Search Documents

By S. B. Bhagwat

The United States has abundant coal resources that could last at least another century. and probably longer at present consumption rates. Geographically, the coal resources are distributed over the entire nation including Alaska, although there are no coal deposits in the highly populated areas on the two coasts. This allows free access to the coal, but makes transportation more expensive. Not all coals can be utilized equally because they differ vastly in quality. The sulfur content of coals, considered as the most detrimental acid rain-causing element, varies from as low as 0.3 percent in some areas of the western U.S. to 5 percent or more in parts of the Midwest. The chlorine content, which causes corrosion of plant hardware, also varies regionally. The 1990 amendments of the Clean Air Act of 1963 (CAA) require that emissions of sulfur be restricted and rolled back in two stages by the year 2000. There have been a number of reports expressing concern about the future of the industry in the states where high sulfur coal is produced. The remedies devised by the federal government and many coal-producing states in the past to "se-cure" the future of the regional coal industries have focused on the physical task of removing sulfur rather than the economic challenge of doing so at a cost that will enable high-sulfur coals to survive and compete. The past remedies, generally, were not specific enough to account for the characteristics of regional coal deposits and did not look at the coal market as an integrated national and international entity. The State of Illinois has, in recent years, taken a more comprehensive approach to the solution of the problem.

Jan 1, 1992

By J. A. Domenico

A safe and precise mineral separation alternative to heavy liquids is being used for mineral sands exploration on large scale orebodies. The separation process, Magstream®, uses ferro-fluids and magnetic and centrifugal forces to produce precise split points over a range of specific gravities from 1.5 to 18.0 g/cc. This paper describes a commercial scale exploration program treating, roughly, 90 samples per day in Senegal (West Africa). Separation results comparing Magstream® and conventional heavy-liquid separation are presented.

Jan 1, 1994

By James Wm. White

Calculation of consistent steady-state mass balances in operating metallurgical plants and pilot plants is of interest for many reasons. In general, enough data can - and should - be collected to overdefine the system, i.e., permit calculation of nonmeasured quantities via more than one path. In such cases, resulting steady-state metallurgical mass balances rarely close due to sampling, analysis and/ or instrument error. Indeed, determination of a valid calculational sequence for complicated process flowsheets with multiple recycle streams can prove quite difficult. Here we present and discuss a method that has proven useful in analysis of numerous grinding circuit flowsheets of varying-degrees of complexity our technique requires only a consistent process flowsheet with appropriate associated data and arbitrary numbering of streams and equipments. Process topology and user data are decoded to yield a set of "search" or base variables and a set of "calculated" variables in solids, water, particle size and splitter parameter space. This procedure greatly speeds subsequent actual mass balance adjustment calculations since perturing certain variables (e.g., a solids value) does not require recalculation of other variables (e.g., the water balance). Finally, internal search and calculated variables are back converted to User units and used in a Sum-of-Squares criterion. Global minimization of this performance functional then yields a consistent mass balance in a least, squares sense. Weighting factors of choice can be used. Examples illustrate application of these methods.

Jan 1, 1979

By W. Irwin

Global warming hitherto viewed as a distant threat to the environment, is now the subject of fierce goo-political debate. The debate centres around the time frame required to achieve environmental compliance, and the cost implications of meeting that objective. Since coal is the fuel of choice for power generation, the priority objective of energy producers is the pursuit of environmental protection measures that allow coal to be burned without any attendant negative impact on the environment. From an environmental point of view, public attention is today firmly focused on the impact that all industrial activity has on the environment, and coal is singled out from other fossil fuels as being the product of an inefficient smokestack industry. Despite coal's poor public image it is unrealistic to suggest as some do, that use of this fossil fuel as a primary energy source should be drastically curtailed. Coal which already generates about 35% of the world's electricity is continuing to increase its share of this rapidly expanding market, and to argue against its use is flying in the face of reality. However, changes are required in the way coal is used in some of the new clean coal technologies, since many include advanced methods of combustion. Indeed changes in the way coal is used is a vital link to the future of coal as a primary source of energy, and increased coal utilization will be directly linked to changes in its use. Discussion of various issues that affect coal utilization are the focus of this paper.

