Search Documents

By A. Cartwright, J. Cardwell

"Complex geology requires innovative approaches to confidently and appropriately model grade and geologic trends. Local Anisotropy Kriging (LAK), by Isaaks and Company, and MineSight® Dynamic Unfolding (MSDU) from Hexagon Mining are advanced interpolation methods designed to best estimate grade along deformed three-dimensional grade trends at sediment-hosted deposits. While LAK works in Euclidean space for the construction of variograms, kriging weight assignment, and non-linear local interpolation search ellipsoids, MSDU is far more dynamic and can utilize a modeled three-dimensional undulating surface representing a folded grade trend to construct the above mentioned. MSDU was implemented at the sediment-hosted, stratabound Tenke-Fungurume mining district and revealed major block-to-block differences in interpolated copper and cobalt grades compared to LAK. INTRODUCTION Grade estimation is the cornerstone of long-range mine planning. Pit designs, metal recovery, mining costs, reserves calculations and reporting are all dependent upon a reliable grade model. If the geology is poorly understood or the interpolation methods and parameters have been haphazardly constructed, then massive financial losses will be the inevitable outcome. Therefore, a properly trained geologist must use all of the appropriate tools available including deposit knowledge and advances in modeling technology to construct the most geostatistically and practically sound long-range block model. Certain deposits, such as the sediment-hosted deposits at Tenke-Fungurume, require an interpolation method that best suites the style of mineralization. In 2014, Hexagon Mining developed a tool in MineSight called dynamic unfolding (MSDU) that has the potential to improve upon previous Euclidean-based interpolation methods. MSDU utilizes the non-stationarity of a folded grade trend to more accurately construct variograms and improve interpolation results based upon a modeled three-dimensional surface. Geology Overview The sediment-hosted Tenke-Fungurume mining district is located in the southeastern part of the Democratic Republic of the Congo (Figure 1). The rocks within the district are primarily dolomites and shales from the lower half of the Roan Supergroup that were mineralized by ascending pregnant copper and cobalt rich brines within a massive sedimentary basin (Cailteux et al., 2005) (Figure 2). These oxidized brines likely found a fluid channel in the porous RSC unit. The surrounding rock units provided a redox boundary for copper and cobalt precipitation along organic rich beds, forming a massive stratabound deposit that was later broken up by several subsequent tectonic events (Dewaele et al., 2006). Layering and Block Orientations To capture the bedding-controlled nature of the Tenke-Fungurume copper and cobalt mineralization, each lithology type must be subdivided into individual layers with a uniform thickness (Figure 3). The thickness of each layer is determined by the user, but should equal the bench height to achieve maximum resolution within each lithology type. Composites are back coded from the model to achieve layer codes that match block locations."

Jan 1, 2016

By John C. Nixon

In 1959, The Australasian Institute of Mining and Metallurgy (Aus. I.M.M.) was asked by the Federal Government of Australia and the State Government of South Australia to join in the formation and management of a new contract research organization which was subsequently named The Australian Mineral Development Laboratories (Arndel) ? This body was formerly the Research and Development Branch of the South Australian Department of Mines which had been set up to develop the Radium Hill uranium deposit. It had then gone into contract R&D and the State felt that it would be more appropriate for the Branch to become a separate national organization. The Aus. I.M.M. decided that a professional institute could not participate directly in Arndel and, as there was no other suitable industry group to do so, it formed the. Australian Mineral Industries Research Association Limited (AMIRA). AMIRA held its first Annual General Meeting in September 1959 when the first Council was elected and the Memorandum and Articles of Association were adopted. The initial task of AMIRA was to raise guarantees of work or cash from its members to underwrite Arndel for the first five years of operation. The Federal and State Governments also provided guarantees and Arndel commenced operations in January 1960.

