Search Documents

By G. Konstantopoulou

Environmental degradation due to abandoned quarries is an international problem, more intense when these sites are found in urban or suburban zones, in environmentally sensitive areas or are visible from sites of special interest. Rehabilitation solutions applied worldwide, range from simple relief restoration and planting to more sophisticated site exploitation in order to serve specific social needs. The elaboration of rational rehabilitation plans for every site presupposes deep knowledge and comparative evaluation of all the parameters of the problem. In this paper, a methodological approach of rehabilitation solutions for abandoned quarry sites is elaborated, based on domestic and international experience and practice. Solutions are grouped in eight main categories. In every category the framework of prerequisites and confinements (environmental, technical, social, economic, legal) for their application in Greek quarry site is investigated. A comparative assessment of alternative restoration solutions is introduced, using tools supplied by environmental economics, cost-benefit analysis, G.I.S. and multi-criteria analysis and follows in two stages: 1) Establishment of a set of criteria aiming at a priority list for a number of quarry sites located in a geographical or administrative district. 2) Assessment of alternative solutions for every single quarry from the previous priority list for the selection of the most adequate using technical, economical, social and environmental criteria.

Jan 1, 2008

By S. E. Vanderslice, J. A. Hummer

"The results of laboratory evaluations were used to compare the potential of two alternative, biomass-derived fuels as a control strategy to reduce the exposure of underground miners to aerosols and gases emitted by diesel-powered equipment. The effects of fatty acid methyl ester (FAME) biodiesel and hydrotreated vegetable oil renewable diesel (HVORD) on criteria aerosol and gaseous emissions from an older-technology, naturally aspirated, mechanically controlled engine equipped with a diesel oxidation catalytic converter were compared with those of widely used petroleum-derived, ultralow-sulfur diesels (ULSDs). The emissions were characterized for four selected steady-state conditions. When fueled with FAME biodiesel and HVORD, the engine emitted less aerosols by total particulate mass, total carbon mass, elemental carbon mass and total number than when it was fueled with ULSDs. Compared with ULSDs, FAME biodiesel and HVORD produced aerosols that were characterized by single modal distributions, smaller count median diameters, and lower total and peak concentrations. For the majority of test cases, FAME biodiesel and HVORD favorably affected nitric oxide (NO) and adversely affected nitrogen dioxide (NO2) generation. Therefore, the use of these alternative fuels appears to be a viable tool for the underground mining industry to address the issues related to emissions from diesel engines, and to transition toward more universal solutions provided by advanced engines with integrated exhaust aftertreatment technologies. IntroductionDiesel engines have been the workhorses of modern society for industrial and transportation enterprises. Diesel engines of all generations are extensively used in a variety of light-, medium- and heavy-duty applications in underground mining operations around the world. Fuels obtained from various sources and with wide-ranging chemistries have been combusted in diesel engines. However, the bulk of the currently used fuel can still be traced to nonrenewable petroleum sources. The petroleum-derived diesel fuels are primarily made up of saturated acyclic hydrocarbons (parafins or alkanes), aromatic hydrocarbons (arenes or aryl hydrocarbon), and unsaturated hydrocarbons with double bonds (olefins and alkenes). Improvements in the quality of petroleum-based diesel fuels was identified in federal regulations as an important piece in resolving the puzzle of diesel engine emissions (Environmental Protection Agency, 2001, 2004). The reduction of U.S. diesel fuel sulfur content below 15 ppm had the effect of lowering sulfate emissions and enabling the development and implementation of catalyzed emissions control technology across a wide spectrum of applications."

