Search Documents

By Ryan C. Stephan, Christopher Mark

"Some of the weakest roof in United States coal mines is found in the Illinois Basin. Historically, the Illinois Basin has also suffered from high rates of unplanned roof falls and rock fall injuries. During the past decade, however, roof fall and rock fall injury rates have fallen dramatically, and are now lower than the national average. Several technologies are responsible for the improvement. Roof screen was rarely used ten years ago, but a number of mines now use it on a regular basis to prevent rock falls and rock fall injuries. Other roof skin control fixtures and work practices have contributed as well.The reduction in roof falls is also directly attributed to enhanced intrinsic roof support. Stiffer primary bolting patterns have reduced the magnitude of roof spalling and roof sag. They have also helped create a more intact beam that is able to be suspended from longer cable bolts. Cable bolt design methodology has also contributed to this reduction in roof falls. Some early cable bolt applications were unsuccessful because they employed as few as two cable bolts per intersection. This paper describes a methodology for estimating rock loads for support design.ROOF FALL TRENDS IN THE ILLINOIS BASINAlthough the Illinois Basin has a long history of poor roof conditions and high rates of unplanned roof falls and rock fall injuries, recent data indicates a change in the trend. Roof fall rates are determined by dividing the total number of non-injury roof falls by the total number of hours worked underground. The data is considered for 200,000-man hours. While the Illinois Basin was once a coalfield experiencing roof falls at nearly twice the national average, it is now at or below the national rate. Figure 1 indicates the trend over the past 20 years. In 2008, the Illinois Basin mines experienced 5.06 roof falls every 200,000-man-hours, compared to only 0.75 in 2018.There has also been a significant reduction in the rate of rock fall injuries in the Illinois Basin coal mines, as shown in Figure 2. In 2008 there were 1.48 rock fall injuries every 200,000-man-hours, compared to only 0.43 in 2018.ILLINOIS BASIN COAL ROOF GEOLOGYThe roof rock in the Illinois Basin has been studied in the past to understand the primary causes of roof failures (Molinda et al., 2008; Thompson, 2010; Molinda and Mark, 2010). Rusnak and Mark (2000) evaluated 10,000 laboratory strength tests from 800 rock units and concluded that for shale, siltstone, and sandstone, the strength of the Illinois Basin variety was less than half that of the same rock types in Central Appalachia (Figure 3). A study of Coal Mine Roof Rating (CMRR) measurements in more than 200 US coal mines also found that weak roof was predominant in the Illinois Basin (Mark and Molinda, 2005)."

Jan 1, 2019

By N. E. Lehman

Cordilleran metamorphic core complexes in the southwestern United States are areas where middle to late Tertiary low-angle normal faulting has uncovered rocks that were at temperatures sufficient for mylonitization during the early part of Tertiary extensional faulting. Large-displacement low-angle normal faults that separate upper-and lower-plate rocks in metamorphic core complexes are termed detachment faults. The significance of Tertiary detachment faulting in the Basin and Range Province has only become apparent in the past 6-8 years, and the association of mineral deposits with detachment faults has only been recognized in the past few years as well. Crystalline rocks below detachment faults have typically undergone chloritic alteration and brecciation over a distance of a few to a few hundred meters below the fault surface (Fig. 1). Chloritic alteration and brecciation overprinted mylonitic fabrics formed during earlier ductile shearing along the down-dip projection of detachment faults. Rocks that underwent pre-Tertiary ductile deformation and prograde metamorphism were subjected, in rapid succession, to middle to late Tertiary mylonitization, brecciation and chloritic alteration, microbrecciation immediately adjacent to the fault, and subaerial exposure. Lower-plate rocks thus experienced rapid decompression and cooling as a result of tectonic denudation and isostatic uplift (Wernicke, 1981; Davis, 1983; Davis et al., 1986).

Jan 1, 1987

By M. Fan

Froth flotation is the most widely-used method of separating fine coal, especially coal with coking properties. However, froth flotation is not efficient for treating ultrafine coal and coarse coal particles. Our previous fundamental test results demonstrated that cavitation-generated nanobubbles can significantly improve coal and phosphate flotation performance over a wide particle size range. In this study, the effect of nanobubble on the flotation performances of different particle size fractions of coal was investigated using a bank of 10-liter flotation cells, a specially designed 50 mm inside diameter column and a 152 mm inside diameter column. It was found that nanobubbles that were either directly formed on or subsequently attached to the surface of coal particles during coal froth flotation process improved flotation efficiency. The use of nanobubble in a bank of mechanical cells flotation and column flotation significantly increased the flotation recovery at a given product grade. Nanobubbles increased the flotation rate constants of different coal particle sizes. The presence of nanobubbles in flotation slurry could extend the lower and the upper particle size limits for effective coal flotation.

