Search Documents

By Scott Rosenthal, Dave Gilkey, Theresa Stack, Daniel Autenrieth, Ciara Kremer

Jackleg drill operators are exposed to harmful levels of hand-arm vibration (HAV). Anti-vibration handles and gloves provide modest reductions in HAV exposures and forearm muscle exertion from the use of anti-vibration handles and gloves by jackleg drill operators. The goal of this pilot study was to investigate changes in HAV with the use of anti-vibration gloves and handles compared to forearm muscle exertion experienced by operators and measured with surface electromyography (EMG). Five subjects operated the drill under four different cases: no anti-vibration controls, anti-vibration gloves only, anti-vibration handle only, and simultaneous anti-vibration handle and glove use. Muscle exertion was expressed as a percent of maximum voluntary contraction (%MVC) and was compared using Welch’s ANOVA with Games-Howell post hoc comparisons. The case with both anti-vibration controls in use simultaneously (largest grip diameter) was associated with a mean %MVC of 36.13% during operation for all forearm muscles combined, which was significantly higher than that of the other cases (p < 0.05). There were no statistically significant differences in mean HAV exposures. The anti-vibration handle with anti-vibration glove case only increased the maximum allowable exposure time by 8 min as compared to the control case without any anti-vibration controls. These results suggest that the modest HAV exposure reductions from the use of anti-vibration handles and gloves may pale in comparison to the increased muscle exertion resulting from their use, and this trade-off among jackleg drill operators is a potential concern that warrants further investigation.

Jul 12, 2021

Coal bursts are one of the least understood yet the most critical hazards in underground coal mines. The ground motions induced by seismic events can trigger unstable failure of coal and rock mass and degrade the surroundings of an excavation. Therefore, the characteristics of ground motions should be fully investigated for an improved burst risk management. This paper analyzes ground motion features of a longwall panel from a typical underground burst-prone coal mine in China. The results showed that most of the ground motions on roadways were hardly initiate coal bursts due to insignificant energy input to the damage. The intensity of ground motions in near-field zone were nearly 20 times higher than those in far-field zone. The strongest vibration on roadway was induced by a coal burst with energy of 28,600 kJ, which can cause ground motion of 0.77 m/s and equivalent dynamic stress of 14.69 MPa. The findings of this paper can improve the assessment of seismic risks and its management.

Jan 7, 2020

By Thomas Schwind, Pamela S. Moran

For short tunnels, a reinforced cast-in-place lining is not economical and shotcreteis a logical substitution. In the past, reinforced shotcrete linings have been constructed with lattice girders and welded wire fabric. For the Russia Wharf Tunnel in Boston, MA, the Contractor, with the help of the Dr. G. Sauer Corporation offered the MBTA a VECP to substitute the reinforced cast-in-place concrete lining with a steel fiber reinforced shotcrete lining. The challenge was to adequately model the ductility of the steel fiber reinforced shotcrete and to test the shotcrete prior to and during construction to assure quality control. To our knowledge, this type of numerical simulation has not been used on any other tunnels in the US.

Jan 1, 2005

By M. S. Klima, A. Simard, M. L. Turek

Laboratory testing was carried out to evaluate several devices for recovering clean coal from bituminous coal refuse material. The bulk of the testing focused on using a dense-medium cyclone to process -0.6-mm refuse material. A hindered-settling column and a spiral concentrator were also used to process 1.2x0.15-mm material. Product yields and ash contents were obtained for all tests, while partition curves were generated for selected tests from which the characteristic performance parameters (relative density of separation and probable error) were determined. The results indicated that the dense-medium cyclone was capable of cleaning down to 0.037 mm, while the other devices were effective to 0.15 mm.

Jan 1, 2002

By Steve Kral

Globalization was the key word for the mining industry during the 1990s, just as productivity was the key word of the 1980s. And globalization will remain the key word as the industry enters the 21st century, according to speakers at the Colorado MPD Meeting held in Colorado Springs, CO in May. The meeting, put on by the Colorado Section SME Minerals Processing Division, drew about 120 people to the Broadmoor Hotel. “Operating Globally” was the theme of the 49th annual conference. Speakers addressed the reasons why mining companies have limited their spending in the United States and have moved into Third World and developing nations.

