Search Documents

By E. L. Smith

The development of larger size flotation machines, which started in the 1950's and 19601s, is still proceeding. The largest mechanical flotation machines available today have unit volumes in the range of 38 to 42 m3 (1,350 to 1,500 cft). In fact, the motivating forces of increasing capital and energy costs and decreasing ore grades, which created the need for large flotation cells, not only still exist, but are becoming more critical. This paper reports the development of an improved mechanism for these large flotation machines. The starting point in the development of a new mechanism was the identification of design and performance features of existing machines where improvements were desirable. The result of this work was a mechanism which is an improvement over existing designs. This new design is characterized by an efficient overhung stator and a vortex profile rotor. The overhung design of the stator removes unnecessary and undesirable baffling in the lowest parts of the tank, while maintaining a quiescent froth layer. This results in lower power consumption and better pulp circulation and solids suspension. The vortex profile rotor acts as an efficient pump, with higher pulp recirculation rates as evidenced by the increased air dispersion capabilities, good solids suspension, and low power consumption.

Jan 1, 1982

By Bernard Y. Saltie

The White Pine orebody is characterized by a high lateral stress or highly faulted and joined conditions. Because of these difficult conditions roof support has always been a main concern. Mechanical bolts were widely used in the early seventies; however, it became apparent that major improvements in ground control were required if safe operation at White Pine was to be continued. The first step was taken in 1973-1974 with the testing of resin bolting. Record of caves and roof-falls with either type of support demonstrated superiority of resin bolting versus mechanical bolting - Safety was dramatically improved which was the absolute first consideration; however resin bolting was still more expensive than mechanical bolting. In order to generalize resin bolt installation, the second step was therefore to acquire special roof bolters compatible with resin bolting. The machine was to enhance the safety of the operation. This was achieved by the acquisition of the Secoma bolting machine equipped with an automatic bolting turret. Being a "hands off" operation the safety of the operator is total. Using a fixed taped attachment of the drill steel on the chuck a front guide and an automatic regulator torque thrust on the steel drilling in small diameter was possible. Being a fully automatic process only one operator is required per machine versus two operators with the conventional machines. The two main objectives were reached enabling the extension of resin bolting to the whole mine.

Jan 1, 1980

By Henry N. Doyle

One can hardly discuss coal pneumoconiosis unless it is placed in the context of the total pneumoconiosis problem in the mining industry. However, it might be well if first we defined a few terms, since it has been my experience that the use of the word pneumoconiosis frequently causes con- fusion among those who are not familiar with the term. Pneumoconiosis comes from two Greek words meaning lung and dust. Hence, the word pneumoconiosis simply means dusty lung, or dust on the lung. There are many forms of the disease, some of which are disabling and some are not. Among the many dusts which cause pneumoconiosis might be included silica, asbestos, coal, talc, iron ore, and many other mineral dusts. Silicosis is a specific form of pneumoconiosis. It is caused by the inhalation of excessive amounts of silicon dioxide in the form of crystalline quartz. The disease is manifested by nodulation of the lungs which is apparent on an X-ray film. Continued exposure to silicon dioxide causes the nodules to grow and ultimately large areas of the lung become scar tissue which pre- vents the lung from performing its physiologic function. In its more advanced stages, there is a significant loss of pulmonary function which accounts for

Jan 1, 1966

By D. E. Munson, T. M. Torres, D. A. Blankenship

The Thermal/Structural Interactions (TSI) In Situ Tests are a series of large scale, well instrumented tests that have been constructed at the Waste Isolation Pilot Plant (WIPP) in southeastern New Mexico. As a precursor to the TSI tests, a ventilation drift (Room D) was mined, drilled and instrumented. This room provided the contractor an excellent area to practice controlled construction methods and was a proving ground for construction monitoring and documentation methods. All gages in this first room have been monitored since their initial installation, which has provided a small, but representative, data base. These data also were the first to be available from any TSI area for analysis. This paper discusses the construction activities in Room D and the data generated from the construction and drilling. Deformation of the room is compared briefly to numerical calculations that used a rather simple creep model as a reference. The constitutive model for salt, it appears, must be improved before it can predict the underground deformations.

