Search Documents

By Iga Trisnawati, Fitria Puspita, Himawan Tri Bayu Murti Petrus, Gyan Prameswara, Idi Amin, Andi Nurfaadhilah Ulfah

Laterite ores, rich in essential metals like nickel, iron and cobalt, are a crucial resource for modern technology. However, the extraction of nickel from laterite ores is a complex process due to their intricate mineral compositions and low nickel concentrations. This paper presents the results of a study to understand the leaching behavior of preroasted laterite ore and the impact of roasting on leaching kinetics. The ore was subjected to roasting at 280 and 610 °C for a duration of three hours, followed by leaching in sulfuric acid (H2SO4) under atmospheric conditions. The results show that preroasting the ore at 610 °C significantly improved the recovery of nickel during leaching, with recovery rate of up to 93 percent, and the leaching process of the preroasted ore was primarily controlled by diffusion through the ash layer. The activation energy values were found to be 20.97 kJ/mol for the ore roasted at 280 °C, and 18.97 kJ/mol for the ore roasted at 610°C. These findings suggest that preroasting can enhance the leaching performance of laterite ore, potentially paving the way for more efficient and sustainable nickel extraction processes.

Aug 1, 2024

By George D. Coumoulos

The following aspects of diasporic bauxite are discussed: The importance of world reserves of diasporic bauxites; the geological, chemical and mineralogical characteristics of the Greek diasporic bauxite; the uniformity of bauxite deliveries; the significance of the absence of organics; the excellent settling properties of the red mud; the production of sandy alumina from diasporic bauxites; the advantages of applying tube digestion systems in processing diasporic bauxites; the conditions for introducing diasporic bauxite in the existing European refineries.

Jan 1, 1984

By VÍCTOR VÁZQUEZ-VÁZQUEZ, GUILLERMO TIBURCIO-MUNIVE, María M. Salazar-Campoy, JESÚS L. VALENZUELA-GARCÍA, OFELIA HERNÁNDEZ-NEGRETE

This study examines a process for the recovery of precious metals from difficult minerals that exhibit refractory characteristics to cyanidation: low extraction of metals and high consumption of leaching reagent. A mineral sample from Monte del Favor Mine, located in Hostotipaquillo, Jalisco, Mexico, was physically and chemically characterized by X-ray powder diffraction (XRPD), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), fire assay and atomic absorption spectroscopy (AAS). Two stages of leaching were carried out, first to eliminate manganese from the sample using sodium sulfite (Na2SO3) as a reductive reagent along with sulfuric acid (H2SO4), and second to dissolve gold and silver with hydrochloric acid (HCl) and sodium hypochlorite (NaClO). The results show extractions of around 96 percent for manganese (Mn), 98.73 percent for silver (Ag) and 83 percent for gold (Au). The usefulness of high acidity and Na2SO3 to obtain better results in Mn and Ag leaching are discussed along with the roles that HCl and NaClO play in Ag and Au dissolution values.

By Patzen Wu

Taiwan is located in the orogenic belt of island arcs on the western rim of the Pacific Ocean. The structure of the Taiwan coal fields is much complicated as a result of active Cenozoic orogenic disturbance in Plio-Pleistocene time. The abundant faults and folds have created poor structural conditions of the coal seams and some peculiar safety problems in mining however, the domestic coal still played an important role in the economic development of Taiwan for the years before 1968. Because of increasing mining depth and a decreasing number of miners, the coal production dropped from nearly 5.1 million metric tons in 1968 to 2.45 million metric tons in 1981. There were 173 small active coal mines and about 22 thousand miners in 1981. The coal mining in Taiwan has a history of more than one century. Specific efforts have been undertaken in solving major coal mine safety problems such as gas outbursts, bad roofs and weak floors, difficulty in ventilation due to deep underground mining, spontaneous combustion etc. We have thus acquired much helpful experience which, we deem, is worth reporting at this meaningful meeting.

Jan 1, 1982

By Timothy P. Smirnoff, Anthony Stirbys, Amanda Elioff

The construction of the continuing expansion of the Los Angeles Metro System has required the construction of eight new station structures. One contractor proposed, as a construction alternative for the support of excavation of the Hollywood/Vine Station, the use of soil-mix walls instead of the conventional soldier piles and wood lagging. Soldier piles and shotcrete or wood lagging support systems had been generally used on the other sub-way station excavations constructed to date throughout the system. Immediately east of that station and in almost exactly the same geology, the Hollywood/Western Station was being excavated at the same time using a conventional support system. This paper com-pares the performance of these two support systems in the alluvial soils of the Los Angeles Basin.

