Search Documents

By Franklin H. Sharp, R. Woods

The operation of the Magmont Concentrator located on the New Lead Belt of Southeast Missouri is described. Ore characteristics affecting lead-copper-zinc separation are enumerated, and the cur- rent methods of separation are detailed.

Jan 1, 1976

By Joe Komadina

DOUG HALBE: Our next topic is one that I would think everyone might want to contribute to. I'm sure everyone here has had some experience in this area. If you haven't, I'd suspect you've never really run a mill. This is what we call "Horrible Spill Areas We Had When We Started Up the Plant and How We Fixed Them." Our next speaker has had a really great operating career. He had many years with Newmont in the Carlin area, and now he's executive vice president and chief operating officer of Independence Mining Company: Jim Komadina. I don't have to be nice to the speakers anymore, do I? [laughter] You may wonder why we picked Jim Komadina to give this talk. I was involved many years ago in the start-up of Newmont7s Gold Quarry plant. Jim held quite a responsible position there. I'm not going to say anymore, but I have in the back of my mind this picture of the pump floor and a rowboat and a guy rowing around on the pump floor. [laughter] Jim, was that you? [laughter] JIM KOMADINA: Probably. I wasn't responsible for the design. [laughter] Actually it's amazing. I've seen a lot of these plants and actually had the opportunity to walk around them, so when I say this, "Horrible spills I have seen and done," it's because I've been responsible for more than my fair share of them. But having seen a lot of spills, I will present a little bit of wisdom about how to prevent them.

Jan 1, 1998

By R. R. Young

Prior to 1903, the world's supply of sulphur was primarily from surface deposits in Sicily. The discovery of the first salt dome sulphur deposit in 1867 and successful development of the Frasch process for recovering the sulphur resulted in a large part of this essential element being supplied from these mines since 1920. Although the basic process is the same today, engineering and technological developments have evolved to allow its application under many adverse conditions. These and other challenges for the industry in today's environment will be discussed in the paper.

Jan 1, 1979

By C. J. Johnson

As the U.S. coal industry moves into the next century, it is becoming more apparent that the effective application of new technology is the only way it can remain competitive in the energy marketplace. Examples of this emphasis are with us today in such diverse areas as face-ventilation and excavation-equipment applications. The focus of this new technology is directed toward improvements in health and safety, cost control, and productivity. Room-and-pillar mining accounts for approximately 80% of the nation's underground coal production; this percentage is not expected to decrease markedly in the near future. As such, this paper analyzes the impacts of the changing technological climate on future room-and-pillar operations by comparing a base-case section (current) to three scenarios incorporating new or emerging technology. A microcomputer-based comparative analysis will reflect the changes in section production and costs.

Jan 1, 1988

By E. G. Joe

Introduction Uranium mining has been actively carried on in Canada for over twenty-five years mainly in Ontario at Elliot Lake in Bancroft, and in Northern Saskatchewan at the operations of Eldorado Nuclear Ltd. During this period, approximately one hundred million tons of mill tailings have been created and lie mainly on the surface close to the mining and milling installations. If all of the present reserves of uranium ores in Canada are mined, a further eight hundred million tons of mine tailings could be created in Ontario, Saskatchewan, the Northwest Territories, Labrador and British Columbia. The present control of effluents from existing tailings is managed by the operating mines under the regulations of both federal and provincial control agencies. It is the long-term effect of these tailings on the environment that has not been clearly defined or measured. Several years ago, the Canada Centre for Mineral and Energy Technology of the Department of Energy, Mines and Resources, embarked upon a program of research directed at the long-term effects of uranium mine tailings. Much of the research to date has been on tailings in the Elliot Lake, Ontario area where some tailings piles have existed for over twenty years. The program consists of two projects, one to address the problem of existing tailings and the other to examine alternatives in the management of current and future tailings. TAILINGS CHARACTERISTICS Uranium tailings are generally the result of sulphuric acid leaching in which the uranium and alkaline minerals such as carbonates and chlorites are leached out. If the ore contains sulphides, these minerals potentially present an additional hazard of acid generation over time and could increase the mobility of heavy metals and some radionuclides such as thorium-230. Except for the extracted uranium, most of the radionuclides from the ore remain in the tailings pile. Uranium ores in Canada span a wide variety of mineralization and associated gangue composition. Uranium minerals include pitchblende, uraninite, uranothorite, brannerite and the phosphate uranium minerals autunite and saleeite. Gangue minerals vary from acid consuming carbonates, and chlorites to acid producing sulphides and inert silicates. With such a wide variety in ore composition, the characteristics of the resultant tailings in Canada are in many cases site specific and the solutions to the long-term effects of these tailings may also be site specific.

