Search Documents

By Richard B. Stein

This paper will present an overview of several hydrometallurgical processes which can be used for sea-nodule metal recovery and some simplified economics. Before going any further, here are some of the basic figures from which the economics were developed. The first is to establish a representative composition for a typical nodule feed (Slide 1). This set of chemical analysis figures can be taken as typical for a deep Pacific nodule feed and shows manganese at 30%, copper at 1.1%, cobalt at 0.2%, nickel at 13% and iron at 10% for the metals of economic interest1.

Jan 1, 1982

By E. A. Metz

Silicon dioxide, silica, is the most common oxide in the earth' s crust. The health effects of silicon dioxide dust have been known since Biblical times. Agricola's book, published in the mid 1500's on occupational medicine, described a lung disease that afflicted miners. He observed a disease in miners that caused shortness of breath, coughing and wasting. Add fever, chest pains and fatigue and we have the current symptom complex of silicosis. As we approached the 21stcentury, the Labor Department began an aggressive campaign to combat silicosis-a preventable disease. Unfortunately, many publications do not clearly differentiate the polymorphs of silica known to mineralogists. Crystalline silica, i.e., alpha quartz, tridymite and cristobalite need to be considered differently from the amorphous forms of silica. Freshly fractured surfaces of the silica and host specific responses will be examined. Recent research focuses on the biologic interactions of free radicals generated by mineral particles. This results in cell injury and DNA damage, in turn leading to fibrogenesis and possibly carcinogenesis. In addition to particle-cell interactions, emphasis is given to lung defense mechanisms.

Jan 1, 1998

By M. Scaggs, K. Phillips

"Coal Worker’s Pneumoconiosis (CWP) is an occupational lung disease caused by chronic exposure to respirable mine dust. After decades of steady decline, CWP incidence appears to be on the rise since the mid-1990s, particularly in some regions of Appalachia. Alarmingly, many of these cases have rapidly progressed to the most advanced form of CWP, referred to as Progressive Massive Fibrosis (PMF). Most of what is currently understood about respirable mine dust has been gleaned from routine regulatory monitoring, which tracks total mass concentration of respirable dust (mg/m3) and, less frequently, silica mass content. This paper focuses on the use of thermogravimetric analysis (TGA) as a way to provide basic characterization of the whole composition of the dust, allowing it to be classified into three mass fractions – coal, carbonate, and non-carbonate minerals. TGA was conducted on 59 dust samples collected by miners from eight coal mines in central Appalachia, and the results are discussed in terms of differences between mines, regions, and primary occupations. Consistent with prior results on area dust samples from some of the same mines, results of the personal samples generally show that the coal mass fraction of the dust is relatively low. Carbonate and non-carbonate minerals thus tend to make up the bulk of the dust mass, and vary across occupations and specific mines. INTRODUCTION After nearly four decades of decline, the prevalence of Coal Workers’ Pneumoconiosis (CWP, or “black lung”) in the US has been on the rise since the mid-1990s (Laney et al., 2014; Laney et al., 2010; Suarthana et al., 2011; Pollock et al., 2010; Antao et al., 2005; Blackley et al., 2016). Particularly alarming is the number of cases of progressive massive fibrosis (PMF), which is the most advanced form of the disease (Pollock et al., 2010; Antao et al., 2005; Blackley et al., 2016; Laney et al., 2017). A recent study by Laney et al. (2017) observed 192 US coal miners participating in the Coal Workers’ Health Surveillance Program (CWHSP) who had been diagnosed with PMF since 2000. Of the 163 (85%) that had a normal radiograph on file to use as a baseline, 27 (17%) of these individuals had progressed from a normal radiograph to PMF diagnosis in less than 10 years. Moreover, 162 (84%) of the individuals in that study worked in KY, WV or VA, and 169 (88%) had only ever mined underground. Blackley et al. (2016) also reported on a group of 60 PMF cases that were discovered by a single black lung clinic in eastern KY. Since seeking care at such clinics and participation in the CWHSP are voluntary, and could be influenced by a number of factors, these recent reports may well overestimate the degree of resurgence in severe disease (i.e., versus disease that was previously under-reported). Even so, they highlight a critical need to better understand the cause(s) of disease development and progression – such that effective interventions can be devised."

