Search Documents

By L. M. Cenegy

Introduction The formation of scale is common in gold ore processing plants. A working definition of such scale is: "A hard, tightly adhering deposit formed in place by the precipitation of calcium-bearing mineral compounds from water." The most common scale found in gold processing plants is calcium carbonate (CaCO3) although calcium sulfate (CaSO4) is occasionally a problem. The problem of scale in carbon strip circuits Carbon strip circuits present a particularly challenging scale inhibition problem. Many of the factors that tend to promote scaling are present in these systems. For example, carbon strip circuits are run at high temperatures and high pH levels and require long batch cycle times. Tortuous paths are encountered by the strip solution circulating through heat exchangers, pipes and elbows, causing transient pressure drops throughout the system. Severe conditions such as these cause the water to possess a high scaling potential and may lead to the breakdown of some of common types of scale inhibitors. Formation of scale Natural waters contain dissolved minerals and gases that promote scaling. One of the contained gases, carbon dioxide (CO2), is an important factor in scale deposition. Carbon dioxide dissolves in water to yield carbonic acid according to the following reaction: [CO2 + H2O - H2CO3 (carbonic acid)] Carbonic acid rapidly dissociates to yield bicarbonate and carbonate ions depending on the pH of the system: [H2CO3 -s H+ + HCO-3 (pH range 6-10) HCO3 -a H+ + COO (pH range > 9)] In gold cyanidation processes, lime is added to raise the pH of the mill solution to 10 or above to promote cyanidation of the gold and to eliminate the possibility of hydrogen cyanide (HCN) formation. Lime contributes both hydroxyl ions (OH--) and calcium ions (Ca++) to the solution. The normal scale forming reactions in mill water systems were described by Beasley (1973) as: [HCO-3 + OH -s C03 + H2O Ca++ + C03 -a CaCO3] Factor affecting scale deposition According to Linke's (1958) solubility tables, the solubility of calcium carbonate in carbon-dioxide free water is only 13 mg/dm3 (13 mg/L) at 25° C (77° F). Scale deposition occurs when the concentration of calcium and carbonate ions in the solution exceeds the solubility of calcium carbonate. This occurs, in most cases, when the water has undergone some chemical or physical change. Some typical changes that might occur that lead to scale deposition are discussed below. Temperature An increase in temperature can greatly increase the tendency to form calcium carbonate scale. Studies by Miller (1952) have indicated that calcium carbonate is less soluble at higher temperatures. Hence, high temperatures promote scaling. For this reason, scale is often noticed on heat exchangers, autoclaves and other high temperature surfaces. Pressure A decrease in pressure may lead to an increase in the tendency to form calcium carbonate scale. Fulford's (1967) work has shown that scale is more soluble at high pressures. Hence, scale is likely to be prevalent in pump suction lines, elbows, baffles and other areas that produce turbulence and subsequent pressure drops. Change in pH Calcium carbonate scale is pH dependent and tends to form more readily at high pH. Any event that causes an increase in pH, such as the introduction of lime or caustic, would tend to initiate scale formation. Since most gold recovery operations are run at a pH above 10, the tendency to form calcium carbonate scale is always great. The use of scale inhibitors to prevent calcium carbonate scale Many products are commercially available to inhibit the formation of calcium carbonate scale. Some of the more effective types include phosphonates, as well as acrylate and maleate-based polymers and copolymers. Many of these products function by means of threshold

Jan 1, 1992

By J. L. Cupp, R. C. Ford, B. R. Romig

The Climax Molybdenum Mine, located near Leadville, Colorado, is the site of a lengthy mining history spanning more than 80 years. In the 1960’s, extraction of molybdenum from oxide ore located adjacent to the massive molybdenite sulfide deposit resulted in the construction of an earthen core dam to impound fine-grained oxide tailing in the Eagle River Valley. Through recognized value of water storage and reclamation opportunities, a tailing removal project was initiated in 1993 to convert the impoundment facilities to a post-mining beneficial land use of developed water resources. An evaluation of the effect residual materials and lake dynamics would have on in-stream water quality was performed. Eagle Park Reservoir stands as a model for future reclamation efforts that involve water delivery to highly sensitive receiving waters. This paper provides a case study on project development, the evolution of water quality assessment, and the regulatory framework that contributed to this project’s success.

