Search Documents

By T. Ruff, J. Steele

The lack of visibility near earthmoving equipment results in an average of five fatalities in U.S. surface mines each year. These accidents occur when a piece of equipment either strikes another vehicle or worker, or travels over the edge of an embankment. Researchers at the National Institute for Occupational Safety and Health have evaluated off-the-shelf proximity warning systems that sense obstacles near the equipment and provide an alarm to the operator. Limitations of existing systems have necessitated the development of new systems designed specifically for mining equipment, including a GPS-based proximity warning system and a computer-assisted stereovision system.

Jan 1, 2004

By Michael E. Allen

The building of sanitary and storm drainage sewers in urban or environmentally sensitive areas often requires the use of tunnel construction procedures. While hydraulic considerations may require only small diameters, traditional tunneling techniques make small sizes the least economical. Current state-of-the-art techniques using highly mechanized systems of pipe jacking can provide cost effective solutions to the problems of construction of small size tunnels. The characteristics of mechanized pipe jacking allow rapid advances under difficult ground conditions. The basic pipe jacking cycle is used with a variety of excavation systems to permit the contractor to satisfy engineering as well as economic parameters. These characteristics and several of the systems available are outlined.

Jan 1, 1981

By S. Chander

Neutralization of acidity by addition of alkaline materials is a commonly used method to treat acid mine drainage. However, this procedure requires large amounts of reagents based on acid-base accounting. The potential use of organic additives in preventing or ameliorating acid mine drainage was investigated in this research. The tests were conducted in weathering columns using refuse samples from a coal cleaning plant. Both cationic and anionic compounds were tested. For a comparison, tests were made in the presence of limestone and lime. The results show that some of the reagents substantially retarded the rate of oxidation whereas others even enhanced it. The suppression of the rate of pyrite oxidation was ascribed to surface chelation. Formation of surface compounds prevented the pyrite particles from further oxidation. Such a treatment required only small quantities of reagents since the reaction was confined to the surface.

Jan 1, 1992

By Charles Schmidt

Phalabonva (Figure 1) is situated in the northern province of South Africa adjacent to Kruger National Park, about 500 km from Johannesburg. The nearest South African port to Phalaborwa is Richards Bay about 700 km distant by rail.

Jan 1, 1999

By Clifford O. Hamilton

In both mature and young maintenance workforces, the workforce commonly lacks some of the skills required for their assigned work. We call this the "skills gap." This skills gap usually exists in a new operation because although you may hire qualified maintenance personnel, they more often than not have little if any experience with the specific equipment at the facility. Performance Associates International, Inc., has developed and proven a technique to address the maintenance skills gap that is usually found in a new operation.

Jan 1, 2001

By R. Mohr

Storm water runoff from mine facilities such as haul roads, waste disposal sites and ore bodies have become recognized as the primary facilities associated with non-point source drainage. Depending on the ore body, facility design and geographical setting, nonpoint source drainage can cause pollution impacts to local surface and ground water resources. Non-point source impacts from surface mine drainage have become an important regulatory issue for the mining industry. Implementing non-point source drainage control plans that prevent impacts to water resources can be accomplished cost-effectively with moderate labor requirements. Design considerations for plan development must incorporate parameters including contributing drainage area size, slope, flow velocity, vegetation characteristics and soil scour velocities. The success of non-point source drainage and erosion stabilization planning is based on implementing control measures that dissect drainage patterns, reduce flow velocities and disperse runoff towards sediment control sites. Interim and long-range drainage control measures should begin during exploration activities. Regulatory legislation addressing non-point source pollution sources was enacted as amendments to the Clean Water Act (CWA) in February 1987. The legislation required states to initiate non-point source pollution control programs.

Jan 1, 1991

By J. D. Lowell

The gold content of prophyry copper deposits ranges from less than .05 gmt (ppm) to more than 1.0 got, and most deposits contain on the order of 0.05 gmt Au. Perhaps the highest grade mineralization which has been found in close proximity to a porphyry copper is the Ok Tedi Gold Cap orebody whose grade falls in the 2-3 gmt Au range.