Jan 1, 1997

By J. C. Gathje

The Robinson copper ores were mined for many years from pits containing varying ore grades, sulfide and oxide ore types, and differing mineralogy. The ores also contain gold and molybdenum values, and their recoveries are an integral part of the flowsheet development. Metallurgical responses were characterized using a standard flotation procedure. Further studies investigated primary and regrind particle sizes, reagents, and other variables. The metallurgical testing was supported by mineralogical studies. Results demonstrated a high degree of metallurgical success for flotation. Final copper concentrates ranged in grade from approximately 28 to 30% copper and copper recoveries were 89 to 95% based on laboratory and pilot plant data.

Jan 1, 1992

"A commercially available through-the-earth (TTE) communications system was evaluated at an active underground longwall mine in West Virginia. This TTE system uses electricfield (E-field) sensing to send text-based communications through two separate antenna arrays connected in parallel. Each antenna array is composed of interconnected, grounded metallic rods or other such structures. Two-way communication between subsurface locations was investigated in this study using various antenna configurations. This field study was conducted as a part of a larger multisite evaluation of available TTE systems in an effort to determine their operational sensitivities. IntroductionWireless, through-the-earth (TTE) communication technology is designed to achieve point-to-point communication through solid strata using very low frequency (VLF) and ultra-low frequency (ULF) electromagnetic waves. Using this approach, communications are established without the need for intermediary communications infrastructure. As a result, TTE systems have the potential to provide reliable, robust communications between surface and underground personnel. Exploration into the use of TTE technology for this purpose dates back to the 1920s (Jakosky and Zellers, 1924; Pittman, Church and McLendon, 1985), but U.S. permissibility requirements slowed the development of TTE equipment for widespread implementation (Durkin 1980; Pittman, Church and McLendon, 1985). One of the primary challenges in producing wireless TTE communications is the counteraction of signal attenuation when propagating through solid strata (Barkand, Damiano and Shumaker, 2006; Wadley, 1949). The long wavelengths of TTE transmissions make them well-suited for reducing the rate of attenuation. However, even when operating within the VLF to ULF range, the performance of TTE systems is still affected by geologic and anthropogenic factors (Geyer, 1973; Geyer and Keller, 1976; Geyer, Keller and Ohya, 1974; Jakosky and Zellers, 1924; Large, Ball and Farstad, 1973). Although commercially developed TTE systems have demonstrated the ability to communicate in a variety of conditions, their range and performance have been highly varied (Barkand, Damiano and Shumaker, 2006; Geyer and Keller, 1976; Geyer, Keller and Ohya, 1974; Ilsley, Freeman and Zellers, 1928; Jakosky and Zellers, 1924; Yenchek et al., 2012)."

Sep 1, 2016

By Michael Prince

"Managing slurry is a constant challenge for mining operations. Since slurries are not uniform, the challenge is complicated by varying rheology, velocity, temperature and pressure, all of which affect how the slurry moves through the pipeline and how destructive it is to the system it is flowing through. Picking the right equipment from the outset — the right size pipe, the right size pump and the proper valves for the application — allows mines to operate more efficiently. Better valve designs deliver multiple benefits — they can lower the cost of operations, reduce the amount of maintenance and associated downtime required and are better for the environment. Historically, modulating systems have used ball, plug and pinch valves to manage the flow of slurry, but each of these alternatives has limitations. Ball valves require ceramic lining in order to delay wear, and once a ball valve does wear, the entire valve must be replaced. Similarly, plugs in plug valves should be coated to perform in control systems, and whole valves must be swapped out upon wear. Pinch valves are expensive and only require replacement of the sleeve. However, sleeve replacement involves an extremely arduous process in which the valve is completely taken apart.Traditionally, designers have avoided using knife gate valves (KGV) in modulating systems because KGVs have not been able to hold up under the harsh operating conditions. The throttling that is required in some of these processes rapidly fatigues conventional KGVs, rendering them useless and in need of replacement. Fortunately, innovative design changes have the potential to change established views.Breaking new groundRecognizing the need for improved components, Victaulic took on the challenge of designing a valve that could withstand abrasive slurry systems for a much longer period of time. The first step in this process was to talk to miners, maintenance personnel, process engineers and operators in the field about the limitations of current offerings and then determine design specifications for an ideal replacement.Many of the responses to these inquiries were very similar and reflected challenges with current operations; the primary objective was to find a valve that would be lighter and cheaper than the valves currently in use. In theory, a lighter valve would be easier to replace, and since replacements need to be performed frequently, a cheaper valve seemed like the right idea."

