Search Documents

By Joseph Padgett

Of all the fossil fuels produced in the U. S., coal is by far the most abundant. U. S. reserves amount to an estimated 1.5 trillion tons, 2,500 times the 600 million tons produced in 1970. Although it would not be possible to recover all of this coal economically with current mining technology, a significant portion would be available given the proper circumstances. With existing technology, approximately one-eighth of these reserves is accessible, an amount which would last for several hundred years at the 1970 level of production. On the face of it, this substantial reserve should go a long way in meeting the Nation's energy needs. But coal offers special problems. As additional coal is mined and then burned, there are increased costs to the Nation's land, water, skies, and health. Hence, coal poses a dilemma because of its dual status as one of our most abundant domestic fuels and as one of our major sources of environmental degradation. Against the benefits that would be chalked up in the areas of national security, balance of trade, and economic well-being from the increased use of coal, we must enter on the debit side of the ledger the increased environmental cost. This paper reviews the use of U.S. fossil fuel, the drawbacks of coal as an energy source, the means being developed to overcome these drawbacks, and the background behind the present sulfur emission regulations relative to coal combustion. It also discusses in detail the Federal Environmental Protection Agency's (EPA's) current policies to ensure the continued use of coal as a major source of energy for fossil-fuel fired power plants.

Jan 1, 1973

By A. D. Hoagland

There are large areas on all of the continents with environments which are favorable for deposits of zinc and lead of Mississippi Valley type. In the developed countries, these environments have for the most part been quite thoroughly explored for the near surface deposits, and it will be necessary to direct more effort to the search for deeper buried deposits from which much of our future production must come. The difficulties of exploration for deep ore of this type are many and formidable, but the area of permissive environments beneath deep cover is many times as great as the area of the known near surface ore districts. It is a reasonable assumption, therefore, that numerous deposits wait for discovery and development. The finding cost, however, is certain to increase, and it is essential that concepts and techniques of exploration be improved if we are to sustain a reasonably strong productive capability into the 21st century. Exploration for deeply buried deposits requires at the outset relatively large areas of favorable geologic environment. The favorable horizons must be within economic limits of depth for the exploration as well as for the mining techniques which are currently available; and there must be some condition, design or strategy which will assure the explorer a reasonable chance of obtaining maximum benefit from discoveries which he may make.

Jan 1, 1973

By Andrew C. Katen

The mining industry faces increasing geopolitical risk in the coming decades. Constraints such as resource nationalism, corruption and social license could grow to outweigh fundamental limitations like geology or supply and demand (Ernst & Young, 2013; Verrastro et al. 2010). Lurking beneath these more immediate and palpable concerns, however, may be more significant risks entrenched in geography and history. Deep-rooted cultural and strategic forces that emerge slowly ? or erupt suddenly and unexpectedly ? can generate momentous and far-reaching political, social and economic changes. While multinational enterprises routinely assess for political risk, the nature of minerals extraction means long-term and systemic geopolitical conditions are especially important for mining companies to identify and understand. Mine development is a decades-long process that binds companies to the land and makes changing course to avert emerging threats a difficult and costly option. Consequently, geopolitical assessment is a pertinent and valuable tool that mining companies can use to more comprehensively evaluate strategic threats and opportunities. Geopolitics is the study of society, politics and strategy through the lens of geography (Gray, 1996). Its emphasis on relatively permanent physical features of the earth makes geopolitics a uniquely valuable tool for assessing political risk. Topography, climate and natural resources have shaped, constrained and motivated peoples and governments throughout history. These influences transcend regimes, policies and borders ? and even states themselves ? which, by contrast, change often and dramatically. Framing politics against mountains, deserts and rivers supports identification of historical patterns and forecasts of emerging trends. In other words, the physical map provides an objective and consistent model for studying a subjective and dynamic subject such as politics (Sloan and Gray, 1999). Consequently, geopolitical assessment can highlight threats and opportunities that go unaddressed by other risk methodologies that emphasize current conditions (Glancy, 2012). Taken together, the permanence of geography, hindsight afforded by centuries of political history, and interconnectedness of world events makes geopolitical assessment a valuable approach for conceptualizing strategic risk.

