Search Documents

By R. L. Grayson, R. C. Althouse, M. J. Klishis

The health and safety of employees, efficiency of the operating system, and production are paramount goals in underground coal mining. The section foreman assumes responsibility for making his part of the total system function to meet these goals. However, section foremen often have not been prepared to assume the full range of their responsibilities upon becoming a supervisor. This paper addresses the full range of section foreman responsibilities and concomitant authority. Management principles that must be mastered by him are presented, and performance expectations as well as criteria for their evaluation are examined. The benefits realized from effective foreman training are discussed.

Jan 1, 1987

By I. Longson

As a longwall coalface advances a caved goaf or waste region is left behind. Air flow takes place through this permeable goaf due to the pressure differentials existing across it and en route this leakage air picks up both heat and moisture. A marked deterioration in climatic conditions occurs in the face area at all points downstream of where this leakage air rejoins the main air-stream. This goaf heat source can make a very significant contribution, typically 30-40% to the rate of total heat pickup on an advancing UK longwall coalface with a VST of 40°C and hence on the climatic conditions that prevail at the return end and in the return gate of the face. The magnitude of the rate of heat collection from the goaf depends on a number of factors but it has been established that it is particularly influenced by the prevailing virgin rock temperature and the total flow rate of the leakage air. This paper proposes a model for the goaf based on a packed bed analogy and other assumptions required in order to evaluate the rate of heat pickup are identified. The outlet condition of the leakage air predicted by the model have been shown to correlate with underground measurements taken for a range of different production patterns with the face cutter at various locations on the face. The sensitivity of these predictions to variations in the input data has been tested and is commented on. At this stage of the development the capabilities and predictive limitations of the model are discussed. Further areas of investigation are suggested in order to improve the predictive ability and to extend the versatility of the model.

Jan 1, 1989

By Randal J. Barnes

In, any open pit mine the ability to make accurate production estimations for the shovel-truck system is an important asset. This is true in an operating mine wishing to estimate production under a set of system modifications (i.e. more trucks, fewer loaders, change in roads, etc.), as well as in the pre- mining planning stages of a property. Many different methods have been proposed for solving this problem; some of the methods rely heavily on "rules of thumb" while others are highly mathematical and require access to a high speed digital computer. Analysis of shovel-truck systems with the use of simulation models is a widely accepted technique within the industry. Through the use of such models it is possible to account for much of the inherent variability of the system and thus produce meaningful results. However, simulation studies are expensive. Formulation and setup of the actual simulation model requires a significant commitment of time and energy. In addition, the cost of the necessary computer runs is often of considerable magnitude.

Jan 1, 1979

By F. Montgomery Lyon

Pyritic sulfur in coal occurs as discrete mineral particles, and its liberation and physical rejection is the primary target for coal desulfurization. An acceptable solution to the pyrite removal problem from fine coal is not found in the standard methods of coal cleaning such as jigging, heavy-medium separation, tabling, and hydro-cycloning. Although fine coal is an ideal size for froth flotation, this method, as currently practiced is also unsuitable as the fine pyrite usually floats with the coal. One possible solution to this problem may be the froth flotation of pyrite from coal. This reverse flotation scheme would have the major advantage of removing both free pyrite and locked pyrite-coal combinations. With this possibility in mind, we have, as a first step, compared the flotation and adsorption. characteristics of an ore-pyrite and coal-pyrite with potassium-ethyl-xanthate as a collector 1 Related Research. The action of ethyl-xanthate on coal has been studied 2 by Horsley. He measured the contact angles of coal in distilled water and in the presence of purified ethyl-xanthate. The results indicated that the xanthate was not adsorbed by the coal. Additional contact angle data were obtained to determine the effects of cupric, ferric, and ferrous salts on the system. Then either the ferric or cupric salts were in, solution with the xanthate, there was an increase in the natural contact angles of the coal. This indicated that these heavy metal ions activated the flotation of the coal with xanthate. However, ferrous iron did not act as an activator. Horsley stated that the most attractive explanation was that the xanthate is oxidized to dixanthogen in the presence of the ferric and cupric ions.

Jan 1, 1971

By Po-Wei Tun, Kuen-Yuh Wu, Tso-Min Shih, Hsi-Chiang Fang

The purpose of this study is to investgate the coal dust explosion characteristics and to search for the prevention methods of the coal dust explosion as well as the propagation of the explosion flame of the middle-bearing coal formation in Taiwan by an open type coal dust explosion apparatus in laboratory. The coal samples were taken from the typical middle-bearing formations of the Sam-Ming,Tai-Ho and Lee-Fong coal mines The rock dusts, the free water mixture with coal dust samples and the interval clean out the coal dust in the testing chambers were applied for preventing the coal dust explosion and the propagation of the explosion flame.