Jan 1, 2018

By M. B. Haggerty, Joe Welna

The Minnesota Department of Transportation is constructing a stormwater storage facility (SSF) along Interstate 35W (I35W) south of downtown Minneapolis, MN. The project will provide storm surge capacity reducing the frequency with which major precipitation events result in flooding of I35W. The design consists of six, 42-foot diameter, 90-foot deep, adjacent underground shafts providing 14.7-acre feet of storage. Construction challenges include high groundwater with variable glacial outwash deposits. Constructability and ground variability were managed using construction manager general contractor (CMGC) project delivery. CMGC provides an environment for collaboration and innovation starting in the design phase and carrying through construction. This paper provides an overview of key efficiencies and collaboration examples implemented on the I35WSSF project which were aided by CMGC delivery.

Jun 13, 2023

Dravo Corporation was founded in 1891 and has long been recognized as a major domestic engineering and construction firm headquartered in Pittsburgh. In 1977, Dravo had revenue of $852.2 million with international business activities contributing $248 million; quite a different picture than envisioned at the turn of the century. Engineering and construction activities still dominate Dravo's most recent history and will do so for the immediate future. However, fluctuations in capital spending by large industrial sectors of our economy during the late sixties were affecting Dravo's planning for continued growth along its traditional lines of business. Diversification was a possible solution to smooth out the upward trend in corporate earnings. One large result of these continuing efforts was the formation of Dravo Lime Company, a vertically integrated, proprietary chemical supplier for the air pollution control market. Briefly retracing the seventies, the passage of the Federal "Clean Air Act" in 1970 supplied the impetus for Dravo Lime Company. This law promulgated limits on the emissions of sulfur dioxide (SO2) from large stationary sources that would affect local air quality. The major industry that felt the brunt of this regulation was the electric utility industry, especially those generating electricity with coal-fired boilers. The law hastened the development of a new industry, flue gas desulfurization (FGD), and is composed of three major segments: (1) the electric utility, (2) the FGD equipment suppliers (the scrubbing modules), and (3) the scrubbing chemical suppliers. Dravo's experience suggested the equipment end of the business but market analysis indicated that our long range corporate goals could be better attained by investigating the chemical processes involved in the removal of the SO, gas. The result being Dravo Lime Company. This paper will briefly describe the Thiosorbic lime scrubbing process and review our innovative mine and calcining facility.

Jan 1, 1978

By B. Yarar

Samples of coal from an adit in the Fording River District of British Columbia showed hydrophilic properties between depths of 0-24.5 meters and was naturally hydrphobic at higher depths. Laboratory experiments indicated that weathered samples (i.e., those mined at 0-24.5m) could be upgraded by froth flotation at pH<2 following slimes removal. The i.e.p. of samples varied regularly between pH=1.6-4.1, the weathered fractions being at the lower end of the pH scale. These values followed a pattern comparable with the flotation behavior of samples. A patchwise structure for coal surfaces determining the resultant disjoining pressure, which in turn determines flotation-non flotation relationships is postulated.

Jan 1, 1982

By J. C. Heter

Industrial Mineral Fillers, LLC. is in the initial stages of mining and processing Anorthosite (CASPAR TM) at its CASPAR mine located in Soledad Canyon, Los Angeles County, California The CASPAR is being mined from the Precambrian San Gabriel Anorthosite Complex of the western San Gabriel Mountains. Preliminary results suggest that CASPAR is a desirable alternative to silica sand used in construction applications, such as, stucco, grout, abrasives, and other uses including filtration and golf course recreation sands. With the use of standard ore dressing techniques, CASPAR is suitable for use as a filler in paint, plastics and rubber. Environmentally, CASPAR has advantages over silica sand, in that, there is no detectable Free Silca.

