Search Documents

By Thomas E. Finch

Coal produced from surface mines in the Western United States is becoming a more important part of this nation's economy as other types of fuels become scarce. This paper reports the investigation of alternative methods of handling the parting between two coal seams. The results of this investigation are presented as the engineering-economic aspects of alternative parting handling methods involving stowing or back filling techniques. The coal and parting characteristics were selected as being representative of those under consideration or actively mined in the West. The basic philosophy of evaluation is to establish a mine-within-a-mine where equipment selected for minimal capital investment can remove the parting and second seam nearly independent of the ongoing, present production. With proper consideration of design, this parting-coal removal is evaluated as a second operation within the first and has its own profitability measure. The Fort Union Area of Montana, Wyoming, and the Dakotas contains large reserves of low sulfur sub-bituminous coal. In many locations, several coal seams are close to the surface and are separated by relatively thin layers of parting. The removal of overburden and the mining of the upper seam is accomplished effectively with conventional mining methods and equipment. Mining a second seam of coal and handling the parting in accord with economic and environmental controls presents a number of problems. Typically, mining companies have adapted the conventional strip mining techniques used in the East. However, the extreme thickness of the western coal seams offers alternative mining method possibilities for parting and second seam removal.

Jan 1, 1976

By Frederick McNeill, Mahmood Khwaja, Benjamin Lundsted, David Polcari, Michael S. Schultz, Timothy Clougherty

The City of Manchester, New Hampshire, is embarking on one of its largest public works projects in history to construct a 12,000 foot long, large-diameter, conveyance tunnel through downtown Manchester. This area has challenging geology with undulating bedrock (granite, schist, and gneiss) profile overlain by fluvial deposits. Understanding the subsurface conditions is key to mitigating project risks, establishing plan and profile for the tunnel, and selecting the most cost-sensitive and technically appropriate tunneling method. This paper presents the project team’s approach for conducting the ground investigation, developing preliminary subsurface profile, and the considerations for selecting the tunneling method.

Jun 13, 2023

By G. T. Lineberry

There is a critical need for effective instructional materials at the university level and for an upgrading of mine safety and health in the mining engineering curriculum. A fundamental approach to mine safety and health is recast into the familiar 3 E's: engineering, education, and enforcement, in that order. Each is briefly reviewed and their interdependence emphasized. A unique philosophy for successfully integrating safety and health principles into the mining engineering curriculum is offered. The concept of textbook ?tailoring? is discussed and defended, permitting rapid assemblage and synthesis of existing educational materials. Final recommendations are made for a u, comprehensive approach to mine safety and health education in the undergraduate curriculum.

Jan 1, 1987

By G. K. Derby

Paper presents project results investigating current techniques for dragline wire rope removal and the development of less hazardous means of performing the task. The cannon is the most prevalent method used in American surface mines. A cannon test program was conducted that used 40-and 50-grain primer cord to establish force produced using a 56-pound projectile. Socketlwedges were separated to establish separation force data. Two alternative removal methods, pendulum ram and portable hydraulic pusher, were developed and tested. Both provide sufficient force to effect separations under normal conditions on draglines with up to 78- cubic yard buckets.

Jan 1, 1984

By Peter C. Badgley

Three tectonic provinces within the Cordilleran System, are analyzed in terms of tectonic framework. (1) Precambrian terrain of North-Central Colorado; (2) The Pacific Northwest; and (3) The San Andreas-Garlock fault system and associated features. In each case a close relation- ship is seen to exist between: (I) Arcuate mountain development; (2) Precambrian basement fabric; (3) Major fault patterns; and (4) Major mineral occurrences. The arcuate trends developed when the basement was still mobile. Later competent deformation rejuvenated pre-existing lines of weakness. Because of the pre-existing arcuate framework, the rejuvenated faults frequently act as conjugate shears (strike-slip faults) flanking the old arcs. The conjugate shears intersect to form wedge- shaped plates. When such plates move forward along boundary strike-slip faults in response to post basement orogenic forces, new secondary fracture systems are generated in the country rock flanking the advancing wedge. The apex regions of the wedges are particularly favorable for detailed exploration.