Mar 1, 2014

By E. A. Metz

Work related pulmonary diseases are in the top TEN causes of occupational disability and death in the United States. Likewise, it also ranks high inmost of the other industrial countries. It is difficult to know the true occurrence of occupational lung disease because of poor documentation. This is especially true when one examines workers’ compensation claims. Most frequently, silica and asbestos are paramount in our discussion of work related pulmonary disease. Little consideration is given to other “dust-related” diseases, irritant reactions, reactive airway responses, and hypersensitivity reactions. The major classification of occupational lung diseases will be discussed. This includes both acute and chronic disease that arises in the work place, especially, the mining industry. It’s more important to make an accurate evaluation and diagnosis for the prevention of disease among other workers.

Jan 1, 2000

By Russel Delmar

Construction of Ontario Power Generation?s 12.8-m diameter, 10.4-km long water diversion tunnel in Niagara Falls, Ontario, is underway. The tunnel is being excavated by means of a 14.44-m diameter open gripper Tunnel Boring Machine. The tunnel lining is constructed as a two-pass system with the initial lining consisting of rock bolts, mesh, steel channels or ribs, and shotcrete, and the final lining consisting of pre-stressed cast-in-place concrete with a waterproof membrane. This paper describes salient design and construction aspects as follows: ? Regional and Site Geology ? Tunnel Layout and Design ? TBM Tunnelling and Cast-in-place Concrete Lining Construction

Jan 1, 2008

By PETER ROBINSON, KEVIN BARBER, OLIVER WHATNALL

Investigation and uptake of filtered tailings continues to grow throughout the globe. This is driven by a wide range of site-specific considerations, which include such factors as tailings characteristics (e.g., amenability to filtration), production rates, climate, water availability, cost drivers, environmental requirements, and social factors. Despite the aforementioned technological growth, the currently available filtration technology is not able to meet the needs of many operations and projects that would otherwise adopt the technology. Experience with large-scale industrial filtration shows that vacuum belt filter systems meet the needs of many modern users, exceptions being the inability to effectively dewater tailings at altitude and/or with a fine particle size distribution: a potential fatal flaw. This paper presents a case study on the utilization of the patented Viper Filtration technology on gold tailings to overcome this challenge and shares the resultant full-scale plant design, highlighting the features designed to overcome cost and scalability deterrents. This technology is a novel mechanical process which complements the vacuum pressure in dewatering the filter cake as it travels along the belt filter. This project commenced with a pilot testing program, which successfully met the objective to rigorously test, measure and record any performance improvements achieved when engaging the Viper technology. Of the two tailings products tested, gross improvements of 4.2%w/w and 5.7%w/w were achieved when compared to the conventional vacuum belt filter operation. This pilot testing facilitated measurement of operating and design data, which forms the basis of the full-scale system design and resultant equipment supply of three vibration roller assemblies for retro-fitting on the existing vacuum belt filter.

Jan 25, 2021

By John Trefny

Although mining is currently one of the smallest academic units on the Colorado School of Mines(CSM) campus, it is alive and well, with nearly 100 undergraduate and graduate students. For many years, Mines has had undergraduate and graduate programs in hard-rock mining. The school has recently transferred its physical mineral processing activities to the Mining Department. The program has also expanded to include tunneling, underground construction and industrial minerals. There are current discussions about increased research activities on cement and other construction materials. The Mining Department also teaches its share of what is called the “distributed core” courses with curricular requirements common to related programs, as well as mining safety and health, in conjunction with our continuing education department.