Jan 1, 1977

By M. J. DeMarco

Beginning in late 1985 and continuing through 1987, Bureau of Mines personnel investigated longwall chain pillar and entry design in two-and three-entry gate-road systems at a deep underground coal mine located in central Utah. To evaluate their respective stability characteristics, four chain pillars and two longwall panels within the two separate entry systems were instrumented with Bureau of Mines hydraulic borehole pressure cells to continuously monitor vertical and horizontal pillar and panel stresses through adjacent panel retreat. In addition, supplemental entry closure information was obtained from sites located in the vicinity of the instrumented pillars. The findings presented in this report demonstrate the practicality of evaluating mine pillar stability using in situ methods and support three significant conclusions regarding ground control aspects of the investigated two-entry system: (1) Total areal entry loading was considerably less for the two-entry system, as opposed to the three-entry system, (2) a smaller percentage of opened ground in the two-entry system contributed to a marked reduction in roof falls, and (3) lower areal loading in the two-entry system suggests improved ground conditions when mining the underlying seam.

Jan 1, 1988

By R. G. Robins

The dissolution of metallic copper powder in aqueous solutions of cupric sulfate with ethylene under low pressure was investigated. The reaction stoichiometry obtained was:

Jan 1, 1988

By M. M. Botz

Cyanidation tailings which are disposed in a surface impoundment experience a loss of cyanide due to natural degradation, frequently reducing the cyanide concentration to very low levels. Quantifying cyanide losses in terms of pond geometry, local weather conditions and feed solution chemistry has been largely empirical though in many cases mining operations rely on surface impoundments to reduce cyanide to below an internally regulated concentration or an effluent limitation. To permit a more quantitative evaluation of cyanide losses in an impoundment, a computer simulation was developed to estimate the losses of free, WAD and total cyanide due to dissociation, photolysis and volatilization. Results of the model are compared against data collected for a North American tailings impoundment during 1998.

Jan 1, 1999

By D. R. Nagaraj

Editor&apos;s note: Minerals concentration is a disparate area, one involving many disciplines. Flotation, flocculation, reagents, microbial processes, gravity and magnetic separation, and the areas of coal and oil shale - concentration is relevant to all of these. In his article, Nagaraj reviews the latest developments and findings in concentration that have ocurred during the past year. Flotation The Monograph Series "Development in Mineral Processing," (Elsevier, 1985) was devoted to "Flotation of Sulfide Minerals." This volume has 26 articles covering the aspects of flotation chemistry, process development, plant design and equipment, and modeling and process control. The numerous articles on sulfide flotation had one recurring theme - the role of electrochemical processes and redox potentials in flotation and depression. Significant advances have been made in this area. A differential desorption-reflotation process was developed for the beneficiation of calcitic phosphate pebble (Hsieh and Lehr, Industrial Engineering and Chemistry, 1985). The carbonate and phosphate minerals were first separated from silica using fatty acid and the modifiers diphosphonic acid and HF. The collector on phosphate was then desorbed using sulfuric acid, and calcite was selectively floated without additional collector. A two-stage conditioning - initially at pH 10, followed by that at pH < 4.5 - with sodium oleate was developed to improve the separation between apatite and dolomite (Moudgil and Chanchani, Minerals and Metallurgical Processing, MMP, 1985). Separation of Mussorie rock phosphate in India from gangue calcite, dolomite, silicates, pyrite, and carbonaceous impurities was achieved with a three-stage flotation only on -75 µm (-200 mesh) fraction (Vaman Rao et al., International Journal of Mineral Processing, IJMP, 1985). The separation of fine SiC whiskers from other products of coked rice hulls by immiscible liquid and froth flotation was achieved using M1BC, pine oil, and mineral spirits (Parekh and Goldberger, MMP, 1985). Flotation was more economical. The carrier flotation separation of hematite fines from quartz fines was effected using coarse hematite as a carrier and oleic acid and ferric chloride (Cristoveanu and Meech, CIM Bulletin, 1985). Potash recovery from brines by laboratory-pan solar evaporation and amine flotation was discussed by Foot and Juiatt (Salts and Brines &apos;85, Proceedings, 1985). Flotation in a 45-kg/h (99-lb per hour) unit recovered more than 95% of the potash in schoenite and sylvite concentrates containing 28% and 62% K2O, respectively. The effects of fresh concrete into cement and aggregate by a single-step flotation process in aqueous suspension was described (Naegle, Chemical Engineering Science, 1985). The physico-chemical principles for the selective separation of proteins from mixtures using flotation were discussed by Ostermaier and Dobias (Colloids & Surfactants, 1985). Selective flocculation of hematite from silica was studied by Bagster and Mcllvenny (IJMP, 1985). Selective flocculation was more favorable with more highly charged anionic polyacrylamides and with high molecular weight. The cationic and non-ionic polymers flocculated both minerals. In minerals mixtures, there appeared to be very little selectivity unless a combination of dispersant and electrolyte was used. The effect of dissolved minerals species, such as Cu, Fe, and Ni on flocculation of chalcopyrite, pentlandite, millerite, pyrrhotite, and covellite was studied by Acar and Somasundaran (SME-AIME, 1985). Reagents There were some major advances made in reagent development for the minerals processing industry. Cyanamid introduced several classes of collectors, one of which - the diaryl monothiophosphates as acid circuit col¬lectors of sulfides and oxidesulfide ores - was commercialized in 1985. The monothiophosphates are more stable and powerful collectors than the xanthates and dithiophosphates. Hydrolyzed dithiophosphate containing 80% monothio and 20% dithiophosphate was found to give optimum recovery of copper from crude cementation precipitate and separation of Cu and Ni sulfides from matte (Akimova et al., Obogashch, Tonkov, Rud, OTR, 1985). A new class of O-alkyl-Nallyl