Jan 1, 1986

By R. B. Elver

The level of steel consumption per capita is one of the principal indicators of a country's standard of living. It is no coincidence that the materially advanced nations possess viable iron and steel industries to provide a reliable and economic source of steal for the manufacturing industries. No other metal is as dominantly important in manufacturing as steel. The blast furnace - steel furnace complex based on coking coal, ferrous scrap and iron ore - continues to be the principal steel-producing method. Less important is the electric furnace method based on scrap, In recent years, there has been considerable interest in the many direct reduction processes that are not dependent on coking coal but usually produce a product for further refining in steel furnaces. No matter which series of processes are used, iron ore is essentially the only source of virgin iron units. Thus, to such a vital and capital-intense industry as steel, access to a relatively inexpensive, long- term supply of iron ore is essential.

Jan 1, 1964

By M. B. Haggerty, R. J. Sheets, F. Abbasy

To address coal refuse tailings storage needs for a mine operation in western Canada, a feasible solution was to convert excavated open pits into tailings cells. A slope stability investigation and design study were completed to determine the necessary width and slope geometry for in-situ native plugs as the impoundment embankment. The native plugs separate the previous open pit from the current active open pit. This configuration allows for the deposition of refuse tailings in the previous pit while allowing mining to safely continue “downstream” of the temporary impoundment. As mining progresses, each subsequent pit will be filled with refuse tailings; thereby, buttressing the upstream slope of the previous native plug. Although these cells are excavated, and the timeframe for downstream exposure is relatively limited, the native plugs are classified as dams and must be designed to meet applicable safety of dam standards since they impound water and tails above mining personnel in the subsequent open pit. The presentation and paper will discuss the investigation and analysis conducted to develop the geotechnical and hydrogeological design recommendations.

Mar 2, 2022

By Gerald W. Cormick

In a complex society such as ours, the range of "negotiating" relationships is constantly increasing. These negotiating relationships have emerged as a direct result of the diffusion of power or influence to new sectors and emerging concerns. Even within organizations, the myth of the authority-based heirarchical structure has given way to the reality of constant negotiations between superior and subordinate and with peers in the organizational structure. In the broader context, the corporate organization finds it necessary to reckon and often negotiate with organized employees, suppliers, buyers, government agencies and a range of organized private interests ranging from minority groups to environmental organizations. In response to this diffusion of power and the conflicts which it has engendered, a variety of conflict avoidance, conflict managing or conflict resolution techniques has developed. The purpose of this paper is to attempt to differentiate between some of the conflict intervention approaches which have appeared "on the market", and to suggest three bases for selecting among them: 1. The "role" of the conflict intervenor; 2. How far the conflict has developed; and 3. The breadth and impact of the issues involved.

Jan 1, 1979

By R. K. Clifford

The formation of elemental sulfur on the surface of sphalerite in aqueous systems was investigated. Hallimond tube flotation tests showed that unoxidized sphalerite did not float well without a collector. Flotation recoveries of greater than 95 percent were obtained without the use of a collector or frother after the sphalerite had been reacted with oxygen under pressure and water at pH 2.8 at room temperature. High flotation recoveries also resulted when sphalerite was reacted in acidic solutions in the presence of platinum sponge, titanium sponge, 316 stainless steel, copper turnings, or [10-5M++]. Conditions which produced high flotation recoveries of sphalerite yielded contact angles of 37° to 40° and also produced elemental sulfur. The increase in elemental sulfur on the surface of sphalerite was detected by elemental sulfur extraction with petroleum ether, electron spectroscopy for chemical analysis (ESCA), and the electron beam microprobe. The quantity of elemental sulfur formed was insufficient to be detected by infrared or Raman spectroscopy, or by the optical microscope or by the scanning electron microscope. An electrochemical type reaction for the production of elemental sulfur in acidic solutions was proposed. The cathodic reduction of oxygen was the slow step which needed to be catalyzed. A chemical type reaction which produced H2S rather than elemental sulfur was evident in non-oxidizing conditions.

