Search Documents

By S. Mathur, Pradip

Polyacrylic acid (PAA) was evaluated as a selective flocculant for the dolomite-apatite system. PAA with a molecular weight (MW) of 4 million was found to flocculate both dolomite and apatite. However, the flocculation behaviors of dolomite and apatite were significantly different with 450,000 MW PAA, which was found to be the lowest molecular weight fraction capable of flocculation. In single-mineral tests with a dosage of 2 kg/t PAA, 90% of the dolomite and 35% of the apatite flocculated. Selectivity was achieved in mixed mineral tests. From a feed consisting of an 80:20 mixture of apatite and dolomite, respectively, a concentrate containing 90% apatite was obtained with a 70% recovery. The dolomite rejection was about 75%, which corresponds to a 2% MgO content in the concentrate.

Jan 1, 1997

By N. S. Tanious

This paper summarizes results from an investigation into possibly the largest coal pillar failure in the USA. The newly opened coal mine worked an 3.35 m (11 ft) seam under overburden depth that ranged from 91 to 671m (300 to 2200 ft) . The mine main entries, and the enclosed pillars, experienced a massive slow squeeze. The squeeze could not be controlled and the mains were lost. A new set of mains were driven. Entry convergence (closure) measurements were carried out behind the advancing face to monitor stability. Pillar stresses were also measured under four different depths of overburden: 229.433, 472.579 m (750,1420,1550, and 1900 ft). The strength of pillars in the new mains was calculated from the loads that triggered the failure in the old mains, using three pillar strength formulas. The stress measurements showed that the new pillars supported more load than their predicted strength, indicating that current strength formulas are inadequate under deep conditions.

Jan 1, 1992

By Roger E. Melley

Since startup of the Syncrude Canada Ltd. (SCL) oil sands facility in northern Alberta 15 years ago, numerous improvements have been made in the ore conveying system and equipment. The unique nature of the material conveyed coupled with the wide range of environmental conditions encountered results in a number of unparalleled challenges. Most of the improvements have been brought about through the use of detailed field evaluation. Numerous publications are available that detail the various aspects of conveyor technology, and a significant list of papers are presented each year adding to the knowledge in this field. In the area of power formulae in the mid- 1970s, there were two major sources for use in the design of the SCL conveyors: the Conveyor Equipment Manufactures Association Handbook, 1988, and DIN Specifications 22101: Belt Conveyors for Bulk Materials, 1982. These sources were supplemented by the knowledge of the belt and conveyor equipment vendors and from the general literature. The SCL design was based on the CEMA formula. However, it was accepted that this empirical approach had been developed for use with more conventional materials in more reasonable climates. To accommodate

Jan 1, 1993

By Terry S. Maley

Federally owned mineral deposits generally fall into one of three categories: (1) minerals locatable under the General Mining Law of 1872; (2) minerals leasable under the Mineral Leasing kt of 1920; and (3) minerals salable under the Materials Act of 1947. Unlike valuable deposits of gold, silver, copper, iron, lead, etc., which may be locatable, industrial minerals are acquired through a variety of methods depending on use, composition, and date of acquisition. Table 1 may be used to establish the method of acquisition for most industrial minerals.

Jan 1, 1987

By J. Ainsworth, W. Trudel, L. Schutz, C. L. Bolin

Newmont mine geologists have added substantial economic value developing over 1,150 tonnes into quality surface and underground gold reserves since 1986. However, the recent 5-year gold price slump from $387 to $262 per ounce has shifted mine geologists focus to optimizing open pit profitability and developing high-grade, high cash flow and low capital development underground reserves. More than $65 million projected revenue has been added to the Gold Quarry south layback following multi-departmental model reconciliation investigations. Kriged mine polygon construction, controlled blast heave and high-quality geologic advice in selective mining will have multi-million dollar beneficial impacts.

Jan 1, 2002

By Charles E. Mergentime, J. Marshall Dean

Mergentime/Loram's extension of the Washington, DC Metro Subway System includes construction of dual 1,770-foot tunnels in soft ground, a crossover structure, a fan structure and pumping station, and other related work. This paper describes the overall construction requirements of the Contract, including subsurface conditions; Mergentime's value engineering of the tunneling and compressed air contract requirement; selection of the tunnel boring machine and backup equipment; installation of the compressed air plant; the manufacture, use and evaluation of the tunnel liners; and the tunneling performances during construction of the first tunnel.

Jan 1, 1985

By Y. David

In 1990, the United States became only the second country (after China) to produce more than 900 Mt (1 billion st) of coal in a single year. US production of bituminous and subbituminous coal, lignite and anthracite totaled 933.5 Mt (1.029 billion st) in 1990, 5% more than in 1989. The production gains were largely due to the rebuilding of depleted coal stockpiles by electric utilities and a surge in US coal exports. Domestic coal consumption essentially remained at its 1989 level. A slight increase in electric utility coal consumption was partly offset by a decline in metallurgical coal use. The use of coal in other industries and in the residential-commercial sector remained virtually flat.