Jan 9, 1986

By Roman Z. Pyrih

Subsurface migration of cyanide is attenuated by naturally occurring geochemical and biogeochemical processes. Geochemical mechanisms which remove or immobilize cyanide and metal-cyanide complexes include precipitation/coprecipitation, sorption, and volatilization. Geochemical properties of soils and geochemical materials that promote the functioning of these mechanisms include the following: 1) acidic soil pH; 2) presence of illite and smectite clays; and 3) presence of iron hydrous-oxides and organic carbon. Naturally occurring soil microorganisms play perhaps a more important role in attenuating cyanide movement than previously realized. Biodegradation of cyanide is a "renewable" process, limited in its effectiveness by the avalibility of oxygen and micronutrlents (usually phosphate) to the microorganisms.

Jan 1, 1990

By James P. Rider

Significant advances in longwall mining technology and equipment have occurred over the last decade by the late 1990s, longwall mine output accounted for 40% of all underground output in the U.S. and today longwall mines account for approximately 50% of coal produced underground in the United states. A 51% increase in average shift production rates has occurred over the last 15 years. this increased longwall productivity has meant that far more dust is being produced and controlling respirable coal dust presents an ongoing challenge for coal mine operators the National Institute for Occupational safety and Health (NIOSH) conducted a series of benchmark surveys at longwall operations across the country to identify current operating practices and the types of controls being used. Gravimetric and instantaneous dust sampling was completed to quantify the dust levels generated by major sources on the longwall section and to identify different control technologies in use today substantial reductions in dust levels were realized at sampling locations on the face when compared with ongwall surveys conducted in the 1990s results from the underground dust surveys and current longwall dust control technology and operating practices will be discussed. Mining Engineering, 2011, Vol. 63, No. 9, pp. 74-80. Official publication of the society for mining, metallurgy and exploration, Inc.

Jan 1, 2011

By Joseph B. Novak

In the last decade or so, the importance of effective preventive maintenance controls and practices has taken on a new and accelerated emphasis. Advances in technology and changes in equipment and product designs impose more precise and demanding standards of quality, productivity and customer service at a very rapid pace. Daily, it is becoming more apparent that in order to fulfill current requirements, existing manufacturing practices and associated control programs must also be upgraded and expanded. This is particularly true in the field of maintenance services. As production and quality standards become more demanding, effective equipment maintenance takes on more importance and becomes more difficult to sustain. In modern plants, the failure of a single equipment component can shutdown a complete production line causing interruptions to operating and shipping schedules that result in costly downtime, dissatisfied customers, and reduced profits. These costly experiences can be minimized with an effective maintenance program that provides maximum equipment reliability and minimum downtime and readily adapts to revision and change. A significant feature of an effective program is the provision of controls over activities generally identified as

Jan 1, 1971

By Wilfred Walker

A working hypothesis is presented herein mineral belts are split as all world oceans opened. Rather than plate tectonics, expansion is favored as the most recent expression of the sequence of convecting systems in the Earth&apos;s mantle. Throughout the geological record this sequence has produced similar mobile belts. This similarity lends itself to both stratigraphic classification and the theme of mineralization in mobile belts demonstrated by Y. A. Bilibin. Crustal evolution should, therefore, serve as an important guide in understanding Pacific mineral belts.