Jan 1, 1974

By H. K. Lin

The free-milling ore characteristics of the Fort Knox gold deposit are ideal for studying gold and silver behaviors in various processing circuits without serious interference of sulfide minerals and other refractory factors. A galvanic effect leads to faster silver dissolution than gold dissolution and, as a result, the Au/Ag solution concentration ratio increases through the leach circuit. In the CIP circuit, Au adsorption is more effective than Ag adsorption. The Au/Ag solution concentration ratio decreases from 10.0 to 1.0 as the slurry advances from CIP tank #1 to CIP tank #5, while Au/Ag ratio in the carbon increases from 3.2 to 15.3, as the carbon advances from CIP tank #5 to CIP tank #1. Silver is stripped more effectively than gold from the loaded carbon. The Au/Ag ratio in solution reaches 2.0 in the first 75,700 L of strip solution that pass through the loaded carbon; as the stripping process continues, the Au/Ag ratio in the strip solution increases. In the electrowinning circuit, the Au/Ag ratio in the spent electrowinning solution is significantly lower than that in the electrowinning feed, indicating that Au is more rapidly deposited onto the cathode than Ag.

Jan 1, 2010

By Odin Wilhelmy

Agriculture in the United States today is becoming more and more a business, rather than a way of life. In the light of this, it behooves the farm-supply industries that provide the American farmer with his tools of production--feed, fertilizer, machinery, and the like--to give even greater attention than they have in the past to meeting the needs of the farmer-businessmen they are serving. Increasing competition among the companies that make up these industries merely accentuates this need for better service. An opportunity for such improved service, not yet fully realized, exists in the fertilizer industry today. That opportunity lies in the increased transportation of fertilizer ingredients by water. However, before the benefits inherent in this increased water movement of fertilizers can be fully realized, certain obstacles must be met and overcome. It is the purpose of this paper to outline the nature and magnitude of this opportunity, to point out some of the roadblocks and the steps that can be, or are being, taken to remove them, and to indicate some of the rewards that would logically stem from success in these efforts.

Jan 1, 1961

By Trevor R. Ellis

In this paper a method is presented for estimating the specifications of sandstone-type uranium deposits which will be the minimum that can meet a company's economic requirements for investment. The method interpolates and extrapolates from available cost data for typical mines to provide the costs for a wide range of possible deposits. The range of deposits achieving the company's required discounted cash flow rate of return on investment at an estimated uranium oxide selling price is then calculated, thus giving the complete range of deposits which meet the minimum required specifications. Prospects are then evaluated by comparison with these minimum requirements.

Jan 1, 1979

By G. H. Gronhovd

The U.S. Geological Survey estimate of the total remaining reserves of lignite in this country as of Jan. 1, 1967 was about 448 billion tons. This represents 27 percent of the total coal reserves on a tonnage basis and about 17 percent on a thermal basis. Approximately 98 percent of these reserves are in a vast lignite field located in western North Dakota and eastern Montana. This field also extends north into the Canadian province of Saskatchewan. Despite these large reserves and relative ease of mining by stripping operations, lignite production historically has accounted for less than 1 percent of the national total. This is largely due to the fact that the lignite deposits are located in an area that has no large centers of population and the economical radius of transportation is limited by its relatively high moisture and low heating value. Commercial utilization of North Dakota lignite for power production became firmly established in the mid-1920's with the development of the first successful lignite-burning equipment. Most of the early lignite-fired boilers were equipped with spreader stokers, but as the size of the plants increased, pulverized-coal firing became the more popular method, and with few exceptions, the plants built during the past 15 years are pc-fired.

