Search Documents

By G. A. Gunderson

Since our time is very limited, I would like to relate to you as best as I can a few important areas that I think may be helpful. 1.) The Real Difference between Dense Phase and Dilute Phase Pneumatic Conveying: Within the many variations of so called Dense Phase conveying, it is often difficult to determine to what degree a system is Dense Phase or if, in fact, it is a Dense Phase system at all. A system that appears and is generally known to be Dense Phase can under certain operating conditions perform as a Dilute Phase system. If, for instance, a high pressure system, which is generally a Dense Phase system, operates at 60 PSIG, say 4 atmospheres, utilizes enough air volume, the conveying velocity will easily exceed the normal design velocity of a typical Dilute Phase system. Now, on the other hand, a low pressure system which we will term a Dilute Phase system, operating at 15 PSIG; say 1 atmosphere, can convey a given product at well below the saltation velocity, like a Dense Phase system.

Jan 1, 1977

By William S. Pintz, William A. Vogely, Charles J. Johnson

This chapter on the role of minerals in developing economies is oriented toward economic policy issues. The discussion and analysis cut across the technical, economic, legal, and policy fields. The goal of this chapter is to pro- vide relevant background information important to individuals involved with the minerals sector in developing countries. Where possible, trends are shown to provide a basis for understanding the evolving role of minerals in developing economies. This chapter is divided into the following five sections: (1) characteristics of developing countries (which presents selected statistical comparisons); (2) government objectives in developing countries; (3) government policy formulation in developing countries; (4) determinants of future trends, and (5) a summary of the chapter's major points combined with the authors' view. CHARACTERISTICS OF DEVELOPING COUNTRIES There are 155 nations in the world categorized as "developing countries." In total these nations represent about one third of the value of the world's mineral production, three quarters of the world's population, and over half of the world's land surface area. The group of so-called developing countries is quite diverse and there are exceptions to almost any general observation about the group as a whole. Most definitions of the term "developing country" are based on levels of per capita income. However, if per capita income is the sole criterion used in categorization, then several oil-exporting countries would jump from the category of developing country to the category of developed country.a Obviously, this results in a poor fit with respect to other measures. In general, the majority of developing countries can be characterized by relatively low per capita income, high population growth rates, high levels of unemployment, low levels of education, short average life ex- pectancies, income distribution skewed toward the highest 20% of the population, and a large share of exports represented by primary commodities. b For the purposes of this chapter a slightly modified version of the widely used World Bank system of classification (shown in Table 1.2.1) is used. As summarized in Table 1.2.1, developing countries are divided into three main groups based on estimated gross national product (GNP) per capita. It should be noted that the high- income, oil-exporting countries have characteristics of both developing and industrialized countries; however they are included for most statistical comparisons within the group of developing countries. Of the 155 developing countries in the world, approximately half produce minerals other than common building materials, and only 32 account for more than five percent of world pro-

Jan 1, 1985

By J. P. Nairn, C. M. McCulloch

More and more underground mining is being conducted using the long wall method. Likewise, many new surface mines use area or mountaintop removal methods. These methods can have a significant impact on surface and ground water resources. The overall study of the effects on surface and ground water from mining is referred to as the probable hydrologic consequences (PHC) determination of mining and reclamation. Collection and interpretation of information concerning ground water and surface water quality and quantity, as well as detailed geologic analysis, is required to adequately define the impacts of mining. This paper discusses the present day requirements and methodology of preparing a PHC for a large mining operation in the eastern coalfields.

Jan 1, 1997

By C. W. Hoffman

A fairly recent development in the field of particle separation is now under investigation to determine its value to the mining industry. The method employed is probability sizing through a vibrating network of decreasing screen openings. While probability sizing as such is not new, the possibility of using it for coarse, highly abrasive ores at high tonnage rates has only recently appeared to merit practical consideration. The advantages to be gained by the use of probability sizing vs. conventional screening methods are: reduced space requirements for a high capacity unit, fewer moving parts, more versatile product sizing selection, reduced maintenance requirements and lower power consumption.