Jan 1, 2002

By Earl R. White

In 1950 Kaiser Steel Corporation acquired control of the Utah Fuel Company, a pioneer Utah coal concern owning large reserves of high volatile coking coal near Sunnyside, Utah. The mines at Sunnyside have been producing high quality coking coal since the late 1890's. Kaiser Steel acquired the coal deposits at Sunnyside in order to supply the necessary coke for its steel plant at Fontana, California. The Sunnyside coal deposits are made up of two mineable beds, the upper and lower Sunnyside seams. Both seams outcrop along the southward facing escarpment of the Book Cliffs. The coal seams dip under the massive sandstones of the Book Cliffs to the northeast at 5 to 22 pct., with the steepest-part being near the outcrop. Mining at Sunnyside up to 1961 had been carried on with room and pillar methods. The deep cover and rotten roof conditions, along with the need of increased tonnage, required a change of mining technique. Numerous ideas were presented, discussed, and economically analyzed. Several people involved in these discussions, with the aid of W.W. II, had been introduced to the European methods of coal mining, namely the longwall technique. The European mines had long been plagued with near similar conditions as those at Sunnyside, particularly the deep cover problem. The longwall method seemed to be working very well under these conditions, and with the extensive studies given longwalling by the Kaiser Steel mining officials, it was decided to give longwalling a try.

Jan 1, 1976

By F. F. von Glehn

There is no doubt that simulated ventilation networks must be adequately verified before they can be extrapolated and used for predictive purposes. There are two general approaches as to how the verification can be established and these are summarised as follows; The first approach is to measure all individual branches with trailing hoses or barometers to get individual pressure drop and flow per branch and then calculate individual resistance factors for input into the software. The simulator is run, checking that the output makes general sense (check some sensitivities if possible). The network is now considered as verified. The pressure drop to be measured is relatively small and thus it is inherent that the measured set of individual K factors will be imprecise no matter how much care is taken in the measurements and the resultant simulations will inherit the same problem. In the second approach, the network is assembled using estimated (Atkinson) K factors (based on physical features of airway, past experience and catalogued typical K factors). Only the main primary flow rates are measured and hence the relative distribution of the primary ventilation in the main airways is determined (probably about 10 off primary air flow measurements). Main critical pressure differentials at main and booster fans and across critical doors are measured (probably about 6 off primary pressure differential measurements need to be made). The simulator is run and the computer model is used to iterate and select an updated suite of K factors so that the flow balances and pressure differentials are correctly simulated (typically only 2 or 3 iterations are all that is needed). The network is now considered as verified. The pressure differences to be measured will be substantial in absolute terms and can be measured with high precision. Also, because only primary flows are measured, these will generally be measured at higher air speed points and hence improved relative accuracy. This leads to more accurate simulation results. This paper examines the advantages and disadvantages of the two approaches. 1 Background

Jan 1, 2009

By ANGELA NAIR AVELAR, Reiner Neumann, PAULO R. G. BRANDÃO

The understanding of the influence of the different types of apatite on the performance of mineral processing of igneous phosphate ores is still a challenge due to the difficulty to explain why some types of apatite floats in the froth flotation cell and others do not under the same conditions. Three types of apatite were identified by means of cathodoluminescence (CL) images in flotation concentrate and tailing samples from the Catalão mine: predominantly blue apatite, followed by green apatite and less frequently yellow apatite. The chemical composition of these types of apatite was determined by electron microprobe analysis (EPMA) and LA-ICP-MS. Blue and green apatite respond well to the process, thus remaining in the concentrate, while yellow apatite remained in the tailings. Yellow apatite is the one bearing the lowest P2O5 content and the largest anionic and cationic sites substitution, followed by green apatite, whereas blue apatite is the most homogeneous, with highest P and Ca grades and lowest substitution level. A negative correlation of the amount of phosphorus with fluorine was observed. Furthermore, impregnation of iron oxide-hydroxides in the yellow apatite was also observed. Therefore, the low flotation behaviour is due to low crystallinity coupled with impregnation onto its surface.

