Search Documents

By Robert W. Bartlett

Both hydrometallurgical and vapometallurgical processes often involve ores that have been previously ground and size classified. When the valuable mineral is substantially liberated, the chemical reaction is likely to occur on the particle surface and the particle core will shrink as the reaction proceeds. If the chemical reaction products are solid materials then a solid shell, usually porous, will form around the shrinking core. This is known as the core/shell or topochemical reaction model. Using a spherical approximation for the particles, equations have been developed to express the extent of chemical conversion of the particle, depending on which one of the following process or mass transport steps is rate controlling:1 (1) chemical reaction at the particle surface, (2) diffusion through the thickening reaction product shell or (3) mass transport through a boundary layer surrounding the particle. In a previous paper2 these equations were coupled with the Gates -Gaudin-Schuhmann equation 3 4 describing the distribution of particle sizes resulting from comminution of rocks and other brittle solids to develop reaction yield curves expressing the weight fraction of metal or other valuable component of the feed that was chemically converted as a function of residence time. This was done for (a) batch, (b) continuous plug flow and (c) continuous back-mix flow (continuous stirred tank) reactors or process vessels. To make the curves of general rather than special utility, the residence time (average residence time for back-mix reactors) was normalized to a dimensionless time by dividing by the time required to completely chemically convert the largest particle in the feed to reac-

Jan 1, 1972

By DEBASHISH MISHRA, SOMU MANDAL, ASFAR MOBIN KHAN, JAI KRISHNA PANDEY, NIROJ KUMAR MOHALIK, SANTOSH KUMAR RAY

Coal is a low-cost fuel with high calorific value. Statistically, the global coal mining industry suffered 12,489 fatalities in 104 reported mining accidents from coal dust explosions during 1900 to 2020. This review article discusses the occurrence, mechanism and explosibility parameters of coal dust explosions and presents a literature survey of the laboratory and computational fluid dynamics (CFD) simulation methods of studying them, as well as a comparison of the two methods.

Feb 1, 2023

By J. Sottile, V. Androulakis

Operators of underground coal mine shuttle cars are exposed to numerous hazards including noise, dust and musculoskeletal trauma. The repetitive nature of shuttle car operation leads to fatigue-related incidents and soft tissue injuries. The poor visibility conditions, and dust and noise increase the occupational hazards to the operator, as well to other miners. To reduce the risks for all miners, towards providing a safer working environment for all workers, the introduction of autonomous shuttle cars is essential. This paper introduces a project to demonstrate the feasibility of incorporating autonomous shuttle cars in the underground coal mining cycle. The autonomous shuttle car will be able to localize itself, to map its surroundings and to navigate in an underground GPS-denied environment. It will also navigate efficiently by fusing different on-board sensor modalities, autonomously planning the optimum path and traversing around the mine while avoiding collisions with humans and other static and dynamic obstacles. This will be achieved by exploring and testing different state-of-the-art techniques and off-the-shelf components, and integrating them into existing equipment, i.e., retrofitting an actual shuttle car. Moreover, a modified mining system will be demonstrated which will incorporate the autonomous shuttle car, capable of making real-time decisions, into the mining cycle. The system will regulate the interactions between the autonomous machinery and the human dynamic, with emphasis given to the safety of the workers, and enable the real-time, remote supervision of the mining process. The focus will be on coal mines, where the room and pillar mining method is used. INTRODUCTION The growing demand for mineral supplies combined with the steady decline in the available surface reserves has driven the mining industry to mine deeper underground deposits. These deposits are difficult to access, and the environment may be hazardous to mine personnel (e.g., increased heat, difficult ventilation conditions, etc.). Moreover, current mining methods expose the miners to numerous occupational hazards such as working in the proximity of heavy mining equipment, possible roof falls, as well as noise and dust. In recent decades, the utilization of autonomous machines has evolved in the mining industry to provide increased health and safety to mine personnel and reduce their exposure to adverse conditions. Automation aims to remove the workers from the hazardous conditions which may be present in an active mining area and place them to a more comfortable and safer environment at a distance from the active mining face. Examples of incorporation of autonomous machinery in the mining industry include the fleet of more than 100 autonomous mine trucks that are employed at the Rio Tinto’s iron ore mines in Western Australia for material haulage. There are also semi-autonomous, teleoperated LHD machines employed at several mines around the world (e.g., Sweden, USA, China). However, the operation of the autonomous machinery in these cases is either partial (semi-autonomous, teleoperated vehicles) and of small-scale or occurs at surface mines where GPS significantly facilitates the autonomous navigation of them.