Feb 1, 2019

By Robert A. Bauer

Two basic types of subsidence occur in Illinois: pit and sag / trough. Pits develop over mines less than 165 feet deep and where relatively incompetent strata are found over the mines. Sag subsidence is found over mines as shallow as 75 feet and more generally over mines of greater depths. The percentage of subsidence and angles of draw associated with sag subsidence appear to be controlled by the rock properties at each specific site. The percentage of subsidence and angles of draw are smaller where the sites are not affected by geologic structures. An investigation to determine if a time factor based on the time interval from the date of mining to the subsidence events has shown that simple correlations with time, percent extraction, average pillar stresses, and pillar dimensions is not evident in Illinois.

Jan 1, 1982

By G. Włoch, E. Rudnik

The oxide fraction of industrial zinc ash was characterized in terms of chemical and phase composition, leaching behavior in sulfuric acid solutions, and leaching thermal effect. The waste product contained about 68 percent zinc (Zn), 7 percent chlorine (Cl), 2 percent aluminum (Al) and less than 1 percent other metals, such as iron (Fe), manganese (Mn), calcium (Ca) and silicon (Si). It consisted mainly of zinc oxide contaminated with metallic zinc and zinc hydroxide chloride. The dissolution of metals from the zinc ash was determined for solid-to-liquid ratios ranging from 100 to 500 kg/m3, acid concentrations of 10 and 20 percent, and temperatures of 20 and 40 °C. The best result — 130 g/dm3 Zn(II) at 95 percent zinc recovery — was obtained at a solid-to-liquid ratio of 200 kg/m3, sulfuric acid concentration RI SHUFHQWDQGLQLWLDOWHPSHUDWXUHRI ƒ& 7KH¿QDOVROXWLRQVZHUHFRQWDPLQDWHGPDLQO\E\0Q ,, DQG)H ,,, ions, but the presence of cadmium (Cd(II)) and lead (Pb(II)) ions enabled electrowinning of zinc of about 99 percent SXULW\DWKLJKFXUUHQWHI¿FLHQF\RI WR SHUFHQW /HDFKLQJRIWKHPDWHULDOZDVDQH[RWKHUPLFSURFHVVZLWKUHDFWLRQ heat of about 520 kJ/kg

By W. H. A. Timm

Lake Dufault Mines, Limited, is located ten miles north of Noranda, Quebec. Following discovery of a copper-zinc orebody late in 1961, metallurgical investigations of diamond drill core were conducted by Lakefield Research Limited during 1962 and 1963. These were followed by pilot-plant tests in May and June of 1964, utilizing underground development ore. Milling operations commenced on August 16, 1964, and reached rated capacity of 1,300 tons per day by October 1, 1964 (Figure 1). Since that time, tonnage was gradually increased to a maximum of 1,400 tons per day and since January 1, 1968, gradually decreased to the present rate of 1,100 tons per day due to an increase in the hardness of the ore. The ore milled from start-up until January, 1968, was mainly massive sulphides, consisting of a complex mixture of iron, copper, zinc and minor amounts of lead sulphides with important associated values in gold, silver and cadmium (aver- age specific gravity 3.8). From January, 1968, until the present, the ore being processed is described geologically as a boxwork of sulphide stringers of chalcopyrite, pyrite and pyrrhotite and some local dissemination in siliceous rhyolite (average specific gravity 2.9) supplemented by the massive copper-zinc ore. The limited size of the orebody and the mining method employed (open stoping by blasthole and slash and bench methods) would have made grade control from the mine difficult and expensive. It was decided to try to cope with grade variations in the mill. The resulting rapid and wide swings in mill heads, hardness and specific gravity have presented many and varied challenges for the mill personnel.

