Search Documents

By E. McCarthy

"INTRODUCTION Talc is a hydrous magnesium silicate with the approximate elemental composition 4MgO.3SiO2.H2O. It is one of the layered phyllosilicates (like kaolin and mica) but it differs from these in that it is relatively hydrophobic. This is due to its unique crystalline structure whereby a brucite inner layer is sandwiched between silica layers and the adjacent silica layers have no interlayer bonding other than van der Waals forces. This allows talc to be sheared easily along this basal plane, and the surface is covalent not ionic. Talc occurs both as a relatively pure material (>90% talc content) and in conjunction with many other minerals in proportions all the way from 1% to 90%. At lower concentrations, it is often considered a nuisance mineral when it occurs with base metals like copper, molybdenum or nickel or with precious metals like platinum or palladium. It floats readily with these materials and often is suppressed using guar gum or carboxy methyl cellulose which will absorb along the basal surface and make it hydrophilic. Alternately if the reduced ore is hydrophobic, like MoS2, then a partial oxidation of the sulfide will convert the surface to a hydrophilic oxide and the talc can be floated away in a separate step. Talc in grades from 20 to 90% has been commercially exploited in a wide range of pigment (paint and paper), material (ceramic, construction and cosmetic), reinforcing (polymers and composites) and functional (pitch adsorbent, lubricating agent) applications. Initially these tended to be local or regional markets, but eventually with certain higher purity grades, cosmetic, polymer and ceramic applications became valuable enough to be national and trans ocean markets. TALC FLOATATION PLANTS This drove the need for higher purity grades of talc and initially this need was met primarily by ore sorting. This works well for certain deposits with well crystallized talc lenses, but for ores, such as those from widely available ultramafic deposits, where the liberation size is closer to 100 microns, sorting is not effective. That drove the need for floatation and the first investigations were published by Clemmer and Cooke of the US Bureau of Mines in 19362. The first commercial floatation plant was installed in Johnson, VT by the Eastern Magnesia Talc Co in 1937. The circuit is shown in the schematic (Figure 1). The ore was an ultramafic, serpentine derived talc; mineralogy was about 55% talc, 40% ferroan magnesite and 5% oxides, sulfides and other silicates. The oxides include hematite and chromite, sulfides pyrite and gerstorffite and silicates chlorite, serpentine and mica. After crushing, the ore was dry ball milled and then air classified to remove minus 325 mesh fines. The coarse fraction was further classified to cut at about 100 mesh and the fines from this were the feed to floatation. The -325 mesh (about 15% of the ore) was sold as a paint grade and the plus 100 mesh (about 25% of the ore) was screened to make an asphalt backsurfacing grade."

Jan 1, 2018

By L. Adler

Existing classifications of mining and construction equipment have had major deficiencies. They often lack organization, balance, and have remained obscure. Particularly when proceeding to great.er resolution these deficiencies have proven crippling. By adopting "Classes", "Groups" f "Types" and "Kinds" at successive degrees of refinement, a "Taxonomy" is developed based on clear visual differentiation or on a "Morphology??. This symbiotic application, adopted from the Biological Sciences, yields clear, simple and unambiguous results. Supporting this effort are guidelines for easily and credibly sketching equipment which are also distinctive. Numerous illustrative examples are provided. Communications are improved and the engineer obtains a confident feel for the equipment at hand.

Jan 1, 1989

By William Gleason

With more than 20 major mines extracting copper, gold, coal, molybdenum and lime, Arizona is recognized as one of the better mining jurisdictions, not just in the United States, but in the world. However, that is not to say the road to production is always paved with gold, or in many cases, copper. Earning the license to mine in Arizona is a complex process with years of paperwork and permitting before the first tons of ore are ever processed. Now, get the federal government involved and the process becomes even more complex, and the path to production can become even longer.