Jan 1, 2019

By A. W. Randall

Geological Aspects of Ore Reserve Estimates of Pine Point District Zinc- Lead Deposits, N.W.T. Zinc-lead ores of the Pine Point District, Northwest Territories, Canada are hosted in paleokarst cavities within a Middle Devonian carbonate barrier complex. Of the nearly 100 deposits found, most are irregularly distributed along two main regional stratigraphically controlled trends. The ores, which occur predominantly as open space filling, form deposits most of which average one million tonnes in size with an average grade of 10% combined zinc plus lead. Geological features related to karsting control not only distribution of deposits but also their shape, size and grade. The higher grade ore in these deposits generally occurs in a relatively small core area. Consequently, accuracy of reserve estimation is dependent on drill hole density and understanding of karst geometry. Several case examples will be reviewed to demonstrate the relationship between shape, size and grade of deposit, geological reserves and drill hole density, along with a discussion of geological ore reserve estimation methods.

Jan 1, 1985

During a period of six months in FY2018, a series of trials were conducted to compare drilling accuracy using two different methodologies and the subsequent impact this had on ore dilution. Testing was conducted at Cracow underground gold mine in Queensland, Australia. The drill rig’s existing alignment process was compared to a new technology system with the following observations: - Using the existing alignment process only 20% of holes surveyed recorded toe points within the +/-300mm (11.8in) tolerance blast-hole deviation. - The new technology was proven to limit rig alignment error, reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%. The increased accuracy reduced stope dilution by reducing over-break of subgrade ore: - Stopes drilled using the new technology recorded 62.6% less average dilution. - This contributed to an overall reduction in dilution for the full year (FY18) of 5 percentage points compared to FY17 - from 22% to 17% (a net decrease of 22.7%). A cost-benefit analysis extrapolated from the trials stipulates that if the new technology were in use for a full 12 months, when applied to FY17 full year data, a 10 percentage point reduction in dilution would represent a net 45.4% decrease, and would result in AUD8.2M (USD5.9) additional ore recovered, with AUD4.5M (USD3.2M) less spent on wasted cost of haulage and processing of diluted ore. As a result, return per tonne would increase 22%, from AUD87 (USD63) to AUD106 (USD77.1). INTRODUCTION Dilution – planned and unplanned – remains a significant cost impairment in the mining process. A series of trials were held over a six-month period in FY18 which established the cost-benefit of new technology as it applies to the alignment accuracy of production drilling rigs in underground mining, thus confirming its ability to limit drilling as one of the causes of dilution. The trials identified three underlying factors affecting drilling accuracy, measurable by blast-hole deviation surveys of planned vs actual toe data. These were; rig alignment error, collar location change/error, and in-hole deviation. The trials involved a comparison of existing rig setup processes and technology, with the new technology (Minnovare’s Production Optimiser system). The trials were undertaken in the same environment; an operating underground gold mine - Cracow Gold Mine. The comparison first revealed the extent to which rig alignment impacts blast-hole deviation. Secondly, the new technology was proven to limit rig alignment error, thereby reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%.

Jan 1, 2019

By Daniel H. Knepper

Estimating the lithologic composition of gravel deposits for aggregate quality using standard field and laboratory techniques is costly and time-consuming. As an alternative, digital geologic maps and elevation models may provide a means for predicting the lithologic composition of channel and terrace deposits. Digital geologic maps can be used to evaluate the distribution of map units: their geomorphic setting, and the physical properties of the gravel source. To test this concept, the lithologies and topography of the upper drainage basin of the Big Thompson River along the Colorado Front Range were used to examine various factors that may control the final lithologic composition of channel and terrace gravels downstream. The simplest factor is the area of each of the map units in the upper drainage basin area, which can be easily measured from the digital geologic map. The percentage of each map unit within the total area provides a estimate of the pro- portions of each map unit that might be expected to occur in the downstream gravels. Published estimates of the hardness and durability of each map unit were used to calculate physical property-weighted areas; these areas are an estimate of the potential of each unit to be eroded and transported as gravel-sized particles. The areas of each map unit at 1-kilometer intervals from the drainage basin exit point were used to calculate a distance-weighted area for each map unit. For this study, a simple inverse relationship (area/distance) was used for distance weighting, but a more complicated distance function may ultimately be required. The topographic setting of exposed rock units should exert a significant influence on whether material will move slowly or rapidly through the drainage system. Two topographic factors were examined: gradient and slope. A simple gradient between map unit occurrences and the exit point of the drainage basin was used to calculate a gradient-weighted area estimate for each map unit. The slope-weighted area estimate uses the slope steepness (in degrees) in the immediate vicinity of each map unit occurrence as a measure of the tendency of material to begin moving into the sediment transport system. The primary intent of this study was to test the concept of using digital geologic map and elevation images to estimate gravel composition, rather than actually producing a useful analysis of a drainage basin. Each of the controlling factors was examined independently to gain an understanding of the magnitude of the effect of each factor. Ultimately, a comprehensive predictive model will be constructed using a combination of the various controlling factors.

