Search Documents

By K. V. Raj, R. Jacksha

Conveyor systems persist in being a source of injuries and fatalities in the mining industry. To reduce these incidents, better methods are needed to enhance the monitoring of probable hazards and improve situational awareness during the normal operation and maintenance of conveyor systems. To address these issues, researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) continue to investigate emerging technologies that show the potential to improve miner safety around conveyors. This paper presents a feasibility assessment by NIOSH researchers of a fully integrated, commercially available wireless Internet of Things (IoT) system to improve situational awareness around conveyor systems.

Flooded-bed scrubbers on continuous miners have been shown to be an effective respirable dust control technology, traditionally used during the extraction of extended cuts of up to 12.2 m (40 ft). To effectively use scrubbers in faces that employ exhaust ventilation, the return ventilation curtain or tubing should be located outby the scrubber discharge on the continuous miner, which results in a setback distance from the face of approximately 12.2 m (40 ft). The goal of this research was to compare respirable dust levels generated in 6.1 m (20 ft) cuts when using extended curtain setbacks with a scrubber operating to dust levels in 6.1 m (20 ft) cuts when using traditional exhaust face ventilation without a scrubber operating. Dust surveys were completed at three mines with area and personal sampling conducted to quantify respirable dust concentrations on a cut-by-cut basis. Sampling results did not show a statistically significant difference in respirable dust at the continuous miner or shuttle car locations with and without the scrubber operating. However, with the scrubber operating, respirable dust concentrations in the return airstream downwind of the miner showed reductions of 91%, 86%, and 40% at Mines A, B, and C, respectively. The reductions at Mines A and B were statistically significant. Likewise, reductions in respirable quartz dust levels in the miner return were observed at all three mines, with statistically significant reductions of over 80% observed at Mines A and B. Consequently, operation of the flooded-bed scrubber did not impact respirable dust levels in the face area but did significantly reduce respirable and quartz dust levels downwind of the continuous miner. These results were obtained with the mines operating at or above the minimum operating levels specified in their ventilation plans.

Feb 23, 2014

By Jin Kim, Jerry C. Tien

Water is still the most economical and popular means of controlling dust underground. It is a process that captures dust by bringing water droplets into intimate contact with coal particles. Wetting agents, also known as surfactants, can be added to greatly facilitate such a process since they tend to reduce the interfacial tension between the coal particles (usually hydrophobic) and the liquid. The surfactants used in the study were first chosen on the basis of their HLB (Hydrophile-Lipophile Balance) value, and later tested in order to select the right type and amount of surfactants to give the best performance. Both static and dynamic tests were later conducted using different types of surfactants to examine their respective wetting effectiveness on coal particles. Experimental results show close correlation with the theoretically calculated collection efficiency that is based on a horizontal tunnel and a solid-cone water spray.

Jan 1, 1993

By Yuting Xue, Gamal Rashed, Zoheir Khademian, Morgan Sears

Mining has been recognized among the most hazardous industries in the United States, despite the significant reduction in injury and fatality rates over the past century. This study focuses on the ground-fall incidents classified in the Mine Safety and Health Administration (MSHA) database as “fall of roof, back, or brow from in-place” and “fall of face, rib, pillar, side, or highwall.” The main objective of this study is to conduct a comprehensive statistical analysis of the reported ground-fall incidents from 2010 through 2019 including both coal and metal/non-metal mines. Since most of the ground-fall injuries and fatalities occurred in underground coal mines and were attributed to falls of roof and rib, an additional analysis was directed to evaluate roof- and rib-fall incident trends in underground coal mines associated with the mining method, coal-seam thickness, mine size, and the seasonal effects.

By G. Robert Moorehead, Peter T. Luckie, Harold L. Lovell, David J. Akers, James K. Kindig

Jigging is a process of particle stratification in which the particle re- arrangement results from an alternate expansion and compaction of a bed of particles by pulsating fluid flow. The vertical direction of fluid flow is reversed periodically. The rearrangement results in layers of particles that are arranged by increasing density from top to bottom of the bed. This response, developed from the many and continuously varying forces acting upon the particles, permits a solid-solid separation more related to particle density and less to particle size than any other "hydraulic-type" process. The stratification is usually carried out in a rectangular, open-top container called a jig, in which the mass of particles (termed a "bed") is supported on a perforated base through which the water flows in alternating directions. The coal particles, in addition to the vertically expanded and compacted bed motion, move continuously, horizontally across the supporting screen. Following the particle stratification, the particle bed is physically "cut" at a desired horizontal particle density plane to separate the desired clean coal product from the more dense refuse. The jig system includes means for continuously introducing the raw coal and for moving the water through the coal bed in a controllable manner, as well as for separating and removing the stratified particles from the system as two or more product streams. In coal preparation, this highly versatile unit operation is applied preferably to a wide size range of particles with top sizes up to 8 in. (20 cm) rather than to a closely sized fraction. In gravity ranges, the process has been applied to gold particles with a density of 19.3 and to coal particles having densities less than 1.30. Single jig washers have capacities from 5 (4.6) to greater than 700 tph (637 t/h) of feed coal. The separation results attainable by jigging have favored this unit operation as optimum for creating a clean coal product as required by steam coal specifications. Al- though the jig is used in preparing coals which are difficult to separate, its limitations to achieve both quality products and high recovery are being recognized in comparison with heavy media-based processes which make sharper separations from feeds having high "near-gravity" contents. The accu- racy of the densimetric stratification in the upper portions of the jig bed are less precise. It follows that coals with more than 10% near-gravity material