Jan 1, 2013

By David J. Hatem, K. Bhattarai

Effective risk management in major subsurface projects involves ways to mitigate adverse impacts to final design and construction approaches due to changed subsurface conditions. An Early Contractor Involvement (ECI) collaborated with Observational Method will be an effective contractual tool to address risk developed due to encountering differing site conditions. Observational Method (OM) can further be supported with artificial intelligence (AI) technologies with automated data-driven decision-making features in risk mitigation and implementation of proper design and construction approaches. This paper presents collaborative applications of ECI, OM, machine learning, and risk baselining in risk management and productivity enhancement in tunneling projects.

Jun 23, 2024

By Charles B. Dugger

Sacrificial linings for grinding mills have been a necessary state of the art of mineral dressing since the inception of comminution. Long recognized as the final link in energy transmission from power line to ore, mill liners as a scientific endeavor have not expanded as rapidly as other branches of mineral dressing engineering. Several reasons for this technological lag are apparent. Typically in the past, labor intensive foundries were freely located geographically, at a time when transportation charges made up a significant portion of the casting cost. Alloying agents had not gained their current level of sophistication and were relatively inexpensive in the quantities required. Precise foundry controls were not economically justified, or totally understood. Coincidental to these elements, liner consumption per unit processed did not categorically contribute as a major cost item to the mill operator. Grinding equipment was small, and many times lining life exceeded that of the promoter. These unique conditions no longer exist. Ore dressing equipment has grown to meet modern mining demands. Larger processing facilities, utilizing fewer pieces of equipment, have replaced operations of the past. Emphasis today and tomorrow is on larger and larger equipment, with an eye on lower and lower unit processing costs.

Jan 1, 1979

By R. H. Bartlett

Hydrometallurgical processes for copper flotation concentrates avoid the S02 emission problems associated with smelting, but they require oxidation of copper to obtain solubilization during leaching. The resulting copper ions must be reduced to metal, which normally requires large amounts of energy or energy equivalent reagents such as hydrogen or iron. The conventional reduction method is electrowinning which is labor intensive and involves 35 to 40% of both the en-tire operating and capital cost of the better hydrometallurgical processes. Smeltermen are correct in criticizing the available hydrometallurgical processes for being more energy intensive than modern smelting processes. Clearly, there is considerable incentive to reduce the cost and energy required for reducing copper ions from solution. Furthermore, it is thermodynamically possible to do this using sulfur contained in the concentrate itself. In fact, the thermodynamic potential of oxidizing sulfur from S+4 to the S+6 state is greater than required to reduce cupric ion to metallic copper. (1) Realization of this potential in a practical process would significantly reduce the cost of hydrometallurgical processing of sulfide concentrates because sulfur would become a cost-free reducing agent. An apparently practical method is to use SO3 and HSO3 ions, obtained by ammonia scrubbing of SO2 from a concentrate roaster gas, to reduce leached copper to metal in an autoclave. This reduction step is the Jumau 1907 patent. (2) A series of steps including sulfite reduction constituting a crude flowsheet was suggested by Parker in 1976(3), but apparently little development work has been done by him, since he has been interested in new routes of refining the resulting copper powder. The purposes of the present paper are to elaborate on the Jumau-Parker thrust. Describe a detailed complete sulfite process flowsheet based on materials and energy balances, discuss the chemistry, and discuss further work that is required to develop this process. The results of the present paper are largely based on a synthesis of the steps using handbook chemistry. Process materials, utilities costs, and energy requirements are projected to be unusually low.

