Search Documents

By Patrick R. Taylor

This paper presents a fundamental study of the thermodynamic and kinetic effects of copper and iron on gold-cyanide leaching. It quantifies the solubilities of the impurities, complex formation, and kinetic effects. The necessity of solution recycle, to meet environmental standards, requires that fundamental information be generated to characterize behavior and allow the identification of treatment methods. Mathematical descriptions of both solubilities and kinetics will be presented

Jan 1, 1983

By Daniel J. Brunner

The U. S. Department of Energy (D.O.E.) requires that the prospective nuclear waste repository in Basalt at Hanford, Washington, comply with State of California mine and tunnel safety orders. These regulations require that all main fans be installed in such a manner as to permit prompt reversal of airflow. This paper evaluates the requirement of air reversal and the appropriateness of imposing such regulations on the proposed nuclear waste repository in Basalt.

Jan 1, 1988

By Harold L. Kike

Until recently sulphur uses were so broadly based that economists used sulphur consumption to measure industrial activity. However, sulphur use patterns are changing and the manufacture of phosphate fertilizers presently accounts for approximately 65% of the world's sulphur consumption compared with only 25% in 1960. This has encouraged the development of new agricultural and industrial uses for sulphur. Major emphasis has been placed on its use as a fertilizer and in the manufacture of paving materials, specialty concretes and coatings. Some of these uses could have a significant impact on future sulphur usage.

Jan 1, 1986

By E. V. Kuzmin

The rock properties improvement means the exchange of natural properties: increase of stability, strain and compress tension, reduction of gas-liquid filtering property, increase Jung- module, other mechanical and physical parameters of rocks by injection the hardening materials, such as polymeric pitches, micro-or geocements by special technology under high pressure, to fill cracks. Flow of liquid materials between the rock units and hardening under high pressure create full redistribution of rock pressure in rock massif. There are many reasons to use this technology in underground mining, tunnelling, creation barrier technology in raioactive, chemical and other danger material site etc.

Jan 1, 1996

By C. G. Cunningham

The Marysvale volcanic field of west-central Utah contains large areas of argillically altered rocks (fig. 1) that, in turn, enclose smaller areas of fine-grained, medium-grade, replacement alunite deposits and coarsely crystalline, high-grade vein-type alunite deposits. The largest replacement alunite deposits are [ ] located peripheral to a 23-m.y.-old monzonite stock called the Central Intrusive (fig. 1). The deposits formed in near-surface, highly oxidizing environments at the tops of hydrothermal plumes that were spaced irregularly around the stock. The deposits are horizontally zoned from alunitic cores through kaolinitic to propylitic envelopes. Vertically, characteristic alteration minerals progress from a pyrite-propylitic alteration assemblage at the base, upward through alunitic, jarositic, and hematitic assemblages to a flooded silica cap as shown on figure 2. The silica caps are cut by hydrothermal explosion breccias. d34Sso4 values of + 11.5 to + 15.4 permil indicate that sulfur in the hydrothermal plume was derived from underlying Mesozoic evaporites. The sharp upward transition from pyrite- propylite to alunite probably marks the paleowater table, and the top of the flooded silica cap represents the paleoground surface. Basin-Range extensional tectonism began shortly after alteration, and buried the replacement alunite deposits in basins beneath sediments eroded from uplands. The deposits were only recently exhumed.

Jan 1, 2013

By P. R. A. Andrews

Areas of bubble contact were delineated for topaz and tourmaline in the presence of chloride, fluoride, sulfate, phosphate, oxalate, and citrate ions using dodecylamine hydrochloride collector. The limits of pH and the minimum collector concentration were established using the bubble pick-up technique. Bubble contact did not occur below the p.z.c. (point of zero charge), estimated to be 5.6 for topaz and 6.6 for tourmaline, in the presence of chloride ion. Flotation below the p.z.c. was, however, extended by citrate, oxalate, phosphate, sulfate, and fluoride ions. Oxalate, citrate, and fluoride ions displayed the greatest pH range of activation, followed by phosphate and sulfate ions. Chloride ion acted as an indifferent electrolyte. Topaz was selectively activated with respect to tourmaline by fluoride and phosphate ions. Topaz was activated by fluoride ion between pH 2.4 and 5.6. Tourmaline flotation in this pH range was virtually insignificant. Topaz was activated by phosphate ion between pH 4.9 and 7.4. Tourmaline flotation in this pH range was only partial. Activation appeared to be strongest when anionic protonated species were in maximum concentration. Strong activation also corresponded to very stable metal ion species thought to be formed on the surface of each mineral.

Jan 1, 1991

By Joseph R. Hatch

During the past ten years detailed elemental analyses of approximately 8,000 well-documented samples of coils in the United States (including Alaska) have been produced by the U.S. Geological Survey and the various State geological surveys. Examples of data listings include Swanson and others (1976) Gluskoter and others (1977) Hatch, Affolter, and Davis (1979), and Wedge and Hatch (1980). These analyses serve as a basis for evaluating elemental abundances in coals from the various coal province, regions, and fields. When combined with additional geological and geochemical data, some of these analyses give insight into when certain elements were introduced into coals, and which physical and geochemical parameters are most important in determining coal elemental composition.