Jan 1, 1998

By Steve Kral

The third edition of the Underground Construction Association of SME?s (UCA) Cut-ting Edge series of conferences focused on a challenge every underground construction and tunneling project faces: controlling ground water. The conference, held in New York City in November, is a partnership between the UCA and The North American Tunneling Journal. It featured more than 20 technical presentations by professionals from around the world. Each described specific challenges unique to their projects and the solutions employed. More than 175 professionals attended the two-day conference that included an exhibition featuring 17 companies. In addition to the technical program, the Cutting Edge conference featured a site visit to the $10.4 billion East Side Access Project. Sponsors of the meeting included Soil Freeze, Traylor Bros., Kiewit, Skanska, Moretrench, Aecom and The Robbins Co.

By A. J. S. Spearing, T. Kostecki, D. Benton

The use of paste backfill in room-and-pillar coal mines in the United States needs to be fully investigated. This paper discusses a series of physical tests that were conducted to examine the support benefits of theoretical paste backfill regimens in Illinois Basin room-and-pillar coal mines, which necessarily included consideration of weak floor conditions. The series of tests included those simulating strong floor conditions, weak floor conditions, under-confined scenarios, and testing of actual coal-based paste backfill samples. The testing indicated that a paste backfill regimen utilizing a minimum backfill strength of 22 psi at a minimum fill height of 50% of pillar height could significantly increase the longterm stability of coal pillars in the Illinois Basin. Considering typical coal wash plant recoveries, 50% fill would be feasible.

Jan 1, 2014

Federal Regulations require that coal producers conduct a written, in-house investigation with every lost time injury accident. Besides their obvious value in accident prevention, competently conducted investigations can provide a number of additional benefits to include positive supervisor involvement, the control of rising worker's compensation costs and a measure of protection from civil/criminal proceedings. The paper describes such topics as MSHA minimum requirements, investigator selection and training, accident site procedures, witness interview techniques and the management review process. The reader is also presented with a number of information resources available through MSHA, the National Safety Council and other sources.

Jan 1, 1995

By C. M. Brown

Common operating philosophies and objectives of mining and mineral process operations are discussed. Key information required to effectively monitor operations is reviewed in conjunction with the impact of external variables such as commodity price changes on strategies adopted.

Jan 1, 1991

By Felicia F. Peng

The plant data were collected from three streams around a dense medium drum for coarse coal cleaning operated at various volumetric ratio of medium-to-feed. The effect of the volumetric ratio of medium-to-feed (MF) and particle sizes on the performance criteria, g50 and Ep, of the dense medium drum. These measured data were adjusted and calculated for the yields and balanced relative density distributions by mass balanced method based on the statistic principle. These balanced data were then used to formulate the mathematical models of the separation distribution curves for the various feed size intervals. The correlation equations for the g50 and Ep as the function of inverse of the feed size, and MF and total throughput were established. A numerical algorithm utilizing the Secant method, based on the root searching principle, was developed for yield optimization and simulation of dense medium drum separation to improve the separation efficiency and hence the product yield. The relationships between the direct ash content and relative density of the particles in feed and the products were established and incorporated into the numerical algorithm for predicting the product quality.

Jan 1, 1996

By R. G. Johnston

Minerals have many uses in paint systems. These roles include use as primary and extender pigments, sheen control, film durability enhancement, and rheology control. These and other uses of minerals in paints, and the effects of mineral quality variations on coatings performance are discussed. As coatings performance requirements become more demanding, tighter consistency of important mineral properties, such as particle size distribution and purity, is becoming increasingly vital. Future directions of mineral use to meet projected environmental restrictions and performance demands on coatings, including the use of advanced minerals technologies, are examined.

