Search Documents

By Gregg Sherry, Bob Gordan

INTRODUCTION This paper report presents the general case history for the construction of the North Outfall Replacement Sewer (NORS) project. A 1982 City of Los Angeles Wastewater Facilities Plan recognized that a 19.3 km (12¬mile) section of the North Outfall Sewer (NOS), from Culver City to the Hyperion Treatment Plant, was deteriorating and had insufficient capacity. Built in the 1920s of unreinforced concrete and lined with vitreous clay tiles, the originally unventilated NOS suffered considerable corrosion by H2S gas. This caused roof tile and concrete to fall to the bottom of the pipe, which, over the years, reduced the 11.9 M3/S (420 cubic feet per second (cfs)) design capacity of the NOS to a current level of approximately 8.5 M3/S (300 cfs). This worsening condition, thereby contributing to the polluting of Santa Monica Bay. This situation culminated in the State of California Regional Water Quality Control Board, Los Angeles Region, issuing a Cease and Desist Order on January 27, 1986, which required the City of Los Angeles to eliminate such dry weather overflows through a number of prescribed actions. One of these was to construct the North Outfall Replacement Sewer (NORS) by April 1, 1993. PROJECT DESCRIPTION The NORS Project involved the construction of over eight miles of tunnel and related structures. It consisted of a main tunnel conduit to convey sewage to the Hyperion Treatment Plant and four diversion lines connecting the main tunnel to major existing

Jan 1, 1993

By G. M. Wilemon, B. J. Scheiner

The Bureau of Mines conducted investigations on extracting phosphate values from fine-particle wastes generated during the mining and beneficiation of phosphate ore by leaching dried wastes using a H2SO4-methanol mixture. Although phosphatic clay waste contains up to a third of the phosphate originally present in the ore, recovery of these values represents a significant challenge due to the fine grain size of the material, the particles averaging less than one micrometer in diameter. Waste samples obtained from two Florida producers yielded phosphate extractions of 71 and 84 pct, respectively, when leached under ambient conditions and at a stoichiometric acid ratio of 1.4:l. Elevated temperatures did not improve the amount of phosphate extracted. Undesirable A12O3, Fe2O3, and PlgO impurities were largely rejected; higher grade wastes gave acids that meet established industry impurity standards and lower grade samples yielded acids that marginally fell short of the standard. Separation of the crude acids from the insoluble residues was accomplished via vacuum filtration through either filter paper or commercial filter cloths. Both filtration rates and solids retention were improved by the addition of 0.5 lb/ton of poly(viny1 acetate) (PVAc) or poly(ethy1ene oxide) (PEO) to the methanol-acid slurries. These results show potential for substantially increasing the reserves of an important domestic resource.

Jan 1, 1989

By W. M. Schafer, C. F. Luckay, D. A. King

Monitoring devices have been installed at several mine sites to assess the potential for the development of acid rock drainage (ARD) in waste rock, spent ore and tailings material. In addition, instrumentation has been designed for monitoring changes in water quality in pit lakes. These devices monitor temperature, oxygen, water movement and water chemistry in the waste rock pile. This information can be used to evaluate the current and future ARD risks and the effectiveness of caps and covers. The information can also be used in the design of other reclamation strategies that limit ARD development. The instrumentation includes nested thermistors and oxygen sensing ports, neutron access tubes, heat dissipation units (HDUs) and lysimeters. Many of the monitoring devices can be linked to a data logger and telemetry systems, enabling monitoring data to be downloaded from the office.

Jan 1, 1999

By K. Morsy, S. S. Peng

This paper deals with the causes and mechanisms of massive pillar failure in a room-and-pillar mine that employed nine-entry panel system using supersection technique under a cover ranging from 91 to 168 m (300 to 550 ft). Chain pillar squeeze and large roof-to-floor convergence were first observed at the belt transfer point on the very inby side of the main entries. It propagated outby quickly and within 24 hours it had covered an area approximately 1,250 m long by 762 m wide (4,100 x 2,500 ft). The failure was caught and stopped by a solid barrier pillar. Using computer modeling, the study indicated that the massive failure was initiated due to a combination of undersized chain pillars in some panels and weak immediate floor. Also, the study shows that the massive pillar failure expanded to a large area because of no barrier pillars between some panels and between mains and panels. Based on the computer modeling, alternative mine plans have been proposed to avoid such problems.

