Search Documents

PolyMet Mining is developing the NorthMet property near Duluth, MN. Laboratory investigations have led to the development of the Platsol process to dissolve in one step the base metals (copper and nickel) as well as the gold and platinum group metals (PGM). To complete the prefeasibility study, a fully integrated, 10-day pilot plant trial was undertaken. The trial consisted of high-temperature (>220ºC or >428ºF) pressure oxidation in the presence of 5 to 10 g/L chloride (the Platsol process). This was followed by solid/liquid separation, gold plus PGM recovery from solution, conventional copper solvent extractions/electrowinning (SX/EW) and recycling of the copper raffinate to the autoclave. The concentrate tested during the trial period was a NorthMet bulk flotation concentrate. It assayed 14.7% Cu, 3.05% Ni, 0.14% Co, 26.7% S, 1.4 g/t (0.041 oz/st) Au, 2.2 g/t (0.064 oz/st) Pt and 9.9 g/t (0.289 oz/st) Pd Laboratory results were confirmed and, with minor adjustments of the laboratory Platsol conditions, the following leach extractions were obtained during the pilot plant trial: 99.6% Cu, 98.9% Ni, 96% Co, 94.6% Pd, 96 % Pt and 89.4 % Au.

Jan 1, 2003

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this study is to assess the impact of different reagents, such as limestone, lime, magnesium oxide, and sodium hydroxide, in experiments carried out in the single purification step and in two consecutive purification steps by raising the pH of a rare earth sulfuric liquor with the aim to remove or reduce the impurity concentrations in the rare earth sulfuric liquor. The choice for the best purification condition was made based on the minimum loss of rare earth elements (REEs), reagent consumption, and residue generation. The exploratory experiments show that it takes place in the two consecutive purification steps, the first one consists in dosing the limestone pulp until it reaches a pH of 3.5 followed by an addition of a lime pulp reaching a pH of 5.0. Under this condition, the results were a total removal of Fe3+, PO4 3− , and Th4+ ions and a reduction of 99%, 87%, and 37% w/w in the Al3+, UO2 2+, and SO4 2− concentrations, respectively, in the purified rare earth liquor. Furthermore, the lowest REE losses (8.3% w/w) and reagent consumption (4.3 kg/m3 ) and also a low residue generation (7.5 kg/m3 ) were observed in this condition. Despite reaching similar results regarding impurity removal, the experiments done with the addition of limestone, lime, magnesium oxide pulps, and sodium hydroxide solution in the single purification step, where the pH was raised to 5.0, presented higher REE losses (64.9%, 42.5%, 44.8%, and 60.9% w/w, respectively) and a higher residue generation (43.2, 25.1, 11.1, and 13.6 kg/m3 , respectively). This occurred due to the co-precipitation of salts containing rare earth elements in their composition. The experiments conducted with limestone, lime, and MgO resulted in a higher consumption of reagents, while the same result was observed when NaOH was used (4.3 kg/m3 ). In the experiments carried out with the addition of magnesium oxide and sodium hydroxide, the respective purified rare earth liquors presented a high concentration of magnesium, sulfate, or sodium, which could impact the quality of the marketable rare earth salts, whereas the salts obtained under the best condition observed in this study seem to be amenable for use as raw material in an attempt to obtain rare earth products with an acceptable chemical quality.

By J. C. Mullen

Today, the coal mining industry is more knowledgeable on the potential negative economic consequences associated with improper management of hazardous substances and various types of solid waste. The practices evaluated during environ-mental audits are discussed and example situations are shared from previous audits of coal mines and analogous situations. The importance of assessing and understanding purchasing, warehousing, safety, maintenance, electrical, operations, and environmental management practices and procedures is highlighted as a key to a successful and practical program. A waste minimization approach is presented including strategies for screening product purchases, product substitutions, and testing and record keeping.