Jan 1, 1993

By C. E. Seaman, H. Jiang, S. Klima, T. W. Beck, Y. Zheng

Respirable coal dust has been long recognized as a leading cause of multiple lung diseases. Efforts aimed at reducing dust concentration in underground mines have been made, but increases in coal workers’ pneumoconiosis incidence rates over the last 20 years among U.S. miners are concerning. Dust deposition and water spray suppression are two types of dust removal mechanisms in underground mining activities. In this study, laboratory tests were conducted to investigate the respirable dust decay characteristics during deposition and suppression processes in a confined dust chamber. Dust concentration and size distribution were monitored continuously throughout each 60-minute test. A number-basis particle size distribution was used for analysis to capture the changes of smaller size fractions within the investigated dust sample. This study found that around 62.1% of respirable dust particles were deposited at the end of the deposition test. In addition, the final deposition rate for very fine particles can be less than 20%. The results from the suppression test indicate that larger particles were removed quickly; however, sub-micron particles remain suspended through the 60- minute water spray, and particles under 0.5 µm can be considered irremovable dust under single-spray operation conditions. This study also observed the resuspension of a significant amount of sub-micron particles by the water spray. The results of this study provide basic information for improving dust control strategies and can be utilized to improve the water spray performance for reducing airborne dust levels.

Mar 2, 2022

By W. B. Greer

The performance of seals in boreholes, shafts, and tunnels is an important concern in mine safety, in the control of effluents from operating and abandoned mines, and in the underground containment of hazardous wastes (Einarson and Abel, 1990; Mining Waste Study, 1988). Despite the clear need for effective seals, few documented test results are available concerning the performance of in-situ seals. Some evidence indicates that horizontal or near-horizontal holes are especially difficult to seal properly (Kelsall and others, 1982). This research involved the installation, extensive hydraulic testing, removal, and post-test examination of a l0-cm-long by 10-cm-diameter cement grout seal in a near-horizontal borehole in limestone. The work was performed in an underground mine on Marble peak in the Santa Catalina Mountains, Arizona. A test hole was diamond cored in the re-crystallized limestone of the Escabrosa formation. The hole is 33.24 m long, 10 cm in diameter, and dips at 10.4 degrees. The hole extends between two drifts and thus is accessible from both ends.

Jan 1, 1992

By Winn B. Frank

Events of the mid-1970's have materially affected US coal production and transportation by railroad. Coal, as a replacement or substitute for petroleum fuels, has been hauled in significantly increased tonnages. Concurrent with the new demand, the railroad regulatory environment has undergone major changes, especially in "deregulation" activity. Those two events have produced considerable Litigation regarding coal rates. This paper discusses the factors involved with railroad rates and topics such as revenue adequacy, Ramsey Pricing, stand-alone cost, and differential pricing. In addition, an update on the western railroad merger situation and the implications for coal transportation are presented. The paper concludes with an evaluation of the current regulatory climate and future prospects.

Jan 1, 1983

The United States is being invaded... by foreign capital: marks, francs, pounds, yen, lire, riyals, you name it: On almost any given day the Wall Street Journal will contain a new report on a department store, newspaper, bank, hotel, agricultural land, supermarket chain, et a1 being bought into by overseas investment. Xenophobic reaction to this revised national condition has begun to set in. Several farming states have and are introducing legislation to monitor foreign land buying. In Congress a mandatory reporting requirement for foreign purchasing is currently under study. In a relatively short period the country has reverted from world leader- ship in overseas acquisition and involvement to become itself one of the prime investment opportunities in existence. Interestingly enough, one of the industries where this changed status has become most apparent and pronounced is within that small/regional/segmented/low value-to-weight bulk commodity enterprise ranked as the backbone of the nation's construction activity. U.S. cement making is not only undergoing internationalization in its ownership, but also in its product, equipment, and engineering expertise.