Jan 1, 1982

By Albert J. Shohet

The increasing scarcity of bentonite coupled with the potential of improved pellet strength have created a need for understanding the effects of thorough bentonite dispersion in taconite concentrate. It has been known for more than a decade that under certain conditions substantial savings of bentonite are realizable by using thorough mixing of bentonite as compared to poor mixing. Extensive work done by J. O. Zetterstrom l at the Univer¬sity of Minnesota indicated the effect of thorough bentonite mixing in a controlled laboratory testing. Commercial hardware was not available at the time Zetterstrom1 paper was published and not much work was done until R. L. Stone, J. M. Karpinsky2, did work with Muller mixing. Nabush 3 worked with the pugmill principle, and Hoogovens 4 and Robe River 5 used the fluidized bed principle. It was very hard to convince iron ore industries to improve the mixing of Bentonite and taconite for the following reasons: A. The initial capital investment for improved mixing equipment; B. The relatively low bentonite cost a few years back, which was not enough to justify new equip¬ment investment;

Jan 1, 1976

By T. Kelly

The Cannon Mine is located in Chelan County, near Wenatchee, Washington, at the eastern foot of the Cascade Mountains. The mine is situated about two miles from the Columbia River, in the arid Columbia River Valley. Two hydroelectric dams provide electricity for the area, the Burlington Northern Railroad has a switch yard and loading facilities in Wenatchee. Approximately 25,000 people live in the area. The principal industry is fruit farming. Underground mining techniques are used to provide feed for a 2,000 tpd flotation concentrator at the site. The techniques are low- cost, high productivity methods which allow for a high extraction rate along with a high rate of recovery of the minable reserve.

Jan 1, 1986

By W. J. D. Stone

Many of the common valuable minerals have a magnetic susceptibility which is sufficiently high to render them amenable to magnetic separation. In addition,, many minerals which form the unwanted constituents of an ore can be removed by magnetic means. Magnetic separation in general has suffered seriously from, the lack of a high intensity wet separator. It is only recently that such a separator has become available to the industry. Prior to this, high intensity magnetic separation has been limited to the use of the dry techniques. Since the introduction of the Jones Wet High Intensity Magnetic Separator, extensive test work has been conducted to investigate possible applications. From the investigations conducted and the discussions that have taken place in the industry, it is apparent that the important mineral characteristic of magnetic susceptibility is not receiving the attention that it deserves. Applications for high intensity wet separation are being found in areas hitherto not considered.

