Search Documents

By Gregg W. Davidson, J. Andrew McGlenn, Frank Huber

The Second Narrows Water Supply Tunnel will ensure system reliability in the event of a major earthquake and increase the Greater Vancouver Water District’s capacity to meet the long-term needs of a growing population. The tunnel will be 1,100 m long and 6.5 m in diameter (3,610 LF × 21.3 ft), constructed under Burrard Inlet between North Vancouver and Burnaby in British Columbia. It will be excavated through mixed ground conditions under high groundwater pressure, using a slurry TBM, between a 72 m (236 ft) deep shaft in soil and a 110 m (361 ft) deep shaft in rock. The completed tunnel will accommodate three large-diameter water mains that will be installed as part of the tunnel contract. This paper presents the project from design and contractor procurement, into the current construction stage describing some of the unique challenges encountered during the project development to date.

Jun 13, 2021

By R. M. Von Storch

Most coal mining areas of the Western United States are characterized either by thick beds, steep pitches or heavy cover. Individually, each of these may present inherent safety hazards that influence miring. When all are met at one location, the combined effect is to make the safe operation of the mining property a challenge to management. These combined, conditions are met in most coal mines in southeastern Utah including those of the United States Steel Corporation. This coal bed measures up to 16 feet in thickness, the pitch is as much as 25% and mining is under a cover approaching 2, 000 feet. The Sunnyside coal bed is found in the Book Cliff Mountains, a great escarpment extending from west of Castle Gate, Utah, some 180 miles to Grand Junction, Colorado. West of Green River, Utah, the Book Cliffs swing sharply to the north because of the domelike uplift of the San Rafael Swell to the southwest..It is in this northerly extension of the Book Cliffs that the Sunnyside coal in the Blackhawk Formation of the Mesa Verde Group, Upper Cretaceous Age is found. The strata are transected by numerous faults with from a few inches to as much as a hundred feet of displacement. All of these faults have had some effect on the mining operation, either in roof control or, in the case of major faulting, the pattern of mine development.

Jan 1, 1967

By Brian E. Gombos

During early stages of the detailed design for Detroit?s Upper Rouge CSO Tunnel Project, a Value Engineering Recommendation suggested the design team investigate alternative concepts to the usual cast-in-place or precast concrete lining system for the Project?s many smaller diameter Deaeration Vent Shafts. The resulting design investigation produced not only an alternative lining system, but lead to a proposed non-conventional approach to shaft installation means and methods through soil and rock necessary to construct the permanent shaft lining system. This paper will outline and summarize the technical issues, contractual restrictions, and cost considerations that eventually lead to the final shaft design

By Jürgen F. Brune, SAMUEL A. LOLON, ADITYA JUGANDA, Gregory E. Bogin Jr

Historically, there have been many occurrences ofmine fires and explosions recorded in the United States and other countries that have demonstrated the existence of explosivemethane–airmixtures, herein referred to as explosive gas zones (EGZs). The risk of mine explosions can increase if the EGZs migrate out from the gob into the surrounding mine entries. Fluctuating barometric pressure is the common cause for EGZs outflowing or outgassing from the gob. Numerical analysis using a 3D computational fluid dynamics method was developed to fully understand the outgassing phenomenon. A number of simulations using various magnitudes and periods of barometric pressure changes indicated that the EGZ outgassing potentially occurs due to lags in pressure, which are strongly influenced by mine conditions and ventilation systems. An early warning system with a real-time pressure monitoring and the application of gob ventilation boreholes are recommended to detect and mitigate explosion hazards from gob outgassing.