Jan 1, 1978

By D. Tepavac, S. Simmonds

"The high virgin horizontal in situ stress field in the Sydney Basin and its impact on civil engineering projects is a well-known and accepted phenomenon found in significant literature (e.g., Pells, 2013). The prevailing high-stress effects depend on many factors — rock quality, tunnel orientation, proximity of geological features to tunnel crown, size and shape of opening, depth of excavation and stress magnitude. The behavior of the rock mass under high in situ stress conditions can cause stress fracturing and consequent dilation of the tunnel periphery, resulting in rock spalling at the tunnel crown/ invert or raveling of rock blocks on the tunnel sidewall. This type of failure is of a brittle nature and may create construction and safety risks during tunnel excavation, if it occurs behind the excavation face where ground support has already been installed. Therefore, the associated risks need to be managed during construction. This paper presents the design strategy adopted to mitigate these adverse tunneling conditions for the WestConnex Project to-date. Overview of the WestConnex M4 East and new M5 tunnel projectsWestConnex is one of the New South Wales government’s key infrastructure projects. This 33 km (20.5 mile) project aims to ease congestion and connect communities and is the largest integrated transport and urban revitalization project in Australia. It was a key recommendation of the State Infrastructure Strategy released in October 2012. It brings together a number of important road projects, which, together, form a vital link in Sydney’s Orbital Network. These road projects include a widening of the M4 east of Parramatta, a duplication of the M5 East, and new sections of motorway to provide a connection between these two key corridors. The WestConnex project includes a number of stages: Stage 1a: M4 Widening; Stage 1b: M4 East; Stage 2: New M5; and Stage 3: M4–M5 Link. The tunnel design referenced in this paper relates to Stage 1b and Stage 2 of the WestConnex Project (Fig. 1)."

Dec 1, 2018

By John Mastoris, Shkurta Gashi, Kostis Dragasakis, Kostas Kouklidis, Halil Berisha

Water is increasingly recognized as a critical issue for sustainable development, becoming as important as carbon to corporate responsibility and reputation. Although the cement industry’s overall ‘water footprint’ is relatively small compared to other sectors, the Cement Sustainability Initiative of the World Business Council for Sustainable Development (WBCSD/CSI) has recognized the importance of water and the need to take actions towards efficient water management, with developing standardizing practices and employing a risk-based assessment approach, mostly at local level where individual facilities and activities can have implications for other water users in the area. Sharrcem, a member of the Titan Cement Group, has made significant investments to upgrade its production facilities, the technological process and apply environmentally friendly technologies. Under this frame, Sharrcem implemented a project for the construction of a Waste Water Treatment Plant (WWTP) in the Cement Plant facilities, which has been successfully operating since early 2016. This paper discusses the technology applied at the new WWTP and the results achieved already, with significant improvement in the quality of the treated water, as compared to the previous situation where untreated wastewater was directly discharged to the nearby Dimce Stream. The WWTP project is a major investment of Sharrcem that aims to improve the quality of the discharged water effluents and thus prevent potential river pollution and overall protect the environment and the health of Sharrcem employees and local community. The WWTP operates with the Sequencing Batch Reactors (SBR) technology, is fully automated and has been also connected with few households of the neighboring community to treat also their sewage water. The plant can be expanded in the future – to connect with additional households - without increasing the size of the treatment tanks. One of the benefits of this project is that by removing a variety of contaminants from water it becomes usable again, depending on the nature of the contaminants and the end use of the water treated. According to the monitoring results the treated water that comes out of the WWTP fully meets quality requirements according to the EU and local limit values standards

Jan 1, 2017

By E. Woodburn, Harrison R. Cooper, R. Putman

The key to concentrator automation is practical means for obtaining continuous assay data from concentrator streams. The technique most successfully used is x-ray fluorescence analysis. The practical reality of on-stream x-ray analysis has been achieved through effort over the past twenty years, marked by an occasional breakthrough, but more typically a step-by-step development to which many individuals and organizations have contributed. The net result of this progress is the present capability to install on-stream x-ray analyzer systems on a turn-key basis. It is now possible to provide all components of an x-ray analysis system as a completely engineered unit which can be put into immediate use, minimizing needs for specialized application know- ledge to benefit from continuous assaying in process control. The economic factors which influence the choice of system and limitations of the x-ray fluorescence technique for slurry analysis are reviewed.

Jan 1, 1976

By Andrzej Walentek

This paper presents the results of numerical modeling of the fractured zone around longwall gateroads. The numerical computations have been based on the results of underground measurements of the fractured zone around longwall gateroads, which were performed for various geological and mining conditions and measured with the use of the endoscopic method with a digital camera. Having results of the underground investigations, trials of duplicating them by the Finite Element Method using software PHASE and the Hoek-Brown failure criterion were performed. In order that the fractured zone predicted by the model-based computations closely simulate that measured underground, some selected parameters in the Hoek-Brown failure criterion were modified based on the earlier determined relations used for prediction of the roof-to-floor convergence in longwall gateroads. As a result, the model-based computations produce results very close to those obtained from the underground measurements. Determination of the fractured-rock zone around the mine roads is of great importance to mining practice, especially in planning and designing supports for longwall gateroads. The influence of the front abutment pressure causes the fractured rock zone around the roads to increase and results in an increase of support load. Moreover, proper determination of the fractured rock zone is one of basic elements in the process of planning roof bolting for mine workings.