Jan 1, 1992

By MAURICE SUNKPAL, Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Despite numerous empirical, numerical, and hybrid studies conducted on the subject of coal rib failure, mine fatalities related to rib failures continue to occur at around 1.5 per year between 2009 and 2021. To date, a standard methodology for the design of coal rib supports that can accommodate the wide range of unique conditions found in coal mines in the USA has not been developed, forcing mine operators to rely on the trial-and-error process or industrial legacy practices for the design of coal rib support patterns. In this study, to better understand the support systems’ effectiveness, various rib bolting scenarios were investigated. A coal mass constitutive model is implemented to a distinct element method (DEM) code, and rib factor-of-safety (RibFOS) analyses were performed by applying strength-reduction for the coal matrix and explicitly modeled face cleats. Ribs with various overburden depths and mining heights composed of solid Banded-Bright coal (BBC) were considered in this study. Different scenarios such as rib bolt length and the number of bolts were studied to quantify the effect of primary rib support density on rib stability. As a result of the unsupported coal rib analyses, a decaying exponential relationship is proposed between the mining height-overburden depth and the RibFOS. The developed coal rib models clearly show the coal-rib bolt interaction and illustrate how the addition of rib bolts restricts the movement of the coal rib. The results reveal that the strength reduction method in DEM code with the coal-mass model can aid in the development of practical primary support charts, which can help in the rib support design process. In addition, an unsupported RibFOS cutoff is proposed, beyond which the addition of primary support cannot stabilize the failed rib structure.

Aug 5, 2023

By J. A. Organiscak

Longwall mining technological improvements have provided significant increases in productivity over the last 15 years. Longwall productivity is anticipated to continue to escalate with expanded application of automated equipment. Automation technology that will likely be adopted over the next 5 years is memory cut with shearer initiation of shield movement supervised by a couple of face workers. Operations using this technology will most likely relocate many production workers from the face to the outby gate entries and position several face workers outby the shearer, exposing workers to different health and safety risks. These changing risks are primarily related to worker relocation and expected increased production levels. Workers outby the face will most likely have less dust and noise exposure, but will be exposed to other safety hazards associated with outby equipment movement, materials handling, and gate entry ground movements. The face workers will most likely be exposed to higher respirable dust and noise levels generated by the equipment at elevated production rates. Methane gas emission is also expected to increase with faster mining rates. These operational changes and the control technologies needed to reduce redefined longwall worker hazards at semiautonomous longwall operations require examination to maintain the health and safety of mine workers.

Jan 1, 1996

By S. K. Kawatra, K. A. O, DeLa&apos

On-line sensors and process controls are important for efficient operation of coal preparation plants. The objective of this paper is to describe the current practice in on-line measurement of composition, density, moisture, level, flow and weight. This paper also discusses how on-line sensors can be implemented in process control, and how sensors which are currently being developed can be utilized.

Jan 1, 1988

By S. C. Howell

The mining of taconite, to provide feed for a processing plant, requires that the flow of material continue uninterrupted. This means first, that the crude must be of a size acceptable to the primary crusher in order to reduce the delays caused by plugging the crusher with chunks. Secondly, elimination of oversize in the pit will reduce costs of all wear parts used in the mining and processing of taconite. Savings in wear parts is readily recognized in dipper teeth, bases, buckets, truck boxes, and crusher parts, both primary and secondary. During the early days of taconite mining, it was soon recognized at reserve mining company's Babbitt operations that experience in mining other ores was not always (or ?necessarily??) Applicable to excavating taconite. This was especially true in drilling and blasting. Blasting of small tonnages in single or double rows simply filled the pit with scattered chunks and provided very shallow banks for shovel loading. It also created problems for the jet piercers, since all drilling had to be performed in fractured areas. Drilling efficiency suffered and costs were extremely high. Shovel and truck efficiencies were also low and again costs were high. A high percentage of secondary breakage was required. This necessitated the use of numerous man hours to jackhammer holes in chunks, preparatory to loading and blasting. After the chunks were reduced, bull- dozer and grader hours were needed to pile the taconite for acceptable shovel loading.