Jan 1, 1968

By Ray Brainard, Adriana Ventimiglia, Amanda Kerr

The $2 billion Horizon Lateral includes over 30 miles of trenched and tunneled pipeline with diameters up to 120 inches.Related infrastructure includes large and small pumping stations, reservoirs, and flow control facilities. This paper will discuss the strategy and processes used to determine contract packaging and contracting delivery methods for the various project elements with an emphasis on the tunnels and trenchless crossings. Prior Authority experience and the rigorous risk-based approach to develop the preferred alignments played a large role in determining the outcomes along with schedule concerns and permitting and easement acquisition.

Jun 13, 2023

By L. Barnewold, A. Merchiers, M. Pütz, P. Jeschke, M. Dammers

The mining industry faces many difficult challenges, for example, lower ore grades, smaller and deeper deposits, and longer transportation distances. In the past, there have been remarkable innovations in both equipment and the types of mining methods for which it is used, which have resulted in economies of scale. This has led to an increased use of bulk mining methods, like sublevel and block caving, which has increased productivity and reduced costs. Haulage alone plays a major role. Current haulage techniques are a significant cost driver, which account for between 15 and 30% of the overall capital investment (capex) in a mine and are an increasingly part of the operating costs (opex). The paper introduces a simulation tool of main haulage system in underground mining. Therefore, performances and the costs of the three most common underground main haulage systems, rail, truck, and conveyor, are calculated using a developed modeling tool. The tool was applied and validated in a case study carried out with the LKAB Kiruna Mine in northern Sweden.

By J. Navoyski, B. Macdonald, W. J. Helfrich, J. L. Bellanca, B. Demich

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of company names or products does not constitute endorsement by NIOSH. ABSTRACT Recent advances in computing, rendering, and display technologies have generated increased accessibility for virtual reality (VR). VR allows the creation of dynamic, high-fidelity environments to simulate dangerous situations, test conditions, and visualize concepts. Consequently, numerous products have been developed, but many of these are limited in scope. Therefore, National Institute for Occupational Safety and Health researchers developed a VR framework, called VR Mine, to rapidly create an underground mine for human data collection, simulation, visualization, and training. This paper describes the features of VR Mine using self-escape and proximity detection as case studies. Features include mine generation, simulated networks, proximity detection systems, and the integration and visualization of real-time ventilation models. INTRODUCTION There are many definitions of virtual reality (VR) that include various levels of immersion and features [1]. Some definitions refer to specific technologies [2], while others are limited to visualization [3]. For this paper, a more general definition of VR will be adopted. VR is defined as the collection of hardware and software that interactively engages users and stimulates their senses within a synthetic or virtual environment. From a hardware standpoint, this can include anything from a phone to a head-mounted display (HMD) to a large-scale theater as well as speakers, microphones, haptic sensors, and interaction devices. The software used to create virtual environments (VEs) generally includes a game engine, custom software components and libraries, and two-dimensional and three-dimensional graphical assets. Recent hardware and software advances have increased the fidelity and availability of VR. New and improved technologies including HMDs and high-resolution monitors and projectors can display sharper, more detailed visualizations. For example, in the past five years between the release of the Oculus Rift DK1 (2013) and the HTC Vive Pro (2018), there was a three-fold increase in resolution along with a 50% increase in the refresh rate. Furthermore, despite early claims that low-cost VR technology was readily available [4], computational power has not been sufficient to handle the large amount of data generated by these systems [5]. In the past five years, however, rendering speeds have more than doubled and memory has more than tripled [6], allowing these visualizations to be incorporated into higher-complexity and -fidelity VEs that more closely mirror the real world. Similarly, software capabilities have also significantly improved through game engine advancements and feature development. In the past several years, game engines have added and improved features such as physics, lighting, platform support (e.g. Android), and asset development integration. Some of the current leading commercial game engines are Amazon Lumberyard, CryEngine, Unreal, and Unity, but this can quickly change as is evident in the literature [7, 8].