Jan 1, 1991

By Jerome C. Neyer

Within most of Canada and the northern third of the United States, the soils overlying bedrock are of glacial origin. Tunnelling in glacial soils presents numerous challenges to the contractor, including abrupt changes in soil type, boulders and glacial erratics, water bearing fine sands and silts, toxic or explosive gases, and glacial till. This paper examines the available techniques for geotechnical exploration in glacial soils; the relationship between subsurface conditions predicted by various techniques and conditions actually encountered during tunnel construction; and potential improvements in the planning and implementation of geotechnical explorations. Case histories of geotechnical exploration and tunnel construction in glacial soils are also reviewed.

Jan 1, 1985

By Maxine Wiber, Ross D. Gallinger, Brain A. Lewis

Poirier was an underground copper and zinc mine located in Northern Quebec that operated between 1965 and 1975. There are 5 million tonnes of acid-generating tailings, which have contributed acidity and metals to the Kananewesig and Kistabiche Creeks. The final closure plan incorporates the placement of all reactive material into the tails basin, installation of a geomembrane liner over the tailings deposit and a one metre soil layer to protect the liner. The environmental effect of the residual seepage was assessed from an ecological risk perspective. The Reclamation Plan has been accepted, and work commenced in 1998 to restore the site.

Jan 1, 2000

By J. W. Langhans, B. D. Blake

The U. S. Bureau of Mines has been investigating the application of thiosulfate to recover gold directly from low grade refractory carbonaceous ores for the past four years. Statistical experimental methods were used to determine the effects of various leaching parameters on both gold extraction and thiosulfate consumption. Seven variables were investigated, including thiosulfate, copper, ammonia, sulfite, and sulfate concentrations, leaching time, and leaching atmosphere. This information was used in face-centered cubic (FCC) surface response experiments to define the optimum leaching conditions for a low grade ore. Two models were generated from the data to predict gold extraction and thiosulfate consumption as a function of the leaching parameters. The models predicted a gold extraction of 67 pct and reagent consumption of 2 kg [S2032/mt ore at 0.25 M S2032-, 0.0014 M Cu2+, 0.27 M NH,OH, 0.00625 M SO;-,] and leaching for 16 h. Actual tests resulted in 62 pct gold extraction with 0.93 kg S2032- consumed/mt ore. Subsequent column leaching tests have further demonstrated the viability of applying this technology to recover gold from carbonaceous ores without first pretreating the material. Gold extractions in the column tests ranged from 69 to 78 pct with thiosulfate consumption ranging from 0.4 to 5.4 kg/mt ore. These results compare to <5 pct gold extraction using standard cyanide leaching conditions.

Jan 1, 1996

By Felicia F. Peng

Two modes of collector addition techniques are applied in the column flotation for cleaning ultra fine coal. The collector can be: 1) added directly into the coal slurry through the feed system; and 2) gasified collector and transported in the gas phase through the bubbles. Operating parameters of the column flotation were investigated through three phases of work plans for Pittsburgh No.8 seam coal. In present study, the column flotation using two modes of collector addition techniques were tested and compared. Ninety percent or higher combustible recovery can be achieved by using both methods. However, utilizing the gasified collector addition technique in column flotation has more potential than direct liquid addition technique to obtain the higher recovery at same collector dosage.

Jan 1, 1993

By S. B. Bhagwat

Equipment capacities of a sample of Illinois surface coal mines representing about 60% of surface production in the state were studied. Available equipment capacity was compared with the required capacity, as indicated by coal production and stripping ratios reported. Most mines sampled showed surplus equipment capacity, which if avoided, would result in substantial cost savings. The surplus capacity results mostly from market fluctuations that result in underutilization of equipment. Study findings underline the importance of market assessment at the time of mine planning and of communication between marketing and engineering arms of a coal firm.

Jan 1, 1987

More than 5,300 mining professionals from around the world attended the SME Annual Meeting and Exhibit, March 1-3 in Denver, CO. Seventy three technical sessions highlighted innovative technologies and applications for the development of mineral resources. And the exhibit featured 421 companies worldwide and 632 exhibit booths. The 1999 SME Annual Meeting had 10% international attendance Professionals from outside the United States were guests at the first SME International Reception. Other meeting highlights included the Keynote Session. This pivotal session examined the international experience of North American-based companies. Speakers presented their perspectives on international explorations and operations. Keynote speakers included Robert Buchan, Chairman an( Chief Executive Officer, Kinross Gold; Dave Baker, Director Global Mining Project Management, Caterpillar; and Leendert Krol, Vice President International Operations Newmont Gold. Ihor Kunasz, 1998 SME President, made the introductory remarks.

