Search Documents

By Felicia F. Peng

The manganese removal from aqueous solution containing high Mn2+ concentration by adsorption and oxidation was studied using manganese oxide particles as the adsorbent. The operating parameters including pH, flow rate, initial manganese concentrations, and oxidant dosage affect the performance of Mn2+ removal were evaluated in a laboratory packed column. In the multi-column adsorption tests, each additional column doubled the time for complete manganese removal. No further decrease of pH was also observed once it was lowered to pH 4.5 to 5. This finding implied the possibility of complete high manganese removal without further pH adjustment during adsorption. Oxidation of Mn2+ by dissolved oxygen was found to be insignificant for manganese removal for high Mn2+ concentration. Adsorption was the predominated mechanism involved with manganese removal. Extremely low H+/Mn2+ stoichiometry compared to the reported values was measured. These low values suggested that different adsorption mechanisms such as chemisorption other than H+/Mn2+ ion exchange might play an important role at low pH. This paper presents the quantity and explanation of the results obtained for the mechanism of adsorption and oxidation of high concentration manganese on the manganese ore particles.

Jan 1, 1997

By Brian P. Canning

Ion exchange resin processes are receiving renewed attention in the mining industry for recovery;, of metals from solution. This interest has been inspired by the development of continuous countercurrent ion; exchange systems (CCIX) which are of much lower cost than the original, fixed bed contactor processes. With the countercurrent systems and new developments to process or upgrade the eluate product, ion exchange can now compete successfully with solvent extraction for treatment of uranium ores. The low concentration of U308 obtained in the CCIX strong eluate is generally upgraded by solvent extraction methods in sulfuric acid systems. Resin loadings of up to 120 grams per liter of U308, however, have been produced experimentally by recycling of eluate (HIM-IX process) and further developments may be expected in the near future. New developments in resin technology are bringing forth products of greater strength, loading capacity, selectivity and density. Densities up, to 1.35 spgr have been claimed by some suppliers. The process is not a new one and has taken years to advance to the present state of development. The earliest system to gain widespread acceptance was the resin-in-pulp system applied to uranium recovery. Ion exchange, however, later lost acceptance in favor of solvent extraction in the 1960's due to problems in resin degradation, resin contamination and resin-pulp separation, in addition to the development of improved solvent extraction reagents and techniques. The resin-in-pulp system continues to have application on high clay ores and has advanced in design. A number of other continuous ion exchange systems were also tried but never gained continued acceptance. In the current resurgence period the CCIX systems to gain acceptance were the Utah and Chem-Sep (Higgins Loop) systems. These processes are relatively simple in concept although require sophisticated controls. Fixed bed columns have also been designed into multistage systems in countercurrent operation but are not discussed in this paper. These systems remain competitive today for many applications. The most recent advancements however have been in the multistage contactors from,, which three are in current acceptance. These are the Himsley, Porter, and NIM systems. All industrial applications of these systems are relatively new, although pilot plant and in-plant development has been in progress over the last decade. Fur36ther developments should be expected in the near future.

Jan 1, 1979

By Pratoomkhuan N. Lertsgoon

A large underground cavern with dimensions of 25m × 175m × 49m (W×L×H) was excavated in sandstone and siltstone to house 4 units of hydropower generator and was completed in 2000. In feasibility study stage, the property of the siltstone which governs the ceiling of the cavern was questionable due to slaking phenomenon. Parameters on rock properties for design were back calculated from actual ground response measured from a trial excavation. For safety of construction, comparison between prediction and actual ground responses during excavation had proceeded. The prediction was provided by means of PHASES and PHASE2 software and the actual rock response was detected by the provided monitoring system.

Jan 1, 2003

By D. Brabec

One of the analytical problems in exploration geochemistry is the choice of a method of sample attack which would be rapid, simple and reliable in terms of precision and discrimination between different concentration levels of elements sought. The wet sample attacks currently used in analysis of silicate rocks vary from total decomposition to leaching by weak extractants. The total decomposition of such materials is usually achieved either by alkaline fusion or hydrofluoric acid attack. The first method requires the use of platinum vessels which is both expensive and slow for batch operation. The second type of attack is more widely applied in rock geochemistry1, but it is still relatively slow for exploration purposes and requires extra care (especially when hydrofluoric acid is used in mixture with perchloric acid). Considerable improvement in speed can be achieved by using the sample attacks which release only part of the metal present in a rock.2,4 One of such attacks is the leaching of pulverized rocks by hot aqua regia.3 Another technique widely used in geochemical prospecting involves fusion of the samples with potassium pyrosulfate (or bisulfate) followed by an acid leach of the malt .5 One of the advantages of these techniques is the use of glassware in decomposition stage which considerably increases the analytical productivity. It should be noted that partial chemical attacks tend to extract from a rock mainly the non-silicate metal which may give results more significant for exploration purposes than the analysis for total metal.