Jan 1, 1993

By Fred W. Shultz

In the past we have been somewhat harrassed by the terms "'quality control" and "process control". This is especially true where the industry is dependent upon the chemical analysis of their product which in turn informs them how, well they have been controlling the process. The information which they have received, in most cases, is of an historical nature rather than of current value. The word "control" is to have more significance in future operations. This is particularly true in the metals industry. As the industry continues to process lower grade ores, and processing costs continue to rise, they must obtain more information faster to exercise "control" to its fullest extent.

Jan 1, 1963

By K. A. Natarajan

The relative significance of corrosive and erosive wear in magnetic taconite grinding is examined. The influence of different types of aeration, namely, nitrogen, air and oxygen on ball war was established for mild steel and high carbon low alloy steel balls. Ball wear data from dry and wet grinding tests are compared with those obtained in the presence of an organic solvent that does not promote electrochemical corrosion. 'Marked ball grinding, tests along with electrochemical measurements involving ball material and magnetite electrodes indicate that contribution from oxygen towards wear (corrosive wear) is relatively small and abrasive wear appears to be significant. Rheological properties of the slurry-appear to have an important bearing on the abrasive wear of grinding balls.

Jan 1, 1983

By K. Nielsen

The paper uses three examples to illustrate the challenges that the minerals industry is facing with regard to our image and the public?s perception of us. The paper then discusses communication with stakeholders as opposed to lecturing to the public and the authorities, and states that the industry needs to work more directly towards politicians and regulators as target groups. The conclusion is that we still have a way to go before the industry is doing enough to bring our message to the right people, but we are improving.

Jan 1, 2007

By Ki Chun

Optimizing ore processing requires a thorough understanding of not only the process itself but the economic constraints which influence business decisions. No single modeling technique is able to model all the different processes running in today's mines. The solution then is to use a number of different model­ing techniques, each competing with the others to best correlate the data. Among these modeling techniques are: Neural Networks, Genetic Algorithms, Fuzzy Logic, Crisp Logic, Statistics, First Principal Models, and System Identification models. Once a model has captured the behavior of the process, a numerical optimization determines the optimal operating point and set point parameters. A single step is then taken in the direc­tion of the optimal location by changing all the process parame­ters to the setting recommended by the optimization system. As the process begins to re-stabilize, the models are updated, the new optimal determined and another step is taken in the direction of the optimum. Through the use of multiple competing models integrated into a numerical optimization the process can achieve the optimal running condition even if the ambient conditions fluctuate dynamically.

Jan 1, 1998

By Dan Nilsson

Open pit mining is the strong sector of the American mining industry. In the middle of the 60's. 17-18% of the ore in metal mines was mined with underground methods. From the middle of the 60's to 1980 the production in open pit metallic mines increased from about 400 to close to 600 million short tons while at the same time the underground mine production decreased a little, from about 90 to about 80 million tons. Less than 15% of the ore prodction now come from underground mines. Large amounts of waste rock were also handled in the open pits. In the middle of the 60's about 600 milion tons were handled, in 1980 1,200 million tons were moved. This means that the average stripping ratio increased from about 1.5 to over 2.0 tons of waste rock per ton of ore, figure 1.

Jan 1, 1983

By P. Somasundaran, Brij M. Moudgil

All the major interfacial technologies encountered in mineral processing involve adsorption of surfactants and/or polymers. With the need for processing low grade complex ores it is imperative that conventional techniques such as flotation and flocculation be extended to meet the challenge of treatment of fines. Addition of surfactants or polymers is indeed not limited to the solid-solid separations but extends to particle size reduction in the form of grinding aids and dewatering operations as well. Although progress has been made in recent years to understand the science involved in various interfacial processes, more challenges and opportunities exist today than ever before in processing of the low grade finely disseminated ores. A brief review of the recent advances and the challenges in mineral processing, especially, those related to the interfacial technologies is presented.