Jan 1, 1963

By Ken Santini, Ronald R. Bauer, Joseph R. Copeland

Wollastonite, named after W.H. Wollaston, an English chemist and mineralogist, is a calcium metasilicate having the chemical formula CaSiO2. Although it is a unique mineral, wollastonite has a short history of industrial use. Wollastonite is the only naturally occurring, nonmetallic, white acicular mineral. Its acicularity is the main reason for its ascendancy in the late 1970s and 1980s as a reinforcing filler and as a replacement for short-fiber asbestos and short-fiber milled fiberglass. Wollastonite is used in applications ranging from bowling balls to automobile fenders, from ceramic tile to automobile brakes, and from thermal insulation board to protective industrial coatings. The United States is the largest producer of wollastonite, with China, India, and Finland as the other three major sources. The United States, Europe, and the Far East are where most of the production is consumed. Geology Mineralogy and Physical and Chemical Properties Wollastonite, a member of the pyroxenoid mineral group, has the theoretical composition of 48.3% CaO and 51.7% SiO2. Iron, manganese, magnesium, or strontium may substitute for some of the calcium. Commonly associated minerals include garnet, diopside, calcite, quartz, epidote, apatite, and sphene. Some of the physical properties of wollastonite are listed in [Table 1]. Wollastonite is largely chemically inert; however, it can be decomposed in concentrated hydrochloric acid. Some wollastonite will fluoresce under shortwave or longwave ultraviolet light, or both, with colors ranging from pink-orange to yellow-orange and, more rarely, bluish green. In addition, wollastonite may show phos¬phorescence. Because of its unique cleavage properties wollastonite breaks down during crushing and grinding into lath-like or needle-shaped particles of varying acicularity. This particle morphology imparts high strength and is therefore of considerable importance in many of the markets for wollastonite. The acicularity of particles is defined by their length:width, or length:diameter, ratio (i.e., aspect ratio). Individual particles, even the smallest ones, commonly ex¬hibit an aspect ratio of 7:1 or 8:1 and have an average diameter of 3.5 gm. Low aspect ratio products (powder wollastonite, or milled grades) with 3:1 to 5:1 aspect ratios are used as general fillers, in ceramics, and in metallurgical fluxing. High aspect ratio products with ratios of 15:1 to 20:1 are used as functional fillers for rein¬forcing thermoplastic and thermoset polymer compounds and as a replacement for asbestos. The dry brightness and whiteness of wollastonite are also important in determining its suitability for certain filler and ceramic applications. When pure, the mineral is brilliantly white, but impurities may color it cream or gray. Brightness is determined by measuring the reflectance of finely ground powder against a stan¬dard that is assigned a brightness of 100. Magnesium oxide and barium sulfate are the two standards used. G.E. brightness, a term used in North America, refers to brightness measured with a Gen¬eral Electric reflectometer. Commercial wollastonite products usu¬ally have a G.E. brightness ranging from 85 to 95. The Hunter method is also used to measure the brightness of wollastonite. Loss on ignition (LOI), another important property in determining applications for wollastonite, is the amount of volatile matter driven off when the mineral is heated to 1 000°C. Com¬mercial wollastonite products have an ignition loss ranging from 0.5 to 2.0%. Wollastonite&apos;s naturally high pH of 9.9 (10% water slurry) is of major importance to its use in the coatings industry. Coatings formulators use milled grades as a pH stabilizer in interior and exterior PVA (polyvinyl acetate) and acrylic latex paints. There are two polymorphs of calcium silicate: wollastonite, a low-temperature form, and pseudowollastonite, a high-temperature form. Conversion of wollastonite to pseudowollastonite occurs at about 1 120°C and results in an increase in the coefficient of expansion and a color change. Pure white wollastonite may change to a cream tint or to various shades of red or brown. This color change is thought to be due to the presence of iron and/or strontium.

Jan 1, 1994

By B. A. Hancock

New permit discharge standards instituted at Hecla Limited?s Lucky Friday Mine required installation of water treatment plants to manage water quality at two outfalls to the South Fork of the Coeur d?Alene River. The 002 Outfall Water Treatment Plant (WTP) is a clarification-filtration plant for treating the combined mill and underground discharge water flows. Process optimization efforts were a significant challenge until the negative impact the exploration diamond drilling products had on the clarification process was identified and resolved. The products were being wasted directly to the mine water discharge system which was pumped to the surface WTP. Anionic soluble oil and polyacrylamide based products were causing TSS particle hydrophobicity and dispersion that greatly affected coagulation and flocculation response, resulting in excessive chemical usage and treatment control issues. This paper details how problems associated with the drill products negatively impacted the 002 WTP and how system changes, alternative product usage and treatment at the source resulted in more consistent plant performance.

Jan 1, 2011

By Richard C. Mayberry

Phosphate reserves have been and still are a controversial subject. Some published estimates are particularly conservative and have caused concern in government and political circles that southeastern phosphates are a dwindling resource. "Ores and ore bodies" are a function of economics that relate to a time/demand factor. The history of phosphates and other mineral commodities is one of mineral deposits (resources) ever becoming ore (reserves) via a long term logic based on price, supply, and demand factors operating through time and improved technology. Projections indicate that southeastern phosphates are sufficient for several centuries of operations at present production rates.

Jan 1, 1981

By Robert M. Dreyer

Thirty years ago it was possible to locate a quarry site for crushed rock for concrete aggregate by finding the nearest solid rock bluff accessible by road, But times have changed and the location of a quarry site to furnish crushed rock for concrete aggregate now has become rather complicated, Although both sand and gravel can be used for aggregate, this discussion will be confined to crushed rock in the regions around a metropolitan area. Let us assume that a consultant has been retained to advise on the desirability, and the possibility, of opening a new quarry within a given area. The problems are geological and ecological. Since the geological problems are simpler, they will be discussed first. Generally, the first step is to make a market study of competitive aggregate sources within the projected area. Assuming that the quality of aggregate to be sold by competitors as well as their mining costs will, within narrow limits, be the same, the problem becomes essentially a study of haulage costs from established quarries into the projected new area. Since haulage cannot be effected along straight lines and since each quarry operator may have different unit haulage costs, a map showing lines of increasing cost intersecting points on roads available for truck haulage radiating from competitive quarries can be rather complicated. Such a map, more-over, changes each time a new haulage contract is negotiated by a