Jan 1, 1970

By Jung-Joo Kim, Jong-Uk Kim, Turab H. Jafri, Han-Kyu Yoo

"INTRODUCTION Steel sets such as H-type and lattice girders are often installed in the tunnels before the hardening of shotcrete to ensure the stability of conventional tunnels in soft ground conditions. In practice, while designing the tunnels with the help of numerical analysis, steel sets are generally considered only as temporary support elements. Only a few studies propose the direct application of composite support in the tunnel design, based on large-scale experiments and numerical analysis. In order to assess the structural performance of the composite support consisting of shotcrete and steel sets, large-scale experiments were performed on two types of arch-shaped specimens by applying the combined effects of axial forces and bending moments. Based on the experimental results, numerical analysis was performed to assess the application of composite support in tunnel design. The crown settlement, axial forces, bending moments, and load distribution in the composite support were analyzed in the light of different structural patterns. LARGE-SCALE EXPERIMENTS USING COMPOSITE SUPPORT Preparation and Procedure of the Experiments The preparation setup as well as the organized procedure of the large-scale experiments using composite support is shown in Figure 1. An appropriate geometry of the specimens was selected by considering the standard cross-section of a two-lane highway tunnel in South Korea. Under the loading conditions meant to develop the axial forces and bending moments simultaneously, arch-shaped specimens were assembled with the ends of the specimens subtending a 60° arc angle at the center of the arc circle as shown in Figure 2. The fabrication of six specimens was completed in two groups based on the dimensions of steel sets, with the first group of three specimens being reinforced by H100 (No.1, No.2, No.3) and the other three by H125 (No.4, No.5, No.6). In order to reduce the voids on the boundary of the shotcrete and steel sets, concrete was casted over the steel sets instead of using shotcrete. The specimens were designed to incorporate the uniaxial compressive strength of 21 MPa. Shear keys and steel plates were installed at the ends of the specimens, so that shear failure could be avoided at the ends and the specimens could also be protected from detachment at the fixation. Translational and rotational movements at the ends of specimens were fixed."

Jan 1, 2016

By T. Qiu

"The purpose of this study is to investigate the effect of the dosage of sodium hypochlorite as activator on the flotations of depressed marmatite and depressed chalcopyrite, with a focus on activation-flotation kinetics. Four flotation kinetic models were applied to test data using 1stOpt statistical analysis software to estimate the relationships between the maximum flotation recovery rates for the depressed marmatite and depressed chalcopyrite, the flotation rate constants and the sodium hypochlorite dosages. Within the range investigated, the highest flotation performances of depressed marmatite and depressed chalcopyrite were obtained at 2.5 mL/L sodium hypochlorite with zinc recovery rate of 93.8 percent and 3 mL/L sodium hypochlorite with copper recovery rate of 94.6 percent, respectively, after four minutes of flotation. A second-order model with rectangular distribution of flotabilities gave the best fit to test data collected at various sodium hypochlorite dosages. For the highest flotation performances of depressed marmatite and depressed chalcopyrite, the respective equations of their flotation models were derived and presented.IntroductionCyanidation tailings are the solid residues generated by gold plants that use cyanide to extract gold (Lv, Ding and Qian, 2015; Zhang, Li and Yu, 2013). Because of increasing demand for gold, the Chinese gold industry has developed rapidly, with production amounting to 451.799 tons in 2014, an increase of 5.5 percent from 2013. Chinese gold production has been the highest in the world for eight consecutive years. As a result, more than 2.45 million tons of cyanidation tailings are estimated to be discharged into tailings ponds every year (Li et al., 2010; Lv, Ding and Qian et al., 2015; Wang et al., 2015; Zhang, Li and Yu, 2013; Zhang, Li and Yu, 2012), and approximately 300 million tons of cyanide tailings are stockpiled in China, with the potential to cause serious environmental pollution as well as death to wildlife (Adams and Lloyd, 2008; Donato et al., 2007; Hewitt, Breuer and Jeffery, 2012; Velasquez-Lopez et al., 2011; Stephen et al., 2009; Zagury, Oudjehani and Deschenes, 2004). Concerns over cyanidation tailings are not exclusively environmental but also economic, as tailings occupy considerable land area, and tailings storage facilities increase the production costs of gold enterprises (Donato et al., 2007). Tailings often contain other valuable metals such as zinc, lead and copper. For example, the cyanidation tailings of Gaoyao Hetai Gold Plant in Guangdong Province contain 2.5 percent copper (Cu), 0.31 percent lead (Pb), 0.23 percent zinc (Zn) and 15.36 percent iron (Fe) (Shi, 2008), and the tailings of Tianshui Gold Plant in Gansu Province contain 1.94 percent Cu, 5.96 percent Pb, 0.27 percent Zn and 24.62 percent Fe. Cyanidation tailings have therefore been increasingly viewed as a secondary resource rather than waste."