Jan 1, 1989

By Ralph J. Holmes

INTRODUCTION Although sampling techniques used by the mineral industry continue to improve, sampling is still an area which is often neglected. Frequently, sampling and sample preparation requirements are left to personnel who do not fully appreciate the significance and importance of sampling. Consequently, plant evaluations are often based on seriously biased samples, leading to mass balance problems and incorrect assessments of plant performance. The basic rule for correct sampling is that each particle of ore or concentrate must have an equal probability of being collected and becoming part of the final sample for analysis. If this is not the case, bias is easily introduced and the sample is not representative. For example, when ore is travelling on a conveyor belt, the lumps may come to the surface. Consequently, a grab sample taken from the top layers only will contain a greater proportion of lumps, i.e., the sample is biased. There seems little point in making major investments in precise analytical equipment, if the sample provided to the analytical laboratory is not representative in the first place. This paper describes the sources of plant sampling errors, reviews the methods of estimating their variance, presents some worked examples, and provides some practical advice for reducing sampling errors and their variance. SAMPLING BASICS It is generally accepted that the discharge point of an ore or concentrate stream is the most suitable sampling location. The stream can be intersected at regular intervals, and representative samples, referred to as increments, can be obtained by taking a complete cross-section of the ore stream. On the other hand, sampling devices that take part of the stream on an intermittent or continuous basis, e.g., a bleed from a pipe, may introduce serious bias, and should be avoided at all cost. Increments may be taken at completely random times or tonnages during the sampling operation, in which case it is called "random sampling". However, as shown below, random sampling results in the largest sampling variance, so it is preferable to divide the ore or concentrate stream up into strata of equal time or mass and take one increment from each stratum. This operation is called stratified sampling and may be either systematic sampling, in which increments are taken at the same point in each stratum, or stratified random sampling in which the increments are taken at random within each stratum. Systematic sampling results in the smallest sampling variance, provided periodic variations in quality or quantity are not present which may coincide with, or approximate to, any multiples of the proposed sampling interval. In such cases, it is strongly recommended that stratified random sampling within fixed time or mass intervals be carried out.

Jan 1, 1991

By R. E. Cook

"Mineral deposits require substantial amounts of energy to transport and be processed into useable form, and as such present a real processing challenge in that the deposits are never homogeneous and ore body compositional characteristics are all over the map! Extracting the desired mineral(s) from the deposit at sufficient profit margin, despite severe fluctuations in market price, requires process automation architecture capable of supporting an integrated enterprise solution. Such an architecture will encompasses the activities of individuals, process units, process areas, plant level activities, mine management and business planning and accounting systems. Key to the automation process is the aspect of value generation. This paper brings together the various requirements for the automation of a mining enterprise and presents the different aspects of how to obtain value across the entire mining operation.INTRODUCTIONMinerals’ processing sites are historically long lived, 20 year life of mine is not uncommon and 75 years is not unheard of. Considering that hardware technology advancements are introduced every six months, or less, it is prudent to select process automation systems that adhere to “open” industrial standards versus proprietary based systems. In the minerals processing industry, the key to survival is driving the cost of production per unit volume to the lowest possible level and provide enough profit to sustain operations. Control system architecture and Business information technology are rapidly becoming important tools in the quest for productivity. Getting key dynamic business performance information at the right time to the right person or process unit is crucial to successfully achieving corporate goals. The process automation architecture selected must therefore be able to integrate to the various networking enterprises and business systems.The mining industry is generally known as an “extractive” industry that is very physically-oriented with respect to operations and the activities in which workers engage. Large numbers of people performing manual tasks in difficult surroundings, produce very variable outputs. But, times are changing – and so are industry best practices. While the nature of work still consists of activities such as ore extraction, ore movement, ore concentration, refinement and logistics, automation innovations are starting to change the nature of many of the production steps. The industry has transitioned from requiring more physical activities by workers, to more information management, automated control and collaboration within the operation. Humans are good at situational intervention and non-linear reasoning and do best when empowered with an overall production perspective. Machines and automation are good at repetitive functions, steady state operation, and managing transitions. Thus, a combination of advanced technology solutions, reliable and useful information and full human contribution are necessary to mining operations for value generation."

Jan 1, 2015

By P. A. Delfosse

Numerous terms are used for rocks containing calcium carbonate so that confusion frequently occurs in the common language. Chalk and marble are two extremes among a wide variety of carbonate rocks including limestones, marls, travertine and other calcareous materials. We will deal mainly with the purest types of natural calcium carbonates which are widely used today in many industrial applications.

Jan 1, 1986

By Thomas S. Bubanovich

This paper will discuss the installation and operation of the Mundix Monitoring System at the Freeman United Coal Mining Company's Orient No. 4 Mine. Detailed explanations of the objectives set by Management, description of the mine, description of the system, installation procedures, and material used, operating procedures, maintenance procedures, and personnel requirements as well as experiences with carbon monoxide monitoring.

Jan 1, 1987

By John A. Herbst, Per-Olaf Samskog, Jan Bjorkman, Yi Chang Lo

The study described here is concerned with the development of a model for the simulation and optimization of a rod milllpebble mill circuit. A series of laboratory tests was conducted to investigate the effect of critical operating variables. The pebble mill model structure used was a population balance type which accounta for impact breakage and fines production from pebble wear. Model parameterization and verification were performed using data obtained in batch tests and in a plant test campaign. The model developed was found to provide accurate predictions of plant-scale grinding. The prediction errors are less than 21 for the product size and 31 for the mill power required to achieve that product with a mill volume scale-up of 14,000 to 1. These results indicate that accurate extrapolations from laboratory batch data to plant scale performance are poaaible using the population balance model and scale-up prediction procedures for pebble mill circuits as well as ball mills. Preliminary indications are that the new model developed here will provide vital input for pebble mill optimization and process control as well as pebble mill design.