Jan 1, 2009

By K. V. Raj, C. A. Berry, A. T. Weakley, A. L. Miller, P. R. Griffiths, D. A. Parks

Diesel particulate matter (DPM) has been classified as a carcinogen to humans by the International Agency for Research on Cancer. DPM exposure is therefore regulated by the U.S. Mine Safety and Health Administration (MSHA). The current monitoring process takes days or weeks for exposure levels to be known, and a real-time monitoring device is needed. It is believed that infrared spectroscopy has potential for use in a real-time, field-portable device. This paper presents a method for measuring organic carbon (OC) and elemental carbon (EC) in DPM for a broad range of OC/EC ratios. 

By W. R. Boehme

The test work was done in two parts. In Part I, five 6 x 16 mesh activated coconut shell carbon samples made by four different manufacturers were evaluated as to their gold loading rate and total gold loading. The five carbon samples tested are not identified by manufacturer and are simply designated as Types A through E. Then from the carbons tested, a suitable highly active carbon was selected for subsequent studies on impurity effects upon loading, Part II. Test Procedures The procedures and tests descriptions are given for the ultimate gold carbon loading tests and the dynamic gold carbon loading tests.

Jan 1, 1983

By M. Deniz Turan, HASAN NIZAMOGLU, Z. ABIDIN SARI, Tolga Depci

Chalcopyrite extraction in an aqueous acid medium occurs through solid transformations into distinct intermediaries. As intermediates, mineral phases CuS, Cu2 S and Cu5 FeS4 may generate in the leaching solution before CuFeS2 completely decomposes to Cu2+, Fe2+ and S0. Oxalic acid is a common organic acid, and it dissolves easily in warm water. Due to the chelating feature of oxalic acid, it hinders iron precipitation by composing soluble complex anions in a wide range of pH. In this study, recovery of copper from solid material (obtained by leaching of chalcopyrite with oxalic acid in the presence of hydrogen peroxide) with a copper oxalate structure was carried out selectively using hydrochloric acid (HCl). Selective recovery of copper by degrading the copper oxalate structure with a low-solubility product (Ksp= 4.43 × 10 −10) was performed by conventional leaching in the presence of HCl.

By William E. Cobb

15.1 INTRODUCTION The mine development process, as discussed in Chapter 2, is a series of data gathering and analysis steps. As the mine development process proceeds, information about the geology, mineability, and metallurgy of a particular deposit is continually generated, along with environmental information regarding project permitting status. As data are obtained, checkpoint evaluations are typically conducted to determine the economic viability of the particular deposit. Although the project evaluation process was discussed at length in Chapter 2, a brief review of the process is presented here to "set the stage" for the discussion on economic analysis of heap leach projects. Figure 15.1 (MacKenzie, 1980) presents an overview of the sequential process of mine development. Once the deposit is discovered or acquired, an initial delineation program can be undertaken to expand the project's geologic, mining, and metallurgical data base. At the end of this initial program, the direction of the project is evaluated. The company can either abandon the project, postpone it, develop and mine it, or gather additional data in hopes of improving the project's economic viability. If the company continues gathering data, then another decision point and evaluation will be required. This process may continue until the company either decides to postpone the project or develop and mine it. A project may be postponed indefinitely, typically in hopes of improved metals prices. Certain holding costs, such as land or royalty payments, may be associated with postponement. In general, once a company goes through two evaluations, the project is less likely to be abandoned. For this discussion, it is assumed that the company will undertake initial, second, and third delineation programs to gather sufficient geologic, mining, metallurgical , and environmental data to justify a positive production decision from the second or third economic evaluation. The objectives of the first delineation program will be to confirm and expand upon the available information about the deposit. During the second delineation program, development funds should be directed toward identifying the critical project items (i .e., ore reserves, mineralogy, mineable grade, metallurgical recovery, etc.) that must be resolved before making the production decision. This second economic evaluation can be used to determine which metallurgical concept will be applied to the project: heap leach or a traditional agitation-type leach plant. If the proper work has solved key project concerns in the second program, a production decision may be made from that evaluation.