Jan 1, 2001

By L. Gutierrez, J. S. Castro S. Laskowski

Water is a medium in which flotation takes place, and flotation efficiency is highly dependent on water quality. Of the total water resources on Earth, less than 2.5 percent is fresh water. This water is used in agriculture, by households and by industry. Among the industrial users of fresh water, the mining industry occupies an important position. Furthermore, mining operations are often located in arid areas with very limited access to fresh water. The demand for and shortage of water in these parts of the world, such as the Atacama Desert in Chile, makes the use of seawater by the mining industry the only sustainable solution. 

Compagnie Minière Espérance mines a primary gold orebody in an openpit. The ore is processed through crushing, primary gravity concentration, grinding and secondary gravity separation, generating tailings with remaining fine gold. Analysis of the material in the pond has indicated a residual gold grade sufficient to justify a chemical treatment process to recover the gold. However, direct cyanidation would require a prohibitively large installation for the site, which is located in a remote rainforest environment. It was decided to test the feasibility of preconcentration using flotation. As lab tests proved up the technical feasibility of the flotation process, an on-site pilot operation was carried out to assess the continuous circuit performances, define the best configuration and obtain enough data for industrial circuit sizing. Data collected during the pilot campaign was used for calibrating a process simulator built with the USIM? PAC software. The simulator validated the feasibility of upgrading the existing plant, including the reprocessing of tailings to obtain an acceptable fine gold recovery from a small amount of concentrate.

Jan 1, 2010

By Robert M. Dreyer

Although lateritic deposits have long been a principal source of bauxite and are becoming an increasingly important source of nickel, the problems in the evaluation of such deposits are not generally understood. In the evaluation of lateritic bauxite and nickel deposits, there are many similarities, but there also. are significant differences. It has long been recognized that laterites with commercial concentrations of trivalent metals represent the ultimate in the intense leaching of tropical soils. Any factors which effect-the rate of soil leaching will effect the form of local lateritic concentrations. Although the most intense leaching generally occurs on somewhat elevated areas of gentle relief where there is a free downward flow of rain water, the- effect of local rock structures in effecting varia¬tions in soil metal concentrations has-not been well understood - primarily because the laterite forms a masking blanket over the rocks from which the laterites were derived. All of the-factors which facilitate downward movement of water may effect greater surficial concentrations of trivalent metals. Such features as zones of fracturing, zones of greater rock permeability, and areas of karst topography may, therefore, be responsible for greater leaching. The variations in rock structures and the vagaries of ground water flow pat¬terns impart, to the laterites, rapid lateral and vertical variations in thickness and metal concentrations. Because of such rapid

Jan 1, 1970

By J. Kou

In this paper the activation behavior of quartz using Ca(OH)2 as an activator in quartz reverse flotation with anionic collector was evaluated and their adsorption behavior was investigated using a variety of techniques. The adsorption of the collector KS-I on the surface of quartz with and without Ca2+ was primarily characterized using Quartz Crystal Microbalance with Dissipation technique (QCM-D), which is a high sensitivity in-situ surface characterization technique. The flotation performance was evaluated using a laboratory mechanical flotation cell at different process parameters such as pH, collector dosage, and Ca(OH)2 dosage. The anionic collector evaluated was a commercial fatty acid KS-I. The QCM-D data showed that the collector adsorbed on quartz more readily with Ca2+ as activator. The mass and structural property of the collector layer adsorbed on quartz surface at 2.16×10-3 mol/L of Ca2+, 0.3 g/L of collector and pH 12.0 have been studied using the technique of QCM-D. The chemisorption of the collector KS-I on the surface of quartz in presence of Ca2+ were also demonstrated by means of zeta potential, QCM-D and FTIR analysis.