Jan 1, 2016

By J. Sidhom, W. Fourie

"As the mining industry continues to face difficult challenges the need to persistently focus on productivity and utilization of labor and equipment costs will intensify. With these challenges in mind, Komatsu is helping to bring mining performance and analytics to the next level.By evaluating underground haulage, a significant component of the room and pillar mining value stream, variables have been identified and sensitivities have been performed to show opportunities to balance and streamline throughput. As a result of applying operational excellence tools to the mining environment, Komatsu is seeking to optimize mining performances by limiting waste, simplifying the process, increasing productivity and machine utilization, as well as removing workers from harm’s way.These days it’s not enough to work harder; mines have to work smarter. Improving efficiency, reducing costs, increasing safety: these are no longer nice to haves, they are must haves.Starting with the best products and the right people is a first step, but then what? How do mines take their operations from average to being a top performer? By using operational excellence principles aimed at eliminating waste, simplifying processes, automating where possible and removing people from harm’s way.The fundamentals of operational excellence (OpEx) are based upon the process of define, measure, analyze, improve and control (DMAIC). DMAIC is an improvement cycle that helps with, for example, haulage optimization by: defining the issues and problems in the process as well as the areas of improvement; measuring and collecting mining operational data by time study and equipment monitoring system; analyzing through sensitivities and production modelling to determine root causes and then improving the performance and controlling the operation.Komatsu uses OpEx or lean principles inside its organization to drive efficiency, but it also helps its customers employ them to achieve new levels of productivity and safety.These same principles can be applied in most situations to streamline processes, improve operations and deliver value."

Jan 12, 2017

By ERIK C. WESTMAN, JESSICA M. WEMPEN, DALLAN J. COONS, WILLIAM G. PARISEAU, MICHAEL K. MCCARTER

Safe, efficient underground mining is dependent upon proper pillar sizing. Pillar sizing is typically based on a combination of observation of prior behavior, point measurements, theory and numerical modeling. The actual stress redistribution within a pillar, while assumed for many years, has rarely been imaged. Such imaging can help confirm whether or not theoretical and numerical modeling methods agree with actual conditions within a pillar. This research presents a case study from a longwall mine in the western United States. A two-entry, gate-road yield pillar in the headgate of the mine was instrumented with seismometers and convergence monitoring stations, and was monitored over a period of about six months as the longwall face approached the pillar. In this paper, the stress distribution imaged using seismic tomography is compared to the stress distribution expected from theoretical models, geotechnical measurements and numerical models. The tomography results generally agree with those proposed by theory, convergence measurements and numerical modeling results. The agreement of the methods provides validation for the theorized stress redistribution, and this study provides further evidence that tomography can indicate the redistribution of induced stress within a mined rockmass and is another tool available to ensure that mining is conducted safely and efficiently.