Jan 1, 2000

By Timothy F. Markey, Brian C. Strohm

This paper presents a case study which applies risk assessment techniques in evaluating potential environmental problems associated with past waste disposal practices at a 65 acre non-ferrous metals and metal alloys manufacturing facility. Waste management activities at the site involved a number of surface impoundments for gangue material, neutralized acid rinse waters, acid rinse sludges, demolition debris, storm water runoff, stockpiled ores, and a permitted residual waste landfill. As a result of these activities, the She contained 9 identifiable waste management areas impacted by over 35 potentially hazardous chemicals and metals. Extensive environmental data obtained from investigations at the Site revealed heavy metal and volatile organic chemical contamination in various environmental media. These data were utilized to evaluate potential risks to human health and the environment. The human health risk assessment estimated potential health risks to workers, residents, and Site trespassers under current and expected future uses of the Site. Areas of the Site were identified which were considered to present potential health concerns under the various exposure scenarios. Results from the human health risk assessment were utilized to develop cost effective risk based soil remediation goals protective of the public health and environment.

Jan 1, 1992

By S. K. Mishra, S. B. Kanungo, D. Biswal

An attempt was made to beneficiate low-grade, high-phosphorus manganese ores of the Garividi-Garbham region of Andhra Pradesh, India, by using wet high-intensity magnetic separation (WHIMS). The distribution behavior of both mass and chemical constituents in different size fractions of a typical highly weathered ore sample was studied to obtain information about the liberation characteristics of various chemical constituents. Magnetic separation indicated that in the +208-µm size fractions, P and acid insolubles were concentrated in the magnetic fractions. However, in the -208-µm size fractions, P and acid insolubles were concentrated in the nonmagnetic fraction because of a lower recovery of the magnetic fraction. Variations in field intensity between 1.3 and 1.75 T had little effect on the recovery and the grade of concentrate. The results also demonstrated that phosphorus was associated with all three major constituent phases, namely, oxides of Mn and Fe and aluminosilicate gangue minerals.

Jan 1, 2000

By S. C. Gambrell

Support characteristics of in-cycle trusses are analyzed using a photoelastic model loaded by tightening a truss in the sequence normally used in an underground mine. Stresses in the roof at its center point and at the junction of the roof and rib are examined. Effects of zero tension and unequal tension in the inclined anchor rods are presented. Effects of simulated subsidence on stress in the roof surface and on tension in the separate truss members are examined. Conclusions are drawn relating to (1) the effects of tension in the inclined anchor rods on uplift and compressive stress parallel to the roof surface, (2) the effects of subsidence on stress in the roof surface, and (3) the effects of subsidence on tension in the truss members.

Jan 1, 1987

By A. J. Hudson, M. R. Yenchek

Faulty insulators on mine trolley/track haulageways may allow leakage of currents into the mine roof, which may ultimately result in the combustion of the roof material. The National Institute for Occupa¬tional Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), devised a passive means to detect overheating insulators on di¬rect current systems. The detector consists of a spring- loaded car¬tridge that ejects a reflective streamer of white Teflon tape when subjected to elevated temperatures. The cartridge assembly can easily be installed over the outer metallic shell of an existing trolley line insu¬lator. If an insulator overheats due to ground leakage currents, the vis¬ible streamer alerts mine personnel traveling on the haulageway.

Jan 1, 2000

By Sriram Padmanabhan, Jan M. Mutmansky

The subject of quartz occurrences in respirable coal mine dusts has been of increasing concern in recent years. The primary impetus for this concern has been provided by better measurement technology that has detected an increased number of mines with high quartz content in their respirable dusts. This paper presents the results of statistical analyses of quartz levels in multi-stage impactor samples from eighteen different coal mining sections located in Pennsylvania, West Virginia, Ohio, Illinois, Kentucky, Colorado and Utah. The quartz and kaolinite determinations were then determined by combining impactor stage loadings to provide larger dust masses and applying the infrared spectrometry procedure outlined in Bureau of Mines/MSHA Method P7. The results will be presented using two categories of data collected during two separate phases of the research: (1) quartz concentration data from mines where quartz was known to be present in relatively high concentrations, and (2) quartz concentration data from mines chosen at random. The aspects of the occurrence of quartz in coal mine airborne dusts that will be reported include the size dependence of the quartz content, quartz variations with location in the mining section, and variations due to mining region. The results of the study show a strong pattern of size dependence of the quartz content in mines for which high quartz concentrations exist. A similar, though less pronounced, pattern exists in mines chosen at random. Quartz levels appear to have a varying relationship to section location and strong geographical patterns do not appear to exist in the data collected. Kaolinite content was found to be similar to that of quartz with patterns that are somewhat more consistent.

