Search Documents

By Gary G. Grim

The reliable performance of the coal reclaim system is essential to the continued availability of a coal-fired electric generating unit. The control of fugitive coal dust within the areas housing the reclaiming equipment is necessary not only to minimize maintenance and clean-up costs, but is also a safety and health consideration. This paper describes the reclaim system control and dust suppression systems as initially installed, the shortcomings of these systems and the steps eventually taken to correct these shortcomings.

Jan 1, 1983

By C. C. Muir

At the outset, I believe reference should be made to comparatively recent world developments in copper which have an important bearing upon the Canadian position. COPPER SITUATION No one can doubt the marked change for the better compared with not so long ago when less than adequate attention was paid to marketing and to uses of the metal. I need not show you graphs of world copper prices, which except for relatively brief periods and war conditions were, until about three years ago, not unlike the topography of the Canadian Rockies. There remain, of course, some non-industry factors who yearn for the old days of "roller-coaster" copper prices.

Jan 1, 1964

By R. Hogg

Based on a simplified model for the motion of particulate materials in horizontal, rotating cylinders, approximate expressions have been derived relating the power consumption of a tumbling mill to its dimensions and speed of rotation and to the amount and nature of the charge. The basic assumptions underlying the model are that there is no slip between the charge and the mill shell, that the free surface of the charge remains essentially planar during rotation and that there is no transfer of momentum from the material flowing down the free surface back to the mill shell. The relationships formulated from this model have been shown to be in excellent agreement with experimental results taken from the literature. While the requirements of the model are most closer met at low speeds of rotation, the results appear to be valid even for speeds up to 70-80 percent of the critical speed. Poorer agreement between theory and experiment is found when the charge consists of relatively large particles (balls) and when the filling of the mill exceeds 50 percent of the available volume. Qualitative explanations of these deviations have been offered.

Jan 1, 1971

By Tristan Joubert, Fabio Panella, LiLing Chen, Yung Loo, Michael Devriendt, Nasir Qureshi, Ahmad Ali

Tunnel inspections have traditionally been carried out manually by inspectors writing up observations and taking photos of defects. The results from the inspection and the defects observed are dependent upon the rigor of the inspectors and may be subject to repeatability and consistency issues and is often time consuming with elevated health and safety risks. This paper will discuss work that is being carried out in developing and implementing an innovative hardware and software solution integrating machine learning to automate the process of capturing objective tunnel condition information, offering cost and programme savings as well as health and safety improvements

Jun 13, 2023

By Gunter Swoboda, Harald Wagner

Until a few years ago tunnel construction was based exclusively on experience. In recent years, however, numerical models have increasingly become an integrated part of tunnel design [2]. These models permit good evaluation of the tunnel's support behavior even before it is designed. In particular, numerical methods are highly suited for the development of new construction methods. The prerequisite for this is the application of high-performance pre- and postprocessors, permitting the design engineer to come to a quick interpretation of the analysis results. In future, 3D analysis will take on increasing significance, for which reason this paper also deals with this type of models.

Jan 1, 1993

By L. B. Hales

Image analysis for feed belts and flotation has been used for over 20 years. It has been shown to aid in the modelling and optimization of Sag Mill circuits, and any improvements in the image analysis result in improvements in the model for control. Using a laser to measure the height-profile of rocks on the conveyor has been shown to increase the accuracy of the size classification. We have developed a system using two cameras in a stereoscopic configuration to provide height-profile measurement without the added expense and safety concerns of using a laser. Additionally, we have developed a novel technique for calibration of the system, using artificial intelligence techniques to optimize the model fit by adjusting the image analysis tuning parameters to values resulting in the best classification.

Feb 27, 2013

By B. K. Parekh

Sludge obtained during production of magnesium (Mg) metal from electrolyzing of molten MgCl2 contains entrapped magnesium particles. The sludge material containing the magnesium particles is a friable, continuous matrix of frozen salt mixture which may also contain some oxides and impurities. A dry process was developed for recovery of magnesium metal from the sludge, utilizing minerals beneficiation unit operations. The steps included selective comminution, screening, attritioning and tabling. Recovery of the high grade (+90 percent) metal was in the 70 percent range. The process is being commercially used in the U.S. The novel process was also successfully applied to a magnesium-alloy for recovery of metal from the sludges.