Jan 1, 1982

By Hans von Michaelis

It is appropriate that this opening session of HAZPAC '91 and Randol Gold Forum CAIRNS '91 should address the question of what the two industries can learn from each other. The panel is made up of members with experience in both industry. Several are experts on managing both hazardous waste and the mine/mineral processing environment. There is a marked difference in the regulatory needs with respect to treating and disposing of mining and mineral processing wastes, and "hazardous" or industrial waste materials. The topic of this paper is on the things that the two industries have in common: Many of the processes and technologies that are being used or are currently being developed for treatment of hazardous waste are the same or similar to the processes that have been used for decades or k,nger in the mineral processing industry. Hazardous waste treatment and remediation of contaminated solid and/or groundwater is a relatively new industry. Many of the practitioners in this new industry are relatively inexperienced in most of the "new" technologies that are being applied or developed.

Jan 1, 1991

Mining employment, gross output, local economic contributions and productivity are typical economic indicators. However, these economic indicators play a much bigger role in the overall capacity of the industry to be heard in decision-making on a national scale. Total mining employment in the USA has decreased significantly in the last 20 years. Gross output from most of the mining sectors has also declined, except in the case of construction aggregate. However, significant gains have been made in productivity. This paper explores these statistics and comments on their overall impact on academic institutions and political decision-making.

Jan 1, 2003

The paper describes the procedure of data inquiry on the structure of mineral production in Austria and selected results. Goal of the endeavor was to gain more tangible insights into the mining industry as a basis for regulation balancing economical, ecological and social aspects.

Jan 1, 2006

By Dennis J. Appelhans

Lac Minerals Bullfrog conducted research and testwork to find an environmentally acceptable alternative to lead for fire assaying. The result of this work was the substitution of bismuth for lead in all fire assaying performed at the Bullfrog Mine. The environmental and economic ramifications of this discovery are highlighted.

Jan 1, 1993

By Steven J. Schatzel

A study was made of frictional ignitions in the underground coal mining industry from 1980 to 1992. The population of frictional ignitions was correlated to a variety of potential contributing factors including the mined coalbed, geographic location, mine production, methane gas emissions, and the type of mining equipment in use. The number of frictional ignitions reported in 1991 and 1992 surpassed the annual totals in all previous years included in the study. Most frictional ignitions occur during cutting operations at a coal face by a continuous miner. The average coal production of mines experiencing frictional ignitions is greater than the average of all underground coal mines throughout the survey period. Methane drainage may have produced a drop in the ratio of gas emissions to coal production (E/P) in mines experiencing frictional ignitions.

Jan 1, 1995

By Dan Swidrak, Bill Zietlow

Halfway through a 17,770-ft long stormwater tunnel, an 11-ft diameter TBM encountered a karst void below the Mississippi River in Missouri, resulting in significant inflow. It was decided that the TBM could not safely advance without external intervention. Low-mobility grout was pumped from the surface. A rescue shaft was constructed and a conventional tunnel with spiling support was mined back to the machine. The TBM was removed and a 14-ft diameter TBM equipped with probing drills was relaunched. Probing from the new TBM encountered one additional karst feature but the machine advanced after grouting and successfully completed the tunnel.

Jun 23, 2024

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

Jan 1, 1986

By Nobuharu Isago, Atsushi Kusaka, Kosuke Kawata

"Strong earthquakes occur frequently in Japan, and some rock tunnels have sustained severe damages on their permanent lining. Many road tunnels, which were constructed by conventional steel arch support and timber lagging method, exist in Japan and they need risk mitigation measures against earthquakes as per our empirical knowledge. Many reinforcing measures for deformed tunnels that may be effective against earthquakes are developed; however, behaviors during earthquakes are not fully understood.In this study, static loading tests and numerical analysis, which simulate a loading condition during earthquakes, were carried out to clarify the effect of the countermeasures. The Load-bearing capacity is estimated for the tunnel structures facilitated by the installment of an inverted arch; however, a joint between inverted arch and sidewall become structural weakness. Rock bolts and carbon fiber sheets have a potential able to mitigate the risks of collapse of the lining by the forces from an earthquake.INTRODUCTIONA number of rock tunnels with no apparent unfavorable ground conditions suffered severe damage, including the collapse of their permanent lining, in large seismic events such as the Chuetsu Earthquake in 2004 (e.g., Mashimo 2005). Since these tunnels were considered to exhibit the required structural strength to survive earthquakes, studies are being carried out to clarify the mechanical behavior of tunnels during earthquakes and their damage mechanism (e.g., Kusaka et al. 2009); however, the aseismic design methodology for mountain tunnels has not yet been established.In many cases of earthquake-damaged tunnels, some defects already existed, such as improper construction and deterioration of lining concrete. Although countermeasures are usually implemented against such problems, their earthquake-resistant effect was not fully understood.In this study, static loading tests and numerical analyses to reproduce these tests were carried out assuming that a rock tunnel was affected by the earthquake to clarify the mechanism of the lining damage and the effect of the countermeasures."

