Search Documents

By L. R. McCullough

To compete in Today's Market, Mine Managers have two, often conflicting tasks. They are to improve productivity, allowing the mines to compete in our world markets and to improve the environment in which our miners must work. To Maintain and improve the environment to ever increasing acceptable levels requires monitoring. In years passed this required considerable labor, which was provided by the Ventilation Department. They continuously took manual samples using hand-held instruments, sampling gas level such as CO for fire and methane for explosive risks. In addition they took continuous air velocity readings with hand-held instruments which allow them to calculate the ventilation air movement in each area of the Mine. This manual gathering of information was not only expensive and slow but marginal at best. It was marginal because the gas sampling was sporadic rather than continuous, as sample reading taken in one part of the mine would likely not be repeated for another 8 hours. If problems did occur, they likely went unobserved until they reached crisis proportion.

Jan 1, 1990

By M. T. Holroyd

Digital computer applications to minerals exploration remained largely an experimental alternative to manual techniques until well into the 1960's. Due to the high cost of computer time, and the lack of digital data and appropriate software, the most favoured applications in the early days were computationally intense tasks - those which produced the most results with the least demands for programing and data input, e.g. forward modeling. When large digitisers and plotters became affordable, the computer took over simple labour intensive tasks such as data transcription, and when software caught up, more complex tasks such as contouring. Digital data acquisition systems and superminicomputers made total computerisation of geophysical compilation and cartography possible and affordable. Applications continued to develop into areas of much greater logical complexity. Software, the new labour intensive process, still lagged behind. The microcomputer made computer applications potentially available everywhere to everyone. Desk-top micros as powerful as the minis of ten years ago can take on any geophysical exploration task currently done by computer - when the software becomes available.

Jan 1, 1989

By O. D. Staman

The risk assessment project examines the likelihood of inorganic contaminants from copper dump-leaching operations to contaminate domestic water supplies. The project examines contaminant transport by modeling contaminant movement from the base of a leach pile through the unsaturated zone and into the saturated zone. The modeling effort is unique in that it models infiltration, contaminant transport in the unsaturated and saturated zone combined with geochemical modeling of the unsaturated zone. The project incorporates probability theory to reflect the uncertainty of hydrogeologic parameters.

Jan 1, 1994

By K. Sharman

Quintette Coal Limited (managed and 50% owned by Denison Mines Limited) operates an open pit coal mine located in northeastern British Columbia, in the foothills of the Rocky Mountains. (See Fig. l). Mining commenced in 1982. The mine currently produces 4.75 million tonnes of medium volatile bituminous coal per year from three pits (Mesa, Wolverine and Shikano), using a truck/ shovel operation. (See Fig. 2). Conveyors and trucks transport run-of-mine coal to the heavy media/froth flotation process plan t, where it is cleaned and loaded into rail cars for delivery to the Ridley Island port at Prince Rupert, British Columbia. All coal is sold to the Japanese steel industry under a long term contract. The coal seams mined at Quintette are contained in the Lower Cretaceous Gates Formation. Mineable seam thicknesses vary from 0.6 m to 10 m. The regional structure of the area is typical of foreland fold and thrust belts, with open to tight folds and imbricate thrust faulting. The range of structural features found in the three pits, and their effect on mining, forms the subject of this paper.

Jan 1, 1991

By J. A. Herbst

Until the past decade, the energy-size reduction relationship was the dominant form of mathematical model used in the description of tumbling mill grinding processes (1,2). Typically, in these models some single measure of product fineness (e.g. the 80% passing size, the size modules, the specific surface area) is chosen as the dependent variable and the energy input per unit mass of material being ground acts as the independent variable. In some instances these models have been useful for the correlation of experimental data, but, invariably, they have been found to be inadequate for meaningful process simulation. During the last decade considerable advances have been made in the development of phenomenological grinding models derived from population balance considerations (3-7). In these models a set of dependent variables is employed, corresponding to the set of mass fractions which constitute the product size distribution, and energy input is abandoned in favor of "time in the mill" as the independent variable. The phenomenological models have been shown to provide accurate simulations of the entire size distribution of ground products produced in batch (8-10), locked cycle(11)and steady and unsteady state, open and closed circuit continuous grinding(12,13).