Jan 1, 1959

By Karl C. Dean

The current emphasis on environmental problems has focused attention on the massive nationwide accumulations of mine, mill, and smelter wastes that represent potential air and water pollution hazards. The pollution hazards can be reduced or eliminated by utilization or stabilization of these wastes. The U.S. Bureau of Mines, since the inception of the Solid Waste Disposal Act of 1965, has been conducting research to determine the practicality of various utilization and stabilization procedures. Investigations include partial extractions of desirable waste components and full utilization of the wastes as simulated soils or in ceramic or other structural products. Chemical, vegetative, and combined chemical-vegetative methods of stabilization have been actively studied. This report updates information previously developed by the Salt Lake City Metallurgy Research Center and presents the current status of antipollution solid waste work 1/,2/.

Jan 1, 1970

By D. J. Lachel, Douglas E. Hansen, Bruce Kennedy

The very high cost of exploration and development for new mines requires that a carefully planned, complete, and technically competent geotechnical evaluation be applied to the ore body and the surrounding rock. The ground conditions must be predetermined sufficiently so that, during the development and exploitation stages, unexpected conditions will be of minor consequence. Ground conditions are a major factor affecting the cost of excavated items such as shafts and inclines. For example, shafts cost less to sink in tight dry ground than in highly pervious ground below the water table, with all other factors being equal. The proper mining methods also is dependent upon the ground conditions. Bad ground for room-and-pillar mining may be ideal for caving methods; whereas, ideal ground for room-and-pillar mining would be extremely difficult for a caving operation. To do a proper engineering design, the parameters of strength, deformability, and permeability must be determined, in addition to the loads that will be applied as a result of the mining activity. The required degree of accuracy for each parameter depends upon the individual case. For example, the strength of massive rock in which openings of small cross-sectional area are to be driven at shallow depths needs to be resolved only within several thousand kilopascals (pounds per square inch). Under such conditions, the rock strength is not likely to be of great economic importance unless the rock is very weak. Large openings at great depths require a much more accurate appraisal of rock strength and deformation characteristics. Ground water conditions are important at any depth. Today, a number of techniques exist for evaluating conditions before opening up the ground for development. These techniques and their applications are described in more detail later in this text. The evaluation of ore body ground conditions should start at an early stage, as soon as the deposit has been proven viable for a mine. Economic geology investigations mainly serve to define the value and limits of the ore deposit. To do this properly, the geology of the site is determined in at least as much detail as is necessary to define the "controls" for the ore body. The ground-condition evaluation must determine the engineering properties of the ore body and the surrounding material. This includes the structural geology as it relates to rock strength; i.e., the frequency, extent, and orientation of discontinuities such as faults, joints, bedding, etc. Ground water conditions also must be determined. It is important that the detailed geology of the site be determined at an early date. Reasonable geotechnical parameters must be established during this time period, so they can be used in mining model studies that include both physical and mathematical models. The ultimate goal bf-the geotechnical evaluation is to predict the ground behavior as the excavations are made and how the ground behavior will affect the safety and economic well-being of the mine. The formulation of a ground-condition evaluation program should be planned carefully to determine the particular geotechnical parameters only in as great a detail as will have a bearing on the mine design. For instance, it is not necessary to make numerous triaxial tests in strong rock when the mining will be conducted within a few meters (feet) of the surface in a regime of gravity loading and an absence of tectonic stresses. Similarly, it is not necessary to invest large amounts of time and effort in the determination of joint strengths if the orientations of the joints are such that the failure could not occur along them. Generally, the determination of ore body ground conditions can be divided into four main steps: 1) The general and structural geology of the site must be determined; this is determined primarily during the economic evaluation. 2) The material behavior characteristics of the deposit and the vicinity must be determined. 3) The ground water hydrology of the deposit and the vicinity must be determined. 4) Miscellaneous ground support considerations must be established. Gross features are defined first, followed by a series of increasingly detailed investigations. Specifically, the geology study should start by utilizing techniques such as remote sensing, topographic map interpretation, geologic mapping, etc. After the gross features, such as major faults, have been delineated, the studies are directed toward defining the more detailed elements of jointing, rock strength, ground water hydrology, and other characteristics. This information is used to formulate an assessment of the strength of the ore body and the surrounding rock. Finally, all of the gathered information is integrated to make an assessment of the rock behavior in relation to the types of openings, the excavation methods, the support requirements, etc., that should be used for the rock conditions that are present. The mine design and the geotechnical assessment should be an iterative process. General conclusions about the rock conditions will dictate a type of mine plan. The specific mine plan then should be modified by specific geotechnical considerations. For example, an initial assessment may conclude that the ore body is strong and that a strong rock unit is present over the ore body. Thus, one definite possibility is to mine the deposit by room-and-pillar methods. However, subsequent investigations may reveal faults through the deposit, requiring relocation of the mine openings so that pillars and other structures are in sound rock. In other words, the final mine plan should be compatible with the geotechnical aspects of the ore body.

