencast bench blasting. The geological and geotechnical parameters change gradually even within the stope itself. So, the blast design parameters should be planned according to the scenario of the upcoming ring. The blast design parameters like burden, toe spacing, inclination of blastholes, diameter of blastholes, charge density of explosive, etc., play an immense role in the rock damage. For the proper breakage of rock, the movement of burden is the prime objective. To study this, an explicit dynamic based modeler of M/s Ansys was used. The burden values were varied from 20 to 65 times of blasthole diameter to assess the optimum burden value during the study. The models were simulated for the rock having uniaxial compressive strength as 35 MPa and 102 mm blasthole diameter. Three holes were simulated having depth around 14–14.5 m. Different blast design parameters and respective blast-induced ground vibration have also been measured at the experimental site. The core samples of the rock present at the experimental site have been used for the evaluation of geotechnical parameters. These geotechnical parameters were used in the simulation models. The volume of rock excavated along the free face has been calculated in each model by varying the burden. It has been found that the burden value can varies from 35 to 40 times blasthole diameter (3.6–4.1 m) to achieve a greater volume of rock along the free face for 102 mm blasthole diameter and rock of 35 MPa uniaxial compressive strength.

Dec 22, 2023

By Iain Weir-Jones

The efficient operation of an open pit mine presupposes that the slopes are maintained at an angle which closely approaches that of the ultimate stability of the slope. In order to do this in a safe manner, it is essential that the data relating to the behavior of the slopes be monitored and made available, through an instrumentation system, to the appropriate personnel so that soundly-based engineering decisions may be reached with the minimum of wasted effort. In addition to simply detecting potential failures, the system should also define what type of failure is developing; i.e., rotational, wedge, or dilational failures. Providing this data is the prime function of a stability monitoring system. Therefore, in an operating open pit mine, the instrumentation system must provide information which will have a direct bearing upon both the safety and the economics of the operation, as well as provide data which is pertinent to initial design, or to the re-design of slopes where developing instability is found to be a problem.6 It is possible to excavate pit slopes which will remain stable under extremely adverse conditions; however, such slopes would usually be so flat that they would tend to render the operation of a pit uneconomical which might otherwise be mined at a profit. On this basis, all practical pit slopes must be considered to be, to some ex- tent, unstable; if they are not, the design is too conservative and the mine is not returning its maximum profit. To reduce the problem to its fundamentals, one can simply state that the ideal pit slope design produces a slope which stands with zero maintenance for the entire life of the pit and then collapses into the final excavation as soon as the personnel and equipment have been removed. Such a design is impossible to achieve, but the fact remains that an efficient slope would hover on the edge of failure for the life of I the pit. As one retreats from this position, the profitability of the mine decreases because of an unduly conservative design.

Jan 1, 1975

By Jr. Bacon

Kaolin clay is one of the yeoman minerals. It sees duty in almost every aspect of our lives: -in and on most paper products (from modern newsprint to National Geographic and packaging board) sometimes as much as 25% (by weight) of the product -40% of the tile (ceramic, rubber, and linoleum) you walk on. -15 % of the tires you ride on, -30% of the fiberglass filaments in circuit boards, bathtubs, boats, doors, and more, -25% of many housepaints, adhesives, grouts, caulks, and putty -30% of sparkplugs, power insulators, dinnerware. and toilets, -50% of most catalysts (both cracking and emission control) -20% of cosmetic powders. -20% of wire insulation, and animal feed to rocket insulation!

Jan 1, 1993

By Floyd C. Bossard

In underground mining operations, the over- riding issue has to be protection of worker health and safety. The employees underground, making a living in a dangerous occupation, know these are major issues. These men bargain their lives and health on the presumption that the operating management knows its business, and they, the underground employees, can pursue their occupation with the assurance that management has provided a safe and healthy ambient underground environment. When management assumes the mantle of protection of underground workers, it has to be positive that qualified engineers have designed the project, and that capable operating personnel are in charge and always available. Those persons with these responsibilities must be knowledgeable in the engineering and occupational health aspects of sine ventilation. The ultimate function of a mine ventilation system is to provide a comfortable, healthy and safe ambient environment for the underground workers. The attainment of these objectives has been complicated with the increased application of electrical equipment and diesel-powered mechanized mining equipment underground (discharging toxic diesel emissions); increased production rates with the attendant increased production of airborne dust; and mine development in increasingly hostile mineral formations containing combustible strata gases, radon gas emissions, along with high heat and humidity. In general, the modern mechanization of present mining operations has resulted in a sore complex set of problems for the engineer planning the underground ambient environment.