Jan 1, 1970

By Alan Weakly

The Powder River Basin (PRB) of northeastern Wyoming and south-central Montana is the largest strippable reserve of compliant coal (0.6 or less lb of sulfur per million Btu) in the United States. In mining parlance, it is the Mother Lode! Wyoming’s portion of the Basin provides one fifth of the coal produced in the United States annually, and the state has been the nation’s top coal producer for the past six years. Based on 1993 production statistics and estimated strippable compliance coal reserves, Wyoming may remain the nation’s top producer for the next 76 plus years. Past articles on the PRB have focused mainly on production. After living and working in the Basin for the past five years, I have developed an appreciation for the area and its major industry that transcends size and production data. In the fall of 1993, MINING ENGINEERING’s publisher and I decided to present a series of articles that would cover many other aspects of the Basin. Ten topics were outlined, and specific individuals, selected for their knowledge and experience, were asked to contribute articles about their specialties. Although Montana has four large mines producing coal from the PRB, this series of articles will concentrate on the Wyoming portion of the Basin.

Jan 1, 1994

By Samer Sadek

The Georgia Department of Transportation (GDOT) undertook an exploratory feasibility study to one of the most ambitious tunneling projects in the United States. HNTB Corporation was retained to perform the study, deemed the Atlanta North-South Tunnel, which is approximately 7 miles long and consisting of four lanes (or six lanes) starting at the southern terminus of SR 400 extending to the south connecting with the northern terminus of I-675, providing substantial relief to the Downtown Connector (I-75/I-85), the most congested portion of Atlanta?s freeway system. This paper summarizes the analysis performed during the first phase of this challenging assignment which, if constructed, would be one of the longest roadway tunnels ever built in the United States.

By A. Arik

An accurate estimation of mining block grades continues to be a challenging task for ore reserve practitioners. Two of the factors that affect the accuracy of the estimates are the estimation method used and the variability of the mineralization in the deposit. The objectives of the study are twofold: Firstly, to see how different estimation methods perform on a given deposit. Secondly, to determine the impact of particular nature of the mineralization on the results. The comparison of several estimation methods for the prediction accuracy is performed using the conditional simulation results as the basis.

Jan 1, 2000

By Michael S. Moats, John Bailey Fletcher

The performance of grinding media can be misrepresented in marked ball wear tests due to galvanic interactions between dissimilar media. The possible galvanic interaction of media materials during marked ball wear tests has not been adequately explored. Corrosion rates and potentials of modern high carbon steel and high chromium white iron grinding media materials were measured using electrochemical testing as a function of pH and chloride content in a simulated mill water. The results replicate previous research with the high chromium white iron sample being more noble (higher corrosion potential) and corrosion resistant (small corrosion current) than high carbon steel. Using the experimental data and corrosion theory, the effects of galvanic coupling on corrosion rates were calculated to examine what could happen during a marked ball wear test or when a mixed media charge is present. This analysis indicates that high carbon steel can cathodically protect high chromium white iron leading to significant decreases in the corrosion rate (up to 99%) of this material during marked ball wear tests. The magnitude of the protection is a function of the pH of the mill water.

Dec 21, 2022

By S. K. Gilman

Zircon (ZrSiO4) sand production of about 1.1 Mt/a(1.2 million stpy) predominates the global supply of zirconium minerals. Baddeleyite (ZrO2) contributes less than 1 percent of supply. Zircon is almost exclusively produced as a co-product from the mining of titanium minerals, mainly from mineralized beach sands. In 2004, there were a number of new projects under consideration that were more dependent on zircon revenue than for titanium minerals. This reflected sustained higher zircon prices and forecast ongoing supply shortages in the absence of major new discoveries.

Jan 1, 2005

By James G. Mock

The choice of equipment to be applied to a given installation by the Application Engineer begins with the data as presented to him by the user. This point in the relationship establishes a communication link, which will decide whether or not the correct piece of Overhead Equipment is applied at the most economic advantage to the user. The role played by the user cannot be minimized. No one knows better than he, just what work he expects to accomplish with this piece of machinery. However, all too often, he oversimplifies the requirements, and along with minimal crane and building parameters, merely refers to one of the following crane classifications as defined by The Crane Manufacturing Association of America, as shown in Figures 1, 2, 3, 4, 5, 6 and 7. This approach places the ultimate user in an unfair position, since he has then assumed the status of the machinery designer and must, therefore, assume the responsibility of the success or failure of the operation of that piece of machinery. If the user selects a Class "C" crane for his job requirement, when actually a Class "B" crane can adequately handle the work load, he is not offering the most economic solution to his company and added little to the cranes service capabilities.