Jan 1, 1999

By L. A. Pursell

The case history, which is the subject of this paper, involves the expansion of a lime plant in Texas. The major new production unit is to be a 545.45 tonne per day coal fired rotary kiln. Auxiliary facilities include additional quarry haulage equipment, modifications to the crushing plant, a hydrator, storage facilities, and a loading system. The existing plant consists of a high calcium limestone quarry, two coal fired rotary and 10 gas fired shaft kilns, nth crushing, screening, stockpiling, hydrating, storing and loading facilities. The proposed modification would increase quarry volume from 545,000 tonnes per year to 805,000 tonnes per year. The plan also includes the addition of dolomitic lime to the product line which requires the purchase and handling of 186,000 tonnes of screened, washed dolomite yearly. A decision to undertake such an expansion was previously a simple and straight forward process. Such a decision now faces a major and complicating obstacle which can delay the project, raise the expected cost, or prevent it entirely.

Jan 1, 1980

By G. P. Salas

I.- In order to keep pace feeding its fast growing population, Mexico with only about 20% of its surface suitable for intensive agriculture, will need the application of modern foodgrowing techniques. To assure greater crop yields it will be necessary to apply more fertilizers than used at present (yearly average of 29 Kgs/hectare)** For its fertilizers production Mexico still depends mostly on imports of phosphate concentrates from Florida, U.S.A., Morocco and Spain. To reduce or eliminate this dependence on foreign providers, the Consejo de Recursos Minerales -a Federal Government exploration Institute- started in 1974 an exhaustive exploration program for phosphate deposits more amenable to commercial exploitation than the phosphatic limestones contained within the La Caja Formation of Upper Jurassic, found along the Sierra Madre Oriental. After studying literature on the origin and deposition of marine phosphate and visits to deposits in Florida, U.S.A., the Baja California peninsula was selected as most favorable for starting this program because of its geologic and sedimentary history and also for its geographic location, where the cold California and warm Counterequatorial currents meet. Exploration activities executed by FORNOS, S. A. (1956) led to the disco very of low grade phosphate (3 to 5% P2O5) in the recent beach sands along the Bahia de Magdalena (Fig. # 1). In his doctoral thesis Bruno D'Anglejan Chatillon (1965) reports the presence of nodular phosphate on the continental shelf, between Isla Margarita and the Vizcaino peninsula. He estimated reserves of up to 1.5 million tons. A Mexican-American marine exploration company attempted in 1966 the evaluation of this deposit with negative results.

Jan 1, 1978

Seven legendary figures of American mining will be enshrined in the National Mining Hall of Fame in ceremonies on Saturday, Sept. 7 at the Little America Hotel in Salt Lake City, UT. The 15th annual induction banquet will begin with a reception at 6 pm, followed at 7 pm by the dinner and the program. Of the seven inductees, one is living. He is Alexander Murray (Bud) Wilson, 80, of Los Altos, CA. Wilson led Utah Construction (later Utah International) to become one of the world’s most diversified and successful mining companies in the 1960s and 1970s. It was acquired by General Electric in 1976.

Jan 1, 2002

By A. R. Bell

Rio Algom Limited are currently undergoing a major expansion of their mining operations in the Elliot Lake area. To date this has involved the increase of output at the Quirke Mine from 4080 to 6350 tonnes per mill day (4500 to 7000 tons), the rehabilitation of the Panel Mine to produce at the rate of 2990 tonnes per mill day (3300 tons) by 1980, and the rehabilitation of the Stanleigh Mine to produce 4540 tonnes per mill day (5000 tons) by 1984. In addition, the planning for the rehabilitation of the Milliken Mine to produce 4990 tonnes per mill day (5500 tons) is now underway. This major expansion is taking place at a time of increasing awareness of occupational health matters and has involved very high capital expenditures and detailed planning related to the ventilation system to endeavour the provision of an acceptable environment. The paper discusses the ventilation systems, established and proposed, and relates them to historical and current data on mine air contaminants.