Jan 1, 1988

By P. Sanchez-Mejorada

Quimica del Rey, SA, a subsidiary of Industrias Peñoles, SA de CV, produces sodium sulfate from brines extracted from a playa of Laguna del Rey, located in the State of Coahuila in northern Mexico. The spent brine is used as raw material for the production of magnesium oxide. The brine, which contains ions of sodium, magnesium, sulfate, and chlorine, occurs filling intercrystalline voids of a lenticular evaporite deposit whose main constituents are glauberite (sodium-calcium sulfate) and blöedite (sodium-magnesium sulfate).

Jan 1, 1987

By O. A. Paulson, D. D. Runnells, D. P. Dupon, K. J. Bruxvoort

Background groundwater quality is often used to drive remediation programs at sites with waters that have been affected by mining activities. In the past, these levels were sometimes chosen without rigorous statistical and geochemical analysis. A probability-distribution approach was used at the Sweetwater Uranium Project to separate a large set of geochemical data into populations that represent contribu¬tions from different sources. Natural background populations were identified for major ions, metals and radionuclides, and these were submitted to the US Nuclear Regulatory Commis¬sion (NRC) to modify the extent of a corrective-action pro¬gram and to establish control limits for future monitoring.

Jan 1, 2000

The bromine review did not arrive in time for publication in the June issue. Bromine production in the United States during 1992 amounted to 171 kt (376 million lbs), a 453-t (I-million lb) increase from 1991. Data compiled by the US Bureau of Mines indicates this increase was due mainly to greater exports of elemental bromine and bromine derivatives (flame retardants). Exports increased despite the economic slowdown in Europe and Japan. The United States remains the world's largest bromine producer, with about 42% of the total. Israel is ranked second, followed by the United Kingdom, the former Soviet Union and Japan.

Jan 1, 1993

By D. Ince

Flotation of dolomite from apatite was investigated, using dodecylamine hydrochloride or sodium oleate as the collector, with and without inorganic modifiers such as sodium chloride. Separation of dolomite from apatite was anticipated from the single mineral experiments under various pH and collector concentration conditions. Flotation selectivity in the mixtures, however, was found to be limited. Attempts to control the flotation response of these minerals by addition of salts such as NaCl and KCI indicated that selectivity is possible. The presence of sodium chloride was determined to depress apatite flotation using sodium oleate, leaving dolomite flotation unaffected (Moudgil and Ince, 1989). In this paper, conditions for optimum separation and the effect of major parameters on the desired selectivity are discussed.

Jan 1, 1992

By Diane Germain, Normand Tassé, Claude Dufour

At the East Sullivan site, pore-waters underlying a wood waste cover that prevents sulfide oxidation are characterized by an anoxic environment, abundance of dissolved organic substrates, and near neutral pHs. Such conditions favor sulfate reduction and base metals precipitation as sulfides, as well as carbonate-metal precipitation. Pore-water composition from 1992 to 1998 shows a significant Fe2+ decrease. Therefore, the restoration strategy of that site capitalizes on these alkaline and reductive properties. Since 1998, a novel treatment of acid effluents, based on the recirculation of water discharged around the impoundment through the organic cover, is tested on the site. Available data gathered in 1998 and 1999 shows that the pH of recirculated water flowing within the wood waste cover increases by 2 to 4 units and that Fe,, concentrations decrease by a factor greater than 6.

Jan 1, 2000

By Daniel P. Coughlin, Robert C. Thomas, Christopher S. Romanek, Kristian W. Paul

Two separate constructed treatment wetland (CTW) systems receiving the same metal contaminated, acid sulfate water over different lengths of time and at different rates were evaluated for metal attenuation. Both wetlands are the alkalinity generator portion of a succesive alkalinity producing system (SAPS). Sequential extractions are employed to determine phases of metal removal. Results indicate that Fe, Al, Zn, Ni. and Cu accumulate in the organic substrate over time. Manganese accumulates initially, but is not retained in the system over time.