Jan 1, 1997

By P. G. Corser

A gold and silver open-pit mine located in northwestern Chile contracted ACZ in 1991-92 to assess the stability of their spent ore pile and to determine the cause and magnitude of cyanide contamination associated with leaching operations. The mine is a conventional open-pit located at an elevation of approximately 4,800 meters (m.) (15,744 feet). A spent ore pile is located approximately 2,000 m. southwest of the mine and approximately 1,000 m. northeast of the active pad and plant facilities. The pile was constructed on a gentle northwest slope dipping 12 to 13 degrees. The pile is bordered by a small river to the northwest and by a larger river to the northeast. Both rivers eventually flow into Bolivia. Heap leaching and processing commenced at the mine in 1988. Since 1988, nearly 6.0 million tons of ore at an average grade of 1.96 grams/ton (0.07 ounces/ton) of gold and 52 grams/ton (1.83 ounces/ton) of silver have been treated by cyanide heap leach methods with zinc (Merrill Crowe) precipitation. In approximately three years of operation, the mine has yielded more than 225,000 ounces of gold and over 1.5 million ounces of silver. Currently ore is agglomerated and hauled to the leach pad by truck and is top loaded to produce a 5-meter lift height. Four contiguous reusable (on/off) leaching pads were constructed with an asphalt layer above a carefully compacted sub-base of High Density Polyethylene (HDPE) liner and screened fines. Leach solution of pH 10-11 containing 1.2 to 1.5 gram/liter of cyanide is applied to the heap at a rate of 10 liter/hour/square meter for a total active application period of 30 days. Leached (spent) ore is transferred to the spent ore pile located approximately 1,000 meters to the northeast. The pile currently contains approximately 6 million tons of spent ore. The pile liner, which has been constructed over a prepared sub-grade consists of three geosynthetic layers (geotextile/flexible membrane liner/geotextile). Long term objectives include washing the pile to recover an additional 3 to 4 percent gold and silver.

Jan 1, 1993

By Z. Jin, D. DePaoli, P. Zhang

"Phosphogypsum is a byproduct created during the production of industrial wet-process phosphoric acid. This study focused on recovering rare earth elements (REEs) from a Florida phosphogypsum sample and investigated the effects of removing detrimental impurities such as phosphorus pentoxide (P2O5 ), uranium (U) and fluorine (F) during the leaching process. Experimental results indicated that REE leaching efficiency increased rapidly, reached a maximum and then began to decrease with sulfuric acid concentrations ranging from 0 to 10 percent and temperatures ranging from 20 to 70 °C. At a sulfuric acid concentration of 5 percent and leaching temperature of 50 °C, REE leaching efficiency obtained a maximum value of approximately 43 percent. Increasing the leaching time or liquid/solid ratio increased the leaching efficiency. The leaching efficiencies of P2O5, U and F consistently increased with sulfuric acid concentration, temperature, leaching time and liquid/solid ratio within the testing ranges. A fine-grain gypsum concentrate, sized smaller than 40 µm, was separated from leached phosphogypsum through elutriation, in which the P2O5, U and F content levels were reduced by 99, 70 and 83 percent, respectively, from their content levels in fresh phosphogypsum. IntroductionPhosphogypsum is a byproduct generated during the industrial wet process of phosphoric acid production, in which sulfuric acid is used to digest phosphate rock. Gypsum (CaSO4·2H2O), the main component of phosphogypsum, usually accounts for 65 to 95 percent of phosphogypsum by weight.There are small quantities of impurities in phosphogypsum, such as phosphates (H3PO4, Ca(H2PO4)2·H2O, CaHPO4·2H2O and Ca3(PO4)2), fluorides (NaF, Na2SiF6, Na3AlF6, Na3FeF6 and CaF), sulfates, trace metals and radioactive elements (Rutherford, Dudas and Arocena, 1996). Global phosphogypsum generation is estimated at 200 Mt/a (Parreira, Kobayashi and Silvestre, 2003; Yang et al., 2009), but only about 15 percent is recycled as building materials, agricultural fertilizers or soil stabilization amendments (Tayibi Choura and Lopez, 2009)."

Jan 1, 2017

By John W. Stevenson

At the No. 4 Mine of Jim Walter Resources in Tuscaloosa County in the North Central part of the State of Alabama, the Mary Lee and Blue Creek coal beds lay 2000 feet below the surface. The quantity of methane gas stored within the coal bed reservoir at this depth and released during development mining necessitates that each coal producing section be ventilated using large air quantities approaching 100,000 cfm. In order to meet coal contractural commitments in the early stages of mine development by installing the necessary number of continuous mining machine units and to develop the mine to projected air shaft sites, high pressure, large volume mine ventilating fans were required. This presentation discusses the installation start-up and changeover procedures when two size GAF 31.5-28-1 TLT-Babcock 3500 Horsepower fans with adjustable pitch in flight blades were put on line while phasing out two Jeffrey Mining Machine Company 8HUA 117 Fans. A graph will be presented to depict the most economic diameter shaft size under 2000 feet of cover with different air quantity requirements.

