Search Documents

By D. R. Nagaraj

Adsorption of sulfide collectors such as xanthate on pyrite has been studied extensively over several decades using a wide variety of techniques. In spite of this, there are unanswered questions as to the identity of adsorbed species on pyrite surfaces -dixanthogen vs. iron xanthate complexes. Far less is known in non-xanthate collector systems. We have used Secondary Ion Mass Spectroscopy (SIMS) successfully in the past to obtain direct evidence for the identity of the adsorbed collector species on copper sulfides, galena and Cu-activated quartz. The present study is an extension of the SIMS analysis to investigate the adsorption of xanthate, dithiovhosphate, dithiocarbamate, and modified thionocarbamates and thioureas on pyrite. Adsorption of these collectors on chalcocite was also studied for comparison. An attempt was also made to obtain SIMS spectra for pure dixanthogens at room temperature. Only in the case of dithiocarbamate (DTC) was there direct evidence for the presence of not only the collector dimer, but also iron-DTC complexes. On chalcocite, only the copper-DTC complexes were detected (no dimer). In the case of xanthate, the collector molecular ion and its S adduct -which are possible fragments from dixanthogen -were detected on pyrite, along with a fragment peak: suggesting Fe2X. For dithiophosphate, the collector molecular ion and Fe(DTP)(OH) complex were detected (no dimer). For modified thionocarbamate and thiourea, adsorption on pyrite was negligible.

Jan 1, 1997

By G. E. Tooker

This paper (1) presents new data on the use of horizontal curves to optimize the alignment of belt conveyors. The operating concept of a horizontal curve is simple. As an element of the belt passes through the curve, it is motivated to drift toward the center of the curve by unbalanced tension forces in the belt. This lateral drift is resisted by the forces of friction and gravity, which in turn can be stated as a function of drift. Resisting forces, as a function of drift, are stated in terms of variables such as the amount of load on the belt, and parameters such as the trough angle, tilt angle, and super elevation angle, and number of rolls in the idler. The trick is to determine that the belt will drift to a position of equilibrium within predictable limits, without physically constraining the edge of the belt. In practice this prediction is not easy to make without the aid of a computer. The motivating force is easy to calculate, but its value is continually changing throughout the angle subtended by the curve arc. The resisting forces are constant throughout the curve for a given drift and load condition, but the calculations are very complex. Data in this paper will assist the conveyor designer in making preliminary calculations for horizontal curves. Presented is the equation for calculating the motivating force, and a family of curves that show the resisting force as a function of lateral drift for some commonly encountered conveyor design criteria.

Jan 1, 1985

Membrane technology has been available for over 36 years, but has been used sparingly in the general mining industry. However, recent developments in polymer chemistry, spiral wound element construction, pretreatment equipment and techniques and an expanded understanding of membrane fouling and cleaning techniques have dramatically improved the reliability and robustness of membrane based systems in the mining industry. Harrison Western has expanded the use of this “new” technology to enhance the use of membrane technologies to separate metals from large volume heap leach mining solutions containing copper, zinc, and iron, gold or silver. Moreover, membrane technologies are ideally suited to fractionations that add value to processing fluids from refineries like separating metals from acids or concentrating acids and producing high quality process fluids. Finally, wastewater from Acid Mine Drainage (AMD) or, as in the case of the Newmont Yanacocha Mine in Peru, the treatment of excess barren leach solution created during the rainy season, can be cost effectively processed to meet World Bank Standards for surface discharge. Polymeric membranes, specifically thin-film composites, have been developed that will purify, fractionate or concentrate gold, silver, copper, zinc or nickel. Recent applications have been developed for spiral wound modules that operate across the pH spectrum from 0 to 14. Systems using membranes have been constructed that operate on feed streams from 140° C to 300 centipoise. Opportunities exist to apply membrane technology to concentrate gold, silver, copper, zinc or nickel using thin film composite membranes. Engineered membrane types can operate across the spectrum from low pH (<2) acid applications to high pH > 10 cyanide applications. Incorporating HW EMS™ membrane technologies into current mining operations could allow one to increase production because the membrane technology would be used to pre-concentrate heap leach solutions, and therefore, increase utilization of existing extraction and refinery capabilities.