Jan 1, 1982

By Hans Smit

The face of mining as we know it is set to change in the very near future as mining companies all over the globe realize the implications of accessing the vast mineral wealth contained on, and under, our ocean floors. With some land based mineral deposits being fully exploited across the world, deep sea mining is set to revolutionize global approaches to the search for precious metals and other sought after minerals. [ ] Previously, the financial implications of deep sea mining outweighed the benefits of access to the mineral rich deposits identified all around the world. The process of marine diamond mining off the west coast of southern Africa started in the late 1950?s by a Texan, Sammy Collins, and subsequently continued by De Beers to the present day, has proven to be an excellent proving ground for the development of technology and mining systems that ensure a sustainable and financially viable business. [ ]

Jan 1, 2008

By M. R. Moon

The mine fire at Wilberg Mine in 1984 reached the surface resulting in the failure of the vertical ledge forming the roof and entrance for three main intake portals. The fallen material was covered with a concrete cap to seal the air from the mine. As the mine was recovered and ventilation pressure was placed on seals on the perimeter of the fire area, the concrete capped rubble proved ineffective. Due to the steep and rugged terrain and the inaccessibility to the portals from underground, horizontal holes were drilled into the portal entries and three seals were placed remotely. The seals in conjunction with pressure balancing the seals around the perimeter of the fire area resulted -in the control of the mine fire.

Jan 1, 1993

By W. Jacobi, F. Steinhausler, A. C. James

INTRODUCTION In 1979 the Committee on Radiological Protection and Public Health of the Nuclear Energy Agency (OECD) defined a programme of work needed to improve radon dosimetry and monitoring. A Group of Experts in this field was established by the NEA and at the first meeting of the Group the authors were designated an initial task with the following terms of reference:- To review dosimetry of radon, thoron and their daughters, and in particular:- - to examine analytical models for the assessment of dose to individuals who are exposed to aerosol mixtures of these nuclides; - to examine the state of knowledge of the characteristics of aerosol mixtures of these nuclides and other factors that influence the dose to the lung, and identify those parameters which should be measured for dosimetric purposes in radiological surveillance programmes; - to identify areas where further study or research are needed. In this presentation we attempt to examine, with these objectives, the relationship between exposure to radon and thoron daughter aerosols expressed in terms of the working level month l (WLM), or its SI equivalent, and dose accumulated by sensitive tissues of the lower respiratory tract. Over the past two decades many attempts have been made to calculate the lung dose equivalent to l WLM exposure in mine atmospheres, usually in terms of the maximum dose to basal cells in a small part of the bronchial tree. The calculations have employed variously detailed models of airway anatomy, aerosol deposition, ciliary clearance and dosimetry of tissue at the bronchial surface, and are well reviewed elsewhere (Walsh, 1970; UNSCEAR, 1977; Jacobi, 1977; Fry, 1977). They agree in the conclusion that basal cells in segmental bronchi (between about the third and fifth bronchial generations) receive the highest dose, although estimates of this dose differ by more than an order of magnitude, ranging from about 0.2 to 12 rads per WLM (2 mGy to 120 mGy). The most critical parameters of these models are the assumed depths of basal cells below the bronchial surface and the fraction of the WL carried by free ions. When more realistic values of these parameters are substituted (Jacobi, 1977), the dispersion in calculated maximum doses to basal cells is reduced to give a much smaller range from about 0.3 to 1 rad/WLM (3 to 10 mGy/WLM). The parameters and methods employed in these various models, however, remain too diverse to infer the sensitivity of the dose conversion to practical variations in aerosol characteristics and the additional factors determining lung deposition and clearance. We have therefore taken the approach of developing newer models (Jacobi and Eisfeld, 1980; James et al, 1980) that can encompass the range of available experimental data on the physical and biological behaviour of radon and thoron daughters and also accommodate the different interpretations that can be put upon them. We have paid particular attention to the averaging of dose over tissues of equal sensitivity in the lung