Jan 1, 1983

By W. G. Willson, D. E. Walsh, B. Irwin

Low-rank coal (LRC) drying processes are generally categorized by operating temperature, drying environment and type of feed (either sized or ground coal). Within these broad categories, drying processes differ according to the type of drying equipment and methods of quenching and stabilizing the dried products. This paper focuses on the produce quality of various LRC drying processes including conventional low and high temperature evaporative drying and non-evaporative, hydrothermal drying. The former may be preferred if the dried product can be utilized immediately, but moisture reabsorption, spontaneous heating and fines production during handling are problems associated with longer term storage, transportation and utilization. Methods for reducing these problems are discussed. Hydrothermal processing is an advanced technology featuring high pressure, non-evaporative drying, which solves stability problems by producing a liquid feel.

Feb 24, 1997

By P. J. Cook

Comminution is one of the fundamentals of mineral processing, requiring large expenditures to be made on capital equipment, installation, power and maintenance. The trend toward lower grades and higher operating costs, mean mining operations are becoming increasingly marginal. The challenge is to improve and more importantly, utilize crushing and milling technologies that provide for reduced capital and operating costs whilst providing increased unit efficiencies. The Svedala Barmac Autogenous Crushing Mill presents such an opportunity by providing many of the cost savings and production increases required by its ability to produce a finer mill feed size and realize reduced energy consumption. This paper briefly describes the operation of the Svedala Barmac Autogenous Crushing Mill and reviews its benefits towards improving the efficiency of crushing and milling operations.

Jan 1, 1999

By T. C. Eisele

The use of column flotation was considered for the ?reverse flotation? of iron ore, where the gangue (quartz) was recovered in the froth product. This use of the froth for carrying the gangue mineral rather than carrying the valuable concentrate significantly changes the operational requirements of the column. The objective of this work was to determine which of several column flotation technologies would be most suitable for this type of flotation operation. Studies were carried out using both the Jameson column and the Deister column. Comparative results are presented that show the capabilities of both column types in this application relative to conventional Wemco flotation cells. Columns were demonstrated to have grade-recovery performance superior to what could be achieved with conventional cells. Two-stage flotation with the columns could produce a concentrate that was up to 70.2% Fe at 87.5% iron recovery, compared to 70.4% Fe at only 77.7% iron recovery for four stages of flotation in conventional cells. It was shown to be particularly important to operate the columns to recover a maximum of the quartz gangue into the froth. It was noted that there are often problems in scale-up of laboratory columns to plant scale, because the increase in height and the decrease in the ratio of height to diameter at the larger scale allows more axial mixing and bubble coalescence, both of which degrade the column performance. Horizontal baffling was shown to improve column performance by reducing axial mixing and breaking up large bubbles, and so the use of such baffles in the reverse flotation application was investigated.

Jan 1, 2007

By Michael S. Zhdanov

One of the major problems of mineral exploration is the ability to reliably distinguish between uneconomic mineral deposits and economic mineralization. While the mining industry uses many geophysical methods to locate the mineral deposits, until recently, there was no reliable technology for mineral resources identification and characterization. The main goal of this project is to develop a new geophysical technique for subsurface material characterization, mineral exploration and mineral discrimination, based on electromagnetic methods. The proposed new technique is based on examining the spectral induced polarization effects in electromagnetic data using the modern distributed acquisition systems and advanced methods of 3-D modeling and inversion. The recovered parameters of the relaxation model will be used for the discrimination of different rocks, and in this way will provide an ability to distinguish between uneconomic mineral deposits and zones of economic mineralization using geophysical remote sensing technology (Zonge, 1976). The proposed research and development is undertaken using multi-partner collaboration between the University of Utah, four major mining companies, Kennecott Exploration, BHP Billiton World Exploration Inc., Placer Dome Inc., Phelps Dodge Exploration, and Zonge Engineering Inc., which is equipment manufacturer and service provider to the mining industry. The multi-partner collaboration between the academic institution, the University of Utah, and mining industry helps to identify the appropriate mining target and conduct the field experiment for practical demonstration of the developed new technology, which is an important part of the this project.