Jan 12, 2017

By Ruichen Ren, Xu Han, Caixia Li, Zengchuan Yue

In this paper, the size-density distribution of coarse middling coking coal (CMCC) with different grinding fineness and flotation concentrates was investigated. Then, the flotation behaviors and liberation characteristics of different size-density fractions in ground CMCC were analyzed, and the different size-density fractions were divided into five categories: mostbeneficial, secondary-beneficial, poorly liberated, insignificant-pollution, and serious-pollution. Based on the content of particles with different liberation characteristics, an evaluation index of the liberation characteristic of ground CMCC, namely, the liberation perfection index (LPI), was proposed. The results indicated that grinding changed the size-density composition of CMCC, which affected the flotation performance. Insufficient grinding and overgrinding were not beneficial to flotation. Insufficient grinding caused a higher content of poorly liberated particles and a lower content of most-beneficial particles. Overgrinding increased the content of serious-pollution particles and reduced the content of most-beneficial particles. The size order of the LPI values of different ground CMCC was consistent with the flotation efficiency, and the LPI values of the other two similar samples were overall positively correlated with their flotation performance, suggesting that the method is universal.

Feb 14, 2023

By Diler Katircioglu-Bayel

The effects of the operating parameters of media filling ratio, solid mass fraction, grinding media size and grinding time on the stirred media milling of talc were studied. The findings were assessed based on the product particle size (d50, d10), surface area (Sw) and energy consumption (Em). Furthermore, after determining the optimum grinding conditions, Box-Behnken statistical design was used to determine the effect of parameter interactions on the d50 size. The media filling ratio significantly affects d50 size decrease compared with solid mass fraction and grinding time. The minimum d50 size was also achieved under optimum grinding conditions.

By A. Jahedsaravani, M. Massinaei, M. Zarie

Deep learning is a subset of machine learning that uses artificial neural networks for extracting high-level features from image data. In the present study, a soft sensor is proposed for the prediction of the flotation performance through froth features generated by the use of pre-trained convolutional neural networks. Several state-of-the-art convolutional neural networks (AlexNet, GoogLeNet, VGGNet, ResNet, and SqueezeNet) pre-trained on the ImageNet database are used to predict the metallurgical performance of two flotation systems. The first case study is a batch copper flotation system video-captured over a wide range of process conditions. The second case study is an industrial coal flotation column equipped with a continuous video recording system. The pre-trained networks are used to extract features from the froth images, and these features are subsequently used to predict the flotation conditions and performance. The prediction results by the pre-trained algorithms were compared with the traditional image processing algorithms. This demonstrates the ability of the pre-trained structures to generalize to images outside the ImageNet database. GoogLeNet outperforms other network architectures and provides more accurate predictions of the flotation process behavior and performance.

May 5, 2023

By S. Hamm

Elevated total dissolved solids (TDS) content in waters downstream from surface coal mines in Central Appalachia is an increasing concern, as unnaturally high TDS and/or associated specific conductivity (SC) may contribute to deteriorated stream ecosystem health. The aim of this preliminary study was to explore the efficacy of accelerated leaching as a means of minimizing long-term TDS/SC generation by problematic overburden materials. Five spoil samples were collected and leached using simulated rainwater solutions under ambient and acidified pH conditions. SC and pH were monitored during each leach cycle, and ICP-MS was used to determine how leaching conditions affected release of specific ions. This paper highlights the results of both jar and column leaching tests. Among the most significant findings was that, for certain spoil materials, SC in leach column effluent was effectively reduced when spoil was leached first with acidic rainwater followed by ambient rainwater (vs. ambient rainwater leaching alone). This suggests that accelerated leaching might aid in long-term stabilization of some materials.

Feb 23, 2014

By R. A. Cummings

From before the turn of the century until as recently as the 1950s, relatively shallow coal reserves near the margins of the Illinois Basin were extracted by room- and pillar methods. Subsequent development has, in many cases, extended onto ground with high subsidence potential. The same state of affairs exists in many other historical coal mining districts, as well as in Illinois. Pit subsidence in Illinois is particularly common in the towns of Streator, Carterville, and Herrin, although there are others. Pit subsidence is characterized by distinct circular or oval depressions and normally is associated with shallow mining and thick soil relative to the thickness of rock.