Jan 31, 2022

By Baojie Zhang

The main goal of this study was not only to investigate the effectiveness of the FGX Dry Separator for removing pure rock from run-of-mine coal producing a better feed stock for conventional coal preparation plants but also to optimize the FGX Dry Separator performance for producing a salable clean coal product without using the conventional wet coal preparation processes. A Model FGX-1 Dry Separator with feed throughput capacity of 10 tph was extensively tested at the Illinois Coal Development Park using two coal samples having distinctly different cleaning characteristics. Statistically designed experimental programs were conducted to indentify critical process variables and optimize FGX Dry Separator performance by systematic adjustments of critical process variable parameters. The coal cleaning performance of the FGX Dry Separator was evaluated for the particle size range of 63.5 x 4.76 mm in most cases, although FGX Dry Separator feed consisted of nominal -63.5 mm run-of-mine coals. The best cleaning performance obtained from the FGX Dry Separator is described by specific gravity of separation (SG50) and probable error (Ep) values of 1.98 and 0.17, respectively. The SG50 and Ep values for individual size fractions were as follow: 1.90 and 0.12 for the +50.8 mm size fraction, 1.95 and 0.18 for the 50.8 x 25.4 mm size fraction, 2.01 and 0.19 for the 25.4 x 12.7 mm size fraction, and 2.03 and 0.23 for the 12.7 x 4.76 mm size fraction. These process efficiency measures produced a clean coal with ash content of 13.38% from a feed coal with ash content of 34.45%. Ash content of tailings and middlings streams were 85.09% and 39.57%, respectively. Total sulfur contents of corresponding streams were 3.87%, 4.68%, 6.87%, and 4.62%. For a relatively easy to clean Illinois No 6 seam coal (Cleaning Index: 0.72), only about 0.42% of the clean coal (i.e., 1.6 float fraction) present in the feed was lost to the tailings stream. For a relatively difficult to clean coal (Cleaning Index: 0.53), about 0.98% of the clean coal present in the feed was lost to the tailings stream.

Jan 1, 2012

By R. B. Hopler

Explosives R&D has historically been motivated by coal mining. Whether to solve safety problems or to improve productivity and cost, the result has been the same: better explosives products and initiation systems. This process continues at an accelerated pace today due to the tools presently available to the explosives and mining industries.

Jan 1, 1993

By S. F. Diehl

Weathered mine waste consists of oxidized primary minerals and chemically unstable secondary phases that can be sources of readily soluble metals and acid rock drainage. Elevated concentrations of metals such as Cd, Cu, Fe, Mn, Ni, Pb, and Zn are observed in deionized water-based leachate solutions derived from complex sedex and Cu-Pb-Zn mine wastes. Leachate (USGS FLT) from the Elizabeth mine, a massive sulfide deposit, has a pH of 3.4 and high concentrations of Al (16700 ug/L), Cu (440 ug/L), and Zn (8620 ug/L). Leachate from the sedex Faro mine has a pH of 3.5 and high concentrations of Al (2040 ug/L), Cu (1930 ug/L), Pb (2080 ug/L), and Zn (52900 ug/L). In contrast, higher-pH leachates produced from tailings of polymetallic vein deposits have order of magnitude lower metal concentrations. These data indicate that highly soluble secondary mineral phases exist at the surface of waste material where the samples were collected. Sulfide minerals from all sites exhibit differential degrees of weathering, from dissolution etched grain rims, to rinds of secondary minerals, to skeletal remnants. These microscale mineral-dissolution textures enhance weathering and metal leachability of waste material. Besides the formation of secondary minerals, sulfide grains from dried tailings samples may be coated by amorphous Fe-Al-Si minerals that also adsorb metals such as Cu, Ni, and Zn.

