Search Documents

By S. Möllerherm

"Since the adoption of the Rio-Declaration in 1992 the concept of sustainable development is raising more and more awareness in public perception. The World Commission on Economic Development WCED has defined sustainable development as the concept that "meets the needs of the present without compromising the ability of the future generations to meet their own needs". The concept requires the integration of economic, environmental and social considerations into all decision making, fostering intra-generational equity through the alleviation of poverty by concentrating the benefits of development in lesser developed areas; and considering the needs of future generations to ensure that inter-generation equity exists. This paper is devoted to give a review of the current status quo of the discussion. It describes the achievements of the mineral industries on their progress towards sustainable development since the Milos Conference (SDIMI 2003), but also discusses future challenges and obstacles."

Jan 1, 2005

By Z. Eisenstein, H. Heinz

INTRODUCTION Contemporary underground transit systems often require cross sections which are not adaptable to shield tunnelling. Due to the frequently large dimensions of these cross sections, which are normally situated at shallow depths and in soft ground, full face advance is not feasible because of ground control and construction requirements. Ground deformation and face stability are controlled by "staged excavation", which consists of sequentially driving smaller, specially arranged, individual headings hence avoiding full-face excavation. Shotcrete is normally used for initial support and these tunnels are frequently described as applications of the New Austrian Tunnelling Method (NATM). Figure 1 illustrates the relative size of large cross section tunnels with respect to conventional shield tunnels. Within the scope of this paper, 'large' cross sections are defined as those whose continuous (i.e., without intermediate pillar support) cross sectional excavated area exceeds 60m2. This definition includes most double track highway, railway and subway tunnels, subway stations and some single track railway tunnels. Excavation schemes which have been more frequently used for continuous cross sections (i.e., with no intermediate pillars) are presented in Figure 2. This classification is an extension of that presented previously by Eisenstein et al. (1986). The symbols used for classifying the excavation schemes are formed by the letter T (for "type"), followed by a number, which represents the number of excavation stages fully embraced by a shotcrete ring, termed "cells" by Lessmann (1986). The numbers inside the cross sections in

Jan 1, 1989

By Alena Conrads, Markus König, Markus Scheffer, Markus Thewes, Hannah Mattern

"INTRODUCTION In recent years, the development of tunnel boring machines has revolutionized the tunneling industry. The general structure of a tunnel boring machine (TBM) can be described as a multi-component system. To achieve high performance rates, machine elements have to perform reliably. Performance losses and interruptions of the construction process should be prevented or at least, reduced to a minimum. In order to achieve high advancing rates, cutting tools must be in good condition at any time. Furthermore, failure of individual tools might result in increased and faster wear of remaining structural components. For this reason, maintaining and replacing cutting tools is crucial to prevent project delays due to insufficient boring performance. Precise prognoses concerning the prevailing geology are infeasible and thus, efficient scheduling of maintenance actions is challenging. The intention of this work is to analyze different approaches of TBM maintenance in soft ground. Different strategies are analyzed by the use of a simulation approach. Cutting tool condition is regarded as performance limiting factor. The maximum operation time of the cutting tools is determined using the “Soil Abrasivity Index”. A case study serves to show the effects of different maintenance strategies on total project duration. SCHEDULING OF MAINTENANCE ACTIONS Scheduling maintenance actions of single and multi-component systems concerns numerous fields of industrial production. Concentrating on mechanized tunneling in soft ground, cutting tool maintenance represents the most common reason for intermission of advance (Köppl 2014). In literature, time-based and condition-based maintaining techniques are widely discussed. The following section outlines the principles of time- and condition-based policies. Furthermore, examples for their applications in recent research are given. Time-Based Maintenance In general, the time-based maintenance approach assumes that the failure behavior of the system components is predictable. Maintenance actions are scheduled according to predefined intervals (e.g., hours, days, weeks). A detailed analysis of preventive repair times or interval forms the basis for maintenance decisions. For this approach, an adequate quantity and quality of data is fundamental. Numerous studies deal with the analysis of time-based maintenance for production equipment. In fields of mechanized tunneling, unplanned machine downtimes restrict the applicability of time-based maintenance approaches. Thus, this paper mainly focuses on condition-based maintenance."