Jan 1, 2012

By Kraig W. Grubaugh

Rapid growth in the rate of surface mining for coal has caused many states to increase the rigor and complexity of their surface mining codes. The promulgation of Federal surface mining standards may cause those states containing Federal land to amend their codes also. Presented is an up-to-date review of these codes with tabular summaries that divide the codes into operative functions. These summaries will be of use to new operators, multiple-state operators, and state officials. Suggestions are made for industrial efforts to present workable and acceptable amendments to these codes.

Jan 1, 1977

By M. P. Hoffman

The U.S. Bureau of Mines is developing a roof bolter with a computer-controlled drill head that will increase the safety of roof bolting in underground coal mines by allowing miners to be relocated to a safe area. To ensure secure anchorage, acceleration and strain data are broadcast from an instrumented drill steel to a data acquisition system. These data are analyzed, correlated, and transformed to pro-vide information about roof strata, then are sent to a supervisory computer executing National Institute of Standards and Technology's real-time control software. The supervisory computer sends setpoint commands to proportional-integral-derivative control loops to control drill thrust, position, revolutions per minute, and torque.

Jan 1, 1994

By Angela Binder, Mareike Schubert, Yichen Jiang, Sandra Nowosad, Oliver Langefeld

GermanyINTRODUCTIONThe mining industry is currently characterized by various factors such as environmental impact, resource scarcity, social responsibility and geopolitical uncertainty. The production of minerals required to meet the demand for renewable energy is expected to increase by 500 % by 2050, particularly for critical minerals such as graphite, lithium and cobalt 1. Easily accessible deposits are often depleted, meaning that deeper and more complex deposits need to be developed. Furthermore, investors’ value systems have shifted towards more sustainable practices. Alternative approaches to solving this problem are therefore currently being developed, such as the Modular Mining Systems concept for scalable and adaptable mining projects 2. Many mining companies have also taken important steps to become more sustainable, implementing measures such as proactive closure strategies, restoration programs and the development of renewable energy projects. In the European Union, laws such as the Critical Raw Materials Act and the Net Zero Industry Act support the mining industry 3,4. They see it as important for the energy transition and promote more sustainable ways of working in the industry Particularly negative environmental impacts such as land degradation, scarcity of local water resources, water pollution and greenhouse gas emissions are ingrained in society’s memory. Despite these efforts, the public image has not yet changed. To change this perception, the industry must strive to better communicate its sustainable practices and the steps it is taking towards a more responsible and sustainable future, promote transparency and build trust.Digitalization, automation and electrification are driving the digital transformation in mining. However, their implementation can lead to higher capital expenditure, limiting their adoption across the industry. Furthermore, implementing new technologies can be a daunting task for any organization. Change management comes into play when introducing such disruptive technologies. It involves preparing an organization for change, potential resistance and establishing effective communication. This helps to ensure that the implementation is successful and the benefits of the new technology are maximized. Digital transformation requires well-trained, young mining, electrical, mechatronic and software engineers with a deep understanding of information systems. Unfortunately, the industry faces the enormous challenge of attracting this younger generation, who have little interest in the extraction of raw materials. The need for action is compounded by an aging active workforce heading into retirement and the forecast of increasing demand for critical minerals.In this challenging environment, the concept of Blue Mining with its constant further developments represents a promising approach. This implies a shift from a linear to a sustainably oriented circular economy. For the mining industry, this specifically means the introduction of innovative technologies, the increased recovery of materials from waste and the consistent questioning and application of circular principles along the entire life cycle of a mine. Such a change can not only reduce the environmental impact, but also contribute to economic resilience and increased social acceptance of mining.