Aug 24, 2020

By Karl Gunnar Holter, Frank Clement

"INTRODUCTION Typically waterproofing of conventionally excavated tunnels has been done by installing pre-fabricated sheet membranes between the primary temporary support lining and the secondary permanent inner lining. The membrane acts as a separation or sliding layer between the linings, which is often desirable. The geotextile installed behind the sheet membrane provides the required drainage and protection of the system. The design of the tunnel lining is strongly influenced and limited by the use of waterproofing sheet membranes. Since primary and secondary linings are separated from each other, forming a double-shell lining system. In that case the secondary lining must be designed for all permanent loads, although the sprayed concrete primary lining continues resists ground and water loads for a long time after construction. Significant progress has been made in sprayed concrete technology over the last two decades, with advanced admixtures, as well as the improved application technology using spraying robots. The development of new admixtures like superplasticizers based on poly-carboxylates, alkali free accelerators and silica fume, enables designers to use permanent sprayed concrete linings (SCL) increasingly for long-term service life. When designed and applied correctly, sprayed concrete can be considered as permanent. The use of spray applied membranes has seen increased use over the last decade in some countries, and demonstrated functionality and cost-effectiveness in several situations. This paper describes the use of the sprayed waterproofing membrane MasterSeal 345, an EVA polymer based product, and the practical experiences from several projects. SPRAY APPLIED WATERPROOFING MEMBRANES The sprayed waterproofing membrane is polymer based and has been especially developed for underground structures. The membrane is applied between primary and secondary concrete linings and develops high bond strength on both sides to the concrete (doubled-bonded)."

Jan 1, 2016

By S. J. Schatzel

Longwall coal mine operators in the US are required to ventilate multi-panel longwall districts but may have little or no knowledge about what happens to the ventilation air between the inlet evaluation points (IEPs), bleeder evaluation points (BEPs), and bleeder fans. The effectiveness of bleeder performance can directly influence the ability of a ventilation system to remove and dilute coal bed methane emissions. Consequently, the performance of coal mine bleeders is an important aspect of underground worker safety. U.S. coal mining stakeholders have acknowledged their belief that the T- junction split at the longwall face tailgate corner is very important in controlling the distribution of ventilation air. The percentage of air directed inby towards the bleeders and bleeder fan and outby to the submains is often not well-defined and can vary over the life of a longwall panel. To obtain direct measurements of bleeder performance, a tracer gas, sulfur hexafluoride (SF6), was released into the intake air stream along the panline of active longwall panels and in the bleeder/gob ventilation air inlets of an inactive panel. Tracer gas sampling was conducted underground using tube bundles attached to permissible vacuum pumps in the gateroads, former gateroads, and bleeders. Surface tracer gas monitoring was also conducted from operating gob boreholes and from bleeder fans. Testing was performed on multiple longwall panels which included various phases of longwall development and variable path lengths of ventilation air transport to bleeder fan installations. The applied methodology defines and describes coal bed gas pathways, rates, and volumes of movement at the bleeder/gob interfaces, and indicates flow rates for air/gas mixtures within these gobs. These findings are reported for three stages of longwall extraction using direct field-based measurements. Changes in the T-junction ventilation air distribution over the life of a longwall panel and its variable effect on panel ventilation airflow are discussed. These findings will assess the effectiveness of commonly applied ventilation strategies for improving air distribution and ventilation controls to meet statutory requirements and to achieve the desired ventilation patterns through multiple phases of longwall panel extraction.

Jan 1, 2011

By Patrick R. Taylor

United States Antimony Corporation, at its Yankee Fork property in central Idaho, is currently using a combination of flotation, gravity-amalgamation, and concentrate cyanide leaching, silver sulfide precipitation, and activated charcoal loading to recover both silver and gold. Tine processes of flotation, milling, gravity concentration, amalgamation, concentrate leaching, sulfide precipitation and gold recovery via charcoal are discussed. The flow sheet illustrates the use of cyanidation as an alternative to shipment to a smelter.