Jan 1, 1985

By Zeynep Aktuna

In this study, the formation of zeolites around Kizkapan and Karlikoy villages (Sothwest Kesan) were investigated. In this region, stratigrafically, Upper Eocene Kesan Formation, i.e. sandstone and rarely shale are observed at the bottom. Early Middle-Oligocene Yenimuhacir Formation is composed of sandstone, marl and tuffs. The zeolitisation is determined in the dasitic tuffs of the Yenimuhacir Formation. In this tuffs' zone, alteration had primarily resulted in zeolites, mainly mordenite, heulandite-clinoptiIolite. Silicification and alteration to clay minerals are also common. The Miocene-Pliocene Ergene Formation and alluvium deposits are the top units in the area. In the studied area, zeolite occurences have economic importance. The results show that successively rapid and short term periods are responsible for the clinoptilolite-heuylandite formations. The homogene chemistry of the solutions may be evaluated for a possible successive zeolitisation period. Multi-periodic vocanic activity and also circulation of thermal water had resulted in a continous dissolution of volcanic glass; moreover, resulted in the formation of suitable conditions of zeolite formation. The mineral crystallization sequences and alteration products as zeolites within the wall-rock, circulated solution reaction depends on a serie of parameters such as chemical composition of both initial materials and volcanic solutions during rock¬solution interaction period. The previous researches and the chemical studies support our results and observations in the studied area. The aim of this study is to investigate the presence of zeolitisation and to explain the formation steps of zeolitisation in Kesan Area by considering the content and distribution of major and minor elements determined in zeolite bearing tuffs. The chemical structures of both zeolite bearing volcanics and zeolite minerals are compared to the results of previous studies. Two dimentional behaviours of major and minor elements were discussed in order to caracterize zeolitisation development and to postulate a probable formation type of zeolitic alteration.

Jan 1, 2005

By George K. McCord

It is a pleasure to participate in this Fall meeting of the Society of Mining Engineers to discuss energy conservation trends in the cement industry. Energy is the "life blood" of American industry, and the ability to use available energy resources efficiently may well determine the future of our nation and of its industries. The Federal Energy Administration has classified cement manufacture as one of several energy-intensive industries in the U.S. and has selected the Portland Cement Association to make a detailed study of possible energy conservation measures. Member companies of the Portland Cement Association represent about 85% of the cement producing capacity of the United States and 100% of Canadian capacity. Stated briefly, the purpose of the Association is to extend the uses of portland cement and concrete through research and development, market promotion, education, and public affairs work. PCA's general offices and research laboratories are located in Skokie, Illinois. Our staff of engineers, scientists, and research personnel make the PCA uniquely qualified to perform an energy conservation study of the kind requested by FEA.

Jan 1, 1975

By Neel Gupta, Dustin M. Crandall, Brijes Mishra

X-ray computed tomography (CT) images of rock specimens often contain artifacts which must be corrected before scientific analyses are performed. This paper presents a new workflow of automated image processing to utilize poor-quality X-ray CT scan images. The workflow runs on the open-source image analysis software and efficiently separates desired features from low-contrast scanned images. The new workflow is a two-step technique using contrast enhancement and automated feature segmentation to generate noise-free binary images. The results of binary images using the proposed workflow and using a conventional thresholding technique are analyzed to show the quality of the proposed method. The paper also presents a workflow of estimating the structural geometries of features in two and three dimensions. The results of the structural feature analyses and computational time were compared between the open-source (ImageJ) and commercial image analysis software (Bruker Computed Tomography Analyzer). The commercial software was more computationally efficient, but the task-specific macros in open-source software enabled the user-desired automation in image processing and data extraction of desired structural features of comparable quality.