Jan 1, 2011

By D. Kozelj

Introduction The porphyry copper deposit “Borska Reka” is the biggest undeveloped deposit in the Timok Magmatic Complex (TMC). Total reserve calculated manually is 611 Mt (cut-off grade 0.3% Cu) of 0.62% Cu, 0.21 g/t Au and 1.81 g/t Ag and 869 Mt of 0.58% Cu, 0.14 g/t Au and 1.11 g/t Ag using software. But since several deep drill holes are suspended in high grade (0.7% Cu) porphyry, total reserves could exceed 1Gt. The massive sulfide is also detected in the central (12 m at 4% Cu) and the bottom of porphyry style. Deposit was discovered during geologic exploration of deeper part of the Bor copper and gold deposit, i.e. area of high sulfidation with dominant massive sulfides. During exploitation of massive sulfide, constant explorations were carried out aimed at the expansion of reserve and discovery of new ore bodies. In that way, porphyry copper mineralization was discovered without knowing in the beginning that it was different mineralization type in regard to the ones that had been already identified and exploited. Vertical extension of porphyry is 0 m up to -1000 m sea level and not contoured along plunge. In the very beginning (1976), the exploration was focused on the shallow part of porphyry. That is because block caving method of massive underground mining was not developed at that time. Up to 1999, most of activity was related to underground exploration up to level -395 m. Geographic position The Bor deposit is located close to the industrial and University town Bor, which has over 50,000 inhabitants (census made in the year 2002). Apart from the Bor Mines, industrial complex of Mining & Smelting Basin Bor (RTB) comprises also a copper smelter (installed capacity up to 160,000 tons of blister copper) and tank house, copper wire factory, copper tube factory etc. Currently, RTB Bor is under privatization process that is going to be completed by the end of 2006. Up to date, over 20 companies have bought tender documentation.

Jan 1, 2007

By Simón Díaz‑Quezada, Ernesto Arancibia, HUMBERTO ESTAY, Tomás Vargas

In situ leaching (ISL) is an attractive technique that enables copper recovery from copper oxide ores that are either low-grade or located at depths too great to be economically exploited through conventional methods. At present, in situ leaching (ISL) has been applied to intact copper oxide ores, in particular, those which (i) present a good natural permeability and (ii) do not require preconditioning. Many copper oxide ores present low natural permeability. These are located above the water table and need preconditioning for the ISL application. The present work shows an economic assessment of the application of ISL to this type of copper ores. The preconditioning technique considered here involves the application of partial mining by sublevel stoping by removing a small fraction of the ore. This technique results in forming an ore bed with good permeability and good solution collection at the stope base. The economic assessment of this approach suggests that it can be implemented with positive net present values to copper oxide ores located at depths in the 100–300 m range, with copper grades above 0.4%. The maximum acid consumption values are below 52.5 kg/t, with blasting procedures designed to produce an ore bed with an average particle size below 6″. The breakdown of operational costs indicates that the mining cost is still very high, accounting for up to 60% of the total operating costs. Therefore, optimizing mining procedures is still necessary for improving the economic outlook of this approach and thus expanding the application field of ISL.

Feb 4, 2023

By Carlos Henrique Turolla Maia, Ulrich Maidl, Marc Comulada, Julio Claudio Di Dio Pierri

"Pure sands are typically the domain of slurry shields due to their high permeability and their granular characteristics. However, the Earth Pressure Balanced (EPB) shield machine technology has advanced in recent years with improved conditioning agents and shield machines that are equipped with slurry injection facilities and alternative mucking methods. These new so-called hybrid EPB machines have steadily increased the range of application of the EPB technology. The contribution discusses the capacities and operational features of hybrid EPB vs. slurry shield technology in pure sands. At the example of the Metro Line 4 in Rio de Janeiro (Brazil), the contribution shows that hybrid EPB tunneling in pure sands is possible and it is compared with a state-of-the-art slurry shield project as the KASIG project in Karlsruhe (Germany). Furthermore, the control of the support pressure by means of foam conditioning and slurry injection in conjunction with a close, real-time monitoring of machine parameters is discussed. INTRODUCTION Slurry shield and EPB technologies have both undergone significant developments in recent years, leading to the use of parts of one technology in the other and even to completely hybrid systems. Also the ranges of application (see recommendations by DAUB (DAUB 2010)) of both technologies have been shifted far beyond their original limits and are largely overlapping by now. Nevertheless, the basic principles of face support remain unchanged. Exploiting the possibilities of process data analysis (Maidl 2014), the interactions between the ground and the shield machine are a matter of research and have been intensely investigated. PRINCIPLES AND CALCULATION OF FACE SUPPORT PRESSURE Figure 1 shows the principles of two approaches for the determination of required support pressures: kinematic methods and numerical methods. Kinematic methods that are employed for the assessment of face stability only consider the situation in front of the TBM. The required face support force is determined by means of an assumed failure wedge that would form in ultimate limit state. Based on the ground properties, the vertical surcharge and the self-weight is transformed into a horizontal force along a virtual sliding surface. This horizontal force is to be balanced by the face support. The calculation results are amended by respective partial safety factors for water and earth pressure and the method-specific support pressure fluctuations are added."