Jan 1, 1968

By T. N. Moore, E. M. De Souza

J. Dasher Regarding the March 1991 ME technical paper by De Souza and Moore: For more than a decade since my February 1981 article on how to use modern metric, which SME-AIME had decided to do, I have monthly pointed out metric errors to the editors. In part, I do this because there has been no action to allow editors to fix figures and tables or to allow them to require authors to do so. The latest resulting atrocity provokes this discussion of vibrating drill handle units being stated in decibels. Reply by T. Moore We have read the discussion of our paper by Mr. Dasher. Our reaction is one of surprise and incredulity. It would seem that Mr. Dasher takes exception to the use of the decibel scale to present vibration acceleration data, and the use of hertz as the unit for frequency. The basis for his objection to the decibel appears to be that it has no dimensions (which somehow invalidates its use), that it is "non-metric" and, finally, that it is parochial (of limited or narrow scope). His objection to the use of the term hertz is not stated, but we will assume that it stands condemned as "non-metric" and parochial. Obviously we disagree with Mr. Dasher's views and will now outline our reasons. Although the decibel scale originates from transmission line theory and telephone engineering, it is also at present widely used, not only in the fields of electronic engineering and acoustics, but also in the area of vibration. The original definition of the decibel (dB) was based on power ratios: dB = 10 log 10(W/W0) where Wo is a reference power. However, as the power measured across a given impedance is related to the square of the force acting upon this impedance, Z, a more commonly used definition is: [2 dB = 10 logF /Z) = 20 log F/F 10\ F0 2 /Z(0)] where F and F0 are the r.m.s. values of the forces. Now, if the measurements are related to one and the same impedance, the decibel notation in the form of 20log10(X/Xo) may be used as a convenient relative magnitude scale for a variety of quantities. Thus, X may, for instance, be an r.m.s. displacement, velocity or acceleration. It is only required that XD always be a reference quantity of the same type as X. That is, when X represents an acceleration, then X0 represents a reference acceleration. This is the formulation used in our paper. This was not an arbitrary choice on our behalf but reflects standard practice as specified in the International Standard ISO 5349-1986(E) Mechanical Vibration - Guidelines for the Measurement and the Assessment of Human Despite the metric prefix, the decibel is a parochial expression of (l) the logarithmic ratio of the loudness of a sound to what is normally audible or (2) the logarithmic ratio of two power signals in radio or electronics. A decibel is not a unit, much less an SI, unit and has nothing whatsoever to do with the acceleration of drill handles. Stating that m/s2 (acceleration) is decibels is without reason. Whoever reviewed this material should not have allowed publication of figures of dB and H.[ ] Exposure to Hand-Transmitted Vibration. This was clearly stated in the "measurement protocol" section of our paper. This quantity is then referred to as the acceleration level and is expressed in dB. We may have inadvertently caused some confusion when we simply used the term acceleration to refer to acceleration level on our diagrams. At the time, we felt the use of dB or m/s2 would make the context clear to the reader. For any confusion this decision may have engendered, we apologize. Since the decibel expresses the ratio of two like quantities, it certainly has no dimensions. It is, however, common practice to treat "decibel" as a unit as, for example, in the sentence, "The acceleration level measured at the operator's hand was 160 dB." The expression of measured quantities in dimensionless form is not inherently unacceptable. In fact, in many areas of engineering it is standard practice (consider the use of Reynolds Number, Nusselt Number, etc.). The fact that the decibel is a dimensionless quantity makes the question of whether it is a SI unit nonsensical. However, it is valid to insist that the dimensional quantities used to obtain the decibel values be expressed in SI units. A careful reading of our paper will make it clear that the measured acceleration was, in fact, expressed in units of m/s2 as was the reference acceleration (l x 10-6 m/S2). These are the accepted derived SI units for acceleration. See, for example, the standard ASTM E380-89a Standard Practice for Use of the International System of Units (SI) (The Modernized Metric System). Concerning Mr. Dasher's implication that hertz (Hz) is an unacceptable unit of measure for frequency, we would again refer him to the standard ASTM E380-89a. Here, he will find (section 2.4.2) that hertz is an accepted "special name" for the derived SI units-1. This is in keeping with numerous other international standards including ISO 5349-1986(E) to which we referred in our paper. In conclusion, we agree with Mr. Dasher on the desirability of expressing measurements in modern SI units. But we would remind him that the standards that define the use of these units, and the accepted means of presenting measured data, are in a continual state of refinement. It is, therefore, incumbent upon him to keep abreast of these changes if he wishes to constructively critique the work of others.[ ]

Jan 1, 1992

By J. C. Armbrust

The Morenci Open Pit Mine, located in south-eastern Arizona, is owned and operated by Phelps Dodge Morenci, Inc. The Mine has been predominantly a rail mine since its origin in 1937. However, beginning in early 1986, a program was initiated to phase out the rail mining operation and replace it with a more flexible and productive truck haulage scheme. This transformation from rail to truck haulage will be accomplished when the current in-pit crushing and conveying project is completed in late 1988.