Jan 1, 1999

"Lax, misguided, and dangerous" is Rep. James Santini&apos;s description of the official US position on strategic nonfuel minerals. Santini (D-NV), chairman of the House Mines and Mining Subcommittee, criticized the Interior Department for "its long record of benign neglect" regarding the domestic minerals crisis. Santini made his remarks at a news conference at the American Mining Congress convention in San Francisco, where he released his subcommittee report "US Minerals Vulnerability: National Policy Implications." The report-said to be the first major congressional study of the minerals issue by a committee of jurisdiction is the result of a two-year inquiry. The investigation was undertaken, according to the chairman, "because no person or agency in the executive branch of government fully grasps the critical importance of nonfuel minerals to the nation&apos;s economy, defense, and quality of life." The report also urges a larger role for the Department of Defense, which has "stood passively by for many years as a consuming by-stander," according to the report. President Carter&apos;s incomplete Non-fuel Minerals Policy Review also drew the committee&apos;s ire; Santini calls it "a tragic waste that cost tax-payers $3.5 million and the loss of some 13,000 person-days." The subcommittee examined the following issues for its report: • The US minerals industry&apos;s inability to meet national raw material needs under a "hodgepodge of contradictory, restrictive, and irrational" federal regulations; • Dependency on foreign sources of strategic minerals in times of "increasing resource nationalism" and "Soviet mineral expansionism;" • National security needs for foreign mineral resources that do not have effective substitutes; • The US government&apos;s approach to national minerals policy "amid a growing realization that such a policy does not exist." The subcommittee report includes an analysis of public and private studies on nonfuel minerals and discusses a series of policy problem areas that negatively affect domestic production. Capital formation disincentives, tax policies, antitrust enforcement, environmental laws, health and safety regulations, technical problems, and restricted access to federally-controlled public lands contribute to what Santini calls a "tragic irony." "The irony is that we are a nation vastly rich in mineral resources yet our own government chooses to stifle development of these critical raw materials and thereby increase offshore reliance. The tragedy is that we also are ensuring US vulnerability to severe economic dislocations and a weakening of our national security." In just six years, from 1973-1978, the US trade deficit in nonfuel minerals rose from $2 billion per year to $8 billion, according to the report. The country imports more than 50% of 23 critical minerals, including 100% of its manganese, chromium, cobalt and platinum. The US is promoting its dependence on foreign mineral sources at the very time the security of many of those sources is becoming less certain, the report notes. Santini said the subcommittee investigation revealed a vulnerability that may be more serious and pervasive than that of foreign oil. The US may be able to develop alternate energy resources, but there are no effective substitutes for many nonfuel minerals. The report also discloses that US stockpiles of critical and strategic minerals are of inadequate supply and quality. Holdings of some vital minerals are far below present objectives, and for some there are no holdings at all, according to Santini. To resolve the current crisis, the report makes the following recommendations: • Complete immediately President Carter&apos;s Interagency Nonfuel Minerals Policy Review; • Implement (throught the Interior Department) the 1970 Mining and Minerals Policy Act; • Create an Office of Energy and Minerals with the same stature, power, and oversight responsibilities as the Council on Environmental Quality; • Ease federal restrictions on mineral exploration and development on public lands and implement a complete review of public land use policies; •Fund for and fulfill US nonfuel minerals stockpiling objectives; •Increase federal funding for non-

Jan 11, 1980

In this paper, a mixed integer linear programming (MILP) model for the short-term scheduling of open pit mines is formulated. The proposed model aims at sequencing the blocks extraction over multiple short-term periods. The model takes into account multiple processes, waste dumps, and multiple stockpiles. The short-term scheduler makes a decision on the period, destination, and route that ore and waste are supposed to take to minimize costs while meeting all the mining and processing constraints. The destinations of the extracted materials are also controlled by their rock types. A monthly short-term production scheduling case study of an iron ore deposit is carried out over a year to validate the model.

Jan 1, 2011

By Harold J. Schock

The cases of no auxiliary ventilation and ventilation with tubing were mathematically modeled, using a turbulent dispersion model. The scooptram that is used to load is modeled as a variable-speed, variable-strength source of pollutants moving in and out of the dead-ended drift. Model predictions are compared to experimental measurements. A parametric analysis was performed to determine the effect of exhaust pipe location and time spent out of the drift, as well as to determine if a relationship existed between CO2 and NO levels. It was concluded from this analysis that when modeling a load-haul-dump cycle, it is necessary to use a model that has the capability of predicting changes in source strength as well as source location. It was also determined that four relevant factors include effective heading height, apparent longitudinal diffusion coefficient, transverse concentration gradient at the face, and average dispersion width of the exhaust jet. As these factors change with heading geometry and ventilation configuration, they were determined experimentally, Carbon dioxide was used as a tracer to calibrate the model; since, knowing the fuel flow rate, it is possible to calculate CO2 production. The above four factors in the computer model were calculated using a regression analysis, comparing predicted local concentrations to measured local concentrations. The model was then verified after this calibration process using additional experimental results. With the calibrated model, it is possible to predict pollutant concentrations at any location in the heading using an engine map and the previously calculated flow field. A parametric analysis shows that the exhaust pipe location can have a significant impact on operator exposure to exhaust gases. It was also shown that NO concentration varies directly with C02 levels. Predictions using the dynamic model are contrasted with constant source strength (pollutant flow rate) results. An analysis of these predictions for computing time-weighted average NO shows the dynamic model predictions of operator exposure to this pollutant to be less than one-half of the value predicted using a constant source model.