Sep 8, 2022

By Ihsan Berk Tulu, Gaobo Zhao, Deniz Tuncay, Syd S. Peng

Longwall mine instrumentation for measuring abutment stress distribution, mining induced immediate roof stress change and deformation, and primary/secondary support loads and deformations provides critical guidance for the design of gateroad chain pillars and roof support. Field measurement results are also recognized as the best way to calibrate numerical models that have been used to study the failure and support mechanisms. International Conference on Ground Control in Mining (ICGCM) started in 1981 and since then, there were 26 papers published in the proceedings discussing the stress and load measurements as the face advanced using various field instrumentation techniques. The focus of this paper is on summarizing the analyses of the data published in these papers. Stress/load change monitoring included the following categories: gateroad chain pillar, abutment pressure, bolt load, and pre-driven recovery room. The data shows that the magnitude of stress changes as the face advances varies considerably from panel to panel and mine to mine. However, regardless of types of stress changes, pillar stress, abutment pressure, and bolt load, there exists a rough trend of stress increase as the face advances, generally consisting of three stages, i.e., stress/load (1) initially increases steady or slowly, (2) increases rapidly, and (3) increases reaching the peaks and dropping down slowly or sharply. The stress/load increases start earlier during the second panel mining and are larger than the first panel mining. This review makes it easy for the interested persons to find valuable data for other similar projects.

By Saman Khaleghparast, Naj Aziz, Jan Nemcik, Guanyu Yang

"More than 25 years of uninterrupted research on ground support technology for underground mines has been undertaken at the University of Wollongong. This research has resulted in significant findings on tendon characteristics and strength properties. The paper focuses on the development of the fourth generation of cylindrically shaped shear test apparatus for assessing tendon performance in shear. This shear apparatus is known as the MK-IV Double Shear Box or Naj Aziz Double Shear Box (NADSB), and is based on the experience gained from the development of previous versions of rectangular double shear boxes. The new NADSB is circular in shape and is fitted with a truss system, which permits friction free shear testing of tendons across joint planes. A series of double shear tests were carried out on a number of cable bolts commonly used in Australian mines, both plain and indented wires, under varied pretension loads. The results were compared with similar test results using rectangular shaped double shear apparatus, with and without friction across joint faces. The significance of wire surface roughness and increased initial pretension loads are discussed and conclusions made, suggesting that indented wires are inferior in shear compared with plain cable bolts. The general test procedure of the NADSB is described and different concrete reinforcement techniques are reported. The influence of external and internal confinement of the concrete medium blocks in a circular double shear box contributed to consistent test results with a minimum of lateral and axial cracks occurring in the host medium.INTRODUCTIONThe use of long tendon ground support elements (cable bolts) is now a common practice in modern underground coal mines, hard rock mines, tunnels and other underground structures. Due to their material properties cable bolts contribute significantly to the overall ground reinforcement provided by a support system. Cable properties in tension and shear are in many cases vital to maintaining a safe and productive underground environment. Accordingly, tension and shear properties must be assessed accurately using both valid and reliable methods.Load transfer property testing of tendons has been studied over several decades with much of the early research focused on the pull and shear testing of solid rock bolts and hollow bolts (like Swellex and split set tube bolts), as these elements were used extensively at this time. It was not until the 1970’s that the use of cables for ground reinforcement developed, and as such highlighted the need to extend load transfer property testing to include shear strength of cable bolts. Initially, the discarded hoisting ropes were used for ground support in metal mines, particularly in stopping wall support and then late in 1980’s cable tendons began to use in coal mines."

Jan 1, 2019

By Tianzu Yang, Weifeng Liu, Lin Chen, BOYI XIE, DUCHAO ZHANG, HUI XIAO

The oxygen-rich bath smelting process of copper dross was simulated using Factsage software. It was found that the two-step simulation results agreed better with the industrial data, especially in the speiss. Bi, Pb, Sb, As, and Cu contents in the speiss by two-step simulation differed from the industrial data by 0.6 wt.%, 0.8 wt.%, 2.6 wt.%, 7.2 wt.%, and 8.6 wt.%, respectively. Twostep simulation results indicated that the speiss partitioning of Sb, As, and Cu increased from 60.1%, 32.3%, and 27.5%to 81.6%, 67.8%, and 47.2%, respectively, with the smelting temperature increasing from 1050 °C to 1250 °C. While the metal partitioning of Sb and Cu increased from 0% and 2.7% to 15.2% and 13.3%, respectively, with the separation temperature increasing from 400 °C to 700 °C.