Feb 23, 2014

By M. K. Mohanty, H. Akbari, L. A. Ackah

Dry separation was the predominant method of coal cleaning in the United States from the 1930s to 1980s. The application peak of dry separators for cleaning raw coal was in 1965, when about 23.1 Mt of cleaned bituminous coal was produced. The main advantage of dry coal cleaning is the elimination RIWKH GHZDWHULQJ VWDJHV DQG VLJQL¿FDQWO\ UHGXFHG moisture in comparison to wet processing. In addition, developed dust control systems have made dry cleaning method an environmentally friendly process. The largest air-based coal cleaning plant was built in Pennsylvania in 1968 and could clean 1,272 t/h of raw coal sized smaller than 19 mm. This was followed by a decline in dry coal cleaning to less than 3.6 Mt in 1988. Some of the main reasons that shifted coal operations IURPGU\WRZHWSURFHVVLQJZHUHWKHQHHGIRUPRUHHI¿FLHQW separations with lower density cuts, increase in raw coal surIDFHPRLVWXUHVSHFL¿FDOO\LQXQGHUJURXQGPLQLQJWRFRQWURO GXVW ¿QHUSDUWLFOHVL]HUHTXLUHPHQWV LQFUHDVHLQ¿QHVLQUDZ coal from underground mines, and health and safety concerns related to dust and noise (Arnold, Hervol and Leonard III, 1991; Miller, 2011).

By Atta Ur Rehman, Kwame Awuah-Offei

This work evaluates the effectiveness of similitude theory in predicting the draft of a rubber tire loader’s bucket during initial penetration. The work uses 1:16 and 1:8 scale models of an 18-t capacity load haul dump, scaled with the Buckingham Pi theorem, to evaluate the prediction of draft and penetration under different operating and different dynamic conditions. We hypothesized that the observed relationships between draft and longitudinal penetration and the operating and dynamic conditions will hold true for an upscaled model. Similarly, we hypothesized that the results of experiments conducted with the smaller scale model should predict the draft on an upscaled model.

By Albert J. Kritscher

The Similkameen Copper Project located near Princeton, British Columbia, is operated by the Similkameen Mining Company Limited, a wholly-owned subsidiary of Newmont Mining Company. The orebodies for this project are located on both sides of the Similkameen River for which the project is named. The project involves the processing of an average of 15,000 STPD of andesitic ore, mineralized largely with Chalcopyrite, at an overall plant availability rating of 90 percent. Project life is nominally 15 years. Design for the plant and its ancillary facilities was undertaken by Bechtel Corporation with procurement and construction management by Canadian Bechtel Limited. Construction began in June 1970 and first ore was introduced into process in March 1972. This paper concerns itself only with the project tailing system. The processing plant is located on a bench of glacial stream gravels which overlooks the river canyon. This site represented the only relatively flat area of sufficient size to accomodate processing facilities near to the ore- bodies. Reference is made to Figs. 1 and 2 showing the relationship of project features in plan and profile.

Jan 1, 1973

By G. Fehr, B. B. Panda, R. Bansberg, K. Arnold, T. Freiman

To evaluate the potential for process solutions to contaminate groundwater outside of the area of the Oxide Pit, it is necessary to predict the ultimate maximum pit lake elevation once pit-related mining activities have ceased. A water balance model was developed based on the existing pit geometry, the groundwater flow equation, and assumed hydrologic input parameters. The model assumed that at any point in time, total inflow into the system (i.e., direct precipitation, surface water and groundwater) minus outflow from the system (evaporation from the lake surface) was equal to the change in the pit water volume. The pit lake depth over time was predicted by assuming a succession of steady- state water balance conditions over short time increments. An analytical method using a spreadsheet and computer model was employed in this study to model the filling of the lake in the Oxide Pit. A sensitivity analysis was performed to evaluate uncertainty associated with the input parameters in the model. The sensitivity analysis indicated that the model was most sensitive to values of precipitation and evaporation and to the static water table.