Jan 1, 2016

By David J. Akers

INTRODUCTION The variety of uses of coal and the wide range of characteristics of coal combine to produce a need for a wide variety of laboratory analysis. Coal is used to heat homes, produce electricity, and make coke for steel manufacture. It can also be used to produce both gaseous and liquid fuels as well as a variety of chemical products. Various applications may require specialized analytical procedures. For example, some of the procedures developed for the coke industry, such as expansion or contraction during carbonization, have little value to the power generation industry. Even for a single application, the type of analysis needed can depend on the source and/or general nature of the coal. This section provides a general overview of the types of analytical procedures commonly applied to coal from the perspective of the user of this information, not the producer. The intent is not to detail laboratory procedures, but rather to discuss the application of commonly used laboratory tests in coal preparation. Accordingly, laboratory procedures are categorized by type of information produced. Gravimetric Analysis Procedures that produce weight-based information (parts per million, pounds per cubic foot, or weight percent). Such analyses can relate to the coal's physical, chemical, or mineralogical characteristics. Volumetric Analysis Procedures that produce volume-based information (amount of a mineral present as a volume percent). The primary source of volumetric information is from petrographic analysis. Application Tests Procedures that measure some characteristic of coal that has been empirically related to some application or handling or processing step. Typically, these procedures attempt to duplicate some aspect of the commercial application at laboratory scale and may produce information in the form of an index. Applications procedures do not measure a single component of the coal but infer the combined effect of multiple components. Each class of information is discussed in the order listed. References are provided as a source of more detailed information. The American Society for Testing and Materials (ASTM) publishes the most inclusive reference to analytical procedures. This publication,16 which is revised annually, provides extensive information concerning generally accepted methods of laboratory analysis. ASTM also provides standards for sampling and some information concerning sample handling.

Jan 1, 1991

By William E. Hole

The sand and gravel industry provides an enormous quantity of materials vital to the maintenance of low-cost construction. There has been little effort to conserve this valuable natural resource. In fact, existing regulations which affect sand and gravel operations act more to waste these materials than to conserve them. Another factor affecting the industry is new legislation requiring the reclamation of worked-out pits. Although such legislation creates many administrative headaches for a sand and gravel operator, there exists the possibility through such legislation of gaining some conservation measures that could be helpful to the industry.

Jan 1, 1974

By L. B. Bramlett

The Archean (2.65 b.y.) aged Canning Stock at Copper Mountain, Wyoming contains an average of 20 ppm U. The North Canning and Fuller deposits occur within the enriched interior of the stock. Post-Laramide development of super gene enrichment blankets occurred in wide (25- 100 m) crushed zones. Hematite and chlorite accompany pyrite and sooty pitchblende in the mineralized zones. Reduction mechanisms proposed for deposition of pitchblende are: 1) sulfides, 2) hydrocarbons, 3) bacteria, 4) the water table, or 5) some combination of these. Abundant tar- type organics appear to have preserved the enrichment blankets from degradation. Trace element and radiometric data define target zones, but exploration models focus on favorable structure.

Jan 1, 1980

By Edward M. Downs

This paper is a brief review of the lubrication requirements of enclosed gearing on earth moving equipment, particularly as they apply to intermediate and large draglines and shovels used in open pit mining operations. It discusses the requirements of spur, helical and herringbone gearing in both horizontal and vertically mounted applications. The effects of base stock, oil viscosity, additive treatment, quantity of oil and method of application are considered. In addition, a newly designed circulating oil system for enclosed swing gear cases and the reasons for its development are discussed.