Jan 1, 1981

By Y. Akin, M. Hancer, M. S. Celik, J. D. Miller

Flotation pulps with boron minerals such as colemanite and borax using primary amine collectors, e.g. dodecylamine, exhibit collector precipitation above a critical pH depending on the amine concentration. This was earlier attributed to the formation of a mine hydroborate. However, results from this current study indicate that the precipitate is dode-cylamine, rather than dodecylamine hydroborate. A systematic study involving solubility, zeta potential, microflotation, adsorption, and surface tension measurements is presented to elucidate the role of a mine precipitates in boron flotation systems.

Jan 1, 2000

By J. G. Groppo

A beneficiation process has been developed to provide selective separation of unburned carbon from high loss-of-ignition (LOI)fly ash. Using froth flotation to achieve selective separations requires long residence times and high reagent costs. A proprietary reagent system has been developed to address these limitations. Based on the results obtained from laboratory and pilot-scale investigations, a flowsheet design has been developed to produce two distinct usable products from class F fly ash — low LOI ash and a high-carbon product suit-able for reburning or further upgrading.

Jan 1, 1996

By P. C. Thakur

Mine productivity, measured by the output of minerals per manshift, depends on a number of factors including physical conditions of the minable seam, type of mining equipment, management techniques, worker attitudes and governing jaws and regulations. The greatest scope of improving productivity lies, perhaps, in modifying physical conditions to an advantage and using highly productive equipment. In the case of coal mines, increased productivity can be achieved by (i) obtaining prior knowledge of the mineable property, e.g., the grade and thickness of, the coal seam, presence of sand channels, faults, etc., (ii) eliminating conditions that hamper production, e.g., high emissions of methane and water, and (iii) using more productive mining techniques. Conoco/Consol's (Conoco Inc. and Consolidation! bal Company, a fully-owned subsidiary) horizontal drilling system was developed with the hove objectives in mind. It can drill 75 to 1001 in diameter boreholes to depths of more than 600 1 and maintain the borehole in a preselected horizon. Such boreholes can be utilized for premining exploration of the coal seam, for removing methane and water and in devising mining techniques with high productivity. The purpose of this paper is to describe the horizontal drilling system briefly and to discuss its applications in the above-mentioned- areas.

Jan 1, 1980

By W. S. Sanner

Experiments were conducted to determine the quantity and purity of ultraclean anthracite that could be prepared in the laboratory, using conventional separating techniques. A low-, a medium-, and a high-volatile anthracite were studied. Specific gravity separation followed by grinding, screening, and refloating at lighter specific gravities yielded small quantities of material purified to 1.0 percent ash, as follows: From low-volatile anthracite, 0.7 percent; from medium-volatile coal, 1.0 percent; and from high-volatile coal, 2.3 percent. The reduction in ash had no appreciable effect on the volatile matter or sulfur content of the coal. The limited quantities of material containing 1.0 percent or less ash obtainable indicate that if ultraclean coal is desired, a practical approach should include the processing units as an integral part of a conventional dense-media washing plant.

Jan 1, 1968

By Robert Charles Alfred

Evolution is continuing in the field of rock drilling, Campbell Limestone Company is experimenting in the higher air pressure phase of drilling, It has been determined that there is a definite relationship between Air Pressure, Penetration Rate, Bit & Tool Wear and Life, In our drilling we have determined that &e higher air pressure gives a better penetration rate with less bit wear per foot. Drilling with 180 to 200 PSI air pressure, instead of 100 PSI for air and/or churn drills, has decreased our primary costs by approximately one half.