Jan 1, 2016

The issues involved in mine closure are usually complex, and the risks are significant. Although environmental risks are paramount, other issues such as safety, community, legal, fiscal and technical factors need to he taken into account. This paper describes a simple empirical model based on the concept of the closure risk factor, which will enable decision-makers to analyze the mine closure risks at any site, regardless of the complexity of the issues and the scale, scope and location of the operation. The model enables all the issues to be captured and their individual and collective risk quantified. A number of case studies in Australia and the Pacific that illustrate the usefillness of the model are presented.

Jan 1, 2002

By Jr. Goller

You and I can visit cement plants, inspect the various rotary kiln systems and find some equipment or some burning techniques that waste energy--fuel and power. After we have made such a visit and studied a few ideas, we could recommend ways to eliminate much of this waste. Probably every idea would cost money to bring into action. For our discussion, let us arbitrarily set an upper limit of $1,000,000 on the recommendations that we are allowed to make. Call these "low-cost" or "short-term" measures. They are improvements that do not require more than say, three months to complete; they do not require a major revision to the process. Other recommendations are "high-cost" or "long-term"; they are outside the scope of this discussion. Some of our "low-cost" recommendations would offer a satisfactory return on the money that they cost; the remainder would not. Now, is there some way that we can rather quickly pick out the "low-cost" measures that will show a satisfactory return and spend our time making these improvements first? Can we separate these items from those where the return is less likely to be good? I feel that we can pick some of these items quickly if we have a kiln system that has consistently non-uniform day-to-day operation. If the operation is uniform we probably cannot pick them quickly.

Jan 1, 1977

By Arnold Hammons

Automated temporary roof support (ATRS) systems have been incorporated into roof bolters since the 1970?s. During roof bolting, many injuries have occurred from large pieces of draw rock falling inby the ATRS beam and tipping back into the operator?s area. Other injuries have occurred due to smaller, sharp rocks falling onto the operator?s hand and arm during initiation of roof bolt drilling. These injuries are attributed to weak immediate roof, sometimes called roof skin failure. Even though ATRS systems support the roof and provide a measure of protection against roof skin failure, additional hazards sometimes do exist immediately inby and outby the supported roof. Design innovations such as the ATRS mounted rocker pad deflector systems have been designed to improve the roof bolter operator safety. This paper will inform the reader of the hazards, machine evolution through different design solutions, and the current state of the art in preventing roof skin failure injuries when roof bolting.

Jan 1, 2009

By N. C. Saxena, S. K. Puri, A. K. Pal

The condition-based monitoring system is an important innovation for reducing the downtime of costly, heavy earth- moving machinery (HEMM). Vibration severity measurements were made on the HEMM located at the Gevra Project, the largest coal opencast project in India. Whenever the vibration severity levels exceeded the permissible limits, necessary actions were taken to replace the defective parts of the ma- chine. The systematic vibration monitoring of 120-t (132-st) dumpers, followed by corrective measures led to a substantial increase in component life (8.18% for an 445E Dressor and 28.44% for an MK-30 Unit Rig). The associated costs (including spareparts) were reduced by 21.55% and 25.74%, respectively. Because of the reduced downtime, savings for these two dumpers over the period from March 26 to June 25,1998, were of the order of Rs.26.47 (US$0.649) million.

Jan 1, 2000