Jan 1, 1968

By J. D. Patsey, G. T. Lineberry

A.E. Hall The authors are to be commended for their attempt to provide a convenient piece of software for preliminary drum hoist specification. This field has received little attention in recent years and is eminently suited to calculation by computer. Unfortunately, there appears to be an error in the calculation of the required rope diameter. The 66-mm (2 5/8-in.) rope selected is oversized for this application. Wire rope weight and breaking strength are related to the rope diameter. For a round strand rope

Jan 8, 1987

By E. A. Metz

It has been approximately four years since the International Agency for Research on Cancer (IARC) reclassified crystalline silica as a "group one" substance. Since then, crystalline silica has been considered a human carcinogen. Silicosis is a preventable disease, and several aggressive campaigns have been developed to increase awareness of silica-dust-related problems in the industrial environment. New analytical techniques are now being developed to determine quantitatively the amount of crystalline silica in materials. Yet, still much is to be learned about the surface properties of silica and the way in which the disease progresses into full-blown silicosis. This paper discusses the interaction of free radicals generated by the mineral particles and lung tissue. It is the cell injury and DNA damage that progresses to fibrogenesis. Freshly fractured surfaces of silica contain free radicals. These free radicals play an important role in the stimulation of the alveolar macrophage and the development of the inflammatory reactions leading to the fibrotic response caused by silica. Engineers, scientists and physicians need to discuss the mineralogy of silica and the technical issues concerning the development of silicosis.

Jan 1, 2000

By K. K. Wu

In some cases, coal barrier pillars must be relied on to withstand high hydrostatic pressures in order to prevent inundation of active mine workings. Such barriers are particularly important in areas, such as parts of West Virginia, where much of the future mining is down dip of mines which have been abandoned, or are currently being worked. Also, where multiple seam mining is conducted, a barrier pillar in one mine may be critical to safety in a mine in a lower seam. MSHA's Coal Mine Safety and Health district offices and the Mine Waste and Geotechnical Engineering Branch of the Pittsburgh Technical Support Center, have recently been involved in the study of barrier pillars in Kentucky, Virginia, West Virginia, Ohio and Oklahoma. In this paper, the factors involved in determining the required width of pillar are discussed, past practices for sizing barriers are reviewed, and related current Federal regulations are examined. In addition, the results of laboratory testing of bottom rock are presented.

Jan 1, 1980

By S. K. Nicol

The results of column flotation tests conducted on a bulk sample of ultrafines discarded from the fine coal desliming cyclones at the Riverside coal preparation plant of Theiss Dampier Mitsui Coal Limited are presented. A 9% ash concentrate was obtained from a 51% ash ultrafine feed at 75-80% recovery of combustibles in a single stage of column flotation. From this result it is predicted that installation of column flotation at Riverside would lead to the annual recovery of additional coal worth $US5.1M. The operating conditions for coal and copper column flotation are compared and some differences which may result in a variation in column design are noted.

Jan 1, 1987

By C. H. Pitt

A jet slurry apparatus has been constructed to test corrosive/erosive wear properties of grinding ball metal. Plain high carbon steel heat treated to a hardness of about 60 RC was used. Slurries of quartz and chalcopyrite ore concentrate were used as the jetting media. Weight loss due to pure corrosion was determined by the linear polarization technique and weight loss due to pure erosion was determined by jetting while cathodically protecting the sample. By comparing the total weight loss with the sum of the weight losses from pure corrosion and pure errosion it was found that there was a synergistic effect between corrosion and erosive wear. Erosive wear rates are given as a function of pH and mineral type.