Jan 1, 1982

By T. Tamagawa, I. Iwasaki, N. X. Fu, M. Kobayashi

A three-stage fluidizing-bed process consisting of chlorination, selective oxidation and sulfur chloride conversion was tested for processing chalcopyrite concentrate. It was found that the use of excess oxygen was essential for the stable operation of the oxidation reactor. The excess-oxygen gas inevitably causes the oxidation of the sulfide concentrate in the chlorination and sulfur chloride conversion reactors. A new flowsheet is proposed to separate the chlorination and selective oxidation steps with separate flow paths of the fluidizing gases, thereby, preventing the passage of excess-oxygen gas in the chlorination and sulfur chloride conversion reactors. The feasibility of the proposed flowsheet was demonstrated in a laboratoryscale fiuidizing bed setup.

Jan 1, 2002

By M. W. Harmer

Laboratory test work, pilot plant testing and plant experience with wet, fine mesh screens is discussed. High frequency, low amplitude, fine mesh, wet screens were installed on the 6th cleaner concentrate stream. These screens produce a 60% oversize recovery split of the molybdenite concentrate that is of leached equivalent quality. The undersize stream is leached with &apos;hot ferric chloride to remove Pb and Cu contaminates before roasting or shipment to sulfide customers. This plant modification is a good example of using existing technology in an unconventional flow sheet to yield significant cost savings.

Jan 1, 1990

By W. L. Price

I. INTRODUCTION Today, there are two conflicting trends facing the designer of the bulk material handling system. The first trend is the necessity to stockpile increasingly larger amounts of bulk material (coal, ore, stone etc.) as economically as possible. Fig. 1 illustrates such a typical large storage pile. The second trend is the increasing awareness of the ecological problems of today manifesting itself in a new concern over possible air pollution from storage pile surface particles. The conflict between these two trends can become dramatic when this bulk storage pile is located near a heavily populated area. Strong winds can easily create a severe local problem by blowing the particles from the pile surface toward residential and commercial areas, igniting a crisis in public relations. (2), (3), (4). To help define our combined subject and ecological culprit more accurately, Fig. 2 shows the commonly accepted size range of dust particles. A descrip¬tion of the present state-of-the-art of dust control for large storage piles is the intent of this paper. II. OPEN STORAGE PILE SYSTEMS - ALTERNATE CHOICES AND RELATIVE COSTS In discussing the open storage dust problem and possible solutions, one obvious question arises - what are the economics of placing large bulk storage under cover? Part or this answer will be found in Fig. 3 - an approximate unit capital cost comparison between several methods of storage. It will be noted that the cost curve(s) for the closed concrete silo storage illustrated in Fig. 4 is cheaper per ton at relatively small tonnage capacities, but as tonnage increases, the open pile storage unit cost (B) becomes more economical. Curve (T) covers the cost of open storage using the plow feeder arrangement shown in Fig. 5. A gravity draw-down pile with feeders at the base as shown in Fig. 6 represents yet another open storage choice.

Jan 1, 1972

By Ulrich Benatzky

Rheinbraun AG, Germany, is the management company of the mining and raw materials division of RWE AG. Rheinbraun&apos;s core business and major functional area is opencast lignite mining in the Rhineland. The characteristic feature of opencast mining is continuous operation using bucket-wheel excavators, belt conveyors, and spreaders. The report gives a survey of the conveyor systems used. In addition to the general performance data of these belt conveyors, this report will deal in particular with major components, such as drive stations and individual mechanical components (e.g., conveyor belts, pulleys, gears, couplings, brakes, scrapers), as well as monitoring systems. Finally, an assessment of the conveyor systems, together with future developments, will be given.

Jan 1, 2000

By Downing Terry L.

Dry mineral beneficiation methods have been developed for separation of borate minerals from montmorillonite claystone gangue. The methods include the use of newly developed dry high intensity magnetic separators. The application of these methods has the potential for economic benefit at U.S. Borax Inc. in three areas: ? Processing surface impoundments (ponds) material. ? Pre concentrating ore to be fed to primary refinery. ? Concentrating borate minerals to produce potential products.