Jan 1, 1973

By N. Aouad

Dump truck operators are exposed to whole-body vibration (WBV) levels that exceed the International Standard Organization (ISO) 2631-1. The WBV level measured by RMS acceleration value, for operator comfort, and long-term health and safety is under 0.315 m/s2 by these standards. However, fundamental research by Frimpong and Aouad (2009, 2012) and field experimental study by Kumar (1999) have shown that operators are exposed to extreme WBV levels exposing them to injuries and musculoskeletal diseases in the long-term. These extreme WBV values in the vertical direction are equal to 3.56 m/s2, 1.12 m/s2 and 0.87 m/s2 for the operator?s seat, lower-back and cervical regions, respectively. This paper will outline current research to solve these problems. Keywords: WBV, Truck Vibrations, MSC.ADAMS, Virtual Prototyping

Feb 27, 2013

By Ray Brainard

Treated effluent from the Clean Water Coalition (CWC) member agencies is currently discharged at an annual average rate of 6,570 l/s into the Las Vegas Wash, and is increasing annually. As the effluent flow increases, the nutrient loading of the treated effluent will approach the maximum limits allowed under the current regulations. To manage this flow while maintaining water quality in Lake Mead, the CWC is implementing a 44-km-long conveyance system. This paper discusses the geological and geotechnical aspects of the 13.4-km-long tunneled section through the River Mountains and their effect on design. The tunnel alignment traverses a heterogeneous package of volcanic and sedimentary rocks exhibiting widely variable rock conditions.

Jan 1, 2008

The status and outlook for mining, in your view. Minerals remain a major part of the world’s economic foundation. The fortunes of the mining industry rise and fall with general economic trends, but mining is no less important today on a global basis than it has been historically. Certainly, portions of the industry are critically depressed — domestic copper to name one area —but other sectors are prospering. Mineral consumption, both worldwide and in the United States, has increased steadily since the Great Depression, hitting all-time highs in 2000, the last year for which I have seen data. The highly developed economy in the United States tends to obscure the continuing importance of minerals here. But in less developed nations the critical nature of minerals is obvious and well accepted. In short, although there is no shortage of problems or challenges facing mining — there never has been — mining remains an essential business with great global opportunity.

Jan 1, 2003

By M. Shen, T. D. Wheelock

The important characteristics of a gas-promoted oil agglomeration process for cleaning coal particles in an aqueous suspension were determined. Numerous agglomeration tests with scale-model mixing systems of different sizes with controlled amounts of air were conducted. The tests were conducted on high- and mediumvolatile bituminous coals using either i-octane or hexadecane as an oily agglomerant. The performance of the system was characterized by employing the minimum time required to produce spherical agglomerates (tE), the mean agglomerate diameter (dp), coal recovery and product ash content. Among these parameters, tE was found the most useful. It is a key parameter in the scale-up of an agglomeration mixing system. This parameter was found to depend on a number of system and operating variables. By controlling these variables and conducting further agglomeration tests with mixing systems that varied in size, an appropriate size scale-up rule was established.

Jan 1, 2002

By Jean Habimana

The Detroit Upper Rouge Tunnel CSO Control Project will capture and store up to 201 MG of combined sewer overflow from 28 outfalls in Detroit, Dearborn Heights and Redford Township during wet-weather events. The history of rock tunneling in the area is associated with high groundwater inflows, artesian pressure, and hazardous and combustible gases. This paper presents the geotechnical considerations for designing the 11.28-km (7-mile) long, 9.14 m (30-ft) finished diameter tunnel and its associated adits, chambers and shafts, including the discussions of geotechnical investigations, rock mass characterization, estimated groundwater infiltration during construction, and the selections of excavation methods and lining system based on anticipated ground behavior to be encountered.

Jan 1, 2008

By Garry G. Lowder

The regional geologic setting is essentially a volcanic island arc built upon an oceanic basement, consisting of basalt and minor pelagic sediments (the Tinombo Formation of Eocene - lower Miocene age. Trail et. al. 1974). -- An east-west chain of intermediate and acid calc-alkaline volcanoes (the Bilungala Volcanics) was built on the oceanic basement during the Miocene. The Bilungala Volcanics are flanked to the north largely by contemporaneous andesites and volcanoclastic sediments of the Dolokapa Formation. During middle to upper Miocene time the Bilungala Volcanics were invaded by large masses of predominantly dioritic intrusive rock and it is within one of these dioritic intrusive complexes, the Bone Diorite, that the cluster of porphyry copper systems occurs. Renewed volcanic activity in the Plio-Pleistocene produced acid pyroclastic rocks (the Pinogu Volcanicsi whose distribution is controlled by present-day topography. Structural trends, largely interpreted from SLR imagery, are pre- dominantly NW or NIWJ. The right-lateral Gorontalo Fault, which trends hW through the town of Gorontalo (Katili, 19691 is the most prominent structural feature. Many of the major structures in the Tapadaa district have similar orientations and may be sympathetically related to the Gorontalo Fault.