Jan 1, 1988

By A. T. Yu

Once exploration is complete, "winning" of the ore can be viewed as fundamentally a bulk handling proposition. Whether it is to strip, break, size, extract, load, haul, or even process, the success of each of these phases will depend upon how effectively one can utilize-the methods and tools that are available in bulk handling. Since as much as 30 to 60% of the total delivered price of raw materials can be attributed to handling and shipping (ref. 1), this expenditure may spell the success or failure of an entire mining venture. In fact, it has become increasingly evident that handling and shipping are so intimately associated with mining that only when they are duly considered throughout the mine-to -smelter master plan as an integral part of a total system can an optimum operation be expected and the most economical ton of ore obtained, this total systems approach should not only take in handling and haulage in and out of the mine, but also storage and transfer at the terminals (ref. 2,3,t), including ship and barge loading and unloading which are likewise a major consideration (ref. 5). Much has been developed during the past century in bulk handling, particularly in its expanding use in the mining industry. In view of the major role bulk handling has played and will continue to play in mining, in commemorating AIME's centennial, this paper will attempt to outline the state-of-the-art at this three-quarter point of the 20th century - one that is marked by its industrial revolution and rapidly accelerating technological advances. Bulk handling systems Although many developments in bulk handling are worth noting. The most significant during the past three-quarters of a century are: the total systems approach to solving problems, automation, the increase in speed and capacity.

Jan 1, 1971

By P. Davis

With new mineral deposits found in areas of difficult terrain, and annual production capacity increasing in mines over the last decade, the aerial ropeway is proving to be a viable, economic method of transportation from mine to processing plant. Of the more conventional designs, a bicable ropeway is more suited to difficult country than the simpler monocable. The bicable, however, does have limitations in the difference in levels it can accommodate in one section at a given capacity. This is noticeable where hilly terrain and high capacity imposes a limit on the length of each section. Increasing the number of sections for a relatively short conveying distance tends, in the case of conventional bicable, to unbalance the normally favorable economics of the ropeway. In addition to analyzing hauling rope stresses, other areas have to be considered when looking at high capacity ropeways. Bucket capacity, speed, and the wheel load on track ropes are examples. These and other factors led British Ropeway Engineering Co., of Sevenoaks, Kent, UK, to produce the twin-track system. Using twin track ropes, larger capacity buckets, and, if the height differential warrants, the installation of twin hauling ropes, BRECO produced a ropeway design for areas of hilly terrain and at higher capacities than had been considered suitable for aerial ropeways. Designs have been produced for systems handling 1.5 kt/h (1,650 stph), and the potential exists for expansion to above 2 kt/h (2,200 stph). The arrangement of ropes provides high stability of the cars and is especially suited to areas where high winds occur during normal operation. This development allows the aerial ropeway to be applied economically in difficult areas and at the increasingly high capacities demanded by engineers. Ropeway Transports Limestone to Sudan Cement Plant Maspio Cement Corp. of Atbara, Sudan, will soon use an aerial ropeway to deliver its entire limestone requirement 20 km (12 miles) from quarry to plant. The Atbara plant is located north of Khartoum, near the east bank of the Nile River. The quarry is west of the river, in hills rising from flat desert country. The original transport system was a 24-km (15-mile) railway from the quarry to the west bank and a monocable ropeway that crossed the Nile and continued to the fac¬tory, a distance of about 2.5 km (1.5 miles). This original ropeway had a capacity of 60 t/h (66 stph). With the extension of cement-making capacity in the late 1970s, 2.5 kt/d (2,755 stpd) of limestone was required and a new mono-