Jan 1, 1995

By Ralph W. M. Lai

The liquid membrane separation process was first patented in 1968 for separating hydrocarbons.(1-4) This stimulated many researchers to join in the area of separating organic compounds. l Since then, its applications have been extended to the removal of contaminants from waste water,(12-33) encapsulation of enzymes and/or microorganisms for reaction and/or separation, (24-28) oxygenation of blood (artificial lung),(19) removal of toxins from blood (artificial kidney)(26,20) and metal extraction.(31-63) This paper discusses the possible process schemes for using liquid membranes to separate and concentrate copper ion from its acidic leaching solution.

Jan 1, 1982

By L. Andrews, G. Smits, M. D. Adams, E. A. Viljoen

A new approach has been developed that is capable of ascertaining the ore component that is responsible for the preg­robbing of pregnant pulps. Many gold mines are currently treating ores containing a component that is detrimental to the recovery of gold, in that they "preg-rob" the pregnant pulp by adsorption of some of the dissolved gold. The identity of the preg-robbing component in this type of ore has been the subject of considerable debate over a lengthy period, th various suggestions including amorphous carbon, chlonte, chalcopyrite and layered silicates, such as the phyllosilicate minerals pyrophyllite, kaolinite, phlogopite and illite. A means is now available to identify and characterize the preg-robber in gold ores. This new approach consists of contacting the ore with a synthetic aurocyanide solution, identifying the mineral grains by optical microscopy and analysing each grain individually using high-sensitivity electron microprobe analysis. The approach is exemplified in this initial study by identifying the preg-robbing component in an active sample of gold-bearing shale to be an amorphous carbonaceous phase consisting of discrete particles of about 5 µm diameter interspersed with shale particles and agglomerated into grains of up to 100 µm diameter. Microanalysis of these grains as well as other mineral particles revealed that the gold content of some of the carbonaceous grains was close to 7000 g,lt, with no gold being detected in any of the other mineral phases that were found to be present (e.g. quartz, chlorite, muscovite, pyrophyllite, etc). Bulk analysis of the sample for carbon and gold confirmed that gold loadings of around 7000 g,/t would be expected if all of the gold were adsorbed onto the carbonaceous component. The carbonaceous constituent is probably also responsible for the anomalously high surface area measured for the material. It probably acts in a similar fashion to activated carbon, and the correct choice of organic blinding agent will decrease the extent of preg-robbing by lowering the activity of the material for gold, without causing any downstream problems such as fouling of the activated carbon used for gold recovery

Jan 1, 1993

By H. Marshall Farrier

In the past few years the world petroleum industry has increasingly felt the weight of changes in the principal economic factors affecting pro¬fits. As a result of, these changes, it has been necessary for many oil companies to acquire certain new facilities in order to strengthen their competitive positions and thereby protect their tremendous investments in crude oil reserves, pipe line facilities, refining operations, and marketing outlets. Principally these needs have been met by new capital outlays. A supplementary, method of acquiring needed facilities, however, has been to obtain existing facilities through complete or partial acquisition of other companies.' properties. It is this method of meeting competitive pressures with which this paper is concerned. This paper presents a statistical breakdown of the mergers and acquisitions which occurred in the oil industry between January 1, 1954, and October 1, 1959, showing the frequency' with which certain types of properties were acquired in each of the years studied. In addition, it discusses the principal economic conditions which stimulated many of these property trans¬fers, comments on the effects of these mergers on the consuming public, and indicates the types of, mergers and the rate at which they may be expected during the next three or four years. The basic data upon which the statistical analysis presented in this paper is based were taken from several published sources. Obviously they are somewhat incomplete because not all mergers and acquisitions were reported However;, a careful search was conducted through, The Wall Street, Journal, The Oil and Gas Journal, Potroleum Week, and The Oil Daily with the result that the data should be reasonably complete and comparable for each of the years studied, It is believed, therefore, that the statistical analysis which' follows provides a reasonably accurate indication of the general trend in mergers and acquisitions during the period studied.

Jan 1, 1960

By Isobel Clark

The problem of the estimation of ore reserves is essentially a simple one to describe. Given a set of sample data, at specified locations within a deposit, how can we estimate the value (or quantity) of ore in unsampled areas. The question may be posed of a whole deposit (global) or it may be more desirable to estimate smaller volumes within the planned mine area, e.g. stopes or blocks (local). Many methods have been evolved to tackle this problem, from hand-contouring of values by the mine geologist to extremely sophisticated geomathematical analysis. The main difficulty with any estimation method in this context is that it is almost impossible to check whether the "predicted" value bears a close relationship with the "actual" value. The only reliable way to decide if an estimation method has "worked" is to test the eventual value of ore against the predicted value. This is, more often than not, impossible - even allowing for the time factor involved. To know the "actual" value of a mined block it has to be sampled intensely, and these values with their positions recorded accurately. Alternatively, blocks may be passed through the concentration process individually and these results recorded. In most producing mines neither of these alternatives are practicable or seen to be-important. Another problem with comparing in-situ (so-called) mineable reserves with production figures is the introduction of many variables into the concentration process -- dilution, wastage, possible stockpiling, mill recoveries and so on.