Jan 1, 1984

By V. D. Ayurov, N. O. Kaledina

The coal mines monitoring should be based on the usage of simple and evident models, letting in the total unity to reflect a structure of organization of mine, system ability of its construction and specific character of its functioning. Such models are offered to create on the basis of extracted hierarchies of objects of mine. All objects of mine are broken on levels of technological hierarchy. For objects of each level of hierarchy there are made balanced models of entering and leaving material flows. Then these balanced models are coordinated among themselves by the help of the inter hierarchical relations. So the structured-qualitative characteristic of the object of monitoring, reflecting in a kind of the table structure of formation of material flows on mine, their intensity and measure of transformation is formed under transition from one level of hierarchy of mine to another. An example of real us- age of hierarchical balanced models on mine is given. The mathematical models of coal mine monitoring should reflect objective laws of their structural organization and functioning. Therefore under the constructing of mathematical models it is important such a way to reflect a structure of the mine organization, that in totality the models has been reproduction of system ability of its construction. The knowledge of the separate parties of functioning of mine, reflected in particular mathematical models, should "to be packed" in combined unity. Or else, they should be connected in system, convenient for recognition by the person. Considering the mine, the expert allocates multi-dimensionality of the objects of making its elements. He always has the knowledge of laws of development of mining work that is connected with pithy stratification of researched object. In dependence of sparial-temporary level of abstracting there are allocated the horizon, wing of a mine field, layer, panel, extracting face, longwall in coal mine. The human thinking on each of these levels operates with a set of concepts peculiar to him, characteristics, definitions.

Jan 1, 1996

By Rodger C. Smith

The topic chat has been assigned to me ?Economic and Political Climate of the Potash Industry? is a function of two basic facts: 1. Potassium is absolutely essential to plant and animal growth. Along with nitrogen and phosphorus it is one of three major plant nutrients, the three nutrients required in largest quantities for plant growth. 2. United States is unequivocally an "have not" nation with regard to potassium. Quantity of potassium ores is limited and, more disturbing, the cost of production at all U.S. potash mines is marginal in comparison with the major producing countries, i.e. Canada and U.S.S.R.

Jan 1, 1983

By Ralf Vergeiner

The most famous landmark of the city of Graz (Austria) is the clock tower on the castle hill. An underground chamber was built as a multifunctional structure beneath this landmark. The required structure was designed as cavern. The overburden to the clock tower in the north side of the cavern was only 30 m. To allow access from the city to the chamber and the clock tower, a vertical shaft was built near the cavern. Rock excavation was by drill and blast method. The pilot shaft was made by the raise-boring method. Because the location of the building site was in the center of Graz, special care was taken to minimize deformations and vibrations so as to protect surrounding buildings.

Jan 1, 2001

By D. O. Miller

The effective staffing of personnel in a new concentrator facility is a key factor in the success of the operation. By selectively recruiting quality individuals, a company is in a strong position to build a positive work ethic which will become an integral part of it's culture. And culture, which is a set of standards that all employees work to uphold, is that intangible as- set that often determines whether or not a company will survive during difficult economic times. Recruiting and placement of personnel in a concentrator facility requires an emphasis on planning. Management must carefully analyze the following elements when designing a hiring plan: 1. Number of positions 2. Hiring schedule (timetable) 3. Critical positions 4. Lead-time for trainee posit ions 5. Characteristics of the ideal workforce This presentation will focus on a proven system that is efficient (and yet simple) for achieving a new concentrator facility's manpower requirements. IDENTIFYING THE STAFFING NEEDS As previously stated, the key to staffing is planning. Management will find that a basic manpower chart will provide the hiring schedule to meet deadlines. In fact, this system begins with a manpower chart (Figure 1). The chart basically works in reverse of the hiring requirements: the last scheduled hire is the first job on the list. This approach ensures that the company will not find itself compressed against the facility start-up date. A cardinal rule in recruiting a workforce is to allow sufficient time to orient and train employees to the procedures and culture of the system. Problems in selection of personnel begin when the hiring program is short-circuited for timing reasons. The quality of employee selected invariably suffers accordingly. The second section is the key to the success of the manpower program. This is the latest date by which a formal recruiting effort must begin in order for the hire date to be met. Leadtimes are usually as follows: 1. 90 days for company transfer positions 2. 60 days for experienced new hire positions 3. 30 days for trainee positions