Jan 1, 1989

There has been some confusion over the selection of discount rates when performing stochastic simulations of a project's net present value (NPV) using risk- adjusted discounting techniques. Some argue that lower discount rates should be used when performing stochastic valuation simulations. This creates higher NPV values and improves the attractiveness of a project. Others argue that the discount rate should not be lowered for these simulations. This paper exposes the source of this confusion. It demonstrates that stochastic simulations do not remove the risk inherent in a project and, therefore-do not improve a project's value to the risk-averse investor. Risk-adjusted discount rates should, therefore, not be adjusted downward when performing stochastic NPV simulations. Stochastic simulations are, however, shown to he useful in several aspects of project valuation.

Jan 1, 1996

By R. P. King

Thermal pretreatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The effect of pretreatment using conventional and dielectric heating followed by quenching on the fracture characteristics of a number of single and multiphase brittle materials has been investigated using the Ultrafast Load Cell. It has been observed that very significant reductions in both fracture energies and the material integrity (damage) were achieved by heating followed by water quenching.

Jan 1, 1995

By H. F. Hennigar, D. L. Pawson, E. J. Foell

Results of an analysis of abyssal benthic megafauna based upon review of nearly 250 hours of videotape and 2149 bottom photographs are presented, and the utility and limitations of such analyses in deep sea biological studies are discussed. The images were acquired at depths of 4400-4800 m during a resource assessment cruise aboard the RV Prospector using a unique, deep-towed, television telemetry system coupled with 35-mm photography. The data review was carried out in support of NOAA efforts to provide adequate environmental baseline information before industrial exploitation of nodule deposits and concurrent monitoring begin.

Jan 1, 1991

By Leif A. Nordell, Philip E. Freeland

A paper discussing specification, methods, situations and results encountered in underground phase construction of the Rocky Mountain Pumped Storage Project near Rome, Georgia. The scope of work included excavation, rockbolt/shotcrete/wire mesh primary support and cast-in-place concrete lining of the (1) 216 m, top flared shaft, connecting 1.57 radian elbow, and 590 m tunnel to a 10.67 m finished diameter; (2) complex double bifurcation section; (3) excavation, support, installation and backfill concrete for three parallel, 135 m steel penstocks of 5.79 m finished diameter; (4) construction of a 43 m diameter reinforced concrete intake/discharge structure atop the shaft.

Jan 1, 1985

The most important event affecting the United States coal industry in 1993 was the strike by the United Mine Workers of America (UMWA). This was a series of selective strikes, beginning with a strike against four Peabody Holding affiliates on Feb. 2, following unsuccessful contract negotiations between the UMWA and the Bituminous Coal Operators' Association (BCOA). Although that strike ended on March 3, the failure to reach a new contract agreement led to walkouts at several Midwestern mines on May 10. During the summer, the strike expanded to include mines of 13 companies in seven states including Ohio, Pennsylvania, Illinois, Indiana, Kentucky, Virginia and West Virginia. About 17,000 miners were idled during the strike. As the prospects for a settlement diminished, the Secretary of Labor appointed a federal mediator. The mediation resulted in a five-year contract. In addition to increases in wages and pensions, it was agreed that 60% of new job openings would be filled by laid off and active UMWA miners. In return, companies won the right to establish more flexible work rules and scheduling of miners. While some health care benefits were expanded, the agreement established a new health care system that was designed to reduce costs. Preliminary Energy Information Administration (EIA) data indicate that US coal production fell by 5% in 1993, to 859 Mt (947 million st) (Table 1). The strike was one of the primary causes of the decline in production. Another significant cause was a 27% decline in coal exports. Also, a very small displacement of domestic coal production resulted from a rise in coal imports.