Jan 1, 1999

By R. E. Johnson, L. V. Araújo, B. R. Palmer, L. M. Abrantes, G. W. Warren

The behaviour of chalcopyrite - mineral specimens and a Portuguese concentrate - in 2M chloride solutions prepared from hydrochloric acid and sodium chloride, has been characterized by cyclic voltammetry. The study has shown the influence of the potential and of the presence of impurities in the reaction schemes and their relative extent. The dissolution of chalcopyrite concentrate under potentiostatic control has been investigated and found to confirm the effect of the selected potential on the surface modification/rate of dissolution. An attempt has been made to correlate the information obtained with the response of the concentrate electrode to constant current treatments.

Jan 1, 1993

By J. Patrick Powers, Arthur B. Corwin

Modern improvements in hydrogeology make it possible to predict with good reliability the performance and cost of ground water pumping systems in many tunneling situations. The testing and analysis techniques are presented. Data from the Buffalo NY LRRTS (1978-1980) illustrate the successful application of the technique for tunneling in rock. Data from the Red Hook Interceptor Tunnel in Brooklyn NY (1978) illustrate the application in soft ground. The Red Hook project also illustrates concerns for the side effects from dewatering, such as ground settlement and damage to timber structures. At Red Hook protective measures included compressed air, artificial recharge and controlled dewatering. Given the uncertainties of the underground, the possibility of unexpected situations must be considered. A hard rock sewer tunnel in Atlanta, Georgia (1982) illustrates an unexpected problem, and the emergency measures used to solve it.

Jan 1, 1985

By C. Tsatsanifos

Following closure of an old asbestos mine in Zidani, Kozani Prefecture, Greece, the geotechnical and environmental restoration of the tailings slopes was required. The geotechnical aspects of the restoration included the formation of gentler slopes to increase stability, in combination with drainage works for the same purpose. The environmental aspects of the restoration included covering the slopes with successive layers of soil in order to minimize infiltration of rainwater, and hence the potential for further transport of asbestos fibers, and to provide a suitable layer for revegetation of the slope. The paper presents results of slope stability evaluation using both limit equilibrium and finite element analyses and raises some issues related to reducing impacts to the geoenvironment when designing such restoration projects.

Jan 1, 2006

MULSIM/NL and La Model are displacement-discontinuity programs which have been used quite successfully in the past to provide detailed structural models of various single and multiple-seam mining situations. However, both of these programs required fairly complex details of the mine plan and topography to be manually input into the program, often taking several days of work. Recently, automatic mine and topographic grid generation capabilities have been added to the MULSIM/NL and La Model programs, reducing the input time requirements from days to hours. This paper discusses the algorithms used for the automatic grid generation and demonstrates the utility of the new capabilities with a case study.

Jan 1, 2003

By Leslie S. Halasz

This paper describes the techniques implemented at Randfontein Estates to develop twin-haulages at &apos;high speed&apos;. An operation which culminated in the world record advance for twin-end multiblast cyclic development in hard abrasive quartzites. A major expansion project was planned for the mine, with the sinking of a third twin-shaft system (to be known as Cooke No. 3), to raise the level of ore production from 3 500 000 to 5 000 000 tonnes per alumm. Subsequent redesign of the proposed shaft system as a single 9 m brattice wall shaft took place, reducing the planned shaft sinking period by 12 months and saving an estimated R 250 000 (U.S. $ 330 000) in sinking costs. The advancement of the Cooke No. 3 Shaft sinking and development programme necessitated a rapid excavation schedule for two interconnecting twin-haulages from the existing Cooke No. 2 twin shaft complex to provide a second means of egress. An early holing between the two shafts would provide significant financial and technical benefits. Pre-development and equipping of shaft pillar excavations would enable a rapid shaft production build up and blocking out of at least one year&apos;s ore-reserves.

Jan 1, 1983

By Robert F. Conley

This paper describes attrition milling as exemplified in rotary and vibratory mills for ultrafine grin¬ding application Without attempting to narrate the differences between various devices, generalized differences between the broad categories of rotary and vibratory milling are presented and compared with the ball mill Applications of these mills for coal, limestone, kaolin, mica, talc and iron oxides are described giving specific differences of the mineral properties that affect their behavior in the grinding mills Where applicable, specific recommendations are provided for ultrafine grinding of various industrial minerals

Jan 1, 1983

By Lee W. Abramson, Glenn M. Boyce

A dowel testing program was conducted as part of the Interstate Route H-3 Trans-Koolau exploratory tunnel project on the island of Oahu, Hawaii. The testing evaluated the performance of dowels to be used as initial ground support for two 12- by 15-meter (40- by 50-foot) tunnels within weathered basalt. The program tested four dowel types of three different lengths. Both grouted and friction dowels were tested. The program determined which dowels were more effective in carrying load and noted any special procedures that would be required during construction. This paper presents the test results and discusses how these results were used in the design.

Jan 1, 1991