Jan 1, 1980

By W. J. Wuest, M. J. DeMarco

The US Bureau of Mines (USBM) recently developed a rock-mass classification system for evaluating the structural competency of bedded roof strata. The system is called the coal-mine roof rating (CMRR), When compiled with the companion Lotus 1-2-3 spreadsheet, CMRR data are a useful tool with applications to longwall gate-road pillar design, safety-hazard mapping and artificial roof-support analysis. This paper gives a review of some applications under actual conditions found in current US mining operations.

Jan 1, 1997

By William Lodding

Unlike most ore minerals, the raw materials for lightweight-aggregate, such as clays and shales are abundant everywhere. In view of this ample choice, what are the reasons for many plant failures attributed to the raw material? How can we arrive at a proper choice of the raw material, the proper processing method for the chosen material, predict its behaviour in a plant and the properties of the final product? Determine the uniformity of the raw material and possible harmful impurities? One basic choice is sintered versus kiln-fired aggregate. It will be based on market preferences and availability of the raw material. Almost in every case a good raw material for one process is poison for the other.

Jan 1, 1964

By Alessandro Navarra, Aldo Quelopana

For decades, open-pit mine planning algorithms have incorporated geological uncertainty and other elements or characteristics for increasingly realistic representations. Among these complexities is the detailing of downstream processes that occur inside processing plants. Previous studies have demonstrated that the strategic mine plan and mineral concentrator design are coupled, and should therefore be optimized simultaneously within the same quantitative framework. However, existing frameworks offer limited representation of operational modes. This work demonstrates an approach to resolving this gap, in an optimization based on a parallelized Variable Neighborhood Descent (VND). The resulting algorithm embeds mass-balancing linear programming (LP) using a DantzigWolfe decomposition. A case study of a Zn-Pb deposit is presented to show the performance reached.

Jun 25, 2023

By J. F. Colinet, W. R. Reed, J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. In general, all of the selected mines exercised good dust control practices by maintaining water sprays, scrubber airflows, proper curtain setback distances and providing sufficient airflow to the active faces. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 12.2 m (40 ft) of advance, because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation), as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011

By J. Scheepers, P. Smith, G. (Yunfei) Qiao

High pressure acid leach (HPAL) and pressure oxidation (POx) or pressure leaching extraction processes occur in autoclave vessels operating at elevated temperature and pressure, acidic conditions with abrasive mineral slurries. The harsh process conditions require specialized severe service metal seated ball valves to support operation of the vessels. Over several decades thermally sprayed titanium dioxide (TiO2) and chrome oxide (Cr2O3) coatings have been applied to extend the service life of the ball valves and other high wear critical components. Variability in the coating application quality control and severe process conditions can result in spalling, coating failure and premature failure of the component resulting is decreased autoclave circuit availability. In 2012 MOGAS, together with BRENCO, initiated research and development for ML-381, metallurgically bonded coating. This paper includes the historical development of severe service ball valve coatings, success of the trials and increasing industry adoption of the ML-381 coating for ball valves and other critical autoclave circuit components.

Mar 2, 2022

By D. Lynn, D. Arthur

Infrastructures continue to age and drinking water supplies are becoming scarce in the San Fernando Valley of Los Angeles, California. Frontier-Kemper Constructors, Inc. (FKCI) was engaged by the Los Angeles Department of Water and Power (LADWP) to complete the River Supply Conduit Improvement Upper Reach—Unit 7 Project (RSC7). Two tunnel sections were bored using a 2.64 meter diameter Microtunnel Boring Machine (MTBM) and a 4.12 meter diameter Earth Pressure Balance Tunnel Boring Machine (EPBTBM) to excavate approximately 3,733 meters (3.7 km) of tunnels through highly abrasive late-Pleistocene-age Quaternary alluvial deposits (Old Alluvium) and Holocene age Young Alluvium deposits above the water table. This paper discusses the challenges encountered managing the TBM’s equipment degradation, use of soil conditioners, cutterhead wear, torque and advance rates while maintaining the necessary face-pressures and parameters to limit over excavation and ground settlement.