Jan 1, 2016

By Carol A. Hill

Native sulfur occurs with barite, celestite, and bioepigenetic calcite in the Culberson, Pokorny , and Leonard Minerals deposits, Delaware basin. The sulfur in these deposits, in "castile" masses, and in deposits of the Fort S tockton district have 6 34s values between +9 and -15. Native sulfur in the caves of the Guadalupe Mountains is somewhat lighter [(634s = -15 to -25)]. Barite in the Culberson, Leonard Minerals, and Comanche Creek sulfur deposits have 63% values of +35 to +73; celestite in the Culberson and Leonard Minerals occurrences have values of +38 and +36, respectively, and 87Sr/86Sr values of 0.707808 and 0.708138, respectively. Barite associated with sulfide, deposits, Guadalupe Mountains, have [634s] values of +41 to +62. Barite at Seven aeart Gap, Apache Mountains, is somewhat less enriched in heavy sulfur [(634s = +14 to +37)].

Jan 1, 1992

By J. J. Crowhurst

The modem open pit-heap leach operation by Pegasus Gold Ltd. at Zortman and Landusky in Phillips County, Montana, is a new chapter in the mining of gold in these districts. The discovery of bulk tonnage ore bodies and their development and ultimate production was based on a long history of mining and exploration in that part of Montana. Gold was originally discovered in the Little Rocky Mountains as placer deposits by Pike Landusky and Lou Myers. This discovery in the 1880s was not significant, but Pike Landusky continued prospecting for lode deposits, and he eventually located the Gold Bug and Little Ben, two of the larger Au-Ag producers in the district. Eventually two camps, Landusky and Zortman, grew in the LittleRocky Mountains. By the time Landusky was killed in 1894 by Kid Curry, the district was still a discontinuous small producer. Steady production commenced in 1907 with the organization of the August Gold Mining Co. Eventually high grade ores on specific veins were exhausted by selective underground mining and the district was idle by May 1942. After World War II in the early 1950s. E.A. Scholz tried to continue selective underground mining, but he realized the stockworks surrounding the larger veins constituted bulk tonnage targets. Ultimately in the 1976- 1979 period he organized two exploration efforts, one each for the Landusky and Zortman areas, and brought these into production as the Argo and Pegasus gold mines. By the time of his death, Apr. 8, 1980, both operations were producing gold. Later the two companies were merged as Pegasus Gold Ltd. Upon the death of Scholz, V.F. Hollister continued as the geological consultant, Ed Roper was engaged as general manager, and J. J. Crowhurst was given the responsibility of executive vice president. The discovery of open pittable ores and the application of heap leach technology was important in the development of mining. Both contributed to the low cost operation that continues to this day. The attached article by L.M. Rogers, then chief geologist, and M.S. Enders, his assistant, describes the geology of the deposit. It was presented at the Northwest Mining Association meeting in 1982.

Jan 1, 1990

By I. Pordea

The materials used for the construction of buildings contain natural radionuclides of the U238 and Th232 series and are ? 50% due to land radioactivity. Another component of natural radioactivity is K40, with ? 40%. The presence of these radiopollutants in the final products (i.e. bricks, concrete) due to body irradiation is by two pathways: external irradiation and internal irradiation. External irradiation is due to gamma radiations emitted by Pb214 (RaB) + Bi214 (RaC) from the U238 series, by Ra228 (Mezothoriu I) + Ac228 (Mezothoriu II) + Tl208 (ThC??) from the Th232 series and by the K40 radionuclide. Internal irradiation is due to inhalation of radon (Rn222) and Rn220 (Tn) plus short life descendents (Po, Pb, Bi), radionuclides which are present in concrete. A fraction from radon present in concrete enters into a house leading to internal irradiation by inhalation. In Romania, the maximum concentration of radon allowed for new buildings is 200 Bq/m3.

Jan 1, 2008

By Erwin A. Morlan

Present methods of boring large hole mine openings are briefly reviewed. Factors that influence the design and choice of down-the-hole equipment for rotary drilling large holes are discussed. With formation drillability taken as a starting point, graphs and charts are given as an aid in the selection of bit load, circulation system, flow rate, drill stem, cutter design and rotary speed.

Jan 1, 1961

By S. Kelebek, G. W. Smith

Four samples of galena, each prepared differently, dry ground chalcopvrite and real gar have shown various quantities of liberated sulfur corresponding up to nine equivalent monolavers on their surfaces as determined by the solvent extraction/UV analysis of sulfur using ethanol. The pretreatment of a dry ground galena sample with acidified ammonium chloride or neutral, saturated sodium chloride solutions rendered the mineral readily floatable. The collectorless floatabilities of galena pretreated with the former solution and of drv ground chalcopvrite have been evaluated in reference to the natural floatability of sulfur using the critical surface tension of floatability approach with aqueous methanol solutions. It is shown that the amount of sulfur- on these samples can be correlated with their flotation rate, which was found to he first order within the critical surface tension range. The larger the concentration of surface sulfur, the faster the sulfide mineral floats, thus, the greater its flotation rate constant.

Jan 1, 1990