Jan 1, 1973

By Brian E. McGee

The Federal Coal Management Program represents the culmination of several years of effort by the Department of the Interior (001) to reformulate the manner in which coal owned by the United States is leased and developed. These efforts began in 1970 with a study by the Bureau of Land Management (BLM), which indicated that unless drastic changes were made in. the federal coal leasing procedures, federal coal lands would be leased almost for the asking while production of coal from those lands had been decreasing. Consequently, informal action was taken in 1971, which resulted in no further leasing being authorized until February, 1973. At that time, a formal moratorium on most coal leasing was established, with exceptions granted only for leases needed to satisfy short-term needs such as maintaining existing mines or supplying reserves for new contracts in the immediate future. This leasing policy embodied a long term objective of developing an entirely new planning system for federal coal leasing, as well as to schedule the preparation of a programmatic impact statement for this new system. As a result of the 1973 moratorium and the ensuing application of short-term criteria, only 10 federal coal leases (covering approximately 30,177 acres) were issued from February, 1973, through January l, 1976.

Jan 1, 1982

By William Gleason

"Ed Rapp is among those who believe in the saying that necessity is the mother of all invention. Rapp is the president of Caterpillar’s mining group. As such, he is tasked with leading the world’s largest mining equipment maker, and its customers, through this time of lower commodity prices, while also positioning his company to be prepared for better days that lie ahead.The decade-long mining boom fueled by growth in emerging markets and demand for commodities that led to record prices for some metals paused in 2008 with the global financial crisis. However, according to Rapp, thanks to stimulus packages around the world, and in particular the stimulus from China that was focused on infrastructure, the mining sector recovered fairly quickly, and from 2010 to 2012, mining was strong.And then the stimulus stopped. Credit dried up and global growth began to slow down and, in the three years since, commodity prices have declined by an average of 60 percent. Caterpillar expanded during the boom, acquiring Bucyrus, and investing billions into the mining sector. It has felt the pinch of the slowdown as much as any mining company in the world. These pages, and those of other mining publications as well as mainstream media, have been filled with stories of doom and gloom about the industry. But Rapp, while acknowledging that the difficult times have been painful, also said Caterpillar sees opportunity in the slow down and reaffirmed his company’s commitment to the mining industry as absolute."

Jan 1, 2014

By V. K. Gupta

A detailed experimental study of the variations in grinding rate with particle size, particle load, ball diameter, ball load, mill diameter, and mill speed was carried out for a soft cement clinker and a hard cement clinker. The effects of the ball diameter, ball load, and particle load were observed to be material (hardness) independent, and those of the particle size, mill diameter, and mill speed to be material dependent. A sharp change in grinding behavior was observed for both the clinkers at about 150 µm size. Below this critical size: (1) the hardness difference between the two clinkers became insignificant, (2) variation in the grinding rate with particle size became markedly more pronounced, and (3) mill speed had little or no effect on grinding rate. The importance of these results in the context of process optimization and control is discussed.

Jan 1, 1988

By Wayne A. Ericson, Kirk S. Davis, Cornelis Winkler

BCI has developed a chemical process known as Ecophos® for the multi-industrial Pine Level Project in DeSoto County, Florida. Approximately 85 percent of the phosphogypsum at Pine Level will be converted to a very clean gypsum. The remaining 15 percent, including impurities plus some quartz tailings sand, constitutes what is termed redigestion solids. BCI has developed an alternative to the practice of disposing phosphogypsum in large above-ground impoundments. The proposed disposal method consists of mixing the redigestion solids with clays and reacting the mixture (leached tailings) with lime prior to disposal into the mine excavations as a reclamation soil material. Leachate water quality testing using lysimeter equipment indicates that the pore water associated with neutralized leached tailings meets maximum contaminant levels set for the drinking water standards of radium and selected primary metals.