Jan 1, 1968

By J. Navoyski, B. Macdonald, W. J. Helfrich, J. L. Bellanca, B. Demich

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of company names or products does not constitute endorsement by NIOSH. ABSTRACT The pervasiveness of high-fidelity video games raises expectations of quality, detail, and lighting in virtual reality (VR) applications. However, high-quality models of mining equipment and environments are often not readily available, and developers may not be familiar with the latest techniques, such as physically based rendering (PBR). Because a consistent aesthetic is critical for maintaining immersion and controlling visual stimuli in research as well as in training, researchers at the National Institute for Occupational Safety and Health (NIOSH) created an asset development workflow. This paper details this workflow, including precision modeling and PBR techniques as well as a rigorous review process. It also describes lessons learned in the creation of photorealistic VR assets. BACKGROUND Virtual reality (VR) describes the simulated experience generated by an assemblage of hardware and software that are used to immerse the user. Over many years VR developers targeted the development of virtual environments (VE) toward various purposes: entertainment, the treatment of phobias [1], rehabilitation [2], and training [3]. A large part of the VE development includes digital assets, where digital assets refer to the non-programmed elements including 3D models, audio, and user interface. Because vision provides nearly 10Mbps of data [4] and accounts for the majority of all sensory input combined [5], a focused effort on asset appearance in VEs is warranted. Furthermore, research has shown that higher-resolution imagery increases search performance and training transfer, necessitating high-fidelity assets [6, 7]. In addition to being visually appealing, it is important that the assets and environment are also dimensionally accurate and consistent in order to elicit appropriate responses from the end users as they interact with and among these items [8, 9]. Researchers at the National Institute for Occupational Safety and Health (NIOSH) have developed VEs and digital assets under several research projects over the course of the last two decades [10, 11, 12, 13]. This work has provided researchers with a strong knowledge base for digital asset development. However, the assets themselves have had limited reuse value. Due to the extended timeframes and limited scope of these projects, the previously developed assets are not consistent in visual quality and dimensional accuracy. Moving forward, researchers wanted to minimize future development time and use of resources as well as adopt new asset development tools and game engine technology. Therefore, the aim of this paper is to document a new asset development workflow including geometry, materials, UV layout, and shader implementation combined with review steps in order to produce high-fidelity simulation assets that are accurate with consistent characteristics, using repeatable methodologies that are well documented.

Jan 1, 2019

By S. E. Younis

The mining industry is currently looking to better understand, anticipate, and be able to mitigate business and operational risks in order to deliver the rewards of risk taking, and to minimize the frequency and impact of risk on the downside. Assessing risk works from the premise that the identification and management of existing risks can be very challenging, especially when threats are not easy to detect, the likelihood of occurrence is difficult to gauge, and/or the consequences are uncertain. Some approach this as a ?check the box? task, even though fire and safety incidents continue to occur and investigations often find the hazard analyses did not properly identify the cause or consequence. You cannot engineer protective designs and safeguards for causes and consequences that have not been identified appropriately. For the mining industry, risk management is an important tool for making critical decisions and, in some cases, meeting regulatory requirements. Providing high-quality documentation that meets both regulatory and corporate requirements is critical for maintaining safe, uninterrupted mining operations. Risk management is a five-part process: 1. Identify the hazards and their causes, 2. Determine the hazard consequences, 3. Calculate the frequency of occurrence, 4. Quantify the risk associated with the system, process, or procedure, and 5. Provide feasible solutions for the risks

Jan 1, 2012

By Richard E. Hucko

The Coal Preparation Division of the Pittsburgh Mining Technology Center conducted an investigation to assess and compare the pyritic sulfur reduction potential of coal-pyrite flotation and high-gradient magnetic separation (HGMS). Tests were run on three coals--an Upper Freeport bed coal, a Lower Kittanning bed coal, and a Pittsburgh bed coal--to establish grade- recovery relationships characteristic of both processes. Representative portions of each coal sample were crushed to two top sizes--nominal minus 35 mesh (0.5 mm) and nominal minus 100 mesh (0.149 mm)--and subjected to conventional froth flotation. The froth product was then beneficiated by coal-pyrite flotation or HCMS to provide a direct technical comparison of the two processes. At minus 35 mesh (0.5 mm), the size normally employed for coal flotation, both coal-pyrite flotation and HGMS effectively separated pyrite from coal, and the performance of the two processes was essentially the same. At a size of minus 100 mesh (0.149 mm) , however, the performance of HGMS exceeded that of coal- pyrite flotation. The separations effected by HGMS were more efficient at minus 100 mesh (0.149 mm) than at minus 35 mesh (0.5 mm). On the other hand, it was concluded that either the effectiveness of coal-pyrite flotation decreases with diminishing top size, or the process has not been optimized to treat material finer than 35 mesh (0.5 mm).