Oct 19, 2020

By T. Tamagawa

A gaseous chlorination process for hydrometallurgical treatment of a chalcopyrite concentrate was investigated. The overall process is visualized to consist of low temperature chlorination-selective oxidation, followed by aqueous chloride leaching and SX-EW for producing electrolytic copper elemental sulfur and ferric oxide. In this article, the chlorination phase of the processes is described. Initially, the chlorination behavior of chalcopyrite-concentrate micro-pellets was investigated using a small batch-type fluidized bed reactor. The optimum conditions thereby established was used in continuous chlorination tests. The chlorinated products thus prepared were used in the selective oxidation phase of the investigation.

Jan 1, 1999

By Carmel Bofinger, Maureen E. Hassall, David Cliff, Eric Stemn

Incident investigation is of utmost importance in most high-risk industries and is often used to improve organisational safety. This study was undertaken to examine the content of past incident investigation reports to determine the effectiveness of the incident investigations. The study uses a semi-quantitative method to assess the effectiveness of incident investigations in the Ghanaian mining industry by evaluating the quality of past investigation reports. The assessment tool consists of five elements with several indicators and rating scales for assessing the quality of an investigation report as a measure of the effectiveness of the investigation. The method was applied to 304 investigation reports of three Ghanaian large-scale gold mines, and the results correlated with incidence rates of the mines to determine if any relationship existed. The results showed that the mines differ significantly in the quality of their investigation reports, suggesting differences in the effectiveness of their investigations. In addition, the incidence rates of the mines negatively correlated with some elements of the assessment tool. In general, the method was found useful and revealed areas where improvement is needed.

By W. R. Mackenzie, C. A. MacDonald

Oxide copper was discovered in 1946 at Guelb Moghrein. Early work culminated in the construction in 1970, by a consortium headed by the Anglo American group, of a project producing copper concentrates from 1,000,000 tonnes per annum of oxide ore. The process used was the TORCO (Treatment Of Refractory Copper Ores) process, which reduced oxide copper minerals to elemental copper by roasting in fluidised beds at 800°C with salt and coal. The roaster product was then floated to yield a high grade smelter concentrate, which was exported. The project closed in 1976, due to low copper prices and increased energy prices, leaving an open pit, the old TORCO plant, a water pipeline, and more than 2,000,000 tonnes of tail­ings, which contained remnant copper, as well as an average of 3 git of gold. After several attempts to recommence operations at Akjoujt, recovery of gold from the old TORCO tailings was started in 1992 by a joint venture company known as MORAK (Mines d'Or d'Akjoujt). This company comprises General Gold Resources N.L. of Australia, who are the managing partner, SAMlN (La Societe Arabe des Mines d'Inchiri) and the International Finance Corporation. Because the tailings are high in copper (0.1-0.3% Cu), the project used the 'Hunt' process, which uses a combination of cyanide and ammonia to leach gold while suppressing copper extraction. The gold is recovered from leach liquor by carbon absorption.