Jan 1, 1992

By Raphael Victor

The construction and modification of tunnels brings a requirement for precise measurement of convergence and divergence to safeguard the structure, maintain safety and provide the assurance needed to maintain efficient progress. Established methods include manual measurement using tape extensometers and automated methods using photogrammetry and automated total stations. Drawbacks include the need for frequent access, power supply, cabling, and cost. The paper describes how the development of reliable optical displacement sensors (ODS) has changed the landscape. ODS sensors are connected to a long-range wireless mesh communications network via a solar-powered gateway outside the tunnel, with data instantly transmitted to the internet. A sensor and its reflector target can be installed in 20 minutes and is maintenance free for a decade. Tunnel movement is measured to sub-millimeter precision with repeatability of ±0.15 mm. Integration of a triaxial tilt sensor allows slope distance to be converted to horizontal and vertical changes and allows rotational movement to be determined. Applications include new-build and long-term structural health monitoring. Case studies will be given, including the refurbishment of rail tunnels in Spain where the ODS measured movement during track lowering in a situation where no other automated system was considered viable.

Jun 13, 2023

By Michael P. Evans

Traditionally in coal processing jigs have been used to clean the coarse coal fraction, the +3/8" or +1/4" material. Today with the advent of modern fine coal jigs in the United States, its place was moved from the coarse to the inter- mediate coal circuit, the 3/8" x 100 mesh. The most economical coarse coal circuit to build and operate is a heavy media bath circuit. The following table summarizes the cost per raw coal ton processed for a coarse coal jig circuit, and a coarse coal heavy media bath circuit. The flowsheets used to compare these two circuits are shown in Figures 1 and 2.

Jan 1, 1983

Membrane technology has been available for over 36 years, but has been used sparingly in the general mining industry. However, recent developments in polymer chemistry, spiral wound element construction, pretreatment equipment and techniques and an expanded understanding of membrane fouling and cleaning techniques have dramatically improved the reliability and robustness of membrane based systems in the mining industry. Harrison Western has expanded the use of this “new” technology to enhance the use of membrane technologies to separate metals from large volume heap leach mining solutions containing copper, zinc, and iron, gold or silver. Moreover, membrane technologies are ideally suited to fractionations that add value to processing fluids from refineries like separating metals from acids or concentrating acids and producing high quality process fluids. Finally, wastewater from Acid Mine Drainage (AMD) or, as in the case of the Newmont Yanacocha Mine in Peru, the treatment of excess barren leach solution created during the rainy season, can be cost effectively processed to meet World Bank Standards for surface discharge. Polymeric membranes, specifically thin-film composites, have been developed that will purify, fractionate or concentrate gold, silver, copper, zinc or nickel. Recent applications have been developed for spiral wound modules that operate across the pH spectrum from 0 to 14. Systems using membranes have been constructed that operate on feed streams from 140° C to 300 centipoise. Opportunities exist to apply membrane technology to concentrate gold, silver, copper, zinc or nickel using thin film composite membranes. Engineered membrane types can operate across the spectrum from low pH (<2) acid applications to high pH > 10 cyanide applications. Incorporating HW EMS™ membrane technologies into current mining operations could allow one to increase production because the membrane technology would be used to pre-concentrate heap leach solutions, and therefore, increase utilization of existing extraction and refinery capabilities.