Jan 1, 1995

By S. Phillipson

The Mine Safety and Health Administration’s Roof Control Division (RCD) evaluated the use of Shuttle Radar Topography Mission (SRTM) data to identify fracture traces on Earth’s surface. Results were compared to the analysis method employed by RCD for 30 years, which relies on LANDSAT-TM Band 4. SRTM elevation models are expected to provide a direct representation of bedrock surface, while LANDSAT-TM Band 4 represents reflected near-infrared radiation as an indication of moisture content and is only a proxy for possible structures. Three areas in southwestern Pennsylvania were chosen for ground-truthing lineaments derived from both methods, following a series of desktop comparisons in six areas of the contiguous U.S. Field studies that identified numerous instances in which SRTM lineaments corresponded with joints at the projected location, and were oriented within 10° of joint strike, indicating that those SRTM lineaments represented the structural grain of the area. In some cases, lineaments were associated with individual joint zones. Photo-lineaments derived from the existing LANDSAT-TM methodology appear to offer a higher coincidence with expected trends of joints on a regional scale when performing the desktop comparisons, while field observations indicated that SRTM-derived lineaments had a higher association with individual geologic structures in the case study field area. It appears that both methods can identify the structural grain of an area, and that both tend to identify linear segments of valleys where erosion has preferentially occurred along joint zones or other structures.

Jul 1, 2023

By G. Vallebuona

Currently, empirical models are used for predicting the hydrocyclone performance in terms of capacity, cut size (d50,c), water split and partition curve. These models, for example those of Lynch and Plitt, have been developed and checked for hydro cyclones with diameters larger than four inches. For smaller diameter hydrocyclones little empirical modelling has been done. This paper reports extended experimental research on small hydrocyclones. For these cyclones, the suitability of existing empirical models has been checked and their accuracy compared. Modifications of the existing models equations are proposed, improving their predictive capability for the small cyclones performance.

Jan 1, 1994

Gaby Copper Mining?s Gabriela Mistral property is located in the Antofagasta region of northern Chile, at an altitude of 2,660 m (8,727 ft) above sea level. The reserve contains an estimated 562 Mt (620 million st) of oxide ore with an average grade of 0.41 percent total copper. The mine went into production in 2008. Gaby Copper faced the problem of having no reliable way to measure the solids level. This is a challenge that exists throughout the mining industry, where dust in the air and accumulation of solids on a sensor make accurate measurements difficult in areas such as transfer chutes, the rock box underneath crushers, silos and anywhere else that information is needed on the level of solids. The next-generation technology in the Sitrans LR560 radar from Siemens addresses this challenge. With a frequency of 78 GHz ? higher than previous generations of radar ? it provides a more robust signal for measuring in areas where there are high levels of dust accumulation. The Sitrans LR560 provides a signal beam angle of four degrees, significantly narrower than any other product on the market can offer.

Jan 1, 2014

By M. L. Smith

SAG mill throughput is often a bottleneck in increasing metal productivity. Improved size distribution control in the mill feed can be used to increase mill production. This can be accomplished by controlling blast fragmentation as a function of energy input and rock characteristics. Such an approach requires the integration of rock fragmentation and comminution modeling. The optimal mill feed size distribution is determined by adapting a population balance comminution model to a measure of rock hardness or fragility which is also relevant to the rock fragmentation that is achieved by blasting. The relation between the size distribution and fragility of the feed and of the mill&apos;s product and the critical size in a SAG mill is examined.

Jan 1, 1993

By Rudolph H. Jacobson

The leaching of heaps or sub-marginal waste ore dumps as it is practiced throughout the Southwest as well as other parts of the world, is the major method of secondary recovery of copper. In 1970, twenty percent of all domestic copper was produced by dump leaching operations (l). In recent years, this method has been successfully extended on a limited scale, for the recovery of uranium from low-grade ores (2). It is inevitable that this technique will be increasingly employed in metal production to satisfy the insatiable demand of our mineral based society. Although dump and heap leaching has been used effectively for some time (3) , its application has been more of an art than a science. Therefore, it is essential that we learn about the important factors and parameters affecting this versatile process so that we may make increasing use of this technique in the future. The dump or heap leaching process encompasses the preparation of ore for-subsequent inplace leaching, the flow of solutions and ionic species through porous rock masses, the leaching of minerals with inexpensive and, if possible, regenerable lixiviants under prevailing conditions of the inplace environment, and the recovery of metals from the pregnant liquors. It is evident that this comprehensive scope of dump or heap leaching falls under the realm of interdisciplinary science and engineering requiring the application of the principles of physics, mineral engineering, hydrology, computer modeling, operations research, economics, and allied disciplines. An exhaustive study of the phenomenology of a leach dump or heap requires detailed knowledge of the simultaneous interaction of&apos;

Jan 1, 1972