Jan 1, 1980

By Jon Ike Isaacson, Michael Miller, Jarek Trela

Despite reef structures being relatively common in carbonate rocks around the world, tunneling experience in reefs is extremely rare. Impacts and risks associated with reef tunneling through these geologic features were also relatively unknown. A new reef was encountered during construction of the Lower Pogues Run Tunnel in Indianapolis, exposed over 5,000 linear feet along the alignment, resulting in adverse impacts on construction. Analysis of investigation data and construction from this encounter provide insight into the identification and characterization of reefs along tunnel alignments as well as the potential impacts on construction for future tunneling within reef structures.

Jun 23, 2024

By E. Steiakakis, A. Athousaki

Nowadays, stakeholders have a strong say to the enforcement of best practices by mining and quarrying companies. In most cases there is a direct relationship between sustainable development principles and best practices. Mining companies try to apply best practices in order to sustain their operation without lost time and effort to litigation, and other obstacles. However, when and where there is a lack of state or regional mineral policy, or when the mineral policy is fragmented and touching on conflicting laws, mining operations may be subject to additional administrative hassles, and, thus, operators feel threatened and tend to apply best practices loosely. This paper argues that the only way that mining and minerals operations can be a source of development is to ensure that they are working within the framework of sustainable development. Furthermore, in order to follow the paradigm of sustainable development they would need to be guided by a regional, national or even transnational (i.e. European) minerals policy.

Jan 1, 2011

By R. P. Schneider

The Chino mine, concentrator, and smelter are located in Grant County in Southwestern New Mexico. Chino Mines Company is a partnership two-thirds owned and operated by Kennecott Santa Fe Corp., and one-third owned by MC Minerals Corp. (Mitsubishi) of Japan. The Chino Ore Body The Chino ore body is a widely varied deposit of rock types and contains intrusive stocks and sediments. The stocks contain chalcocite in a matrix of quartz, mica, and feldspar. Much of the feldspar is altered to clay. Some of these stocks are enriched with native copper. The sediments contain chalcopyrite associated with gangue minerals including magnetite, pyrite, garnet chlorite, and epidote. The contact of the stock and sediment is heavily altered to chlorite and clay. The stock ores contain economic quantities of molybdenite. The operating work index of Chino ore varies from 5 to 20 kwh/ton and averages 8.5 kwh/ton. The ore head to the concentrator averaged 0.81% copper and 0.010% molybdenum. Fifteen percent of the total copper head exists as nonsulfide mineralization.

Jan 1, 1985

By R. Pandey, G. Elie, E. Sarver

Respirable crystalline silica (RCS) is generally considered the most hazardous constituent of coal mine dust, and a new federal rule is expected to further limit exposures in U.S. mines. For regulatory purposes, RCS is monitored by collecting filter samples, which are analyzed for quartz (the predominant form of RCS in coal mines). The analysis is done using Fourier transform infrared spectroscopy (FTIR) in a centralized laboratory. To enable more timely results, National Institute for Occupational Safety and Health (NIOSH) mining researchers developed a directon- filter (DOF) FTIR analysis method and free FAST software that can be used in the field. For samples collected under specific conditions, FAST processes the FTIR spectral data to determine quartz mass. While the DOF FTIR method is not approved for regulatory RCS monitoring, it could be useful for engineering purposes, such as to evaluate mining parameters or new dust controls. This field study demonstrates how the method, including FAST, can be applied using low-cost, widely available sampling components. It further demonstrates how quartz percentage can be estimated in the field, by pairing a continuous personal dust monitor with a filter sampler.

Jun 1, 2025

By R. E. Scheffel

In February, 1976, Ranchers Exploration and Development Corporation obtained an option from Foote Minerals, Inc., to evaluate reprocessing of two uranium tailing piles. Foote received ownership of the Naturita and Durango tailing piles in 1967 through the purchase of Vanadium Corporation of America. The option was exercised in November, 1976, after initial testwork proved that a viable extraction technique existed. Preparation for production at Naturita began immediately with engineering and en¬vironmental permitting proceeding simultaneously. Production began in December, 1977, just 22 months after acquisition of the property and-was completed 17 months later.