Jan 1, 1981

By J. D. Patsey, G. T. Lineberry

Introduction A computer program was developed for analyzing drum-type hoists before modifying an existing system or designing a new one. Its use permits the preliminary evaluation of a system before seeking technical assistance from mine hoist designers and manufacturers. The user-friendly program accepts a variety of data and analyzes hoisting systems for any balance state. The program can be used to calculate skip capacity to yield a desired production rate, solve for drum face width, select a permissible wire rope, estimate total horsepower of the hoist plant, and estimate annual power cost. Whether required for a large mining complex or for a relatively small operation, a hoisting system must be carefully designed to ensure the efficient, reliable, and safe flow of material. Because shaft sinking and hoist installation can total between 2.5% and 3% of the cost of opening a deep mine, proper hoist selection is critical. Today&apos;s mining engineer has at his disposal the most powerful design and analytical aid ever, the microcomputer. There is, unfortunately, limited software for the study of hoisting systems, unlike that for other materials handling equipment (Manula and Albert, 1980; Prelaz et al., 1964; Bucklen, 1969; Thompson, 1985). HOIST reduces a time-consuming set of calculations to a concise package of interrelated subprograms. A literature review revealed no common-user programs to analyze hoisting systems, although at least four major hoist designers/manufacturers/installers have their own in-house programs. To provide a tool with which the mining engineer could preliminarily analyze a materials hoisting system or could check the calculations of a hoist contractor, a computer program was developed. HOIST was written in BASIC for the IBM-PC for ease of program adaptation and to encourage field use on compatible systems. Details of program development are omitted, since the basic principles of hoisting analyses are relatively straightforward, simple, and readily accepted (Harmon, 1973; Nordberg, n.d.; Adler, 1957). Program features, intended usage, and benefits of the computerized solution are emphasized over theory development and mathematical rigor. Background The mine hoist system that is selected and installed at a mine is the "lifeline" of that mine, with installations lasting 20 years or more. Thorough study is warranted to ensure that productivity demands are met at a minimum cost per ton. The increased cost of a large, powerful, high-speed hoist must be offset by increased production to justify its selection. To optimize this tradeoff, an extensive hoisting analysis should be performed. The analyses to properly size the skip (or cage), the drum, and the hoist drive are conducive to computerization, permitting rapid evaluation of changeable operating and design parameters, such as velocity, acceleration, state of balance, and productivity demand. The program is particularly useful in conducting sensitivity trials, such as investigation into the effect of change of productivity on skip capacity and on horsepower of the hoist drive. HOIST is currently limited to the study of drum-type hoists with cylindrical drum(s). However, only minor changes to the program would permit analysis of friction hoists and conical drum configurations. Model development and testing The program is based on accepted equations and physical relationships. Examples of manual calculations formed the basis for decision points and program branching. Data is input in the order that it would be needed if the problems were solved manually. The choices are arranged likewise. HOIST was developed in sections, with manual solutions performed to check program logic. The testing became more rigorous as sections were completed. Output from one section becomes input for following sections, as appropriate. The simplified flow diagram of HOIST is given in Fig. 1.

Jan 2, 1987

By Nikhil Dhawan, Amit Barnwal

The present study reports a processing route to recover metals from integrated circuits of discarded random access memory (RAM) units containing ~ 66% printed circuit boards and ~ 33% integrated circuits. The integrated circuits are manually separated, grounded, classified, and subjected to water fluidization for the effective separation of metals. The significant separation was achieved via water fluidization, and the underflow fraction was magnetically separated. The magnetic fraction was thermally exposed in a muffle furnace, and the process optimization was carried out using a Box-Behnken statistical design. The detailed characterization at subsequent steps significantly aids the understanding of metal-plastic separation and enrichment. A concentrate containing 97% metals (Fe-59%, Ni-9.5%, Cu-7.7%, Sn-13.4%, Pb-5.6%, Ag-1.6%) with 96 wt% recovery can be recovered from discarded IC units. The process pursued is simple, adaptable, and environment-friendly, and the product can be used in conventional smelters.

