Search Documents

By H. K. Lin

Elemental sulfur is founded to be the predominant sulfur-containing species in a leaching residue resulting from ferric chloride leaching, under given conditions, of a chalcopyrite concentrate. The mineralogical study of the leaching residue which consists of 52% elemental sulfur reveals that the sulfur formed at the end of leaching process is in the form of discrete crystal rather than coating film. Flotation has been applied to recover the sulfur successfully using xanthate as a collector. Dispersants arc needed to prevent the mechanical entrapment of silicate and quartz by sulfur. Very high recovery of sulfur with satisfactory grades can be achieved with a relatively simple notation scheme.

Jan 1, 1991

By M. J. Sapko

From 2001 to 2007, the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) conducted studies to develop alternative methodologies to full-scale explosion testing for deter-mining the ultimate strength of mine seals. As a result, the PRL developed and proposes an alternative seal-strength evaluation method based on a hydrostatic pressure-loading concept. The researchers suggest pressure loading a seal using water to twice the expected dynamic design load. The hydrostatic chamber test offers a means of validating seal designs, establishing appropriate resistance functions and determining the ultimate strength of seals through testing to failure. This article contrasts the full-scale explosion and hydrostatic testing of mine seals using a simple dynamic system model and principles.

Jan 1, 2008

By Montaser S. El‑Salmawy, AHMED A. S. SEIFELNASSR, Ahmed Al‑Abady, Abdeaziem M. Abdelaal, Amr F. M. Ibrahim

Iron is a key detrimental impurity in silica sands that determines their contribution to high-technology industries. Herein, a simple ecologically sound approach is investigated for iron removal from a silica sand sample obtained from the El-Zaafarana area-Egypt. The sample was subjected to a detailed microscopic mineralogical study supported by XRD and XRF characterization. The sample was beneficiated using distilled water attrition scrubbing and screening over a 25 μm sieve followed by leaching using a mixture of equal amounts of phosphoric and oxalic acids. Leaching experiments were designed and analyzed using the Box-Behnken design (BBD) methodology. A model was developed and evaluated using the analysis of variance technique to map the relationship between the residual iron oxide in the produced concentrate and selected variables such as leaching temperature, oxalic acid, and phosphoric acid concentrations. XRD and mineralogical analysis reveal that quartz is the most dominant constituent of the studied sand and other minerals such as kaolinite, iron oxide, rutile, and zircon exist in trace amounts. The head sample shows a silica and iron oxide content of 95.69% and 2379 ppm, respectively. Attrition and separation over a 25 μm sieve increase the silica content to 97.05% and decreases the residual iron oxide to 455 ppm. The final product after leaching under optimized conditions shows 99.82% silica and 55 ppm iron oxide.

Aug 30, 2022

By William G. Pariseau

Solvay Chemicals Company mines trona in south-central Wyoming and has done so for many years. The mine is one of several in a mid-continent sedimentary basin that hosts the largest trona resource in the world. Trona is an evaporite, a sesquicarbonate that occurs in several seams of varying thicknesses and depths. Trona is processed into soda ash which has a number of industrial uses in the manufacture of glass, detergent, paper and chemicals. Figure 1 shows the location of the Solvay Mine. A ventilation shaft was recently excavated at Solvay Chemical Company’s mine in the trona patch. In fact, a 22 ft (6.7 m) diameter shaft (inside diameter) was bored upwards from the 1500 ft (457 m) level to the surface. The first bored section was 26 ft (7.9 m) in diameter that allowed for a 2 ft (0.6 m) thick concrete liner. This section began at a depth of approximately 1500 ft (457 m). A second bored section was 24 ft, (7.3 m) in diameter that allowed for a 1 ft (0.3 m) thick concrete liner. This section began at a depth of approximately 750 ft (229 m). This shaft is the #5 Shaft. Figure 2 shows the cutter head used to excavate the shaft.

Feb 1, 2025

By Josh B. Taggart

Some twenty to twenty-five years ago we saw the beginning of mechanization in our coal mines, It has now progressed to the point Chat as instruments of production the pick and shovel are things of the past, They had to give way to better and more efficient methods--so mechanization, followed by and combined with automation, has become common-place in our mines. Our coal could not keep its competitive position without this progress Without it our industry could not look to the future with any degress of confidence. Today we lock back and see cases of regained and salvaged markets. We see better coal products being produced at decreasing costs. We see better utilization of manpower and a stronger, more confident industry, Our hats arc off to those mining men, equipment manufacturers, labor leaders, and others who had the foresight to work toward these ends and the ability to bring them about.