Jan 1, 1994

By Pramod C. Thakur

Sixty countries around the world mine about 5000 million tonnes of coal annually and simultaneously produce nearly 25 million tonnes (36.8 Gm3) [One tonne of methane at a temperature of 15°C and a pressure of 760 mm of mercury has a volume of 1471 cubic meters.] of methane. Many of these coal mines are very gassy and require methane drainage prior to mining as well as during mining. In spite of significant differences in the geology and reservoir properties of the coal seams, several methane drainage techniques have found universal application. The paper describes various techniques currently in use and their efficiency in recovering methane from mines. It appears that the application of state-of-the-art techniques, developed mostly in the U.S.A., can considerably increase the efficiency of methane recovery and improve the safety of mines throughout the world.

Jan 1, 1997

By Cherie M. Tilley

Dynatec Mining Contractors (Dynatec) entered into a contract with Barrick Goldstrike Mines (Barrick) to develop the deep gold ore reserves at the Meikle Mine north of Carlin, Nevada. The Ventilation and Production Shafts were started in early 1994 and were completed in December, 1995. The mine development and mine construction programs were completed in November, 1996. This paper describes the Meikle Mine development program.

Jan 1, 1997

By Arun Patel, Diane Hirsch, Pamela Moran

The Metropolitan Washington Airports Authority (Authority) has undertaken a tremendous expansion of Washington Dulles International Airport in Fairfax, Virginia, including upgrading passenger transportation between concourses. The first stage of this expansion envisioned a shallow cut-and-cover pedestrian tunnel between the Main Terminal and Concourse B with associated vertical circulation structures. At the beginning of the design contract, the Authority’s consulting team of Earth Tech, formerly Kaiser Engineers, and the Dr. G. Sauer Corporation compared the cost and disruption of constructing the tunnel as a cut-and-cover structure to mining the tunnel using the New Austrian Tunneling Method (NATM). Upon review, the Authority endorsed the latter method.

Jan 1, 2003

By D. E. Ranta, Neil D. O’Donnell, Thad B. Ostrowski

Ore reserve estimation at the Syncrude Canada Ltd. open-pit oil sands mine in Northern Alberta has evolved since the project's inception. Early techniques followed a conventional petroleum reservoir analysis format, with relatively widely spaced drill holes and semiquantitative grade data. Experience has developed a more standard mining approach, including classification of geological materials by both lithology and sedimentary origin, timely and multi-purpose drill holes, precise analytical data, empirical recovery factors, a computerized geological data base, and an orebody block model. Future efforts will involve enhancement of existing techniques, use of geostatistical algorithms, quantification of confidence limits, and improved control of the ore model by geological parameters.

Jan 1, 1992

By K. Fuenkajorn, J. J. K. Daeme

Ring tension tests have been conducted on 229 mm (9 in) diameter disks of Grande basaltic andesite and Pomona basalt with various center hole sizes in order to study the relationship between ring tensile strength and relative hole radius (hole radius/disk radius). The tensile strength, [ ] decreases as the relative hole radius, [ ] increases. A power equation, [ ] where C and R represent the coefficients of strength and shape, respectively, adequately represents the ring tensile strength as a function of relative hole radius over the range investigated. This equation can be used to distinguish the effect of the hole size from the strength results, to predict the tensile strength of a ring sample containing arbitrary hole sizes, and to approximate the critical relative hole radius of the material tested.

Jan 1, 1986

By Peter K. Weissenborn, Robert J. Pugh

The contrasting behaviour of electrolytes in inhibiting coalescence of bubbles was explained by the positive and negative distribution of anions and cations at the gadwater interface. Further, the efficiency of electrolytes which do inhibit coalescence of gas bubbles can be linked to a counter ion hydration mechanism and the effect of electrolyte concentration on gas solubility. A correlation was found between the transition concentration of electrolyte needed to prevent the coalescence of bubbles and the reduction in gas solubility. Hence, the inhibition of bubble coalescence in electrolyte solutions appears to be linked with the utilization of water molecules in the hydration of cations and a consequent reduction of water available for gas solubility.

Jan 1, 1995