Jan 1, 1963

By T. Stuczynski

In the past ten years about 3000 wastewater treatment plants have been built in Poland. The result of this development has been a massive increase in overall sludge production. According to data supplied by the Ministry of Environmental Protection, 400,000 dry tons of sludge are generated every year in Poland (Koblak-Kalinska 1996). Still it is difficult to estimate the amount of sludge, which is used in agriculture or for reclamation purposes. However, it can be assumed that this comes to no more than 10 percent of all sludge produced in Poland on a yearly basis. Thus it became obvious that an urgent solution to this problem was needed. Local authorities in Silesia realized in the early 90?s that a demonstration was necessary to encourage the proper utilization of sludge. This was the basis for establishing the Biosolids Subpart of the Silesia Project, which addressed the use of biosolids in the reclamation of mining and smelting dumps (Stuczynski et al. 1996). Metal waste sites themselves are known to contain more than 87 million tons of waste (Pistelok et al. 1995). Each year this amount increases by approximately 400,000 tons. We realized that a simple solution for stabilizing these sites would be to cover them with vegetation in order to reduce leaching of toxic elements, as well as to keep metallic fugitive dust from entering the environment. The reclamation of smelter waste sites, which was carried out within the framework of the Silesia Project was a joint effort of local government, industry and international research institutions/agencies, including the US Environmental Protection Agency (EPA), the Center for Research and Control of the Environment (OBIKS), Virginia Polytechnic Institute and IUNG. One of the goals was to evaluate the possibility of adapting the rules of sludge management currently used in the United States to conditions commonly found here in industrial regions of Poland. However, the main objective of the Silesia Project was the development of guidelines concerning all aspects of sludge use for the reclamation of degraded lands and waste sites. Biological aspects related to reclamation of metal waste with the use of biosolids will be discussed in this paper.

Jan 1, 2002

By Yoginder P. Chugh

About 65% of the U.S. coal production (835 n tons was surface mined. A similar proportion of the Illinois basin's production (112 m tons) is also surface mined. The state of Illinois is the third largest producer of surface mined coal in the United States, after Wyoming and Kentucky. The Illinois coal basin encompasses Illinois, southwestern Indiana, and western Kentucky, as shown in Figure 1 (dotted lines). The estimated surface mineable coal resources in the basin amount to about 27 billion tons, and about 69 m. tons of coal is surface mined annually (Tab1e I).

Jan 1, 1981

By Thomas R. Mills

Under contract to the U. S. -Department of.-Interior, Office of Coal. Research, Hittman Associates recently completed a 16 month study of the environmental-factors associated with the siting, construction, and operation of large scale coal refineries. (1 2) The objective of this study was to identify the environmental effects and to define the magnitude of these effects and the approaches which can be used to mitigate adverse environmental consequences. In the study, the five major coal bearing regions of the country having reserves adequate to support a number of large scale coal refineries were considered. The regions considered were: Appalachian, Eastern Interior, Fort Union, Powder River, and Four Corners.

Jan 1, 1975

By J. Owens

The methodology of quarrying changed significantly in the Indiana Limestone industry in the sixty years between September 11, 1941, the date of the Pentagon groundbreaking ceremony and September 11, 2001 when the building was damaged by American Airlines Flight 77. So too, though to a lesser degree, did the machinery and methods used to fabricate the stone. The rededication ceremony on September 11, 2002 marked the end of the Phoenix Project, as the rebuilding effort was named. The story of this remarkable project illustrates what the American construction (and Indiana Limestone) industry can accomplish when working toward a common goal.

Jan 1, 2004

By J. R. Diehl, R. W. Lai, R. W. Hammack, S. U. M. Khan

Cyclic voltammetry (CV), flotation response, evolved-gas analysis (EGA), and X-ray photoelectron spectroscopy (XPS) were employed to evaluate the major differences in the surface property and surface reactivity of a selected coal pyrite and a mineral pyrite. Surface properties of pyrite were evaluated in terms of flotation response in the presence of both an anionic fluorosurfactant and sodium hydrosulfide. The charge transfer adsorption and oxidation potential of sodium hydrosulfide were evaluated using cyclic voltammetry. Drastic differences in the flotation response have been observed between the coal pyrite and the mineral pyrite. Significant differences in the cyclic voltammograms at pyrite surfaces of these two sources were also observed. Measurements by XPS and EGA were used to determine the oxidation products and the rate of oxidation of the coal-pyrite and the mineral-pyrite surfaces.

Jan 1, 1991