Jan 1, 2005

By F. G. Heivilin

There will be 3 billion people moving into cities by 2050. Permitting is both the biggest obstacle and the biggest opportunity for mining. The problem is not if we have the right minerals, but how we can permit and produce it in a ?Sustainable? manner. A ?Permit? and a ?Sustainable Development Plan? may soon be the same thing. How do we produce the minerals we need with: 1. The lowest possible carbon footprint. 2. Social license from community outreach by being a catalyst and not a problem in a ?Green World.? 3. Enhanced water supply during all stages of production. 4. Meeting requirements of our customers for service, quality, & cost. How important is it to have a complete ?Sustainable Development Program?? First, no plan is complete!!! It is a work in progress subject to continuous improvement. We need to work together to get the results we want. The goal of the world communities is to become carbon neutral by 2050. What is the mining community?s goal? Do we have one???? When a Clorox, Colgate Palmolive, Wal-Mart, Toyota, or Caterpillar buys a product, what are your chances of getting an order without a good program in place? The answer is it will be difficult or impossible shortly and you will be requiring the same thing with your suppliers. This is an opportunity if you are in the lead and it soon will be a necessity for most mining and processing companies requiring much extra effort to catch up. For some mines it was a necessity to get most of the SD plan to get permitted. The number of companies in the extractive industries with a full Sustainable Development Programs is expanding rapidly as shareholder demands for transparency continue to grow.

Feb 27, 2013

The failure of a seal in an underground coal mine can have devastating consequences. Traditionally seals have been constructed as flat walls. Large hydraulic dams, on the other hand, are constructed as concave arches. This paper presents an initial analysis of the potential strengthening of seals by concave construction as well as the impact of additional cost in terms of labor and material. A simple finite element analysis of three-dimensional solids under uniform loading allows comparisons between the strength of a flat wall and a curved arch. The models are examined for reasonable behavior and displacements at 20, 50, 100, and 200 psi loads.

Jan 1, 2007

As ore deposits become finer grained the requirements for regrinding before cleaning or leaching have increased substantially. Despite this increasing need, there is no standard test to predict grinding energy requirement below 70 microns. The standard Bond Mill test applies for coarser ball milling, but is not appropriate for stirred milling with fine media grinding to 70 microns. With no industry -standard test, the energy requirement is often made on the basis of supplier estimates or benchmarking against similar applications. Yet suppliers use vastly different scale-up methods which result in widely different energy estimates. Estimates can differ by 100-300% even for similar mills. This must result in serious errors to install either too much or too little grinding power. This paper explores this by comparing the actual performance of full scale regrind mills against their original design estimate. It confirms that serious scale-up errors have been made, and have then been perpetuated by ?benchmarking?. The test conditions to achieve accurate power estimation are discussed. The essential test conditions are: continuous (not batch) tests, ensure steady state (no coarse fraction retained in test mill), correctly account for classification, measure energy directly (not inferred), and using the same media size as the full scale installation. Failure to correctly address even one of these factors can bias results by 40%; failure to address several multiplies the error.

Jan 1, 2011

By E. Siami-Irdemoosa, S. R. Dindarloo

Ease of excavation or rippability, also called diggability or excavatibility, is a critical decision-making parameter in the selection of both the overburden removal method and the required equipment in surface mining and geotechnical engineering projects. The most widely used method of estimating rippability is rock mass classification. Although there are different classification schemes in the literature, all of them have the two major limitations of sharp transitions at class boundaries and subjective uncertainties in decision making. In this study, the decision trees method was employed as a classification tool for estimating ground rippability, using the four rock mass parameters of weathering degree, uniaxial compressive strength, joint spacing and bedding spacing. The results were compared with those of the widely used method of diggability index rating (DIR) and a fuzzy-based DIR. The problem of subjective uncertainty was resolved in the proposed decision trees method, as the tree rules were derived automatically from the training data sets. Compared with fuzzy-DIR, a decision tree classifier is simpler, needs less computational time and is more appreciable by industry practitioners. Nevertheless, the proposed method is not flawless and, similar to both the conventional and fuzzy DIR methods, yielded poor estimations in particular instances. The limitations of the three methods are discussed.

Jan 1, 2015

By J. Donovan Jacobs

Many improvements in the art of underground excavation have appeared during the past two decades. These improvements have been both in methods and in machinery and have resulted in more economical construction of today's tunnels. In the realm of machines, the developments of continuous boring heads for either soft ground or rock, random arm excavators and the sliding tunnel floor (Magic Carpet) have each made contributions toward more rapid tunneling. CONTINUITY OF ADVANCE Tunnel boring machines are often referred to as "continuous excavators". Continuous advance (without cyclical interruptions) has not been achieved, however, in any of the machines now in use. In most rotary-head tunnelers the thrust needed to make the cutters bite into the face is obtained from hydraulic cylinders reacting against anchoring devices held stationary by pads which grip against the sides of the tunnel. With this system the forward motion of the cutting head is continuous only until the propelling cylinders have reached their limit of extension. At this point the grippers must be released, moved forward and reset before a new cycle of advance can be begun. Some machines are built to obtain their propelling thrust from hydraulic cylinders pushing backward against newly-installed rings of tunnel support. This is the customary method for propulsion of shields. With it, each cyclical advance or "shove" must await the erection of a new ring of supports. Faster tunnel driving

Jan 1, 1974