Jan 1, 2007

By J. A. Herbst

Until the past decade, the energy-size reduction relationship was the dominant form of mathematical model used in the description of tumbling mill grinding processes (1,2). Typically, in these models some single measure of product fineness (e.g. the 80% passing size, the size modules, the specific surface area) is chosen as the dependent variable and the energy input per unit mass of material being ground acts as the independent variable. In some instances these models have been useful for the correlation of experimental data, but, invariably, they have been found to be inadequate for meaningful process simulation. During the last decade considerable advances have been made in the development of phenomenological grinding models derived from population balance considerations (3-7). In these models a set of dependent variables is employed, corresponding to the set of mass fractions which constitute the product size distribution, and energy input is abandoned in favor of "time in the mill" as the independent variable. The phenomenological models have been shown to provide accurate simulations of the entire size distribution of ground products produced in batch (8-10), locked cycle(11)and steady and unsteady state, open and closed circuit continuous grinding(12,13).

Jan 1, 1973

By O. D. Staman

The risk assessment project examines the likelihood of inorganic contaminants from copper dump-leaching operations to contaminate domestic water supplies. The project examines contaminant transport by modeling contaminant movement from the base of a leach pile through the unsaturated zone and into the saturated zone. The modeling effort is unique in that it models infiltration, contaminant transport in the unsaturated and saturated zone combined with geochemical modeling of the unsaturated zone. The project incorporates probability theory to reflect the uncertainty of hydrogeologic parameters.

Jan 1, 1994

By P. E. Wingrove

The Kayford, Boone and Nicholas Division of Bethlehem Mines Corporation operates a modern coal preparation plant in Van, West Virginia. Since the start-up of the Van Plant in 1976 until the summer of 1980, the refuse handling system proved to be a costly maintenance problem and a material handling bottleneck. During the 1980 two-week miner&apos;s vacation the original system, which included two screw conveyors and a drag conveyor, was replaced by an installation utilizing two Flexowall steep angle belt conveyors. This paper describes the technical and economic analysis that led to the new installation and reviews its first year operating performance. The Van facility is a heavy media plant designed to handle 127 mm x 0 raw metallurgical quality coal from the Powellton seam at a maximum feed rate of 590 TPH (metric tons per hour). Depending on mining conditions, the clean coal recovery rate averages between 50 and 65%. The plant is set up with three types of cleaning circuits. Coarse material (127 mm x 12 mm) is cleaned in heavy media baths. Intermediate size material (12 mm x .5 mm) is cleaned in heavy media cyclones. Fine coal (.5 mm x 0) is cleaned in a hydrocyclone1 froth flotation circuit.

Jan 1, 1981

By William Gleason

"Ed Rapp is among those who believe in the saying that necessity is the mother of all invention. Rapp is the president of Caterpillar’s mining group. As such, he is tasked with leading the world’s largest mining equipment maker, and its customers, through this time of lower commodity prices, while also positioning his company to be prepared for better days that lie ahead.The decade-long mining boom fueled by growth in emerging markets and demand for commodities that led to record prices for some metals paused in 2008 with the global financial crisis. However, according to Rapp, thanks to stimulus packages around the world, and in particular the stimulus from China that was focused on infrastructure, the mining sector recovered fairly quickly, and from 2010 to 2012, mining was strong.And then the stimulus stopped. Credit dried up and global growth began to slow down and, in the three years since, commodity prices have declined by an average of 60 percent. Caterpillar expanded during the boom, acquiring Bucyrus, and investing billions into the mining sector. It has felt the pinch of the slowdown as much as any mining company in the world. These pages, and those of other mining publications as well as mainstream media, have been filled with stories of doom and gloom about the industry. But Rapp, while acknowledging that the difficult times have been painful, also said Caterpillar sees opportunity in the slow down and reaffirmed his company’s commitment to the mining industry as absolute."