Feb 1, 2025

By Michael W. Lewis

The latest downturn in the world’s metal prices has forced many mining companies to focus on cost reduction and productivity improvements to remain competitive. Maintenance represents a significant part of the overall operating costs in the mining industry. A structured, proactive maintenance approach, such as reliability-centered maintenance, can achieve cost reductions and productivity improvements. Remote condition-monitoring systems are becoming commonplace because they have the potential to identify problems before failure. Detection of equipment degradation before failure will enable repairs to be scheduled, thereby reducing costs and interruptions to production. The mining industry is in the midst of uncertain times. Decreasing commodity prices, demand, head grade and capital availability along with increasing environmental requirements have put pressure on mining companies to significantly reduce costs to maintain short- and long-term viability. Corporations are looking at expansion, merger/consolidation and financial/hedging programs to achieve these cost reductions. Mines are reducing costs by eliminating all but essential expenditures, increasing production levels, reducing overtime and investing in new technologies.

Jan 1, 2000

By A. Choudhury

Deep open-pit mines are becoming increasingly common in the highly mineralized arctic and sub-arctic regions. Air inversion is a frequent occurrence in these regions, and is exacerbated by the natural topography of an open-pit mine. Due to such inversions, the air quality in open-pit mines deteriorates very rapidly. Transport of gaseous pollutants under arctic air inversion is complex and involves an interaction between flow, thermal and convective transport systems. This paper discusses the construction and validation of a three-dimensional model that simulate the flow of air and the transport of gaseous contaminants in an arctic open-pit mine and the effect of low influent velocity and large gust velocities on the contaminants profiles in the mine. It was found that while higher velocities may remove contaminants from the pit bottom, they may not remove the contaminants from the pit entirely, necessitating artificial mitigation measures.

Jan 1, 2012

The primary use of coal in the US is for electric generation. The problems associated with the use of this vast amount of coal is the central theme of these sessions. The problems discussed include: production capacity, mining problems, coal cleaning, transportation, combustion, and various environmental problems, such as health effects of coal combustion, water and air pollution, and solid waste disposal.

Jan 1, 1979

By George P. Tateosian

Merchants perform a number of functions in the copper market. As a major distribution arm of the copper industry, they secure scrap and other copper bearing materials for processing into usable refined shapes. These are ultimately sold to fabricators. Merchants ' hedging and arbitrage activities help keep values in proper relationship from product to product or region to region. Through these switching and trading operations, they optimize the flow of copper from mine to consumer. And finally, merchants act as a repository for copper units during times of surplus and a stockpile from which to draw during tines of shortage.

Jan 1, 1979

By J. F. T. Agapito

OCI Wyoming mines two flat-lying trona seams that are 3- to 3.5-m- (10- to 11.5-ft-) thick, about10 m (33 ft) apart and 250-m- (820-ft-) deep at its Big Island Mine in Wyoming. Continuous miners and a yielding-pillar system have contributed to improvements in resource recovery and productivity. The use of yield pillars minimizes the stresses transmitted from the upper to the lower seam. However, yielding must not impact the good, long-term stability needed to prevent subsidence for a large portion of the mine beneath the Green River channel.

Jan 1, 2000

By J. M. King

A crucial step in the acquisition by one company of the assets of another, the acquisition of the stock of another company, or the merger of two com-ponies, is the legal due diligence which needs to be performed in order for the acquirer to ascertain or confirm the obligations, liabilities and exposures to risk that are being assumed along with the assets or corporate stock being acquired. Where the obligations, liabilities, or exposures to risk arise from existing contracts, or from pending lawsuits, administrative proceedings, or threats of these actions, those matters are relatively straightforward to discover by careful review of the files of the party whose assets or stock is being acquired. However, where a company is engaged in ongoing mining or processing operations and has operated or owned mining proper-. ties, there are many sources of liability and exposure to risk which could have major adverse economic consequences to the acquiring party and which are not revealed, or at least are not clearly delineated, by the records of the company whose stock or assets are being acquired.