Jan 1, 1979

By Daniel Maine

Swelling clay soils have been problematic to many types of infrastructure in the United States. However, their impact on underground construction is often misunderstood. The use of swell pressures in design of initial tunnel and shaft support lacks proper guidance and is often mis-interpreted. This paper provides insight and guidance on how to implement a geotechnical investigation program to determine if swelling soil exists at a site and how it impacts the design of temporary support systems for underground projects. An example is provided for how swell pressures were incorporated into the design of an initial support system for a rib and lagging tunnel system and problems that occurred.

Jun 23, 2024

By M. Scaggs

"Respirable dust in underground coal mines has long been associated with lung diseases, and regular dust sampling is required for assessing occupational exposures. At present, respirable dust concentration and crystalline silica content are commonly determined, but considering recent and yet unexplained increases in the incidence of lung disease amongst miners in specific geographic regions, more information about specific dust characteristics is urgently needed. While particle-level dust analysis is ideal, it is impractical for large numbers of dust samples because it is both time and cost intensive. Thermogravimetric analysis (TGA), however, is an alternative option, which offers the ability to determine the total coal to mineral mass ratio in a dust sample – analogous to proximate analysis of bulk coal samples for determining ash content. Here, preliminary development of a TGA method for this purpose is presented. The method is being developed to evaluate dust collected on mixed cellulose ester (MCE) filters using approved permissible sampling equipment. INTRODUCTION Based on the particle size, airborne mine dust can be classified in three categories: inhalable dust (< 100 µm in size), thoracic dust (< 25 µm in size), and respirable dust (< 5 µm in size) (Ramani et al., 2003). The World Health Organization (WHO, 1999) defines inhalable dust particles as those which can be breathed into the nose and mouth, and thoracic dust particles as those which can penetrate airways of the head and enter the airways of the lung. On the other hand, respirable dust particles can penetrate beyond the terminal bronchioles into the gas-exchange regions (alveoli) of the lungs (WHO, 1999). Hlavay (1992) reported that the seriousness of the damage in the lungs and respiratory tract is based on amount of dust remaining in these organs, and the amount of dust depends on the extent of dust exposure, the size distribution of the dust particles, and the capability of the body for dust elimination. Inhalation of respirable coal dust by miners can cause a disabling and potentially fatal lung disease which is called coal worker’s pneumoconiosis (CWP). Silicosis is another fatal lung disease caused by inhalation of respirable silica dust. In CWP and silicosis, dust particles deposit in the lungs, damage the lung tissue, and ultimately cause scarring which cannot be reversed (Colinet, 2010). While overall incidence occupation-related lung disease amongst coal miners in the US has been declining for over 40 years, it appears that there has been a recent increase in specific locations in Central Appalachia (CDC, 2006; Pollock et al. 2010; Suarthana et al., 2011). Although this trend is yet unexplained, one theory is that particular dust characteristics in these locations may be a factor (Hassan and Lau; Page & Oraniscak 2002). For example, several studies have indicated that different coals may generate different amounts of respirable dust (e.g., see Page, 1993 and Litton and Page, 1994), and the surrounding geology may also play a role in terms of the types of dust particles generated. Although respirable dust concentration and crystalline silica content are commonly determined as part of regulatory compliance sampling, more information about specific dust characteristics (e.g., size, shape and composition) is urgently needed."

Jan 1, 2015

By R. C. Emmett

The industrial practice of concentration of solids and production of clear solution by gravity sedimentation is an old technology. Through the years, many devices have been designed and built to aid this process. One of the more significant developments was a revolving rake mechanism to convey settled material to a central discharge point of a circular tank, patented in 1907(1). In recent years, clarification systems employing parallel inclined plates have appeared on the market; the original device utilizing this principle was patented in 1886(2). Numerous other methods have been invented, tested, discarded and sometimes re-invented, all with the specific intention of improving the capacity of a particular settling area. Sedimentation theory, as expressed in Stokes&apos; Law, shows that the rate of settling of a particle is directly proportional to the difference in density between the particle and the surrounding liquid and, more significantly, proportional to the square of the particle diameter. Anything that can increase the latter will greatly assist sedimentation and, as a result, flocculation always has been an integral part of sedimentation. Most materials suspended in aqueous media are naturally flocculent to some degree and, hence, are readily concentrated by sedimentation, although sometimes very slowly.