Jun 23, 2020

By Michael V. Mergentime, Prakash M. Donde

The Nutley Quarry Trunk Sewer Project is a good example of a tunnel that went through difficult and complex ground. The 2 m (7ft.) diameter and 840 m (2,750 ft.)long tunnel passed through soft ground, mixed face, and hard sandstone. The soft ground and mixed face tunneling provided several challenges. During excavation of the tunnel, the Contractor encountered a number of unanticipated large boulders. In addition, the length of the mixed face portion of the tunnel increased by 100%. The Contractor tried various construction techniques to overcome the difficult ground conditions and complete the project. The tunneling progress was slower than expected. The Contractor claimed extra costs for differing site conditions. Through discussions and negotiations between the Contractor, Engineer, and Owner, all of the changed condition claims were settled before the construction of the project was completed. This paper addresses the difficult ground conditions, claims evaluation, and how they were resolved by cooperative efforts between the Contractor and the Owner/Engineer.

Jan 1, 2001

By Feridon Ghadimi, Saeed Mojeddifar, Massume Khavari

Separation of geochemical anomalies from background is an important and essential issue in the exploration of mineral deposits. Statistical methods are used to separation of anomaly from background. Fractal/multifractal and singularity methods are very suitable for the separation of weak anomalies. For interpolation, various methods could be used such as most distance-weighting methods, kriging, spline interpolation, interpolating polynomials, and finite difference methods. This paper addressed application of multifractal techniques together with finite difference procedure to detect the anomalous regions. Fractal models such as concentration–area, spectrum–area, and singularity index model were selected to identify Pb–Zn anomalies. In this research, 170 samples from 33 boreholes were taken in the Haft-Savaran area and analyzed for determination of Pb–Zn anomaly. Singularity method was a suitable method for separating Pb and Zn anomalies. Also, the results showed that the geochemical anomaly has occurred along NE–SW trend and is consistent with the sulfide mineralization process and the faults of the region.

May 18, 2020

By R-H Yoon

The MicrocelTM column flotation technology has been developed based on the fundamental understanding that the first-order flotation rate constant increases approximately as the inverse cube of bubble size. In this technology, bubbles in the range of 100-400 pm are generated by pumping aerated slurry through an in-line static mixer. The high-shear agitation provided by the in-line mixer produces small air bubbles without requiring large frother additions. This column has been tested successfully for processing a variety of non-metallic minerals including kaolin clay, graphite, phosphate, and feldspar.

Jan 1, 1993

By Christian F. Baiz

The author will present a discussion of the steps which must be taken by the prospective developer of a small mining operation to establish technical credibility when seeking financial backing. Particular emphasis will be given to the differing levels of technical work (and their relative cost) which must be accomplished to supply the information necessary to satisfy potential investor groups, whether they be other mining companies, equity investors, or financial institutions such as venture capital firms or commercial banks.

Jan 1, 1981

By S. Janisko

Studies have linked long-term inhalation of diesel exhaust with adverse health effects such as cardiovascular disease, cardiopulmonary disease, and lung cancer. Diesel exhaust levels in underground mines can approach 100 times the environmental level and are therefore monitored closely in the mining industry. Elemental carbon (EC) (a product of diesel combustion commonly referred to as ?soot?) has proven to be a good indicator of diesel exhaust levels. The current procedure for measuring EC levels involves taking personal samples from a mine worker?s breathing zone and/or stationary samples in various parts of the mine and subsequently sending these samples to a lab for analysis by NIOSH 5040 method. Unfortunately, the whole process can take up to several weeks to complete. To address the problem of waiting weeks for results, NIOSH?s Pittsburgh Research Laboratory is developing a portable device for measuring levels of elemental carbon. This optical device takes a continuous sample of air in the surrounding environment and measures the absorbance of light passing through a filter that collects diesel exhaust particulates within the instrument. This technology can provide a near real time measurement of EC with accuracy within 10% error. The ability to take near real time measurements, combined with the instrument?s portability (currently small enough to be worn on a miner?s belt), makes this device extremely useful in the mining industry.

Jan 1, 2009

By John Berney-Ficklin

Large scale grinding mills can reduce both capital and operating costs for concentrators. These mills can be effectively used, but they must be free from design and manufacturing deficiencies if they are to reach their full potential and avoid costly downtime. This paper presents the evolution of today&apos;s complex grinding mill specifications and discusses the most important items to look for when buying new equipment. It emphasizes the need to monitor specification requirements during design and manufacture. It also discusses the growing trend to have grinding mills fabricated in overseas plants, and the importance of recognizing this when preparing specifications.