Jan 1, 1962

By S. Rukhaiyar, M. Ramulu, G. Pradeep, P. K. Singh, P. B. Choudhury

The drill and blast method is the most prominent rock excavation method used in mining and civil engineering projects. The ground vibration is the most undesirable effect of the blasting and needs to be controlled. The blasts are designed so that ground vibration at nearby structures must remain under the prescribed limit. Various empirical blast vibration attenuation models have been presented to estimate the ground vibration for designing purposes. These models assume ground vibration as a function of distance and maximum charge per delay. United States Bureau of Mines (USBM) model is most commonly used for the blast design. However, the uncertainty associated with these models is seldom characterized, thus diminishing its reliability. The probabilistic Bayesian approach associated with the Monte Carlo method can easily quantify uncertainties associated with the model and its parameters. Thirty-three blast vibration observation data from a granite quarry in Kerala, India, is used to estimate the probability distribution of model parameters. Markov Chain Monte Carlo (MCMC) approach is used for sampling 12,000 samples for obtaining the posterior distribution of parameters. The uncertainty associated with model parameters is quantified from the posterior distribution, and this is further used to estimate the credible and prediction limits of the model. The point estimate of the most optimum value of the parameter is estimated using maximum-aposteriori or MAP estimate. The model parameters are also obtained using the commonly used least-square error method, which is a maximum likelihood estimation or MLE approach. It has been observed that the accuracy of the model obtained using both MAP and MLE approach is almost equal. However, the MAP estimate as per Bayesian probabilistic analysis has the added advantage that it can estimate the uncertainty of parameters as well as the model, which is not possible using the MLE approach.

Sep 27, 2021

By Roy Woodall

Successful mineral exploration is the lifeblood of the mining industry. Contrary to what the environmental lobby would have the world believe, the industry is replacing the metals it is extracting. The reserve base has not changed significantly in 20 years (Fig. 1.) Mineral exploration is a research activity. First there is the idea, the vision or the intuitive thought. The experiments follow. These involve repeated phases of data gathering, data interpretation and concept testing through drilling. For many companies, exploration is the main investment in scientific research. Each mineral exploration experiment may involve years of costly work. Despite the improving tools of science and technology, the investment remains high-risk. Only the promise of high rewards, or desire to survive as a mining company, will stimulate the necessary commitment and level of investment. Confidence that an economic return can be achieved, confidence in the science and technology being applied and confidence in the people involved are the foundations upon which successful mineral exploration is built (Woodall, 1984). The challenges facing the explorationist in the 1990s fall into two categories: - the challenge to make the activity economic; and - the challenge to make the activity socially and, therefore, politically acceptable.

Jan 1, 1992

By M. F. Bradley, G. M. Schoen

The Magmont Mine, a 50/50 venture between Cominco American Incorporated (the Operator) and Dresser Industries, Inc., (Halliburton), is a metallic mining and milling facility in the new lead belt of Missouri. The mine is located approximately 100 miles southwest of St. Louis. Legislation passed in 1992 by the Missouri legislature requires all metallic mining and processing facilities to apply for a Metallic Minerals Waste Management permit (MMWM) for their waste facilities. Regulations were subsequently promulgated by the Missouri Department of Natural Resources (DNR). Cominco obtained a MMWM permit (MM-006) from the Missouri DNR in 1992.

Jan 1, 2001

By Gary Peach, Peter Mason

Planning and estimating progress rates and costs for tunnelling is always best done based on experience and historic precedent. Much precedent is available but the use of data monitoring, data mining and other retrieval techniques on modern TBM machines can enable this to be further expanded and refined. Advance rates can be related much more closely to rock types as can associated rock bolt and mesh/ shotcrete requirements. This in turn can lead to a further refinement in best likely combinations of equipment, such as shotcrete jumbos, better selected for the anticipated conditions, rather than the potential advance rates of the machine. Efficient and timely construction of the tunnel will also be linked to times needed for finishing work, such as contact and void grouting and to how this can be initiated while the TBM is still in operation, in order to save overall construction time. Indeed, this in turn may affect the most preferable layout and construction details of the permanent tunnel. Considerable experience has been gained in the use of two large diameter TBM tunnel drives through the Himalayas at the Neelum-Jhelum hydropower project in Pakistan. All the above aspects will be discussed in the paper based on the considerable experience and data which came from that operation, including appropriate measures in highly stressed areas potentially subject to rock burst.

Jun 13, 2021

Newmont?s Twin Creeks Mine, located in northern Nevada, is producing gold ore from surface mining operations. The ore is currently processed at three different on site facilities depending on the ore type and the grade. The processing facilities operate under stringent geochemical blending constraints that must be met from mine ore deliveries and off site sourced ore. To analyze various strategic options, the technical team utilizes the mathematical optimization approach. However, due to the size and the complexity of the operation, there are unique challenges in optimizing life of mine production scheduling. This paper describes those challenges and the methodology developed to take advantage of different scheduling software systems that effectively compensate each other and result in reasonable guidance. The paper also describes how those scheduling results are reflected in detailed mine plan and cost estimate work.