Jan 1, 1978

By Robert Vergie

Like most of you, I would rather work on a job than talk about it. But it is fruitful to spend some time taking stock of important developments in the heavy construction field. One of the strongest recent movements affecting the industry has been the push for safety. I regret that it is a recent development. Not that builders were against safety. Too often though, it was easier to continue with dangerous old work methods than to try something new. Too often, it was easier for equipment manufacturers to build production tools with little consideration for worker safety. And too often, accidents and gruesome disasters occurred. The ultimate result of on-the-job injuries in construction and other industries was the Federal Government&apos;s Occupational Safety and Health Act of 1970. Individual states were required either to accept OSHA or pass updated regulations at least as stringent as the Federal requirements. These new rules must be strictly obeyed -- not just because they carry civil and criminal sanctions -- but because they correct unsafe conditions and reduce hazardous acts. Though some OSHA measures have been criticized as superfluous, most of them do in fact save lives and limbs. Equally important, the tunneler who follows the new safety regulations can be fairly certain of an efficient, uninterrupted operation. Regulations do sometimes bring rewards.

Jan 1, 1974

By Andre Balt, Pierre Hofmeyr

It is only recently that automation has been applied to mining analytical laboratories. This paper describes the use of automation in the laboratory analytical process of hard-rock mining and geological samples and slurries in mining concentrator plant process control laboratories. Types of analysis include fire assay, XRF, ICP and wet chemistry. The benefits of automation are reduced unit cost of analyses, greatly reduced staff requirements, higher quality of data and very fast turn-around times.

Jan 1, 2005

By S. K. Mohanty, T. M. Dittrich, M. J. Allen, M. Dardona, A. C. Strzelecki, J. Hovey, Boukhalfa. H.

Rare earth elements (REEs) have many critical uses in advanced technology and the lack of a reliable domestic supply has been identified by the US DOE as a vulnerability to US economic security. Our research focuses on developing an economical process for extracting REEs from coal fly ash and power plant wastewater sludge by coupling a hydrothermal extraction process with the engineering of a ligand-associated media for concentrating REEs from the extraction liquid. Ash samples have been collected from two Detroit-area Power plants that burn 100% low sulfur coal (Trenton Channel) or fuel blends of 75% low sulfur coal and 25% high sulfur coal or 70% low sulfur coal, 15% high sulfur coal, and 15% petcoek (Monroe Power Plant). Ash samples are then subjected to hydrothermal conditions from 100-350 °C for 1-24 h at Los Alamos National Laboratory and leachate concentrations are measured by inductively coupled plasma-mass spectroscopy (ICP-MS) and compared to hydrofluoric acid digestion results. Experiments designed to aid in ligand selection and loading optimization show that di-(2-ethylhexyl)methanediphosphonic acid (H2DEH or DIPEX™) can be successfully loaded to a commercially available swellable organically modified silica (SOMS) media. Preliminary results show that DIPEX-associated SOMS surface loading can exceed 4x on a mass/mass basis and in simplified sorption experiments with Nd solutions (~pH 2), the DIPEX-SOMS media can sorb >90 mg Nd per g of media. Recovery of the sorbed Nd with low pH solutions has had low efficiency with the high (4 g DIPEX/ g dry media); however, near complete recovery was achieved with lower surface loadings (0.05 g DIPEX/ g dry media). Column experiments are being conducted to evaluate the optimal ligand/media ratio for repeated use. Completive sorption with Fe and other major cations are also being evaluated.

Jan 1, 2019