Jan 1, 2014

By L. R. McCullough

To compete in Today&apos;s Market, Mine Managers have two, often conflicting tasks. They are to improve productivity, allowing the mines to compete in our world markets and to improve the environment in which our miners must work. To Maintain and improve the environment to ever increasing acceptable levels requires monitoring. In years passed this required considerable labor, which was provided by the Ventilation Department. They continuously took manual samples using hand-held instruments, sampling gas level such as CO for fire and methane for explosive risks. In addition they took continuous air velocity readings with hand-held instruments which allow them to calculate the ventilation air movement in each area of the Mine. This manual gathering of information was not only expensive and slow but marginal at best. It was marginal because the gas sampling was sporadic rather than continuous, as sample reading taken in one part of the mine would likely not be repeated for another 8 hours. If problems did occur, they likely went unobserved until they reached crisis proportion.

Jan 1, 1990

By K. Sharman

Quintette Coal Limited (managed and 50% owned by Denison Mines Limited) operates an open pit coal mine located in northeastern British Columbia, in the foothills of the Rocky Mountains. (See Fig. l). Mining commenced in 1982. The mine currently produces 4.75 million tonnes of medium volatile bituminous coal per year from three pits (Mesa, Wolverine and Shikano), using a truck/ shovel operation. (See Fig. 2). Conveyors and trucks transport run-of-mine coal to the heavy media/froth flotation process plan t, where it is cleaned and loaded into rail cars for delivery to the Ridley Island port at Prince Rupert, British Columbia. All coal is sold to the Japanese steel industry under a long term contract. The coal seams mined at Quintette are contained in the Lower Cretaceous Gates Formation. Mineable seam thicknesses vary from 0.6 m to 10 m. The regional structure of the area is typical of foreland fold and thrust belts, with open to tight folds and imbricate thrust faulting. The range of structural features found in the three pits, and their effect on mining, forms the subject of this paper.

Jan 1, 1991

By Brian E. McGee

The Federal Coal Management Program represents the culmination of several years of effort by the Department of the Interior (001) to reformulate the manner in which coal owned by the United States is leased and developed. These efforts began in 1970 with a study by the Bureau of Land Management (BLM), which indicated that unless drastic changes were made in. the federal coal leasing procedures, federal coal lands would be leased almost for the asking while production of coal from those lands had been decreasing. Consequently, informal action was taken in 1971, which resulted in no further leasing being authorized until February, 1973. At that time, a formal moratorium on most coal leasing was established, with exceptions granted only for leases needed to satisfy short-term needs such as maintaining existing mines or supplying reserves for new contracts in the immediate future. This leasing policy embodied a long term objective of developing an entirely new planning system for federal coal leasing, as well as to schedule the preparation of a programmatic impact statement for this new system. As a result of the 1973 moratorium and the ensuing application of short-term criteria, only 10 federal coal leases (covering approximately 30,177 acres) were issued from February, 1973, through January l, 1976.

Jan 1, 1982

By Tom Learmont

The importance of coal in solving our energy problems has been widely discussed; the world demand for food requires increased fertilizer production and the minerals to produce fertilizer must be mined. We have seen an explosive increase in the demand for large stripping equipment. It is appropriate that we review this equipment and determine what can be done to improve productivity. While we have used coal mining as an example in the study, much of the discussion will apply equally to other forms of stripping.