Jan 1, 2003

By E. Watkins, S. J. SCHATZEL, K M. AJAYI, V. Gangrade, Z. Khademian

A stochastic discrete fracture network (DFN) model is developed based on mine site core log data to predict the horizontal and vertical permeabilities from the surface to the top of the caved zone at a longwall mining site in southwestern Pennsylvania. One hundred DFN realizations were generated to determine permeabilities for the isolated zone over an abutment pillar after mining the second panel. The results from this study show that the vertical and horizontal permeabilities from the DFN model agree closely with field measurements, which indicates that the resultant permeability obtained from the field measurements is representative of the predicted permeabilities. With this agreement, the aperture data for other zones of the mine could be obtained from the geomechanical model — specifically, for the fractured zone over the gob. Based on the successful validation of this model, this model could be further developed to predict the permeability of the fractured zone over the gob with fracture aperture obtained from the geomechanical analysis. This will complete the fracture characterization of the overburden, which could be used to predict potential shale gas flow to the mine in the event of a breach. This prediction could provide information on the associated risk of a casing breach and determination of methods to proactively prevent such an occurrence.

Feb 1, 2023

By J. A. Marts

Reservoir properties including porosity and permeability distributions in longwall coal mine gobs have direct application to modeling the flow patterns and gas distributions in the gobs. Proper assessment of these distributions is required to assess gob gas hazards such as spontaneous combustion and explosive methane mixtures and to optimize gob gas venthole operation and nitrogen inertization. Determining the reservoir properties is difficult given that the gob is inaccessible and direct measurements cannot be easily taken. Several techniques have been used by previous researchers and will be discussed. This paper will present the methodology used to model the gob compaction by simulating the sequential extraction of coal. Two Western US coal mines were used for case studies. By determining volumetric strain, the porosity and permeability distributions in the gob can be calculated. The geo-mechanical model predicts an axisymmetric volumetric strain distribution with a steeper slope near the start-up room and a shallower slope near the active face.

Feb 23, 2014

By Peter N. Calder

There is little doubt that the stability of both highwalls and spoil piles is essential to efficient strip mining. Accurate determination of the appropriate geotechnical parameters will pay dividends during mining, but only if the mine operation closely follows the engineering plans which have incorporated These factors. Productivity is invariably higher in mines where failure of highwalls and spoil piles does not occur. This is the result of the reduced rehandle and better working conditions found in stable mines. Control of the waste piles and highwalls also leads to better coal recover since failures can result in the burial of uncovered coal, which is then lost to mining. Safety is an important consideration. The importance of providing a safe working place for employees and of protecting costly mining equipment is hard to overemphasize. For miners, working in areas where instability exists, the degree of hazard involved in their occupation is increased particularly where night operations are involved. It is true, too, that there have been many cases where loading equipment has been buried and severely damaged by failures.

Jan 1, 1980

By Dominic F. Howarth

Cuttability and borability assessment methods in rock and coal are reviewed. TBM, roadheader and coal cutting machine boring rates can be predicted from a knowledge of machine, intact rock property and rock mass parameters. Results that were obtained from a detailed analysis of two TBM borability prediction methods and comparison with data from twenty case histories, show that a simple, low-cost method that uses one machine parameter and one rock parameter compares very favourably with a sophisticated, high-cost method that also includes details of rock mass characteristics (discontinuity, type frequency and orientation).

Jan 1, 1987

By D. W. Hutchinson

One of the most important problems facing the coal industry today is the disposal of refuse from the coal preparation plants in a safe, economical, and efficient manner while complying with all legal requirements. The most commonly used refuse disposal method has been landfill/impoundment. In this method, the coarser refuse fractions are disposed of by layering and compaction into a landfill. The fine coal slurry refuse fraction is impounded in a dam constructed of a portion or all of the coarser refuse fractions. The failure of an impoundment at Buffalo Creek, Saunders, West Virginia and the sliding failure of a coarse refuse pile at Aberfan, Wales, England, resulted in an evaluation of refuse disposal methods by various regulatory agencies as well as coal producers. The result of this evaluation was the promulgation of Federal regulations dealing with the preparation, operation, and final abandonment of coal refuse disposal areas. As a consequence of these regulations the use of the landfill/impoundment method of disposal became in some cases economically unfeasible or technically impossible. At the time of the promulgation of the new Federal regulations, United States Steel Corporation was in the process of designing the Cumberland preparation plant. As a result of the new regulations

Jan 1, 1977

By M. E. Gershon

Software for coal blending has gained a lot of recent attention as micro-computer programs have come on the market. Some of this software is appropriate and some is not. This paper looks at the types of models being used and points out the strengths and weaknesses of each. Recommendations are then made concerning the level of detail required for these programs, relating this concern to the various ways in which coal companies are using these programs. A checklist of company requirements for these programs and available pro-gram-features provides an aid in matching the program to the company.

Jan 1, 1988