Jan 1, 1986

By Clete Stephan, John Urosek, Ian Anderson

The Endeavour Colliery is operated by Powercoal Pty Ltd. It is located in the Central Coast of New South Wales, Australia. The mine has been in operation for about 30 years, producing around 600,000 tons of export coal annually from two production sections. On June 28. 1995, an explosion occurred underground in the 300 Panel at approximately 9:50 a.m.. There were thirty miners underground at the time of the explosion, all of whom were safely evacuated. From June 29 through July 10, personnel did not enter the mine. However, gas samples of the mine atmosphere were obtained from underground monitoring stations and analyzed. Samples were also obtained from boreholes that were drilled from an adjacent mine. On July 10, the atmosphere at the underground monitoring locations and at the boreholes appeared stable with minimal risk of combustion occurring underground. Plans were developed to begin the recovery of the underground workings. The recovery of the underground workings was completed on July 13. The underground investigation of the explosion began on July 14. The investigation was conducted by the New South Wales Department of Mineral Resources. Technical assistance was pro- vided by the United States Department of Labor's Mine Safety and Health Administration (MSHA).

Jan 1, 1997

By M. Modis

According to previously established theoretical analysis and under certain conditions, a critical sampling grid can be determined for an earth-related space-distributed natural variable. Sampling above this critical limit adds little to the mapping results, while based on this limit the ideal process of reproducing the original phenomenon is theoretically defined. The objective of this paper is the application of the above theory to the Klidi lignite deposit in Florina, Greece, where Public Power Corporation (Greece) has conducted a sampling campaign to estimate the deposit thickness and its heating value. Data acquired for these two variables were analysed in the space domain in order to derive their respective correlation functions. The structural analysis of the deposit generated two covariance models, one for the thickness and one for the heating value, from which the critical sampling grid was identified. The conclusion drawn is that in some parts of the deposit the sampling grid is denser than required. Finally, an optimal sampling grid is proposed in order to gain the maximum information at the lowest cost.

Jan 1, 2006

By Michael L. Maniocha

Most magnesia (MgO), whether of natural or synthetic origin, is used in the dead-burned or periclase form as refractory linings for the production of steel. Continued research in refractory science, combined with good refractory maintenance and improvements in steel-making processes, have resulted in decreased use of magnesia. To make up for this loss of business, producers of synthetic magnesia have started to manufacture a variety of magnesium-based chemicals that are used in many industries. There are three primary methods of producing MgO. The first involves the calcination of naturally occurring minerals species. Most of the magnesia produced by this method uses the rhombohedra1 carbonate mineral magnesite, MgCO,. To a lesser extent, the mineral brucite, Mg(OH), is calcined to magnesia. Magnesia produced by the calcination of minerals is called natural magnesia. The second production method uses magnesium-rich brines, or sea water reacting with lime or calcined dolomite to produce magnesium hydroxide. The magnesium hydroxide is subsequently calcined to magnesia. Material produced in this way is called synthetic magnesia. The third major method of production uses saline lake brines to produce magnesium chloride. Magnesium chloride brine is sprayed into a reactor where it thermally decomposes into MgO and HCl. The magnesia is purified by slaking to magnesium hydroxide followed by calcination. Magnesia produced in this manner is also know as synthetic magnesia (Duncan and McKracken, 1994). The degree to which the magnesium minerals or the synthetically prepared magnesium hydroxide is calcined governs the physical properties of the resulting MgO. It is the physical properties that dictate the end use for the product. The terms used to describe magnesia vary along with the degree of calcination. Table 1 summarizes the terminology used when discussing the various forms of magnesium oxide.

Jan 1, 1997

By K. Pietruszka

The article presents the concept of the application of the Finite Element Method (FEM) and ABAQUS software in the global monitoring of changes in the rock mass and on the surface of the area, as a result of backfilling the workings. Waste materials applied for stabilizing old mining workings can have a strong influence on the rock mass and surface. According to the regulations, this process should be carefully monitored, especially in terms of the safety of surface structures and rock mass stability. The article presents the concept of an analytic and graphic presentation of the results of the measurements of old workings, applying the Finite Element Method and ABAQUS software in model studies. The main purpose of such interpretation of the geodetic observations results is the application of methods providing wide possibilities to present the geometry of workings, their changes and the influence of the rock mass and surface.

Jan 1, 2008