Jan 3, 1984

By J. Morris

Petro-diesel is a common collector for fine coal froth flotation but partitioning of diesel range organics (DROs) in process streams has not been widely studied. Preliminary research suggested that under normal dosing schemes total residual DRO in process waters should be limited to the sub-ppm water-soluble fraction (WSF). Further, polycyclic aromatic hydrocarbons (PAHs) should partition proportionately with DRO. The purpose of this study was to confirm these findings in laboratory flotation tests. Total DRO and specific PAHs were measured in tailings and concentrate streams, and coal recovery and ash rejection were tracked. Results show that concentrate waters consistently had higher DRO than tailing waters, and DRO in both streams generally increased with increasing diesel dosage. DRO again appeared to be limited to the WSF and PAHs tended to partition proportionately with DRO. Results indicate optimal flotation performance should generally coincide with minimal DRO partitioning to process waters. Under typical operating conditions residual DRO should not present an environmental concern; however, conditions should be avoided that allow significant overdosing of diesel.

Feb 23, 2014

By Klaus Rabensteiner, Klaus Chmelina

"INTRODUCTION Urban tunneling is often related with special geotechnical risks. Typical causes are difficult (hydro)geological conditions, a very low overburden and the presence of critical and vulnerable (infra)structures in the influence zone of the construction (e.g. existing tunnels, roads and pavements, sewer pipes, gas and power lines, landmarked buildings, historic monuments). To manage these risks appropriately, an early detection and warning of unexpected behavior of the affected geotechnical objects ground and tunnel, as well as existing structures are mandatory. To accomplish this, the design and execution of a dense geotechnical monitoring program is of high importance. In more detail, this means specifying and performing a systematic and continuous acquisition, processing and analysis of monitoring data to support decision making. In recent years the development of new automatic sensors and (wireless) data transfer techniques and the general trend towards an automatic acquisition of monitoring data has led to an enormous increase of data production frequencies and volumes. In order to handle this data explosion efficiently, information systems and geo-databases have been developed and used successfully in many projects. They represent IT tools that support the different tasks of a given geotechnical monitoring program including data acquisition, transfer, check, processing, backup, analysis, distribution, reporting and, last but not least, alarming. Meanwhile, some tools already have developed the capability to connect to other theme-specific databases used in the project and, thus, serve as a central data management system for all kind of digital data produced. This makes possible the implementation of further useful functions and services supporting tunneling tasks such as machine control, tunnel simulation, geological prediction, process optimization, etc. where data from different engineering disciplines must be combined and processed in an integrated way. In the following chapters our aim is to describe how monitoring data management, geotechnical monitoring, alarming and reporting are organized and technically implemented at the metro project Cityringen in Copenhagen (Denmark). We want to highlight the specific role and tasks of the used tunnel information system in the project, and particularly inform on the most relevant challenges."

Jan 1, 2016

By Andrew B. Cecala, Emily J. Haas, Jay F. Colinet

Researchers from the U.S. National Institute for Occupational Health and Safety (NIOSH) studied the impact of an unregulated dust control technology (the Helmet-CAM) and a regulated dust control technology (the continuous personal dust monitor) within a sociotechnical system (STS) framework to mitigate respirable dust sources. The results address how to best incorporate the overarching principles of meta-design STS during the technology integration process. Specifically, quantitative and qualitative data show that a prominent focus on the social factors within an STS framework could help reduce organizational unpredictability and may improve communication within the system to help reduce technology adoption time.

By ANA E. BOHE, MICCO GEORGINA DE, GASTON G. FOUGA, JUAN P. GAVIRIA, FEDERICO J. POMIRO

To the best of our knowledge, this paper comprehensively summarizes a thorough study to determine the thermodynamic viability of the reactions between light rare earth oxides and chlorine with and without carbon. The kinetics and mechanisms of light rare earth oxide chlorination and carbochlorination reactions are analyzed and discussed according to results in the literature. Lanthanides between lanthanum (La) and gadolinium (Gd) are considered as light rare earth elements (LREEs) in agreement with previous literature and the results detailed in this review. Both laboratory- and industrial-scale light rare earth chlorinations and carbochlorinations, starting from oxides and ores, are reviewed.