Jan 1, 1976

By Irvine G. Reilly

Results of a preliminary study of the ammoniacal leaching of covellite (CuS) in an aqueous oxidizing system in the presence of a non-miscible organic sulfur solvent are described. Up to 60% of the sulfur can be recovered from the solvent as elemental sulfur 1 while achieving high degrees of solubilization of the mineral. The effects of temperature, particle size, oxygen pressure, ammonia concentration and ammonium ion concentration on the degree of sulfur recovery were investigated. Maximum recoveries were achieved at moderate temperatures and in well-buffered systems, with a large excess ammonia concentration. Oxygen pressure and particle size were found to have little effect on fractional recovery of sulfur. A simple empirical model based on electrochemical theory correlating the effects of some of the parameters cont-rolling the degree of sulfur recovery is presented. The results of this work also confirm that in any proposed reaction mechanism for the oxidative ammoniacal leaching of copper sulfides, the primary oxidation product of the sulfide ion in elemental sulfur.

Jan 1, 1978

By Carrie Pourvahidi

The California High Speed Rail Authority (Authority) was created by the State of California through legislation in 1996. The purpose of the Authority is to plan, construct, finance and operate a statewide intercity high speed passenger rail system. In 2004 the Authority prepared a programmatic level environmental document in compliance with the California Environmental Quality and National Environmental Protection Acts (CEQA and NEPA).The Authority and Federal Railroad Administration (FRA) were the lead agencies overseeing the development of the environmental documentation. The resulting document includes two volumes and 64 supplemental technical reports analyzing the transportation needs for California and the selection of an approach to meeting the project transportation needs. The Programmatic Environmental Impact Report and Environmental Impact Statement (EIR/EIS) identified High Speed Rail as the most environ-mentally protective, sustainable and economical approach to meeting the state?s projected transportation needs.

Jan 1, 2008

By C. I. Walker

"Understanding the influence of slurry particle size on wear is essential to maximising the life of centrifugal pumps operating in mineral processing plants and for hydrotransport duties. Particle size influences not only the wear rate but also the wear pattern in pumps. Complicating the situation is the different relative wear rate for different pump parts depending on particle size. A simple Slurry Wear Type (SWT) number based on particle size and size distribution is proposed as a means for categorising slurry pump wear patterns and optimising pump application and material selection. INTRODUCTION The wear of centrifugal slurry pumps in mineral processing and hydrotransport can be quite severe and is one of the major cost concerns of plant operators. Some typical worn slurry pump parts made from high chrome white iron are shown in Figure 1. Erosion wear rates of up to 2 mm/day are not uncommon [1].Centrifugal slurry pumps are required to handle solid-liquid mixtures with a very wide range of particles extending from sub-micron size clay through to 200mm and larger cobbles. Particle size distribution can also vary widely from uniform and narrow (such as graded sand) through to very broad (such as grinding circuit slurries). Slurry particles may also undergo size change due to attrition during the pumping process. The major wearing parts in a slurry pump are the impeller, side liners and casing liner. These are shown with reference to a Warman® MC centrifugal pump in Figure 2. While many particle properties (including size, shape, hardness, density and concentration) influence pump wear, this work will consider only the effect of particle size as it is the major determinant of wear characteristics. Particle size influences the wear pattern, material performance and relative component wear rate in centrifugal slurry pumps. SLURRY WEAR TYPE (SWT) BASED ON PARTICLE SIZE Soil and grain size classification systems abound. Many have different limits to the ranges for a particular classification, albeit not too"

Jan 1, 2018

By W. G. Stevenson

The centennial celebration of the AIME provides an opportunity to review some aspects of developments in mineral exploration since 1871 and to reflect on the changes that have occurred. During this period seven Factors have fundamentally altered the procedures, techniques and philosophy of mineral exploration. Although most of these developed gradually, and unheralded, they have drastically altered the art of exploration and discovery. 1. ADVANCES IN MINING AND MILLING The development of huge shovels, draglines, trucks and track-mounted drills, to replace the wheelbarrow and single Jack has drastically expanded the rate of production for both underground and surface mining. The development of selective flotation has had a far-reaching affect on mineral exploration and has made it possible to extract metals from the metallurgically complex deposits discovered years before. These developments have reduced the costs of mining and treatment, and have transformed material into ore that was considered waste one hundred years ago. These advances have permitted exploration for progressively lower grade and larger mineral deposits.

Jan 1, 1971