Jan 1, 2007

By K. E. Harrison

Acid rain legislation as proposed by President Bush [1], if enacted, will immediately refocus current thinking on the economic decision-making as related to coal preparation facilities. Unit operations currently ignored because of their costs, will become mandatory to coal plant designers and operators to ensure maximum energy recovery and sulfur reduction in the entire coal stream. In anticipation of this need, the U.S. Department of Energy, The Ohio Coal Development Office, EPRI and others are sponsoring research in several areas of coal preparation, and coal plant designers are beginning to consider more innovative techniques as they configure their flowsheets for plants of the future. Preparation plants then will have recleaning

Jan 1, 1990

By Norman F. Schulz

Representative sample s of typical manganiferous iron ores from the Cuyuna Range, Minnesota, were reduced to the metallic iron state at temperatures just short of fusion with an excess of coke in the manner prescribed by the R-N Direct Reduction Process. The magnetic separation characteristics of the reduced ores were determined at several grinds by means of the Davis magnetic tube concentrator. The efficiency of metallic iron concentration by magnetic separation was a direct function of the degree of metallization of the ore sample and of the degree of liberation attained in grinding. Some improvement of liberation characteristics was observed if a small amount of sodium chloride was present in the ore during reduction. Despite the extremely fine -grained structure of the crude ores, iron concentrates containing more than 90% Fe at iron unit recoveries of 90% or more were obtained from well-metallized samples of three of the four ores tested. The rejection of manganese to the tailings corresponding to such separations varied from 80 to 95%.

Jan 1, 1967

By P. Eger

Minnesota contains a major low- grade copper-nickel sulfide resource within the Duluth Gabbro Complex. Several companies have actively explored this resource. Open pit mining would be required to develop portions of the resource, and as a result, large quantities of sulfide-bearing lean ore and waste rock would be stockpiled. Although the problems associated with high-sulfide tailings and acid mine drainage are well documented, the leaching characteristics of low-grade mineralized stockpiles must be understood for environmental impact assessment, siting, and planning. The Minnesota Department of Natural Resources and AMAX have cooperated in a research program to study leaching and revegetation -of test stock- piles, Six small (1600 &apos;tons) stockpiles were constructed at the MINNAMAX Project Site and they range in composition from 0.29 to 043 g % copper, 0.075 to 0.09% nickel, and 0.6 to 1.45% sulfur. Two of the stockpiles were covered with mineral soil, one was covered with topsoil, and three were not treated Revegetation plots were established on the piles which received a soil cover. Leachate samples and flow measurements were collected at the base of the piles. Initial results indicate that metal concentrations in leachate samples range from 10 to 10,000 times the concentrations found in the streams of the area. During the first growing season, the test pile covered with topsoil yielded 30% less water than untreated test piles. No reduction in yield was observed for the piles that were covered with the less fertile mineral soil. First-year vegetative growth, expressed as biomass, was four times greater on the-topsoil pile than on the mineral soil piles. The long-term effects of vegetation on leachate quantity and quality continue to be investigated.

Jan 1, 1980

By Tom Learmont

The importance of coal in solving our energy problems has been widely discussed; the world demand for food requires increased fertilizer production and the minerals to produce fertilizer must be mined. We have seen an explosive increase in the demand for large stripping equipment. It is appropriate that we review this equipment and determine what can be done to improve productivity. While we have used coal mining as an example in the study, much of the discussion will apply equally to other forms of stripping.

Jan 1, 1975

By G. E. Tooker

This paper (1) presents new data on the use of horizontal curves to optimize the alignment of belt conveyors. The operating concept of a horizontal curve is simple. As an element of the belt passes through the curve, it is motivated to drift toward the center of the curve by unbalanced tension forces in the belt. This lateral drift is resisted by the forces of friction and gravity, which in turn can be stated as a function of drift. Resisting forces, as a function of drift, are stated in terms of variables such as the amount of load on the belt, and parameters such as the trough angle, tilt angle, and super elevation angle, and number of rolls in the idler. The trick is to determine that the belt will drift to a position of equilibrium within predictable limits, without physically constraining the edge of the belt. In practice this prediction is not easy to make without the aid of a computer. The motivating force is easy to calculate, but its value is continually changing throughout the angle subtended by the curve arc. The resisting forces are constant throughout the curve for a given drift and load condition, but the calculations are very complex. Data in this paper will assist the conveyor designer in making preliminary calculations for horizontal curves. Presented is the equation for calculating the motivating force, and a family of curves that show the resisting force as a function of lateral drift for some commonly encountered conveyor design criteria.