Jan 1, 1988

By Zvonimir Jam?ek

In Rudarski Institut Ljubljana (RIL), i.e. Ljubljana Mining Institute, we have developed CADRIL, a smaller CAD package which purpose is to overcome the difficulties by introducing Computer Aided Design in our mines. Program CADRIL is a graphics shell for several computer applications in mining. With the basic version of CADRIL all 2D working maps for daily use can be produced. Inserting different program blocks into CADRIL we get versions MAPRIL, TAHRIL, SECRIL and so on. The main purpose of all versions is graphics design. The main and most innovative feature of CADRIL is the screen four-word command menu. Not having pull-down or tablet menus is the speciality of this program. CADRIL contains 500 achievable commands. Each of them can be composed by choosing two to four expressions stored and shown in a specific four- column menu, sorted as objects functions, parameters and modes. Thus all commands are immediately accessible. As a result of its plainness and adaptability to the present working methods of mining engineers, CADRIL quickly attained a good reputation in our mines.

Jan 1, 1992

By Bruce C. Schepens

The Balsam Meadow Hydroelectric Project is currently under construction in central California. TMCI Construction, Inc. was subcontracted to perform the shaft enlargement and lining required for the elevator, surge and power shafts. Involved in the initial work was slashing the elevator and surge shaft into a previously excavated borehole. The elevator shaft then required a reinforced concrete lining and structural steel installation. Throughout the course of construction, numerous design changes occurred, necessitating a lining in both the power and surge shafts. These changes caused TMCI to design two underground hoisting systems to install these additional linings. An analysis of the construction methods used is now given. Introduction The Balsam Meadow Project consists of an underground hydroelectric powerhouse designed to provide additional capacity and energy to the Southern California Edison system during critical peak demand periods, and has the capability for pumped storage operation. The project is located in the Sierra Nevada Mountains about 55 miles northeast of Fresno. The project will divert water presently flowing from Huntington Lake to Shaver Lake to power a single 200 megawatt turbine generator. The approach used to the shaft slashing was governed partially by the strict CAL-OSHA requirements, which became more stringent after the recent Helms' Creek accident. A scaled down sinking plant was used to minimize economic risk and to simplify the excavation and lining scheme.

Jan 1, 1987

By Frank X. Bellini, Marc Saidman, Allen J. Hulshizer, Anthony J. Stewart

The cooling water system for the Seabrook Nuclear Station involves 10.25 Km (33,623 ft.) of 6.7 m (22 ft.) OD hard rock tunnels, over one third of which is under and terminating over 1.6 Km (a mile) out in the Atlantic Ocean. The major excavation is accomplished by two TBM's concurrently driving the intake and discharge tunnels which by mid-January, 1981, completed 92% of the excavation. This paper presents the case history of the excavation work and describes a computer program developed to evaluate major activities of TBM excavation on a shift-by-shift basis. Details and summaries of the production efforts are computer plotted in different forms to facilitate the evaluation of production performance, trouble spots and trends.

Jan 1, 1981

By Trevor A. Moss

Installation of equipment and structures at mines often requires mine planners to evaluate unique loading and operating conditions. Consideration of these unusual features is required throughout design and construction and into operation. Most planners understand the necessity of employing sound civil, structural and mechanical engineering techniques to design these structures and equipment. However, the influence of geotechnical factors on the overall progress of construction and operation is less appreciated. Mine operators routinely perform exploratory drilling to define ore deposits. These exploration activities can be extensive and often include provisions for assessment of subsurface conditions as they relate to the mining operation - requirements for ground support. All of these factors are important to the economics of the mine and are well justified. Surface facilities are provided to access and service the mine, and they play an important role in the successful development and operation of a project. Headframes, hoist foundations and shaft collars, in particular, are examples of unique installations encountered at underground mine sites. The design and above-surface behavior of these facilities can be analyzed with the usual fundamental engineering practices employed throughout the engineering professions. However, near surface exploration for the purposes of assessing soil and rock conditions for foundations is often given a reduced priority and less consideration. This article provides an outline of the benefits and importance of performing such exploration. References here relate particularly to shaft headframes, hoists and shaft collars. But the issues raised apply equally to other installations of a similar nature, including milling equipment.