Jan 1, 1971

By Jamal Rostami

Continuous miners (CM) are the most popular underground mining machinery in soft rock mining, playing a dominant role in the production of minerals ranging from coal to evaporites while finding increasing use in salt and potash mines. Along with the ongoing technological advancements in the mining industry and the underground equipment, new generation of CMs offer several new features that are designed to enhance their operational capabilities and production rate. In addition to new bits and bit holders, one of the areas of improvement is the cutterhead design through computer modeling and simulation based on the full scale cutting tests. This paper discusses the state-of the-art CM technology and development of the computer models for design analysis and performance estimation of CMs. The general approach used in the modeling, along with the results of field trials for several projects will be presented.

Jan 1, 1998

By Charles G. Weakly, Alan M. Lander, Pamela B. Zohar, Robert W. Leonardson

The cluster of gold deposits at the Goldstrike property is located in the Northern Carlin Trend in northeastern Nevada (Fig. 1). At many mature mining camps like Goldstrike, exploration innovation and success may wane with time. In this regard, sufficient exploration drilling was conducted in the area immediately north of the ultimate pit crest and under the final planned pit wall to test for a major deposit. No indications of large deposits were found, however, the majority of drill holes did intercept mineralization. Mining along the northern pit wall exposed significant structurally controlled ore-grade mineralization that had been missed by exploration drilling. In 2002 and early 2003, the mine geology group added reserves to the pit and improved the definition of underground resources by targeting specific ore-controlling structures within favorable stratigraphic units by utilizing relatively inexpensive horizontal RC drilling from the pit wall. The widespread occurrence of mineralization to the north of the pit was re-interpreted to be an indication of continuity of these mineralized zones. In January 2003, 70 feet of 0.332 opt Au at a depth of 710 to 780 feet was intercepted in a dewatering well. This intercept was significantly thicker and higher-grade than average for the area, which confirmed the existence of high-grade structural continuity, and helped secure management support for additional exploration. A timely and cost effective solution was needed to confirm the potential of the area. Immediate follow-up drilling on tighter grid spacing was rejected in favor of improving the geology model. Exploration across the property would benefit from an improved geology model, but to provide results in a timely manner, the area to the north of the Betze pit was chosen as a starting point (Fig. 2).

Jan 1, 2005

By Tony Treasure, Ian Ewart

The EMEW® cell has been developed to overcome a number of inherent limitations in conventional electrowinning technology, particularly the high cost and restricted process windows characteristic of conventional hardware. The EMEW technology has been widely demonstrated to achieve high performance for various metals under chemical conditions well outside the limits required for efficient operation of conventional cells. In particular application of the EMEW cell for recovery of silver offers significant operating and capital cost advantages over conventional Merrill Crowe technology used for cyanide based solutions. The cell also offers process advantages for direct silver recovery from nitric acid solutions. The performance of the EMEW® cell on silver cyanide solutions, producing high grade silver metal in a single step, is accomplished by providing a physical mechanism which presents metal ions to the cathode on a highly efficient and continuous basis. The simplicity of design and operation of the EMEW cell offers the following advantages for silver recovery from cyanide or nitrate based solutions: • High grade product in a single step. • Selective for silver over other metals in the electrolyte. • Wide operating concentration range (100,000 - 5ppm). • Ability of the cell to operated in a variety of acid or alkaline electrolytes. (Cyanide, Nitrate). • Simple liquor reticulation. • No pretreatment required - Clarification, deaeration or zinc dust. • High cmTent density and current efficiency compared to conventional electrowinning cell. • Modular design allows for flexible operation and production rate. • Pilot plant results using full scale cell result in accurate scale up design. • Easy/fast installation - cell banks are delivered pre configured with piping and wiring. • Enclosed cell minimizes corrosive vapor and liquid losses in the circuit.

Jan 1, 2000