Jan 1, 1990

It is crucial to reestablish a domestic rare earths minerals production industry to help secure the Nation's clean energy future, reduce the U.S. vulnerability to material shortages related to national defense, and to maintain our global technical and economic competitiveness. Given that the Chinese dominance of the rare earths market has adversely impacted supply stability and endangers the United States and its allies' assured access to key materials, rare earths should qualify as materials either strategic or critical to national security. Further, the U.S. government should facilitate the reintroduction of a globally competitive rare earth industry in the U.S. Realization of this objective requires: ? Developing domestic processing capability so that the U.S. is not primarily dependent on China as a source of rare earth ore, and almost exclusively dependent of China for processing of the ores. ? Providing a mechanism where access to Federal lands for rare earth exploration and extraction is possible, and ? Training engineers to design and operate rare earth ore processing facilities

Jan 1, 2011

By John Parianos

"Seafloor mining provides significant potential economic benefits for many Pacific nations that may be "land poor" but "coastline rich," meaning they have the potential to utilize and profit from the mineral wealth within their Exclusive Economic Zones that extend 200 nautical miles (360 km) out from their coastlines. The Independent State of Papua New Guinea (the State) recognizes this tremendous opportunity and is taking a leadership role in this emerging industry by becoming a 15% partner in Solwara 1 (with an option to increase their investment to 30%).The Solwara 1 Project has been gaining momentum since Nautilus Minerals and the State signed an Agreement on April 24. This new agreement with the State in which they have staked a minimum 15% interest as a meaningful partner, underscores the State’s continued and widespread support for the Project. Signing of this Agreement was a historical occasion and a milestone achievement for Nautilus Minerals and the people of PNG.The machinery being built for the Solwara 1 Project is taking shape. The Seafloor Production Tools are now over 90 percent complete. Assembly of the biggest tool, the Bulk Cutter, was completed in April this year and assembly work on the Collecting Machine and the Auxiliary Cutter commenced in May and June this year respectively. The Riser and Lifting system, which will be used to transfer the mined material from the seafloor to the surface within an enclosed system, is over 50 percent complete. The critical path for the Solwara Project is to secure a suitable vessel arrangement. Nautilus aims to have this completed by the end of this year."

Sep 1, 2014

By Bo Forsman

METAFORA is a simulation model for determination and evaluation of strategies for operating loader/truck systems in mining. A specific version of METAFORA was used to evaluate the haulage system at Solider Mineral's Aitik mine in northern Sweden, one of the largest open pit mines in Europe with a production of about 11.5 Mtpy (about 34000 tpd) of copper are. A production level of 34065 tpd was estimated by simulation runs with METAFORA. Using METAFORA's dispatch rules (Fixed Dispatch, Maximize Trucks, and Maximize Loaders), the truck/shovel system in the Aitik mine was simulated for evaluating alternative dispatch control strategies. The Maximize Trucks rule gave about the same total production (ore + waste) as the Fixed Dispatch rule but a 9% higher ore production. The Maximize Loaders rule gave the lowest production. The marginal truck capacity decreases with increasing number of trucks serving the same loader due to increasing waiting times. In Aitik mine the low crusher capacity results in long dumping times. If the dumping time at the crusher could be halved, the ore production would increase by 14%. The paper indicates that the use of software like METAFORA can result in a substantial reduction of time, effort and cost in shovel/truck system design and evaluation.

Jan 1, 1992

By J. B. Platt

Many utility fuel choices 1990-95 defied expectations, with utility decisions and coal market developments ever more closely linked. The Central Appalachian coal boom never occurred; clean-enough coal was developed in the hard-hit Midwest; Colorado-Utah coal surged; Pittsburgh seam production strengthened; utilities embraced Powder River Basin coal; and emission allowance prices collapsed. Competition drove productivity gains, but the future is not a simple repeat. Phase 2 brings fewer viable compliance options. Mega-railroad pricing has become a key risk factor -- will this be countermanded by merging utilities and power market competition? Revenue losses from vintage contracts are problematic. Uncertainty also plagues natural gas, in spite of unanimity across major forecasts, since recent experience has been so heavily influenced by the gas bubble.