Feb 27, 2013

By Horst Pöchhacker

The largest structure along the Tauern highway section between Salzburg and Villach is the 6.4-km-long Tauern Tunnel. The major geotechnical problems that came up surprisingly while driving the headings of that tunnel and their successful solution form the content of this article. A detailed discussion is presented of the special construction methods developed by systematic application of the principles of the New Austrian Tunneling Method with which even very heavily squeezing ground with large excavation areas can be mastered reliably and economically.

Jan 1, 1976

By Sandip K. Mukherjee

This paper describes the application of pressure foam to control respirable dust in a double-drum longwall mining section. The feasibility of passing an adequate quantity of pressure foam through the shearer drum was initially established in the laboratory. Thereafter, underground testing of the foam system to determine its effectiveness on an active operating longwall was conducted in a mine in West Virginia. The foam system proved superior to the water spray system. The de- tails of the laboratory and field investigations, the results obtained, and the degree of acceptance of this system by the mining company are discussed in this paper.

Jan 1, 1984

By C. H. Bucknam

Classical acid-base accounting using modified Sobek titration methods has resulted in interpretation of results for materials with neutralization potential (NP) less than 20 tons of CaCO3/1000 tons of material (2% CaCO3) as "uncertain" due to lack of sensitivity within that content range. Standardization of a "fizzless" acid neutralization potential (ANP) method was undertaken in the American Society for Testing and Materials (ASTM) International using two ranges of sulfuric acid additions based on reaction pH and carbonate carbon estimates rather than subjective fizz testing as well as hydrogen peroxide additions to correct for mineral acidity. The method is identified as the acid neutralization potential acidity (ANPA) titration method. During interlaboratory testing a positive bias was discovered within the "uncertain" range which was further investigated and resolved by increasing the test sample weight from one to five grams for samples needing improved accuracy in materials with ANP <2% CaCO3. Test results from the interlaboratory testing of the low range method is presented and compared with the results from the original ANPA method in the paper.

Feb 27, 2013

By Noriyuki Fujii

It is no need to say that exploitation of industrial minerals has a close relation to development of the industries related. In the first stage, a small scale manufactures were initiated in areas producing some main raw material minerals. China and cement manufactures, for example, were established depending on the local occurrence of raw materials such as kaolin and limestone without exception. That is, the industrial development is greatly influenced by the local production of the raw materials in the stage. With the development of industrial technology, various kinds of raw material minerals are explored to meet the demands of industries in the second stage. New materials become indispensable, and low-grade raw material minerals, which were left as useless, are developed as useful materials. In the stage, the development of raw material minerals is accelerated by that of industrial technology related. However, industries mainly rely on domestic production of the min raw material minerals.

Jan 1, 1981

By Thomas E. Finch

Engineering mine design encompasses a range of situations, and each situation has its own range of detail and fineness. The most time consuming, and perhaps repetitive design situation involves evaluation of new or alternate mining methods. Many man years are consumed examing alternatives conjured up at all levels of the design team, from the number crunching engineer to the engineering manager. Many alternatives are intuitively disregarded, some are briefly evaluated and thrown out, and many others are started but not completed due to time constraints. All alternatives have similar input characteristics and evaluation procedures. In the design process, production requirements are known and equipment production capabilities are generated to determine the numbers and costs of an equipment type required to match a given situation. The end result is some comparative figure, typically cost per ton or yard upon which a decision is built. The similarity of input data and problem solving techniques lends design to computer solution. Computer aided equipment evaluation is not new to the mining industry. An existing and accepted technique is exemplified with the programs used by truck manufacturers. Given a haulage profile and production requirements, the number of anyone capacity, horsepower, tire size, gear ratio or similar characteristically identified truck can be determined. This information can be outputted in varying degrees of complexity and the results used with equally varying percentages of credibility by design or production engineers. Most engineers are willing to accept-the computer&apos;s effort with relief and a desire for belief. Although inherently more complex, the ultimate end of computer manipulation should be total mine design. This is an extremely large step in the evolution of mine design, and not many engineers, including the authors, believe the results would be directly applicable or necessarily correct. As with computer simulations of an operation, total computer design of mines requires such complex and lengthy input that each mine might be manually designed more quickly and cheaply. The existence of computer programs which initially evaluate a mining system or part of the system is upon us, however.