Jan 1, 1987

By Ingo Ossenbühl, Wolfgang Dolsak, Vojtech Gall, Axel G. Nitschke

"Yielding support systems for application in underground construction have a long history, primarily in mining. Typical examples are tunnels subject to loading conditions that lead to overstressing of the newly installed support or existing tunnel structures in active fault zones. Recent applications for tunnel rehabilitation projects unveiled the capabilities and flexibility of combined yielding support systems presented in this paper. Frequently, the main requirements for tunnel rehabilitation applications are a fast, safe, and simple installation along with the need for flexibility with regards to existing tunnel geometries. A combined support system consisting of steel sets with yielding connections and special groutable hoses has proven to be an efficient support measure providing a multitude of advantages compared to conventional rehabilitation approaches. The presented yielding support system provides an immediate and active support, while it allows for controlled yielding upon experiencing loads beyond its support capacity. INTRODUCTION The excavation of underground spaces leads to redistribution in the existing stress regime. This load redistribution goes along with deformations in the surrounding rock mass. Magnitude and duration of these deformations depend on the tunnel’s depth and geological conditions, but also on the installed support system. Modern civil tunneling infrastructure has generally an envisioned service life of about 120 years. Conventional tunneling provides typically a dual support system, split into the initial (or primary) and final (or secondary) lining. A typical design principle in civil tunneling is to let the vast majority of deformations acting on the initial lining cease, before the final lining is installed. Based on this approach, the loading on the final lining is significantly reduced and signs of overstressing, such as cracking of the lining, are typically limited to the initial lining. However, special cases in swelling and squeezing ground require different approaches, including yielding support systems."

Jan 1, 2016

By T. L. Owen

Since 1993 Cyprus Amax has brought $2.5 billion dollars of greenfield and expansion projects into production, taking it from a mid-sized domestic minerals company into a major international minerals organization. The near simultaneous development of these multiple mineral projects in different locations around the world provided the opportunity for Cyprus Amax to develop a formal project management approach based, in large part, on an outsourcing philosophy. This formal project management system along with its outsourcing philosophy has served the growth agenda of Cyprus Amax extremely well. These preceding factors, coupled with the in-house retention of a core project group that fully understands the breadth of skills and abilities needed to undertake development of multiple large projects successfully, have been the cornerstone of Cyprus Amax’s project development success.

Jan 1, 2000

By J. Pascoe, J. H. van Laar, J. H. Marais, F. J. L. Matthee

Advanced measurement and verification (M&V) is a process where the impact of an energy initiative is determined in real time. Data prediction models can be used to predict and compare energy consumption with a predetermined baseline. Deeplevel mines can benefit from advanced M&V as the impact of operational changes can be identified in real time. Ultimately, this can ensure that informed decisions are made regarding energy management based on the impact and severity of the occurrence. Previous studies on advanced M&V do not account for operational changes to the model’s baseline. These changes can significantly impact the performance of both the mine and related activities. The aim of this study is to propose a method that can accurately predict the energy consumption of a deep-level mine regardless of operational changes. To achieve this objective, nine different data predictive modelling techniques were considered. The proposed method is based on the Moving Average (MA) modelling technique due to its simplicity, flexibility, and rapid development time. The coefficient of variation for the root mean square error (CV(RMSE)) was used to statistically analyse the modelling error. If the predictions exhibit an unsatisfactory CV(RMSE), the model dynamically adjusts to reduce the prediction error. The model was developed to adapt to operational changes in scenarios where the standard model becomes irrelevant. The method developed in this study was able to predict the future energy consumption of deep-level mines with an accuracy of 99%, improving the mine’s energy and finance management.

Dec 13, 2023

Effective tools are not only essential for the design of practical and efficient underground mine ventilation systems but must also play an integral part in the operation of the mine. One such tool is VUMA-coal ventilation simulation software. VUMA-coal is Windows-based and has been specially designed for the simulation of underground coal mines and includes user-friendly coal specific interfaces and three-dimensional graphics designed to facilitate in the construction and analysis of networks. VUMA-coal can be utilised during the design phase of new collieries, be used to conduct ?what-if? and optimisation studies, and be integrated into the ?day-to-day? ventilation related operations. In addition, VUMA-coal can be used to simulate dust and gas distribution in a ventilation network, as well as predict the impact of control measures. This paper describes the interactive VUMA-coal ventilation simulation software and its underlying design features and outlines a case study of how VUMA-coal has been integrated into Anglo Coal?s Ventilation and Occupational Hygiene Engineering [VOHE] department as part of the standard planning and evaluation process in their operational mines as well as long term planning and future mining operations.

Jan 1, 2009