Jan 1, 1981

By S. Brummelkamp, G. Van Weert

Separation of minerals by shape has received little attention, since minerals normally do not break into different shapes during crushing and grinding. However, comminution of consumer wastes generates opportunities for novel separations based on particle shape. For instance, ductile plastics are broken into longer curved shapes, whereas brittle plastics yield angular particles. Using spouting beds for particle separation in water requires controlling the spout's instability. The preferred geometry for such redesigned spouting beds is reported. Plastic cylinders, discs and spheres were separated as a function of rising water velocity and amount of particles in the system. By using 5 mm particles, differences in settling behavior could be video recorded.

Jan 1, 1999

By Paul R. Kruesi

A patent-applied-for process has been developed in which zinc chloride is extracted by tributyl phosphate in kerosine, and stripped with ethylene glycol or ammoniated ethylene glycol. The anhydrous zinc chloride is precipitated from the glycol as the ammine and zinc chloride is prepared by thermal decomposition with recycle of ammonia. The process permits the production of high grade zinc from scraps and drosses. Its applicability to the recycling of zinc will be illustrated.

Jan 1, 1984

By S. Dixon

The Peñasquito deposit in Mexico is one of the largest grassroots precious metal discoveries to be developed in recent years Minera Peñasquito, S.A. de C.V., a wholly owned subsidiary of Goldcorp Inc. has developed the Peñasquito property to produce an average annual production of 120 kilo tonnes of lead containing 0.5 million oz gold and 30 million oz silver and 250 kilo tonnes of zinc containing 20 thousand oz gold and 1.5 million oz silver.. The Peñasquito property covers a 39,000 hectare area in the western half of the Concepción del Oro district in the northeast corner of Zacatecas State, Mexico, approximately 24°45'N latitude/101°30'W longitude. The sulfide reserves are 1,009 million tonnes containing 3.33 million tonnes of lead, 7.26 million tonnes of zinc, 16.5 million ounces of gold and 1,000 million ounces of silver. This paper describes the work to justify the installation of HPGR to process the crushed SAG mill pebbles. The SAG mill-Ball mill and Cone crusher (SABC) grinding circuit is an accepted grinding circuit to optimize power consumption relative to throughput. The installation of a HPGR to process the Cone crusher product is the next step in optimizing the power consumption relative to throughput. The concern expressed by some on not moving on this change in grinding circuit was the capital and operating cost of a HPGR. The pebbles from the SAG mill can be the more abrasive and are the harder particles of the ore. Goldcorp investigated the wear and processing costs of installing a HPGR to treat the crushed pebbles. The conclusion was the installation would be a very positive economic factor in the operation of Peñasquito. This is the first application of the use of HPGR to process crushed pebbles. Minera Peñasquito and M3 Engineering selected Polysius to provide a Polycom 2417 with twin 3,000 kW drives. A comprehensive test program at Polysius has shown for 7% higher circuit power it is possible to get approx 23% higher tonnage. This coupled with full utilization of the SAG and Ball Mill available energies and with proper control of the transfer size from the SAG to Ball mill circuit there is the potential to achieve 65,000 mtpd per line or a 30% total capacity increase. The cost of power for this increase in grinding capacity is 4.8 kWh/tonne.

Jan 1, 2010

By T. R. Ellis

A number of important international events took place in 2001 in the development and evolution of mineral valuation standards internationally. In Canada, the CIMVal Committee released a draft discussion paper for public and industry comment on principles to guide the development of the planned Canadian mineral property valuation standard. The International Accounting Standards Board (IASB) received comments on its Extractive Industries Issues Paper. IASB will decide whether the financial statements of public mining and petroleum companies will be allowed to provide the value of mineral and petroleum assets on a current value basis instead of an historic cost basis. The author led the Extractive Industries Task Force of the International Valuation Standards Committee (IVSC) in developing its submission to IASB. IVSC intends to develop an extractive industries valuation section for its International Valuation Standards, which could support the planned IASB standard. In Australia, AusIMM has carried out an in-depth review of its highly regarded VALMIN Code. The AusIMM's MICA subdivision organized the VALMIN ‘01 Conference in Sydney, Australia, with a range of international and current issues papers published in the VALMIN ‘01 book. Considerable support for the IVSC initiative was evident at this conference. The results of the review of the extractive industries submissions to the IASB are expected to be released in early 2002. The CMMI Congress in Cairns, Australia in May 2002 is likely to prove to be an important forum for continued discussion of the development and implementation of international standards and qualifications for mineral valuation. The outcomes and implications of these events are discussed.