Jan 1, 1992

By L. Adler

In spite of distractions from glam-our areas (ground control, computers, etc.), excavating and bulk handling in mining remains paramount but is now undergoing dramatic advances. The massive intervention of mining and civil engineers as "engineer-users" into the tight, exclusive, and specialized bond between the equipment operator ("operator-users") and the manufacturer (mechanical engineers "and sales "reps") has now occurred. Three developments have accelerated this: 1) larger, more costly, complex, specialized, and innovative equipment; 2) a more profound understanding of the equipment, operations, and working conditions (encumbered space); and 3) a concurrent thrust into "high-tech," (automatic and remote controls, sensors, automation, artificial intelligence, and even robotics) and human factors (workload intensity, work-station design). This has produced a well-defined professional discipline, including construction and even military engineering. The mine plant, and to a lesser extent, the mine face, is now being monitored. Equipment conferences, journals, and centers at universities and agencies have multi-plied. The discipline's impact on future mining now becomes more apparent.

Jan 1, 1988

By Dan Swidrak, Bill Zietlow

Halfway through a 17,770-ft long stormwater tunnel, an 11-ft diameter TBM encountered a karst void below the Mississippi River in Missouri, resulting in significant inflow. It was decided that the TBM could not safely advance without external intervention. Low-mobility grout was pumped from the surface. A rescue shaft was constructed and a conventional tunnel with spiling support was mined back to the machine. The TBM was removed and a 14-ft diameter TBM equipped with probing drills was relaunched. Probing from the new TBM encountered one additional karst feature but the machine advanced after grouting and successfully completed the tunnel.

Jun 23, 2024

By Don C. White

Santa Rosa is a mid-Tertiary, volcanic-hosted, gold-silver deposit. Current proven and probable reserves are 8.9 Mt (9.8 million st) grading 1.5 g/t (0.044 oz/ st) gold, minable by open pit and amenable to heap leaching. It is the product of hydrothermal mineralization along an arcuate segment of a caldera collapse ring fault in a probable maar volcanic setting. This segment was later broken by radial faults. Gold at Santa Rosa occurs principally as electrum, finely disseminated through intermediate tuffs, and associated with pyrite. The nearby Alto de la Mina deposit displays stockwork silica-pyrite-gold in a tectonically and hydrothermally shattered andesite flow. Miocene epithermal mineralization was accompanied by central silicification and pyritization and more distal argillization. An andesite flow cap rock at Santa Rosa played a pivotal role as an upward permeability barrier. Highest gold grades and most intense alteration occur closest to the ring faults and immediately beneath the andesite flow. Supergene alteration effects on the gold distribution are minimal.

Jan 1, 1995

By Lane White

In conjunction with its 1993 Annual Meeting, held Feb. 15-18 in Reno, NV, SME sponsored a symposium, "Conveyor Belt Engineering for the Coal and Mineral Mining Industries." Eighteen papers were presented, grouped into four sessions: Low Tension Drives, High Tension Drives. Novel Techniques and Specifications. Three of the papers have been republished in this issue of MINING ENGINEERING. Brief summaries of the other 15 papers are presented here. (The 193-page symposium Proceedings, edited by Mike Evans of Consol, includes all of these 18 papers and is available from SME. For the convience of interested readers, an order form is included at the end of this Proceedings summary.)

Jan 1, 1993

By J. Bigu

Use has been made of several theoretical models to predict radiation levels in underground uranium mines. The models used are the Evans model, the Thomas-Epps mine model, the isolated mine model, the mine tunnel with no air flow and the mine tunnel with air flow (Beckman and Holub). Calculations based on the above models have been extended to include thoron gas and its progeny, a common occurrence in some Canadian uranium mines. Theoretical predictions include radon and thoron progenies WLs and concentrations, and some ratios of great practical interest. The main differences between the models are pointed out and comparison is made with experimental data gathered during the last three years in several Canadian underground uranium mines.