Aug 1, 2022

By J. Noll, E. Cauda, T. Barone, S. Vanderslice

Measuring diesel particulate matter (DPM) for underground metal/nonmetal mine compliance samples is done by collecting DPM onto quartz fiber filters and analyzing the samples via NIOSH method 5040 for elemental carbon (EC) and total carbon (TC). As part of the sampling train, two quartz fiber filters in tandem are housed inside an SKC DPM cassette that includes an impactor. The impactor segregates DPM and mine dust, and the second filter is used to correct for adsorption of vapor phase organic carbon (OC). Since the value of the second filter is subtracted from the first, the pre-existing carbon on the filter media for both filters needs to be comparable. In addition, the pre-existing carbon on the media should be low for accurate and sensitive results. However, there have been some reports of elevated OC on the filter media of the SKC DPM cassettes, which would cause the limit of detection (LOD) to be higher than reported at times. In this study, blank SKC DPM cassettes from different batches and with different expiration dates were analyzed to quantify the amount of carbon on the filter media and to determine the LOD and limit of quantification (LOQ) associated with these samplers. It was found that the organic carbon and total carbon on the media was about five times higher than quartz media used in samplers from other studies. The average TC on the blanks was 2.57 μg/cm2 with a standard deviation of 0.70, resulting in a LOD of 21 μg/m3 TC, 8-hr Time Weighted Average (TWA), and LOQ of 69 μg/m3 TC, 8-hr TWA, when using these samplers for collecting DPM. The LOD and LOQ may be improved through some sample preparation techniques. INTRODUCTION Exposure to diesel exhaust (DE) is associated with an increased risk for lung cancer and other adverse health effects (Attfield et al. 2012, Silverman et al. 2012, Ping and Guang 2017, IARC 2012). Pronk et al. 2009 reported that the highest exposed groups to elemental carbon (EC) from DE worked in underground sites in mining and construction and they were exposed to concentrations between 27–658 μg/m3. At concentrations (1–25 μg/m3 EC) well below those observed in mining, diesel particulate matter (DPM) exposures were estimated to increase the risk of cancer by levels exceeding those typically acceptable for occupational risk in the United States and Europe (Vermeulen et al. 2014). This suggests that underground miners are especially at risk because of their more substantial exposures in confined working spaces. As a protective measure, in 2001, the Mine Safety and Health Administration (MSHA) promulgated a rule to limit exposures of metal/nonmetal underground miners to DPM to an 8-hr time-weighted average (TWA) of 160 μg/m3 total carbon (TC) (MSHA 2001, 2006).

Jan 1, 2019

By Todd Burchett

Mining engineers spend countless hours and resources when designing a new underground coal mine. Their primary objective is to design the safest and most efficient operating mine with regards to coal production. A key variable often overlooked in this design stage is the slope conveyor. Typically, a slope conveyor is expected to operate with a 98-percent or higher availability. However, too often little effort is put forth by the mining engineer to optimize its design. Coal companies will rely on engineering, procurement, construction and management (EPCM) companies for the preliminary design, because the slope conveyor will be considered part of the surface material handling processes. This preliminary design will be used when soliciting quotations for the slope conveyor. Unfortunately, EPCMs may not have enough expertise with conveyors to optimize the design. This expertise is available with an original equipment manufacture (OEM) of conveyors, which ultimately may be responsible for supplying the slope conveyor. Each OEM will provide a bid package that represents what it considers to be the optimal design.

Jan 1, 2013

By Andrew L. Mular

Methodology to model, simulate and optimize full scale mineral pro- cessing circuits in production environments is reviewed and evaluated. Strategies for data acquisition and adjustment are considered along with techniques to fit models to adjusted data. Examples are considered for clarity.

Jan 1, 1989

By J. O?Hanlon

The 4500 m3 blast furnace at the Redcar Works of ESC operates or, a burden of sinter and pellets, both materials being produced within the works. The early history of the furnace was given to the AIME Ironmaking Conference in 1981(1) when the burden was 65% superfluxed minter and 33% acid pellets. While ironmaking performance was adequate, it was felt that there were advantages to be gained by the use of fluxed pellets. For example, Kobe Steel had reported (2) that the rise of 30-50% dolomite fluxed pellets had enabled them to achieve better furnace permeability, higher gas utilisation, and enhanced ore/coke ratios. It appeared probable to BSC that the use of magnesia-bearing fluxed pellets would give a burden which had compatibility of softening and melting properties, i.e., fluxed sinter and dolomite pellets would result in a thinner cohesive zone because of closer matching of softening and melting temperatures, with consequential benefits on furnace stability and efficiency.

Jan 1, 1983

By Gunjan R. Bhattarai, K. Bhattarai

Applications of machine learning and robotics in the tunneling industry are still nascent. Research and development are ongoing in TBM guidance; prediction of TBM cutter wear and tunneling induced ground deformations; and robotic arms for segment installation, inspection, cleaning, and maintenance of TBM cutting tools. This paper presents a case study of geological profile reconstruction using multimodal machine learning. The results from this study can aid the development and application of multimodal AI technologies to generate data reports and geological profiles in real time, taking voice recordings, photos, or videos obtained directly from the field as inputs.

Jun 23, 2024