Jan 1, 1979

By R. Stefanko

Rock bolting as a method of support continues to increase with applications in many other industries in addition to mining. Nevertheless, with nearly 55,000,000 roof bolts installed in coal mines alone last year, this remains as the single greatest use. While bolts have frequently supported ground where conventional timbering could not, there are relatively few design criteria; and trial-and-error procedures prevail. Furthermore, development of suitable instrumentation that is simple to install and readout, sensitive, durable, reliable, safe and economical in evaluating the effectiveness of a bolt over long periods of time lags behind. Therefore, the pull test continues to be the most popular method of evaluating the applicability of a certain type of roof bolt under specific installation conditions. At Penn State in the Department of Mining, research has been conducted for a number of years to measure bleedoff in carefully controlled laboratory experiments as well as in underground investigations.1,2,3,4 Unfortunately, most of the instrumentation developed has been primarily suitable only for research purposes, not possessing all of the aforementioned characteristics desirable for routine underground use. Other groups also have met with restricted success. Therefore, while relatively crude, the torque wrench continues to remain as the most widely used load measuring device. While both field and laboratory tests continue to be conducted, analytical analyses are attempted to discover the more important design parameters in order that more efficient anchorage might be devised.

Jan 1, 1969

By J. B. Seymour

This paper provides an overview of the current use of backfill for ground support in underground metal mines in the United States and a summary of recent accident data reported for these mines by the Mine Safety and Health Administration (MSHA). Backfill mines comprise a major part of the underground metal mining industry and are particularly important in terms of the fatalities and injuries impacting this workforce. Ground falls are the leading cause of fatal accidents at these mines accounting for 50 percent of the total fatalities (4 out of the 8 fatalities that occurred from 2006 through second quarter of 2011). MSHA reported several different types of accidents involving backfill at these mines. While backfill ground falls do not occur frequently, these accidents result in a much higher proportion of fatalities than host rock ground falls. Backfill ground fall accidents are especially hazardous in underhand cut-and-fill mining operations where employees work directly beneath the backfill. An analysis of recent MSHA accident data supports the need for further cooperative research with the mining industry to identify and address ground control problems in underground metal mines using backfill.

Feb 27, 2013

By R. J. Matetic, J. Noll, C. Zhou, J. DuCarme, M. Reyes, J. Srednicki

"In April 2016, the U.S. Mine Safety and Health Administration (MSHA) began requiring the use of continuous personal dust monitors to monitor and measure respirable mine dust exposures to underground coal miners. Mines are currently using the PDM3700 personal dust monitor to comply with this regulation. After the PDM3700’s implementation, mine operators discovered that it interfered with proximity detection systems, thus exposing miners to potential striking and pinning hazards from continuous mining machines. Besides the PDM3700, other electronic devices were also previously reported to interfere with proximity detection systems. MSHA sought the aid of the U.S. National Institute for Occupational Safety and Health (NIOSH) and mining industry stakeholders to determine how the PDM3700 and some other electronic devices and proximity detection systems interact with each other. Accordingly, NIOSH investigated existing standards, developed test protocols, designed experiments and conducted laboratory evaluations. Some interferences were observed to be caused by electromagnetic interference from some electronic devices, including the PDM3700. Results showed that there was no significant interference when the PDM3700, as well as other electronic devices, and the miner-wearable component of the proximity detection system were separated by distances of 15 cm (6 in.) or greater. In the present study, it was found that the PDM3700 and the personal alarm device needed to be at least 15 cm (6 in.) apart in order for them to be used simultaneously and reduce potential interference. IntroductionUnderground coal miners are exposed on a daily basis to a variety of hazards, such as coal dust exposures, high noise levels, roof and rib falls, potential for fires and explosions, and operating and working with heavy machinery. One of the hazardous jobs is that of operating or working near a continuous mining machine. According to U.S. Mine Safety and Health Administration (MSHA) statistics, 44 miners had been fatally struck or pinned by a continuous mining machine since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems have been developed and are required on all operating continuous mining machines in underground coal mines, with the exception of full-face continuous mining machines, by 2018 (MSHA, 2015a)."