Jan 1, 1984

By H. Kinilakodi

In 2008, the authors developed a methodology for identifying underground coal mines at high risk for major-hazard events. It focused on major hazard-related violations of safety standards associated with high-risk conditions. Later, using a sample of 103 mines with 2008 and 2009 data, injury measures and U.S. Mine Safety and Health Administration (MSHA) citation data were combined into a safe performance index (SPI). The SPI was used to assess the relative safety-related risk of mines, including by mine-size category. In this paper, comparisons are made of SPI-associated, normalized safety performance measures across mine-size categories, with emphasis on small-mine safety performance as compared to large and medium-sized mines. Mining Engineering, 2011, Vol. 63, No. 10, pp. 73-77. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By James E. Lawver

During the past century, the Florida Phosphate Industry has established an enviable record of innovative technology in nearly all aspects of mining and beneficiation. A notable exception is the lack of technology to improve the present practice of storing waste clay in earthen dams. The rule which has been adopted by the Department of Natural Resources states, "Since storage of clay wastes for long periods of time interferes with expeditious reclamation and since above grade storage of clays takes otherwise useful land out of production and raises potential health and safety problems, below grade storage and rapid reclamation techniques are encouraged." The two waste products from the beneficiation plant are clay slimes (-0.1 mm in size) and sand tailings. The sand tailings do not present a problem since the tailings rapidly dewater to a dry weight of about 100 pounds/ft3 and make good land fill. By contrast, disposal of waste clay slimes is a formidable task. The basic problem is simply that the waste clay not only dewaters very slowly, but also that the ultimate solids content is very low and in most cases the volume of the clay greatly exceeds the available volume of below ground storage of the mined land.

Jan 1, 1984

By B. K. Cantrell

The U.S. Bureau of Mines and others have conducted a number of occupational exposure surveys since the publication of the International Agency for Research on Cancer report of 1989, which labeled diesel exhaust as a probable human carcinogen. These surveys have assessed diesel exhaust exposure using measurement of diesel aerosol and/or specific polycyclic aromatic hydrocarbons as indicators of exposure. This paper reviews present diesel emission standards, available diesel exhaust aerosol measurement techniques, and the results of the occupational exposure surveys. In the surveys, diesel aerosol was emphasized because it is a major component of diesel exhaust, is suspected to contribute to the health hazard, and is readily measurable. Three primary aerosol measurement techniques were used: respirable combustible dust, size-selective sampling, and measurement of the elemental carbon fraction. Occupations surveyed included mine workers, railroad workers, forklift operators, fire fighters and truck drivers. The studies found mean diesel aerosol concentration levels in the range of 0.004 to 1.74 mg/m3? Highest aerosol exposures were in confined spaces such as mines where heavy diesel equipment is used. Polycyclic aromatic hydrocarbons typically are found at very low concentration levels and are not unique to diesel exhaust.

Jan 1, 1996

By Chuang Sun, Feng Luo, Guo‑dong Li, Xue‑qing Li, Tuan He

The mining-induced failure of the coal seam floor is essential for water inrush. The mining disturbance to the floor, especially in the thick coal seam, is severe, and the water inrush risk is also higher than that in regular thick coal seam excavation. The superposition of many stresses, including in situ stress, mining-induced stress, and confined water pressure, must be considered in the prediction of the floor failure depth. This study adopted the elasticity analysis, FLAC3D numerical simulation, and on-site acoustic wave test comprehensively. The thick coal seam working face of the Zhong-Yu coal mine affected by confined water was selected as the engineering background to study the characteristics of the floor failure. Based on elastic foundation theory and the superposition principle, the mechanical model and the failure depth criterion of the floor were established, respectively. The distribution and evolution of mining-induced stress and the plastic zone in surrounding rock during the mining process are obtained by FLAC3D. In addition, the changes in the P-wave wave velocity in the floor before and after mining were compared and studied by the acoustic wave test method. The range of floor damage depth is determined on the basis of the above research.