Jan 1, 1981

By S. M. Bulatovic

The western industrial world has to rely more and more on complex polymetallic sulphide ores as sources for base metals. These ores are composed of fine grained sulphide minerals such as chalcopyrite, galena, sphalerite, pyrite, pyrrhotite and marcasite. The liberation sizes of the individual minerals can range between 30 um and 5 um. Therefore, applying conventional techniques to recover these finely disseminated minerals usually results in unsatisfactory metallurgical performances with high losses of the valuable mineral to the slime , fraction of the tailing. New concepts for treating these polymetallic complex ores are discussed in this paper. Beneficiation techniques utilizing new reagents and a new approach to pulp preparation are described. Some of these techniques were applied to ores from existing concentrators as well as to new ores. The results of these studies are discussed in the following sections.

Jan 1, 1990

By A. Anani

The goal of hot mix asphalt (HMA) design is optimal material blending to meet Superpave specifications. HMA cost minimization has being modeled as linear programing (LP) (Awuah-Offei et al 2011) and mixed integer LP problems (Brown et al, 2012) and solved with commercial software such as LINDO and CPLEX. Often these software, which are designed to solve general optimization problems, have licenses that cost thousands of dollars. The objective of this study is to develop a novel solution algorithm to the HMA optimization problem presented by Brown et al. (2012), which will negate the need for expensive commercial packages and is specific to this problem. This novel algorithm is based on the branch and bound algorithm for solving mixed integer problems. The algorithm is incorporated into a software package with an easy-to-use graphical user interface. The developed algorithm is validated using a real-life HMA problem. Using this solution algorithm will save companies thousands of dollars, otherwise used to purchase software licenses.

Feb 23, 2014

By Joseph D. D?Annunzio

The report on cut and cover construction as assembled by the Organization for Economic Co-operation and Development covered 17 different countries based on a total of just under 400 individual replies of which about 30% of the replies were from the United States. In general, the review of replies to the questionnaire led to the impression that cut and cover construction is a very inadequate method which needed many improvements. This unfavorable judgment, however, resulted in the manner in which questions were asked rather than in the method itself, It can be concluded that the cut and cover construction method has proved itself as an excellent method and that it has reached a high degree of technological perfection, but inadequacies stilt exist, and for purposes of complete evaluation, comparisons with mining tunnelling methods should be carried out. The principal problem in cut and cover construction is the interaction during construction between the construction process and the existing use of the surface and subsurface environment. The greatest impediments to cut and cover construction have little to do with the physical works being constructed, but more with creating a site in which the work can be performed. Utility relocation, traffice maintenance, and protection of existing structures are major problems for the construction contractor, and too frequently receive insufficient attention in preconstruction planning and design. Some OF the areas in which research should be undertaken are as follows:

Jan 1, 1970

By C. Pace, D. Darlington, A. Montera, C. Lingren

"A phosphate beneficiation plant in Utah is using isotope-based Prompt Gamma Neutron Activation Analysis (PGNAA) technology to analyze the entire slurry streams of the incoming feed and final product in order to adjust the flotation circuits in near real time and optimize the plant output. The plant has gained greatly improved visibility/control and has reduced product variability for improved profitability and product quality. This paper takes a look at the economics as well as application details and the difference this technology provides in a phosphate application. SIMPLOT PHOSPHATES INTRODUCTION Simplot’s Vernal, Utah Phosphate Mine and Mill are located in the northeast corner of the state in the Uinta Mountains along US Highway 191, eleven miles north of the town of Vernal. The phosphoric acid and fertilizer plant fed by the Vernal mine is located 94 miles Northeast of Simplot Phosphates in Rock Springs, WY.At the Vernal plant, loader and shovel mining to 85 Ton capacity trucks is done at an annual rate of 3.8 Million tons of ore. Run of mine ore is crushed in a mineral sizer to minus 14 inch diameter at the rate 11,500 tons a day and transported to the SAG Mill’s 130,000 ton surge stockpile by overland belt. ORE RESERVES The ore is a Phosphoria Formation of sedimentary rock type dating to the Permian Age. The ore body rests over a 25 mile area on Weber Sandstone from the Pennsylvania and Permian geologic period. Layers of Phosphate Rock can vary in thickness from 0.3 up to 2.1 feet, alternating with layers of Mudstone. The eastern edge of the ore’s body Panel “G” runs 16 feet deep with a feed grade of 21.5% P205 with lower MgO diluents of less than 2.79%."