Jan 1, 1978

By Todd Minoski, Matthew McElhinney, Morgan Sears, Craig Compton

In an effort to advance the science underlying ground control engineering, researchers with the National Institute for Occupational Safety and Health (NIOSH) are frequently involved in field studies at collaborating mines. Often, these field studies involve visiting the mine site, instrumentation installation, and data acquisition. Each of these aspects involve potential risks to NIOSH employees. As an organization whose mission it is to promote the health and safety of mine workers, the health and safety of our workforce is paramount. This paper provides documentation of the best practices followed by NIOSH employees who are tasked with visiting and conducting work at underground and surface mines. This includes Mine Safety and Health Administration (MSHA) approved training, mine site specific training, and hazards associated with all aspects of mining that could be encountered by the employee. Additionally, this paper details best practices associated specifically with instrumentation installation including the mitigation of hazards associated with the proper equipment handling, drilling, and the mine environment. The information showcased in this paper can be used as considerations for industry practitioners such as mine operators, consultants, and academic researchers engaged in the installation of instrumentation in the field. Furthermore, the best practices detailed in this paper can be used as a foundation for agreements made between mine operators and researchers to ensure safety procedures will be followed while on mine property. This will result in enhanced safety of both researchers involved in field studies as well as mine employees tasked with assisting and accompanying those researchers.

Feb 1, 2024

By J. Drelich

The flotation limit of fine particles has been re-examined based on the effect of bubble size on contact angle, and a new surface chemistry-limited relationship describing the minimum particle size which can be floated is proposed. In this analysis the critical value of bubble-solid contact radius (re) for which there is no effective attachment between particle and bubble has to be determined. The values of re determined by extrapolation of our experimental data for contact angle versus bubble-solid contact diameter permit the prediction of the flotation limit of methylated quartz particles, with fraction-al coverage of trimethylsilyl groups from 0.07 to 0.51. The limit of fine particle flotation as determined by this theoretical approach agrees well with experimental data reported in the literature.

Jan 1, 1994

By Mark C. Russell, Charles T. Russell, Brooke Colburn, Parker Bailey, Desiree Bernhard, Kaito Durkee, Tristen Cutshall, Rob P. H. Urselmann

Hypersonic tunnel boring (HTB) uses directed, high velocity projectile impacts to remove rock. HTB is highly independent of rock strength and targets hard, abrasive rock and variable rock environments. This paper discusses history, theory and presents test (2×2 m and .75×.5 m tunnels) field trial results and technical and economic evaluation. The HTB tests are compared against the historic ‘project REAM’ and the concept against tunnel boring machines and drill & blast in design studies for full-scale 12 m and 4.5×5.5 m tunnels. The positive results indicate that under these conditions HTB can replace Drill & Blast and Tunnel Boring Machines.

Jun 13, 2021

By R. M. Imhof, M. J. G. Battersby, G. Ciernioch

Pneumatic flotation is rapidly becoming accepted in the main stream of flotation techniques. Imhoflot is a pneumatic flotation process that in recent years has undergone progressive development. It combines short flotation times with excellent selectivity by employing intense pre-aeration and dispersion. K+S GmbH (K+S), Germany, has installed a complete Imhoflot flotation plant at its Sigmundshall plant. The plant treats hard salt consisting of sylvine, halite, anhydrite and kieserite. The reason for selection was that Imhoflot achieves the required grades of plus 60 weight percent K2O whilst offering lower operating costs than conventional flotation installations.

Jan 1, 2002

By Leonardo Rosas Sánchez, Darío Ángel Bulla

"The two track road sector between Cisneros-Loboguerrero (having a length of 14 km and 11 short unidirectional tunnels) is a new highway still on construction located along the existing Highway Buga – Buenaventura (Colombia). Due to the steep topography, difficult geological/geotechnical conditions, the traditional portal construction approach was impossible to be implemented in eleven (11) of the twenty two (22) portals. In this specific project, the skewed portal approach was developed as the optimal and more effective solution. The construction time and costs of portals were reduced in 21 months and 75%, respectively. At the same time, the natural equilibrium of the slopes was maintained, thus, facilitating adequate safety factors along the useful life of the project. This document pretends to show a detailed design experience (and the construction of the entry portal of tunnel 11 (left)). INTRODUCTION The Cisneros-Loboguerrero project is a 14 km length dual lane highway, connecting productive zones with the Pacific Ocean along the current Bogota-Buenaventura highway as shown in Figure 1. The project is located at the northern side of the Dagua River Valley. The preliminary design suggested constructing portals under challenging topographical conditions, i.e., slope cuts having heights between 50 to 100 m (some having slopes > 100%) requiring complex developments and having very high risks.The entry portal of tunnel 11 (left) was the first portal successfully built by implementing the skewed portal approach. Later, this approach was used as a model for the construction of the other ten (10) portal having similar topographic and geotechnical conditions. The development of this new alternative provided a considerable reduction on the construction time of portals, thus relieving a critical path in this project."

Jan 1, 2016