Jun 8, 2022

By Matthias Rheinlander

The paper will describe Virtual Design and Construction (VDC) as a tool which will enable us to build a project ?virtually? on a computer before constructing and operating it in the real world. VDC computer models are built, using information from various sources including survey, 3D laser scanning, CAD and GIS to represent the project and its components in a coordinated and consolidated infrastructure model. This model is reviewed and evaluated by, and shared among project teams including owners, con-tractors, designers, engineers, construction managers, stakeholders and operators. It allows teams to fix costly design and construction issues before construction on site. Benefits and lessons learned from global projects will be discussed

By William R. Bond

The pressure/vacuum lysimeter is being used as an effective vadose zone monitoring device for mining heap leach facilities, tailing disposal ponds and tailing waste sites. Their use has proven reliable for baseline data collection, early warning leakage detection and analyzing geochemical variations in the vadose zone. The lysimeter structure utilizes a closed cylindrical chamber made of PVC or inert material. The soil water intake portion of the cylinder is made of a porous material of low permeability. The application of vacuum or pressure to the unit is via two access tubes from the ground surface. Available soil moisture is drawn by vacuum through porous material into the lysimeter chamber and then collected from the access tubes. Case studies show their usefulness for monitoring around a uranium tailing pond constructed in glacial till material, under heap leach pads and pregnant, barren, and overflow ponds, and investigating the movement of contaminant moisture through old tailing deposits. Relatively easy to install and sample, regulatory agencies and facility operators are accepting and negotiating for their application as a site integrity monitoring device and unsaturated zone research tool. Their use at heap leach facilities lends credibility to solution balance calculations when considering a leachate loss of 5 or 10 percent can make or break a mine's profitability.

Jan 1, 1984

By Charles Ronkos, Jeffrey Edwards, Brian Brodsky

The Marlin gold-silver deposit is in western Guatemala, 15 kilometers south of a major transform fault that separates the North American and Caribbean plates. A district-scale, northwest-trending graben controlled deposition of a greater than 1200 meter thick upper Tertiary quartz latite to rhyolite volcaniclastic sequence. These volcanics were subsequently intruded and unconformably overlain by a small intermediate, latite to andesite, volcanic complex. Classic low-sulfidation, quartz-calcite-adularia veins and stockwork formed a 2.2 million ounce gold deposit, in association with late-stage andesite dike swarms, along a west-northwest striking normal fault on the eastern flank of the volcanic complex.

Jan 1, 2005

Water and wind erosion of toxic zinc and lead smelter waste is one of the most urgent environmental problems to be solved in the Silesia region of Poland. Over 87 x 106 Mg of various mining wastes were disposed of in uncontrolled piles leading to soil, water, and air pollution in highly populated areas. Welz and Doerschel process Pb/Zn smelter wastes were stabilized in the summer of 1994 by application of heavy loads of CaCO3 (30 Mg/ha), CaO (1.5 -15 Mg/ha), and municipal biosolids (150 -300 Mg/ha), followed by seeding with a mixture of acid-and salt-tolerant grass species selected in a pot experiment. Vegetation was successfully established on 85% of the Welz material demonstration plot area (0.5 ha), even though it was initially high in water-soluble Zn, Pb, and Cd ranging from 0.4 to 1311,0.1 to 5.8, and 0.05 to 55 mg/kg, respectively. Standing biomass averaged 3.3 Mg/ha on the stabilized Welz waste zone by the end of the third growing season (1997). The revegetation of much of the Doerschel material area failed initially because of extremely high salinity (16 dS m-1), high content of water soluble metals (Cd in particular), and heavy compaction. The area was capped (15 cm) with waste lime and retreated with bio-solids (300 Mg/ha) in 1995, and standing biomass averaged 2.9 Mg/ha in the fall of 1997. The observed plant response to bio-solids and lime indicates this approach to be an environmentally beneficial technology as compared to the traditional methods utilizing topsoil covers.