Jan 1, 1990

By M. Yekich, W. R. Reed, G. Ross, M. Shahan

"Canopy air curtains on roof bolting machines have been proven to protect miners from respirable dust, preventing their overexposure to dust. Another desired application for canopy air curtains is in the compartments of shuttle cars. The challenges faced in developing the design of canopy air curtains for shuttle cars include mine ventilation rates in tandem with the shuttle car tram speeds. The resulting cab airspeeds may exceed 182 m/min (600 fpm), as found in the present study conducted in a central Appalachian underground coal mine by U.S. National Institute for Occupational Safety and Health (NIOSH) researchers. Prior research and laboratory testing had indicated that successfully protecting a miner in high air velocities is difficult, because the clean air from the canopy air curtain is unable to penetrate through the high-velocity mine air. In this study, the dust concentrations to which a shuttle car operator was exposed were measured, and air velocities experienced by the operator were measured as well using a recording vane anemometer. The results indicate that the highest exposure to respirable dust, 2.22 mg/m3, occurred when the shuttle car was loading at the continuous miner, where the average airspeed was 48 m/min (157 fpm). While tramming, the operator was exposed to 0.77 mg/m3 of respirable dust with an average airspeed of 62 m/min (203 fpm). This study indicates that a canopy air curtain system can be designed to greatly reduce an operator’s exposure to respirable dust by providing clean air to the operator, as the majority of the operator’s dust exposure occurs in air velocities slower than 61 m/min (200 fpm). IntroductionThe U.S. National Institute for Occupational Safety and Health (NIOSH) issued contract #200-2015-63485 to develop a canopy air curtain for coal mine shuttle cars with Marshall University and J.H. Fletcher & Co. (Salem, Begley and Ross, 2016). The proposed design maintains a design similar to that of a roof bolter canopy air curtain by providing filtered air through a blower over the operator. The plenum, which will provide uniform airflow over the operator, is anticipated to be built into the shuttle car canopy. One of the main interferences with a canopy air curtain is ventilation airflow perpendicular to the plenum airflow (Engel, Johnson and Raether, 1987). This ventilation airflow can shear the downward flow from the plenum, and this shear can reduce the effectiveness of the canopy air curtain by either disrupting the downward flow or allowing contaminated mine air into the canopy air curtain zone of protection."

Jan 11, 2018

By Mike Jahraus

The topic I would like to throw out for discussion this morning concerns the metallurgical solution management of operating a valley fill leach facility where ore depths approach 250 feet and deeper. We are currently beginning to experience solution transport times through our heaps on the order of 60 to 70 days as our heaps approach 250 feet. Incorporating a two-stage leach scenario, or solution enrichment, these times are nearly doubled. Concurrent with the increased solution transport times, the solution tenors being produced by our heaps are being diluted slightly as percolation occurs through the lower lifts. I feel the best way to handle these situations is to closely monitor solution application rates, and carefully manage ore stacking. Also, as heaps become deeper, metallurgical and hydrologic characteristics of the ore become inter-related, i.e. if channeling or preferential flow is taking place, lowering cross-sectional flow rates to older leach panels with help re­institute capillary flow while helping to prevent solution tenor dilution.

Jan 1, 1999

By Sangwhui Cho

In comminution processes including crushing, grinding and pulverizing, the efficiency of the comminution system is very low. Since the early 1980s, research has been conducted to increase the efficiency of pulverizing mills. Additionally, the application of microprocessors and Personal Computers to process control have come into general use. Given appropriate models of the process and control algorithms, these systems can economically control comminution processes. The ring-roller type mineral pulverizer is known as an energy saving mill. In this study, a control strategy to increase the efficiency of this type mill is explained.

Jan 1, 1992

By Ziyan Ouyang, Haotian Zheng, Spencer Quiel, Mike Mooney, Clay Naito

This paper summarizes the results of an experimental program conducted to characterize the moment-rotation behavior of skewed flat radial joints from large diameter (45 ft) tunnel lining. Both positive and negative joint moment-rotation behaviors were measured experimentally using two-segment joint combination assemblies. The results are compared to closed form methodologies used by designers, e.g., the Janssen method. The differences in observed and model behavior are discussed within the context of design practice.

Jun 23, 2024