Jan 1, 1975

By F. E. du Plessis, P. De Waal

Through the development of innovative in-line mineral quantification sensors, the possibility has arisen to apply modern control theory to implement automatic process control for electrostatic high tension (“HT”) roll separators. A pilot-scale set-up was constructed to enable continuous tests to be carried out. A typical dry mill feed was continuously pre-heated and separated with a modern lab scale HT roll machine. The mineralogy as well as mass-flow of the non-conductor stream was quantified in-line, and the combined streams were re-circulated in an endless loop by a combination of vibration feeders and a bucket elevator. A fractional factorial experiment was executed to determine the most significant control parameters of the HT roll separator. Then a multi-input, multi-output dynamic model of the HT electrostatic separator was extracted by the application of standard system identification techniques for automatic control. The most important control variable to ensure a stable product grade could be identified. This allowed a robust single-input, single-output controller to be implemented. The process variable and set-point was mineral grade and the control variable was electrode voltage. Roll speed was manually adjusted while the mineral grade was kept on set-point by the control system. The roll speed, where maximum mass flow and therefore maximum yield was produced on-grade, could therefore be rapidly determined. Atmosphere humidity and ore temperature served as disturbances. Some other adjustable parameters were kept constant during the experiments, namely feed mineralogy, splitter settings and feed rate. Delivery of maximum yield, with a controlled grade, can improve production while reducing the burden of complex manual tuning. Manual tuning previously involved coping with multiple parameters with uncertain cross coupling influences on the end result. Even the end result was typically only known after completion of mineral assays. Automatic grade stabilisation and yield optimisation for a HT roll separator bank requires in-line measurement of mineralogy and mass flow, as well as the implementation of a robust process control system.

Jan 1, 2005

By M. Akser, M. Tomas

Six Sigma is a methodology that uses a structured and disciplined approach to improve process performance (higher throughput, better recovery, lower cost, shorter cycle time, etc.). Specially trained people called “black belts” lead and manage Six Sigma projects. Black belts, with assistance from their team, ensure that projects follow the DMAIC (define, measure, analyze, implement and control) process phases. Timely completion of each project, with measurable deliverables, is key to Six Sigma’s significant financial success. Implementation of Six Sigma has been growing in recent years in a wide range of industries. The heavy mineral industry, like many other industries, could benefit from what Six Sigma has to offer. Specific Six Sigma project examples are included from DuPont’s Heavy Mineral Production Plant in Florida.

Jan 1, 2005

By William R. Oakley

In order to best-discuss the met spar industry let me take the liberty to review our involvement, that is, my company&apos;s. Our organization has been involved in the fluorspar industry for approximately thirty-five years. We started our activity in Western Kentucky as a mining company and a beneficiator of spar, that is, grinding and grading. After a few short years, the mine became contaminated and rather than invest in a flotation plant, the property was sold and our spar activity was moved, primarily to Mexico. It was decided not to establish ourselves as a Mexican corporation, so, it was necessary to take the position of backer-financier of numerous mining operations. We served in this capacity for quite some time. We also built processing plants on the border in Texas, that is, sizing, grading, etc. in order to market into the steel industry. In 1957, generally speaking, fluorspar for the steel industry was purchased as gravel fluorspar with a maximum of 10% -1/16". The price of this material was $23.50 to $24.00 per ton f.o.b. railcar at the Rio Grande Crossings and about $26.00 or $26.25 f.o.b. barge, Brownsville, Texas. Usually the material was purchased on an effective basis. As you know, 2-1/2 times the silica total, subtracted from the total CaF2 gives the effective calcium fluoride. This was normally the extent of the chemical specifications. Consequently, material was shipped with no regard whatever, to anything other than effective units. The variations in material was absolutely unbelievable. In addition to this, quite frequently, cars were shipped, as they say in the industry, topped. This being, good material placed in the top of cars or barges over bad or low grade. The entire shipment may very well have met the effective unit spec, but the complete imbalance of the sub grade vs. the high grade more or less guaranteed that the consumer was probably using a great deal of low grade and therefore, his usage had to be way higher than it should have been. He came to the conclusion, that because of these conditions and the new technology developing in the steel industry, it was just a matter of time that the entire raw material industry would have to improve. Rather than spend our efforts directed to a substitute flux, we put together a sizing and grading plant in order to ship a controlled crude product, with independent laboratory analysis confirming size and quality. The age of control was started. We began shipping 70 to 72-1/2, 80 and 85 effective with sizing 1/2" by 2", 1" by 3", and 2" by 5" with absolute control on the amount of fines. A material with no fines was a premium product. Incidentally it sold for $24.50 -60 effective up to $28.50, $29.50 for 80 effective.