Jan 1, 2016

By D. K. Marjaniemi

The U.S. Bureau of Mines inventoried and characterized mineral sites and production plants within 200 km of the border in both the U.S. and Mexico. Sources of information included the USBM Minerals Availability System, the USBM Automated Mineral Information System, the USGS Mineral Resources Data System, the Mine Safety and Health Administration Address/Employment File, and the literature. Three hundred seventy-eight major construction material and industrial mineral properties were identified and characterized in the U.S. and Mexican parts of the Borderlands. Sixty-six major metallic mineral properties were identified and characterized in the Mexican part of the Borderlands.

Jan 1, 1996

By R. Buisman, K. Reyneke, M. Fullam, J. V. Brown

Most mineral processes currently in use, such as flotation, spirals, gravity concentrators, etc., are only effective over a small range of sizes, hence the upstream need for technology to accurately classify fines by size. The Pansep’s design is revolutionary. Slurry is fed onto connected mesh sections that move without bending or vibration, in a circular motion. Both sides of the screen mesh are utilized, so Panseps are self-cleaning and has half the footprint of other mesh-type screens. Developed in South Africa in 1997, the Pansep has proved itself very effective as a wet fines screen to effectively classify fine mineral fractions from 50 to 2,000 micron (325 to 10 mesh).

Jan 1, 2001

By W. R. Penney, J. M. Richardson, J. Y. Oldshue

Introduction The mining industry has for years underrated the value of mixing in mineral processing unit operations. In present-day operations where leaching is playing an ever increasing role in the total profit picture, the need for good mixing is becoming more obvious. The engineer in the research laboratory and in the operations is by necessity becoming more familiar with the concepts of mixing. This section is designed to provide the engineer with mixing data and correlations sufficient to assist in the general planning of simple mixing systems.

Jan 1, 1985

By R. H. King

This paper describes the results of an underground coal mine trial installation of a shielded trailing cable. The cable was a three conductor, round, type SHC-GC, and was installed on a shuttle car in a conventional room and pillar mining section. The purpose of presenting the information is to prepare mine operators for proposed legislation that will require shielding on low-voltage trailing cables. Specifically, machine modifications are required to cable reels, packing glands, and couplers. Cable splicing is not as complex as expected but additional materials are needed in the kit and splice training is necessary. Even though shielding will cause some problems for the mine operator, it can reduce the hazard of electrical shock to mine workers. This paper will present information that mine operators can use to solve most of the problems that will be encountered if they are required to install shielded cables. The in-mine evaluation was funded by the U.S. Bureau of Mines.

Jan 1, 1980

By Shangyong Lin, Wei Sun, Weiping Liu, Muhammad Azam, Junfeng Chen, Yujie Zhao, David Asubonteng, Michael Ngoie

Copper concentrates are widely used in smelting operations worldwide and typically consist of chalcopyrite ( CuFeS2) as the primary mineral, with chalcocite ( Cu2S) and bornite ( Cu5FeS4) as secondary copper-bearing minerals. However, these concentrates often contain hazardous impurities, such as the fluorine ion, which can result in various complications during the smelting process. These issues include equipment corrosion, gas treatment requirements, environmental hazards, and strained community relations. Furthermore, high fluorine content in copper concentrates can lead to penalties and limitations during sales. To address these challenges, this comprehensive review assesses current techniques for removing fluorine from copper concentrate. Drawing upon recent research and the findings in the field, the review analyzes the advantages and disadvantages of existing fluorine removal methods and identifies critical issues requiring attention in the future. This review provides valuable insights into the current state of fluorine removal from copper concentrates and serves as a practical guide for researchers and industry professionals in this field.

Aug 2, 2023

By E. Hasanbas

Vibrating screens and crushers are the workhorses of material sizing. Unfortunately their natural frequency is often in the range of typical supporting structures, thereby making installations prone to vibration problems. Much of the available literature regarding the support of vibrating screens is fairly confusing and outdated. This paper presents the results of utilizing accelerometers and finite element software in the analysis and design of supports for vibrating equipment. It contains data from field studies of vibrating screen and crusher installations, design of new and repair of existing supporting structures, and the correlation between field data and finite element time history analyses. Finally, the paper summarizes a method for analyzing and designing structures subjected to vibratory loads and predicting their behavior.

Feb 23, 2014