Jun 13, 2021

By A. J. Erickson

In mid 1970, Park City Ventures, a Utah partnership of ASARCO and TAC, initiated a six phase exploration and development program in the Park City District, Utah. Geologic studies had delineated a number of exploration tar¬gets in several areas of the district. Discovery of ore in any of the target areas and continued favorable down dip development below then productive ore bodies would allow for reserve expansion and mill construction. The targets were: Mississippian Humbug Formation replacement mineralization below productive ore bodies on the east flank of the Park City Anticline; Humbug replacement mineralization in an unexplored fault block in the footwall of the Hawkeye structure on the east flank of the anticline; vein and replacement mineralization along the Silver Fissure; potentially higher grade Humbug replacement mineralization in a theorized structural block on the west flank of the anticline beneath the Ontario Vein; Permian Park City Formation replacement mineralization in the West End Shaft Area of the Silver King mine; vein mineralization along the Back Vein in the Judge Mine. Chilean Nationalization in 1971 resulted in a 30% budget cutback. The Judge and Silver King Projects were suspended. In spite of the cutback additional reserves were developed below the Humbug East Flank ore bodies; a major zone of ore grade mineralization was discovered along the Silver Fissure; five new ore bodies were found in the Humbug, and Doughnut Formations on the west flank of the anticline beneath the Ontario Vein. First concentrates were shipped from a new mill in May 1975.

Jan 1, 1976

By A. J. Basu

A prototype expert system for planning and designing underground coal mines has been developed in a doctoral study (Basu, 1991) at the University of Kentucky (U.K.). The objective of the study was to provide a design tool for configuring layout parameters, production systems, and for determining economic feasibility. Details of knowledge engineering and the prototype knowledge-based system for integrated and intelligent planning and design have been covered in the dissertation. The prototype demonstrates its robustness by allowing interaction among major design components, most notably among ventilation, ground control, and production planning. A plan for testing and evaluating the prototype, an important phase of software development, is presented here. Existing evaluation procedures for expert system prototypes are discussed and the evaluations for the underground coal mine design expert system prototype are included. The initial testing plan used senior-level mining engineering students to test the acceptance of the prototype. This test suggested the usefulness of such a system for training and instruction. This initial acceptance test was performed with the feasibility prototype. The other test objective, i.e., testing the model's accuracy, involved extensive participation of domain experts. For overall accuracy evaluation, an existing underground coal mine design was compared with the output from a design session using the expert system prototype. The testing procedure is not an isolated, independent development phase. Much of the accuracy evaluation is done at the time of knowledge base development. Therefore, the knowledgebase itself does not need a formal test phase. The major purpose of the field testing is to determine probable user acceptance. The acceptance test determines the completeness of the prototype and also will determine efficiency of user interfaces.

Jan 1, 1992

The first of this two part series takes a look at some of the history and types of flotation as well as agents and mechanisms involved in it. Part two, next month, will examine flotation processes as applied to various sulfide and nonsulfide mineral ores. Flotation-"froth" flotation-is a physicochemical method of concentrating finely ground ores. The process involves chemical treatment of an ore pulp to create conditions favorable for the attachment of predetermined mineral particles to air bubbles. The air bubbles carry the selected minerals to the surface of the pulp, there forming a stabilized froth that is skimmed off and from which the predetermined mineral particles are recovered. Other minerals remain submerged in the pulp.