Jan 1, 2002

By M. J. Gula, S. S. Xue, E. P. Horwitz, J. T. Harvey

A study has been conducted to control iron in copper electrolyte streams using Eichrom Industries’s new Monophosphonic /sulphonic acid resin. The resin strongly and selectively extracts ferric ion over copper and cobalt from highly acidic copper electrolytes. The resin has a loading capacity of 27 g/L of iron and can be readily regenerated. In addition, the new resin can be easily synthesized using commercially available starting materials. This paper presents the experimental results for iron control in copper electrolyte streams using the new resin and discusses its potential applications to other hydro-metallurgical streams.

Jan 1, 2000

Draglines are one of the largest land-based equipment moving across the earth. They typically ranging in size from2.5 to 6.5 kt (2,750 to 7,100 st). Their size, though, makes them difficult to maintain. Recently, G&S Engineering Services used an Enerpac synchronous hydraulic lifting system to lift a 3.2-t(3,500-st) dragline at the Curragh Mine in Queensland, Australia’s Bowen Basin.

Jan 1, 2004

By Zoheir Khademian, Morgan Sears

According to the 2010–2019 Mine Safety and Health Administration (MSHA) accident report database, 91% of reported ground control accidents in US longwall mines were caused by roof instability. Gateroads are subjected to significant changes in loading conditions from the development to the longwall abutment loading phases. When combined with thinly bedded shale roof, found in many US longwall coal mines, the design of efficient roof support becomes challenging. In previous work, the bonded block modeling (BBM) of roof by UDEC was validated against field extensometer measurements in a longwall entry roof at a 180-m depth of cover. The BBM was shown capable of capturing delamination and buckling of shale roof, one of the main roof instability mechanisms in longwall mines. This paper presents the recent findings on the roof-support interaction using BBM models of the same longwall entry. The effects of cable bolts, roof bolt density, and strap support on potential roof instability are studied. Results demonstrate the potential for BBM numerical models to help understand the complex roof and support system interactions and to assist with optimizing gateroad support systems.

Feb 13, 2024

By S. B. Patton

To fully utilize a ventilation simulator as a planning and production tool, the network database must keep pace with mining progress. By using AutoCAD's attribute-definition function, the branch data and node coordinates can be stored as part of the branch-diagram file, and updated with the drawing. Attributes are drawing entities that contain text which can be extracted in a standard spreadsheet format or as an ASCII text file. The data can be subsequently loaded into a ventilation simulator with plotting capabilities, such as VNETPC. This paper presents the methodology for using AutoCAD's attribute feature in a ventilation simulation.

Jan 1, 1994

By H. E. Cross

In a minerals-recovery context, the object of exercising control over milling operations must be threefold, 1) To achieve maximum recovery at 2) minimum operating costs and 3) making maximum use of installed equipment, Milling is one of a sequence of operations which have as their objective the economic recovery of minerals from mined ores, All operations in the sequence are interdependent and each is both influenced by and itself affects all other unit processes. The part which grinding plays in achieving each of the above objectives is indicated in the following analysis: In South Africa, the most important mining operations are still the gold mines, A vast reservoir of knowledge and experience in treating the Witwatersrand and associated ores has been accumulated. and recoveries are consistently high, However residue values do vary and frequently this is due to fluctuations in the degree of grind, The significance of changes in residue values is indicated by the following example: On a modern mine, the residue values varied from 0,25 to 0,33 dwi; per 2000 lb, during a period of 6 months, The cash value of the gold thus lost varied therefore between $0.44 and $0.58 per 2000 lb, ton. A residue which assays 0.30 dwt per ton would contain approximately 0.26 dwt as undissolved gold and 0,040 dwt per ton as dissolved gold present in residual solution after filtration. This dissolved gold loss is a function of efficiency of filtration and varies from 0.030 to 0,.070 dwt per ton of residue.

Jan 1, 1970