Jan 1, 1996

By Sandeep Kumar Asarapalli, Sunil Kumar Bisoyi, Bhatu Kumar Pal

Spontaneous heating of coal is one of the major concerns in the coal mining industry. Hundreds of millions of tons of coal are lost each year because of spontaneous heating. If necessary arrangements are made, many fires due to spontaneous heating may be avoided. Therefore, protective measures have become essential to prevent coal from spontaneous combustion. A large amount of coal reserve can be saved by the assessment, suppression, and prediction of spontaneous heating of coal, which also helps in betterment and efficient coal production. The use of chemical retardants can act as inhibitors for the liability of coal toward spontaneous heating by increasing its ignition temperature, thereby, increasing its incubation period. The coal-chemical mixture can be used for whitewashing the exposed coal in galleries as it creates a layer between coal and oxygen in the atmosphere, delaying the oxidation process and ultimately inhibiting the spontaneous heating liability of coal. This work examines the effect of chemicals such as sodium chloride, calcium carbonate, potassium iodide, sodium nitrate, and potassium chloride on the spontaneous heating of a coal sample. Thereby, it suggests a better chemical for inhibiting the liability of coal toward spontaneous heating. The experimentation involves flammability temperature (FT), crossing point temperature (CPT), and differential thermal analysis (DTA). The ignition and oxidation temperatures were found from the above experimental methods for Lingaraj open-cast coal mine samples, with and without adding chemicals. The results are cross-checked and verified through DTA. Correlation analysis was carried out among the results obtained from CPT, DTA, and FT, and better chemical retardants that effectively inhibit coal’s tendency toward spontaneous heating were suggested.

Dec 23, 2023

By Yuanbo Zhang, Yikang Tu, Zijian Su

Stainless steel swarf is a typical by-product produced from stainless steel processing, which contains a significant level of valuable metals, such as iron, chrome, and nickel. About 1 million tons of stainless steel swarf are generated in China annually, but as mixed with impurities such as Al and Si, stainless steel swarf is not suitable to be directly smelted into stainless steel through refining process. In this study, stainless steel swarf was applied as a strengthening agent during limonitic laterite sintering process. The effects of adding stainless steel swarf on green bed permeability, the yield and quality indexes of the sinters, and the microstructure of the sinters were evaluated systematically. The results showed that the concentrated distribution degree of granules and green bed permeability were improved after adding stainless steel swarf. As the additional amount of stainless steel swarf increased from 0 to 3%, the tumble index and yield of the sinters rose from 50.07 to 54.69% and from 62.04 to 67.35%, respectively. The addition of stainless steel swarf would not change the phase compositions, and had little adverse impact on the metallurgical properties of the limonitic laterite sinters.

Aug 23, 2023

By B. A. Wills

With the increasing need to mine lower grade ores, high energy-related costs in comminution are of major concern. Very fine grinding is needed to liberate the very fine mineral particles in these ores. Not only is this expensive but it leads to greater losses in 'slimes'. In the early 1970's, 50% of the tin mined in Bolivia, 30% of the phosphate mined in Florida and 20% of the world's tungsten were lost in this way (Somasundaran, 1979). Gravity concentration techniques become unacceptably inefficient for particle treatment below 25-50µm, and even flotation fails in the ultra-fine range. Two approaches can be adopted to try to overcome this problem. The first involves increasing the efficiency of existing equipment or developing new slimes treatment processes. Gravity devices such as the Bartles-Mozley concentrator have been developed for this purpose and good recovery has been reported from 100µm down to 5µm. Such machines, however, have relatively low throughputs, so that large areas of plant space are generally required. Flotation is rapidly growing in importance for the treatment of ultra-fine minerals traditionally treated by gravity concentration.

Jan 1, 1986

By J. C. Squire, E. W. Baker, G. A. Sullivan, G. W. Flathers

A mine collapse severs communication with trapped miners. Landlines are crushed and commercially available radios cannot penetrate hundreds of feet of dense, conductive earth without the use of regenerative repeaters that may also be crushed. This paper describes a proof-of-concept device that uses seismic P-waves, instead of radio waves, to allow communication of a code that represents prearranged messages, including the safe haven location identifier, number of people and air quality, from trapped miners to aboveground rescue units. The transmitter designed is about 0.03 m3 (1 ft3) in size and can broadcast for four hours from its 27-kg (60-lb) battery pack. The receiver consists of a geophone and a 2.5-kg (5.5- lb) signal conditioning unit attached to a laptop computer, which displays the communication signal in real time. Testing in a bituminous coal mine with an MSHA representative revealed the device was able to transmit through 271 m (890 ft) of overburden, at 0° and 12° from vertical, using 500 W of power.

Jan 1, 2009