Jan 1, 2019

By J. G. Groppo

Eastern U.S. oil shale contains approximately 10 to 12 gallons of oil per ton and 7 to 10 percent pyritic sulfur. Physical beneficiation of these low grade shales using froth flotation provides a high grade material which will make extraction of oil more economically attractive. The Alabama oil shale used in the present study contained 16.46 percent organic carbon and 14.5 gallons of oil per ton as determined by Fischer assay. Liberation size of the kerogen was estimated at 10 /-Lm. 'Ken-Flote' column flotation technology provided a high grade concentrate containing as much as 60 percent organic carbon, however, carbon recovery was about 60 percent. Carbon recovery was improved to 75-85 percent while maintaining concentrate grades in excess of 40 percent carbon by providing longer retention time in the column which facilitated effective bubble-particle collision and attachment.

Jan 1, 1993

By Joseph M. Zigich

The Anaconda Minerals Company operates a molybdenite and copper producing mine and mill facility near Tonopah, Nevada. Included with the milling facility is a ferric chloride leach plant for removal of copper mineralization from the molybdenite concentrates. Discussed are the engineering and construction schedules associated with the leach plant. The chemistry associated with the process along with a description of the process flow, equipment, and operating parameters are contained in the paper.

Jan 1, 1983

By Hugh Douglas

This paper discusses the financial health of the U.S. mining industry and its ability to meet the future raw material requirements of this country in the context of resource independence. The title of this paper begs several questions, and three will be raised here. The answers to them will form the basis for discussion. The three questions are: What does one mean by resource independence. How is the U.S. mining industry defined. How is financial health measured.

Jan 1, 1977

By Clark Harrison

It is not uncommon for overall quality of coal from a mine to deteriorate as the mine is developed or for an improved-quality coal specification to be imposed during the life of the mine. Either of these conditions typically results in management pressuring mine personnel to take greater care in delineating the seam from top and bottom rock. When mining and seam conditions require a portion of the seam to be removed to ensure sufficient rock is removed to meet the quality specification, physical-coal cleaning may become economically competitive with in-pit seam grooming. The additional cost of coal cleaning may, in some cases, be justified by permitting higher recovery of the coal seam than is possible when cleaning the seam with excavators in the pit. This paper compares projected coal cleaning results with present in-pit grooming techniques and reports the economic results.

Jan 1, 1987

By D. M. Hausen

Carbonaceous gold ores are ubiquitous to virtually all of the Carlin-type gold deposits along the Carlin gold belt in north central Nevada, representing the unoxidized "zones" of presumably extinct thermal spring systems of mostly Tertiary age. A period of subtropical weathering resulted in deep sub-lateritic zones in most deposits to several hundred feet below surface. Carbonaceous ores below this supergene profile of weathering have been investigated by various methods, including petrographic study, standard geochemical and organic carbon analyses, carbon and hydrogen isotopic ratios, electron-spin resonance spectra, infrared spectra, and DTA techniques. Results have been integrated with recent findings by other investigators utilizing fluid inclusion and thermal brine data to indicate a first phase hydrothermal solution temperatures and pressures at a minimum depth of 6 km under normal geothermal gradient. This phase resulted in the quartz-barite-calcite vein filling of the host rocks. Gold mineralization took place later at shallower depths. Primary organic material in carbonaceous ores from the Carlin and other mines appears to be a pyrobitumen residue derived from an old oil pool that had been heated by the thermal solutions, and from which the light hydrocarbon fractions were removed. Some of the bitumen was remobilized along silicified veinlets in the ore, but its role in the emplacement of the gold, itself, is not clear. The gold was localized submicroscopically in fine pyrite, mostly in framboids, and as fine metallic particles, but does not appear to be concentrated within the carbonaceous matter per se. However, reducing conditions associated with bituminous residues are believed to have been favorable for gold deposition.

Jan 1, 2013