Jan 1, 1985

By Donald T. Mylar

It is axiomatic that in designing a bulk material handling system the primary consideration is the functioning of the machines. The structure is secondary -its reasons for being are to support, enclose and provide access to the machine, for servicing. This results in a wide variety of supporting structures. Other considerations are: plant layout, local soil conditions, climate, local laws and codes, and last, but by no means least, the Customer&apos;s wishes.

Jan 1, 1971

By F. E. du Plessis, P. De Waal

Through the development of innovative in-line mineral quantification sensors, the possibility has arisen to apply modern control theory to implement automatic process control for electrostatic high tension (“HT”) roll separators. A pilot-scale set-up was constructed to enable continuous tests to be carried out. A typical dry mill feed was continuously pre-heated and separated with a modern lab scale HT roll machine. The mineralogy as well as mass-flow of the non-conductor stream was quantified in-line, and the combined streams were re-circulated in an endless loop by a combination of vibration feeders and a bucket elevator. A fractional factorial experiment was executed to determine the most significant control parameters of the HT roll separator. Then a multi-input, multi-output dynamic model of the HT electrostatic separator was extracted by the application of standard system identification techniques for automatic control. The most important control variable to ensure a stable product grade could be identified. This allowed a robust single-input, single-output controller to be implemented. The process variable and set-point was mineral grade and the control variable was electrode voltage. Roll speed was manually adjusted while the mineral grade was kept on set-point by the control system. The roll speed, where maximum mass flow and therefore maximum yield was produced on-grade, could therefore be rapidly determined. Atmosphere humidity and ore temperature served as disturbances. Some other adjustable parameters were kept constant during the experiments, namely feed mineralogy, splitter settings and feed rate. Delivery of maximum yield, with a controlled grade, can improve production while reducing the burden of complex manual tuning. Manual tuning previously involved coping with multiple parameters with uncertain cross coupling influences on the end result. Even the end result was typically only known after completion of mineral assays. Automatic grade stabilisation and yield optimisation for a HT roll separator bank requires in-line measurement of mineralogy and mass flow, as well as the implementation of a robust process control system.

Jan 1, 2005

By E. Kenneth Siroky

The concept of ultrasonic measurement was originally applied to marine operations. Sonar . . . standing for Sounding, Navigation and Ranging, was developed for military uses. Today Sonar has become very important to the fishing fleets and marine construction industries where its applications cover a wide range of uses our company, in addition to the inair ultrasonic equipment as discussed in this paper, is also deeply involved in marine sonar and works primarily with oceanographic research and fishing industries. Ultrasonics, by simple definition, are sound waves beyond the audible range of the human ear and are generally accepted to be waves over 20,000 cycles per second. When applied to level measurement, the principles of ultrasonics are basically quite simple. A sound pulse is initiated at a point in time and the time interval for the echo from that pulse to return can be interpolated into distance. The speed of sound in air under standard conditions is approximately 1,100 feet per second, or if converted into more meaningful information as related to distance measurement, the time required for sound to travel one foot round trip is 1.78 milliseconds. An early application for ultrasonic level monitoring equipment was in large grain elevators. Prior to ultrasonics, the common practice of inventory measurement was to have an employee walk around the top of these large grain elevators, which are often over 100 feet above ground level, and drop a weighted rope or chain down into the silo to determine the level of the grain. Needless to say, this was a slow process and could be extremely unsafe, especially during windy and snowy weather conditions. An alternate

Jan 1, 1971