Jan 5, 2018

By T. Hart

Nuclear gauging is used world-wide in almost every industry. From mining and ore-grading to finished product, the metallurgical industry is one of the biggest users of nuclear sensors for inventory, process control, and quality assurance. This paper will discuss the basic theory of gamma transmission gauging techniques found useful in mining, milling and metal production. Techniques to be discussed are gamma transmission for level and density. A major new technique will also be discussed. This technique is called gamma backscatter. The uniqueness of this technology, how to apply and the differences between transmission and backscatter will be accentuated.

Jan 1, 2011

By John B. Mitchell

Approximately 90% of all potash produced is employed as a fertilizer, either directly or with nitrogen and phosphorus. The remaining 10% is utilized in the manufacture of other chemical products, The original source of potassium was wood ash (hence the name potash), However, today the term potash refers to all commercially important salts of potassium. Sylvite, usually found associated with halite, is the predominant economic potash mineral; carnallite a lesser important source of potassium chloride, while langbeinite is important as a source of potassium sulphate. The world's first potash mining operation commenced in Strassfurt, Germany about 1860, Since that time the industry has grown steadily to its present annual volume of about 30, 000, 000 tons of potassium chloride products or 18, 000, 000 tons of K2O equivalent, potassium chloride or "muriate of potash" being equivalent to 63. 1% pure K2O, WORLD POTASH RESERVES ARE NOT EVENLY DISTRIBUTED The earth's crust contains 2 to 3 per cent potassium, mostly in the form of insoluble silicate minerals. The economically important deposits, however, are formed from brines concentrated by evaporation. The world's most important commercial deposits are of Devonian and Permian age, however soluble potassium bearing salts are presently being concentrated by evaporation in several drainage basins, notably Searles Lake, California, Great Salt Lake, Utah' and in the Dead Sea. At least twenty-four countries are known to have reserves of potash: Canada and the USSR have over 80% of the presently known world reserves, (Figure 1)

Jan 1, 1972

By Alain A. Sonntag

The MBS Solvent Extraction System utilises a unique design of mixer- settler having very high capacity per unit area and great flexibility. The development of the mixer-settler is traced through its various stages wherein the independence of mixing and pumping, reduction in settler area requirements and simplicity of plant layout were achieved. The laboratory, pilot plant and full scale tests contributing to the development of the machine are described. The existing KREBS SX plants in Europe and Africa are described as well as the plants presently under design. Results of recent testwork are also given.

Jan 1, 1981

By Osvaldo Bascur

Large metallurgical complexes have more data than a small city and much of it is "real time," changing rapidly as internal and external conditions evolve. As corporations buy and sell assets and reengineer their staff, the structures and tools that were used to understand these data are lost. This results in significant deterioration in the ability to maintain a "smart" operation. The solution is to use the sophisticated new tools built for the Internet so as to leverage information in a familiar browser format that people can use and understand. This paper describes the use of Internet technologies with plant data. Examples are drawn from existing industrial sites. Users must project where this technology will lead - standing still is the most dangerous philosophy and the only one guaranteed to be obsolete. These examples show the way to leverage existing workers with information technology.

Jan 1, 2000

By D. Lelinski

Air-sparged hydrocyclone (ASH) flotation is one of the new promising technologies. Numerous applications have been successfully tested since its conception; nevertheless, research and development efforts have continued to provide for further improvements with respect to operating conditions and design considerations. Results from experimental studies on bubbles generation in the ASH system are presented in this paper. Bubble size distributions generated during ASH operation have been determined using a high-speed photographic technique. The influence of many factors including surfactant concentration, water flowrate, and porous tube pore size has been studied. Test results indicate that these process variables have a profound effect on the bubble size distribution. With an increase in surfactant concentration or water flowrate (shear field) the bubble size distributions become narrower and shift toward smaller average bubble diameters. However, the influence of pore size is more complicated. Depending on the experimental conditions the average bubble size was found to range from about 100 to 300 microns in diameter.

Jan 1, 1995

By M. I. Brittan

A technique has been developed that analyzes routine mill operating data to determine the key operating parameters responsible for gold losses to tails. These parameters represent the prime operating variables having a dominant effect on gold recovery. The technique quantifies these effects for the specific plant being analyzed, providing a tool to optimize recovery and costs and so enhance the mine?s cash flow. The quantitative relationships generated will be different for each ore and plant: every case is site-specific and has to be treated on its merits. Examples are provided to illustrate the considerable metallurgical and financial benefits which can be realized from optimization. The examples are taken from case studies of mills in four major gold mining districts of the world.

Jan 1, 2010