Jan 3, 1982

By L. F. Moran

Rod Mill Grinding is an important and fundamental step of the concentrating process in Marcona Mining Company's plants at San Nicolas Bay, Peru. This Paper summarizes experience in regard to consumption and specifications of grinding rods based on twelve years operation of the grinding circuits. Marcona operates a Plant complex producing 10 million tons per year of beneficiated iron ore products including pellets, sinter feed concentrates, high grade concentrates as slurry and filter cake. Processing capacity is 15 million tons per crude ore per year of which 13 million are around in rod mills. A continuous testing program was carried out over the years. Initial studies of daily production operations gave indications of poor grinding rates in relation to mill size and power consumption, with a high rate of broken liners and rods. The broken nieces of rod were not automatically expelled and further interfered with grinding efficiency, while replacement of liners caused unwarranted do n tire. Objectives were to improve all phases of the Process by studying the effects of changes in rod diameter, length, alloy constituents, and volume and weight of rod charge.

Jan 1, 1975

By R. P. Plasket, G. M. Dunn

The cobalt plant was successfully commissioned in mid-1983. It is located within the company's nickel - copper re finery situated in Springs, South Africa. Plant design, which began in 1981, made provision for the corrosive process environment, stringent environmental standards, and the latest noise abatement requirements. In addition, the process flowsheet for the primary recovery of the cobalt byproduct and the purging of six impurity metals (nickel, iron, copper, manganese, lead, and arsenic) was designed with simplicity as a primary objective. High purity cobalt powder has been produced since commissioning.

Jan 1, 1987

By L. L. Anderson

Western bituminous coal can be processed to low sulfur liquid fuels by fast reactions. A process (LEFCO) under development at the University of Utah uses coal and catalyst under hydrogen pressure to convert 60 to 70 percent of the coal matter to fuel liquids and gases. Coals have been processed in small diameter (less than 1/2 inch) tubes and at reaction residence times of less than 10 seconds. Effects of process variables on the yield and quality of products have been studied. General features of the process and the properties and characteristics of the products produced are presented. Special features of the process that distinguish it from other liquefaction processes under development are also discussed.

Jan 1, 1975

By Thomas W. Camm

The U.S. Bureau of Mines has extensive experience estimating the cost of mining and mineral processing operations as an ongoing part of its information and analysis studies. With the increased interest in remediation of mine wastes, the USBM is developing a methodology to expand its cost estimating expertise to include costs of various remediation techniques applicable to mineral processing and mining wastes. By integrating waste remediation costs with existing USBM cost estimating systems for mine and mill operations, a comprehensive system for cost engineering studies will be developed.

Jan 1, 1995

By F. Figge, T. Hahn

In this article we present Sustainable Value, a valuation methodology to assess sustainable value creation of companies. Sustainable Development posits that decisions must not only take into account economic capital but also natural and social capital. Sustainable Value, the methodology presented in this paper, borrows the idea from financial economics that the return on capital has to cover the cost of the capital. Capital costs are determined as opportunity costs, i.e. the forgone return that would have been created by an alternative investment. By expanding the well established logic of the valuation of economic capital in financial markets to also cover natural and social capital we provide a methodology that allows an assessment of the most efficient allocation of economic, natural, and social capital for sustainable value creation in companies. We demonstrate the practicability of the methodology by the valuation of the sustainability performance of British Petroleum (BP).

Jan 1, 2005

By J. P. Rider

The number of extended cut mining systems has increased significantly in coal mines over the last decade, and there is a constant push to extend the face ventilation systems to even greater setback distances. The need to maintain airflow at setback distances of12.2 m (40 ft) and beyond requires that methods for delivering intake air to the face be improved, or alternative ventilation techniques be implemented. The emphasis of this research effort was to examine various techniques to improve the distribution of available air at the mining face in order to reduce face methane levels. A study was conducted comparing the performance of a jet fan, used in conjunction with a machine mounted scrubber, with blowing curtain ventilation in a 27.5 m (90 ft) heading. In addition, a second study was performed on blowing curtain systems examining how scrubber flow, intake air velocity, and curtain setback influence face methane concentrations. Results showed that when the heading advances to a depth of 27.5 m (90 ft) blowing curtain systems were more efficient at diluting face methane levels when compared to a jet fan. Also, increases in scrubber flows and curtain velocity resulted in lower face methane concentrations for blowing curtain systems at 9.2 and 15.2 m (30 and 50 ft) setbacks.

Jan 1, 1997