Jan 1, 1978

By K. E. Harrison

Acid rain legislation as proposed by President Bush [1], if enacted, will immediately refocus current thinking on the economic decision-making as related to coal preparation facilities. Unit operations currently ignored because of their costs, will become mandatory to coal plant designers and operators to ensure maximum energy recovery and sulfur reduction in the entire coal stream. In anticipation of this need, the U.S. Department of Energy, The Ohio Coal Development Office, EPRI and others are sponsoring research in several areas of coal preparation, and coal plant designers are beginning to consider more innovative techniques as they configure their flowsheets for plants of the future. Preparation plants then will have recleaning

Jan 1, 1990

By Raphael Victor

The construction and modification of tunnels brings a requirement for precise measurement of convergence and divergence to safeguard the structure, maintain safety and provide the assurance needed to maintain efficient progress. Established methods include manual measurement using tape extensometers and automated methods using photogrammetry and automated total stations. Drawbacks include the need for frequent access, power supply, cabling, and cost. The paper describes how the development of reliable optical displacement sensors (ODS) has changed the landscape. ODS sensors are connected to a long-range wireless mesh communications network via a solar-powered gateway outside the tunnel, with data instantly transmitted to the internet. A sensor and its reflector target can be installed in 20 minutes and is maintenance free for a decade. Tunnel movement is measured to sub-millimeter precision with repeatability of ±0.15 mm. Integration of a triaxial tilt sensor allows slope distance to be converted to horizontal and vertical changes and allows rotational movement to be determined. Applications include new-build and long-term structural health monitoring. Case studies will be given, including the refurbishment of rail tunnels in Spain where the ODS measured movement during track lowering in a situation where no other automated system was considered viable.

Jun 13, 2023

By Dale K. Nash

The authors have developed a com¬puter-assisted critical path planning and scheduling model to help reduce time required to move longwall mining units. The model includes time constraints and limited resource constraints, such as manpower, machinery, supplies, work space, and transportation routes. Outstanding results were achieved on the first move to which the computer-model pas applied; e.g., downtime due to the move was cut by 50%. The model and the schedules developed using it provide an excellent blueprint for future moves and have led to significant savings in time and costs for Emery Mining Corporation, Huntington, Utah.

Jan 1, 1983

By Michael P. Evans

Traditionally in coal processing jigs have been used to clean the coarse coal fraction, the +3/8" or +1/4" material. Today with the advent of modern fine coal jigs in the United States, its place was moved from the coarse to the inter- mediate coal circuit, the 3/8" x 100 mesh. The most economical coarse coal circuit to build and operate is a heavy media bath circuit. The following table summarizes the cost per raw coal ton processed for a coarse coal jig circuit, and a coarse coal heavy media bath circuit. The flowsheets used to compare these two circuits are shown in Figures 1 and 2.

Jan 1, 1983

By Douglas W. Barr

If some of you have been through the long hot summer in the southwest, you may find it refreshing to turn your thoughts to the wintertime problems of mineral processing in the northern climates. The purpose of this paper is to point out some of the ways in which heat is gained or lost in the tailing basin operation and the problems that can result if too much heat is lost.

Jan 1, 1980

By G. Gaidajis, K. Angelakoglou

The development of a tool for assessing the environmental sustainability of mining facilities is described in this study. The tool is based on the analysis of basic components of the examined system, i.e., the quantities of the incoming materials and outgoing wastes, their hazardousness and scarcity, the utilization of water and energy resources, and the biodiversity. The developed tool provides both qualitative and quantitative assessment of the environmental performance of a mining facility in a broad time scales (past-present-future) and is easily applicable from non environmental experts. Moreover, relative software is developed to further support the application of the methodology. The implementation of the tool is expected to lead to an improved understanding of the environmental performance of a mining facility and more importantly identify the areas of significant environmental concern. However, based on feedback from industries, a number of shortcomings of the approach have been identified so far and are presented, indicating further actions for the advancement of the proposed tool.

Jan 1, 2011