Jan 1, 2000

By Corale L. Brierley

This paper lists commercial bioheap and stirred tank bioleach operations and explains the status of these operations. A total of 17 commercial-scale bioleaching plants have been commissioned. Bioleaching plants are divided into two technology applications: bioheaps and aerated stirred­tanks. In bioheap leaching, secondary copper ores or sulfidic refractory precious metal ores are crushed and bioleached on pads. Stirred-tank technology is used to bioleach base and precious metal concentrates.

Jan 1, 1999

By Günter Strappler, Max John

When tunneling through karstic terrain, diverse and complex karst structures are to be expected. By means of drilling ahead of the face using drill jumbos, these structures can be detected to such a degree that by applying proper support measures both open karst cavities and karst holes surrounded by boulders embedded in soft rock can be mastered without causing any break-outs. Support measures such as spiles ahead of excavation, sealing off cavities, back?lling with sand, etc. have to be planned schematically and adapted to the dimensions and formations of the karst structures on site. An essential requirement for a smooth excavation procedure is the availablility of all necessary tunneling equipment for excavation by drill and blast as well as for excavation of soil, with experienced tunnel engineers being in charge of any adaptions on site.

Jan 1, 2003

By L. W. Saperstein, MJ. Carlson

With the goal of improving the strength characteristics of pneumatically emplaced material used for localized subsidence control, the binding additives fly ash, bentonite, and portland cement were examined for their effect on the support capabilities of coal refuse. It was found that, within certain concentration ranges, all three offered some increase in the ultimate strength of the backfilling mixture. However, portland cement gave the greatest percentage increases. Selection of the appropriate backfilling mixture will allow for the most economical and efficient subsidence control when pneumatic stowing is employed.

Jan 1, 1990

By Christopher P. White, John R. Wagner

This paper will discuss the complex and difficult soil conditions encountered in the sinking of 15 shafts of 18m to 27m depth and the excavation and lining of 6700m of 2.74m dia. interceptor sewer on Staten Island, New York. The complex soil profile consists of dense glacial till and sand outwash strata overlying the much older cretaceous sand, silt and clay strata. The tunnel varies from 8m to 14m below the nearby sea level. A significant amount of boulders were anticipated in the till. therefore, a decision was made to excavate the tunnel with a digger shield installing bolted, gasketed concrete segments. The bid documents stated the soils were dewaterable. Several conditions occured in this complex soils matrix which required modifying the planned means and methods including the necessity to use compressed air. The conditions encountered and the equipment used will be described.

Jan 1, 1991

By D. X. Tang, G. Wilson, Y. Luo, S. S. Peng

Knowing the location of voids/fractures in roof rock will be greatly helpful for roof support design. The drilling parameters obtained during normal roof bolt installation cycle provide a fast and economic way for determining void location in roof rock. In this research, feed pressure and rotation torque are found to be good indicators for identifying the voids, based on the results of a series of laboratory experiments. A set of computational rules has been developed to locate voids in mine roof using the measured roof drilling parameters and implemented in MRGIS, a software package developed to allow mine engineers to make use of the large amount of roof drilling parameters for predicting roof geology properties automatically. Anew feature, 2D map+3D figure display, is also added to MRGIS.

Jan 1, 2004

By L. B. Hales

Color video or digital cameras have been installed over flotation cells to monitor color, bubble size, froth movement, and other characteristics. These systems are designed so that the camera provides flotation performance information just as any other sensor might. Factorial tests have been run to monitor and measure the variation in froth characteristics as a function of flotation control settings. Ultimately, it is envisioned that froth image sensors can be used to monitor and control the flotation performance as effectively and for less cost than current analytical systems.

Jan 1, 1999

By R. J. Puchala, B. M. Hawrylewicz

High voltage electrical discharge in water causes instantaneous release of accumulated energy into water. The experiment described in this paper regards the utilization of the electric discharge phenomenon in rock splitting. The pressure in the shock waves created by the discharge inside a small volume of water enclosed in solid rock causes stresses which can result in breakage of rock. Holes drilled in tested samples were notched in order to weaken the tensile strength of the rock and achieve a uniformly directed split. The influence of the notches was theoretically analysed and compared with experimental data. Results of the tests have been statistically elaborated in order to correlate the newly-created surface to the energy supplied.

Jan 1, 1986