Feb 24, 1997

By Frederick C. Moore

This paper describes the original planning which actually resulted in the opening of a new aggregate plant located in central New York State. This plant, which is now named the Skaneateles Plant of The General Crushed Stone Company is unique in that the plant itself is a departure not only in design but in concept of operation from the normal aggregate plant the company has operated in the past. Whether or not the concepts which resulted in the Skaneateles Plant are economically feasible remain to be proven by the next few years of operation. By way of background data about our company which will help set the stage for this presentation, we currently operate seventeen stone quarries in the states of New York, Pennsylvania and Virginia. These quarries range in size from 200,000 tons per year to 1,500,000 tons per year with a total annual stone production of approximately 7,500,000 tons. We also produce about 1,250,000 tons of sand and gravel at six sand and gravel plants, 300,000 cubic yards of ready mix concrete, 1,500,000 tons of bituminous concrete, aglime and other minor construction materials. In many cases we are our own best customer consuming a large percentage of the total production of our own aggregates in our various ready mix and blacktop plants. Up to the concept of the Skaneateles Plant our operating facilities have been of the permanent type as opposed to the moveable or portable type plant. The steps involved in the case history of Skaneateles will begin with the basic economic requirements, market research, geologic surveys, land acquisition, zoning and financing and carry through to the final design and construction. We will attempt to show what some of the problems were, how we interpretted them and how we proceeded to solve them. The current results are apparent and can be analysed. The success of the total concepts of the Skaneateles Plant remains for future analysis.

Jan 1, 1968

By J. Dubbert, T. H. Jones

"This paper describes a rib-control methodology that uses standing support to provide most of the lateral resistance to the rib. The method is analyzed, and its boundary conditions for rib control are described. In this method, an animal-fencing mesh product covers 80 percent of the rib surface and is sparsely bolted to the rib. Can supports or other similar stiff supports are installed primarily as roof support for the entry. As the rib spalls and dilates, the mesh catches the material and expands, pressing against the standing support. Mining proceeds, and vertical roof loads increase the normal force on the Can supports, causing friction at the top and bottom of the support to go up, thereby improving lateral resistance to rib swelling.At one mine in the western United States, this method has proved excellent at preventing the buildup of rib spall. It substantially reduces the number of bolts used for screen installation, improves installation efficiency, reduces manual labor and provides more rib coverage than many screening methods. Because standing support is typically part of the roof-control plan in longwall tailgates, no additional standing-support costs are incurred. IntroductionRib safety in underground coal mines is an oft-studied topic because ribs are high-hazard areas. An overview of early rib safety research can be found in Jones and Mohammed (2014). There is a significant difference between rib support and rib control. Support improves safety through the installation of strengthening elements, such as bolts and dowels, designed to reduce rib spalling. Although spall reduction is preferred, controlling how the rib fails is enough to ensure safety in some situations. Rib control uses external elements to provide confinement, thereby holding sloughed material in place, or to prevent falling rib material from striking mine personnel. This paper presents a study of a control method used on the pillar side of a longwall coal mine tailgate in the western United States."

Jan 1, 2015

By J. Bertisen, G. Davis

Previous analyses of small samples of mining projects have found that feasibility studies tend to well under-estimate the actual capital costs of the project. Our review of 63 mining and smelting projects completed over 4 decades confirms that as-built capital costs are, on average, 25% higher than as estimated at the bankable feasibility study stage. There appears to be little attenuation over time of this bias in capital cost estimation, at first appearing to reflect an absence of learning on the part of the consulting engineer. We instead argue that this persistence of bias is intentional, driven by a scarcity of project financing and the need to inflate the project economics in a bid to secure financing. Around this intentional bias is a considerable amount of scatter. Roughly half of all projects’ as-built capita costs fall outside of the expected ±15% of the feasibility study capital cost estimate, even after allowing for intentional estimation bias. Cost overruns of 100% or more happen in roughly 1 out of 13 projects. The data reveal that a shifted lognormal probability distribution should be used when modeling mining project capital costs in a Monte Carlo analysis.

Jan 1, 2007

By D. R. Hanson, H. Lawson

In this study, NIOSH researchers conducted a machine learning analysis to examine whether a model could be constructed to assess the probability of dynamic failure occurrence based on geochemical and petrographic data. Random forest, cluster analysis and dimension reduction were all applied. The objective of dimensionality reduction was to explore patterns and groupings in the data and search for relations between compositional parameters. Cluster analyses were performed to determine if an algorithm could find clusters with given class memberships and to what extent misclassifications of dynamic failure status occurred. A random forest analysis performed on data from the Pennsylvania Coal Sample Databank cross-referenced with accident data from the Mine Safety and Health Administration (MSHA) determined that 7 parameters of the 18 examined exerted the most influence on results. Cluster analysis on data after dimensionality reduction resulted in a hierarchal clustering algorithm finding four clusters, with one relatively distinct dynamic failure cluster, and three clusters consisting mostly of control group members but with a small number of dynamic failure members.

Feb 1, 2023