Jan 1, 1981

By R. S. Shepard

A quick glance at a-portion of the title of this discussion -'Rolling With The Punch" may immediately lead you to assume that I am about to expound on the so-called manly art of self-defense. So that you will not have been misled entirely we will devote our considerations to a far more important art and if I may, I should like to begin by quoting Vincent Van Gogh. According to a literal translation the artist in describing one of his famous paintings said "these peasants are eating their potatoes with those very hands that dug them from the earth' and put them in the dish". Vincent Van Gogh may not have realized at that time, that he could likewise have been describing what is probably one of the oldest of all arts - the art of Material Handling - an art that man with the aid of science has tried to improve since the beginning of time.

Jan 1, 1963

By L. A. Panek

A new pillar strength formula is presented. It incorporates a function [IF] of size and shape that takes into account the size-shape interaction effect as well as the enhanced strength exhibited by wide pillars. Existing pillar formulas, lacking these capabilities, are not suitable for extrapolating small-specimen test results to mine-pillar sizes and shapes. Interpreting compressive strength test results as function of [Y] reveals wide-pillar behavior in much old test data. Model relationships are discussed, along with their scaling implications.

Jan 1, 1995

By James P. Dorian, James M. Otto

The value of exported nonenergy minerals from the less-developed countries has increased substantially between 1970 and 1985, but their market share relative to world exports has remained stagnant. Of the top twenty minerals exporters, only four are developing countries. Production capacity in the developing countries is shown to be less sensitive to demand downturns than capacity in the developed countries. Two approaches to the management of cyclical minerals demand are given using examples from India and Papua New Guinea. The authors conclude that pro¬tective policies implemented by developing nations have, barring a few exceptions, relatively little impact on the chronic nonfuel minerals oversupply problem.

Jan 1, 1989

By R. S. Conti, L. L. Chasko

To deal with an unexpected event such as fire, prevention and preparedness are important elements in an underground mine's strategic plan. The purpose is to prevent afire before it initiates and to be prepared to deal with it when it does occur. This paper highlights a technology that may be used by the mining workforce to minimize such occurrences. It discusses thermal imaging cameras and their many applications to detect equipment failures or hot spots before they develop into afire. It also evaluates the feasibility of using thermal imaging cameras for emergency responders to assist them during exploration, rescue and fire fighting efforts. These thermal imaging systems allow rescue personnel to see in darkness and through dense smoke, thus making it easier to locate heated areas and missing or trapped personnel.

Jan 1, 2003

By A. Goulsbra, S. Gregory, P. Gelfil, V. Martins, R. Dunne

As a general rule for gold treatment the presence of reasonable amounts of 'coarse' free gold will dictate the use of a gravity circuit. The actual particle size of gold that constitutes the por­tion of' coarse' free gold can vary widely. The larger its size the more troublesome it is, mainly because of the tendency for this gold to quickly settle out from slurries in regions of relatively low velocities. There are a multitude of places where 'coarse' gold can find a resting place, namely, in chutes, between and behind lines, in pump hoppers and in pumps themselves. Fortunately, the problems associated with recovering very 'coarse' free gold, say greater than Imm, is rare on most gold mines that have grinding and cyanide leaching circuits. For these operations it is common practice to have a gravity circuit situated within the milling circuit to recover 'coarse' free gold. Should the 'coarse' free gold constitute 15% to 20% of the total gold in a deposit then its recovery by gravity separation is seri­ously considered. As a gold mine 'matures' the availability of soft oxide ore decreases and the likelihood that harder ore having sulphide gold association increases. To maintain gold production rates in this situation either the gold grade of the treated ore must increase or more ore needs to be treated. In the latter case this is achieved by installing more grinding capacity, an expensive option, or coarsing the grind, with the downside of loss in gold recovery. In general the less expensive capital options is fol­lowed. There is, however, some upside to improve recovery when reasonable quantities of sulphide containing gold are pre­sented that can be recovered by flotation or gravity separation. Concentrates produced from these unit operations can be finely ground and reintroduced to the cyanide leach circuit to improve gold recovery. This scenario is a much less costly option than one where all the ore is ground finer. In this paper the experiences of recovering gravity gold from the Telfer Gold Mine, and gold associated pyrite from the New Celebration Mine will be discussed.

Jan 1, 1996