Jan 1, 1999

By Fernando Humberto Muge

One of the problems that arises in the early stages of the mine planning before the determination of the mining exploitation method is to predict what will be the recoverable ore reserves in tonnage, grade and metal quantity, if the select ion is based upon block grades. The estimation of these recuperation or recoverable functions can act as an important planning tool in what concerns the appraisal of the consequences of ore-waste discrimination of individual blocks in a selective mining operation. Estimation methods of all these functions are discussed together with cross validation tests using the available information concerning a preliminary drilling campaign accomplished during the exploration stage of an iron orebody located in the North of Portugal (Moncorvo Orebody).

Jan 1, 1982

By William R. Yernberg

The combined 79th Annual Minnesota Section of SME Meeting and 67th Annual University of Minnesota Mining Symposium was held April 11 and 12, 2006, in Duluth, MN. About 300 mining professionals attended, including engineers, executives, mining managers and suppliers, from throughout the United States and Canada. This year’s theme was “Success in the New World of Mining.” The SME Minnesota Section meeting included a keynote session, a special projects update, a general managers update and technical paper presentations. The University of Minnesota Mining Symposium program featured a panel discussion on Minnesota’s relationship with China. The combined meeting included a trade-show consisting of 64 booth spaces. Tradeshow demand exceeded expectations, and an additional 10 booth spaces were added in the registration lobby. Also included were an SME short course on pump basics and social events.

Jan 1, 2006

Room-and-pillar mining at White Pine started in 1953 from a sub-outcropping orebody that gently dips to 1000 m depths in a distance of about 6 km. High horizontal stresses were recognized in the mid-1960s which had obvious stability impacts when viewed in combination with the increased overburden stresses. Modifications in conventional room-and-pillar design were introduced through the years on a trial-and-error basis to help overcome stability and resource recovery problems. These modifications were based on pressure arch concepts using pillar yielding and/or pillar recovery, and on mine layout orientation to minimize stress impacts. While some of these modifications were successfully applied in some areas, they failed in others. Through the years, visual observations played a major role in panel design with contributions from stress measurements and analyses. However, the down slide in the copper economy during the 1970s and early 1980s resulted in a loss of interest in the application of these concepts. This paper reviews ground control problems and presents the results of recent stress measurements and computer analyses. They shed light on the importance of using yield pillars and mine layout orientation to control stresses at depth.

Jan 1, 1993

By George P. Demopoulos, Vladimiros G. Papangelakis, Dimitrios Filippou, A. J. Monhemius, G. W. Warren, E. Peters

A new method developed for the estimation of the activity of Ht in mixed sulfate solutions is described and examples of application of this method to the system H2SO4-ZnSO4-FeSO4-Fe2(SO4)3 from 298 to 473 K are offered. The method makes use of an "extended Debye-Hiickel" type of equation that was originally put forth by Das for pure H2SO4 solutions at ambient temperature. The treatment of mixed sulfate solutions was made possible by combining that equation of Das with a speciation algorithm which calculates the abundance of all species formed. The developed method, which also takes into account ionic strength and temperature effects, was used to generate hydrogen ion activity and speciation data for all possible acid/metal sulfate pairs of the system H2SO4-ZnSO4-FeSO4-Fe2(SO4)3. Finally, under the light of the reported data, specific examples of hydrometallurgical reaction systems are analyzed in terms of thermodynamics or kinetics. In particular, the systems discussed are: hydrometallurgical precipitation of hematite, solvent extraction of Fe(III), acid leaching of zinc ferrite, and oxidation of Fe(II) to Fe(III) by O2(aq).

Jan 1, 1993

Caterpillar said it will produce a Cat line of ac electric drive mining trucks. The world’s largest manufacturer of mining and construction equipment said the addition of an AC electric drive truck line will provide its customers with products to fit key applications. “We are very proud of the strong leadership position that Caterpillar has attained with its mechanical drive trucks, and we will continue to invest in strengthening that position,” said Chris Curfman, president of Caterpillar’s Global Mining Division and Caterpillar Inc. vice president. “We also recognize that there are unique applications that would make the addition of ac electric drive an important and attractive complement to our current truck line.” This is the largest investment Caterpillar has made in mining trucks in its history.

Jan 1, 2006