Jan 1, 1991

By John D. Batty

With the emergence ofbiooxidation as a viable process for the pre treatment of refractory gold ores, so have the number of publica­tions on this topic increased dramatically. To a novice in the field of biooxidation, the infonnation presented is often confusing and sometimes even incorrect. Infonnation has also been published that is misleading in that it highlights a particular feature of a process that is either totally irrelevant or of no consequence to the ultimate goal viz. achieving the maximum economical gold recovery. To assist a potential user of biooxidation in evaluating the available published infonnation some guidelines or considera­tions for some of the more important aspects are given, as well as some extracts from publications that demonstrate the manner in which information has been presented.

Jan 1, 1996

By MYRIAM FRANCOEUR, JOHN R.R. BOWLING, ADAM MCFADDEN

As duct-fan systems push the envelope of power, length and cost, their design calls for a more comprehensive technoeconomic analysis to ensure they deliver the expected results without failure and cost overrun. This work explores the numerous factors to include in the design of an extensive (semi-)rigid duct-fan system. Besides delivering a given airflow, the system must satisfy component limitations and power constraints during its lifetime. We evaluate the assumptions underlying the positioning of in-line booster fans in a long gapless duct-fan system and propose a strategy for specifying the location and blade pitch of successive booster fans to prevent system failure due to a partial vacuum.

Oct 1, 2022

By L. Tondo, W. Lim

The high pressure grinding rolls (HPGR) is a relatively new technology which offers the potential benefits in energy savings, circuit simplicity and improved product characteristics in minerals processing applications. Over 300 machines are now operating world-wide, but most of these are used for grinding cement clinker, and relatively few are used in conventional mineral processing. One of the rea- sons for its current limited use in the minerals processing industry is that design, scale-up and flowsheet assessment procedures are seen to be relatively immature and untested. This has reduced confidence in the potential application of the technology. To help rectify this situation an industry funded research project was undertaken, one of whose aims was to develop and prove a mathematical model of the HPGR and a scale-up procedure. Data were collected from tests using laboratory, pilot and in one case a full scale unit (2.2m diameter). A range of feed types were tested including quartz, limestone, kimberlite, bauxite, iron ore and gold ore. These data were then used to develop models of the size reduction performance, power draw, throughput and operating gap for a wide range of pressures, feed sizes, and roll speeds. This paper describes the models that have been initially developed and illustrates their accuracy using some of these data.

Jan 1, 1998

By Eugene F. Casey

An immersed tube tunnel is one which is composed of elements that are prefabricated in a dry dock or on shipways, usually away from the actual tunnel site, floated into position and then lowered into a preexcavated and graded trench below a body of water. The elements or segments are then connected to each other under water, and the entire immersed tube tunnel covered with a protective blanket. Because water is essential, this method of construction offers advantages in a relatively limited field. By the very nature of the method, lowering elements to the bottom of an underwater trench, immersed tube tunnels are primarily used for crossing bodies of water, such as rivers, bays, straits, canals, etc. Although this method of construction was first used for a subaqueous railway crossing under the Detroit River in 1906-1910 and again in 1912-1915, for a four track subway tunnel under the Harlem River in New York, the reason immersed tube tunnels construction has not been used more extensively is simply a matter of economics. Bridges, compressed air tunnels and similar structures could be constructed at a lower cost.

Jan 1, 1970

By Stefan Gerl, Werner Stahl

Steam pressure filtration combines mechanical and thermal processes in one filtration device. Steam condensation at the cold layers of the filter cake, build a condensation front, which even removes the capillary water from the porous filter cake. Depending on the choice of parameters it is possible to achieve a very low residual moisture content. The influence of the parameters on the dewatering results was systematically examined on a bench-scale apparatus. This paper explains the physical fundamentals, the influence of the cake dewatering parameters, and one possible method of applying the process to a disk filter device as well.

Jan 1, 1995

By Timms. Greg P., John W. Bennett

A field-based method for measuring the diffusive oxygen flux through covers placed on sulfidic waste rock dumps has been developed and applied at a number of mine sites. The technique provides a means of quantifying oxidation rates in dumps and can thus be used to assess the effectiveness of cover systems. Two instruments can be used. The first is portable and easy to set up, enabling a picture to be built up of the overall diffusive flux into a dump by making measurements at a sufficient number of locations. The second is installed beneath a cover and is preferred in situations where oxygen is consumed in the cover since it provides a direct measurement of the oxygen flux into the underlying waste rock.

Jan 1, 2000

By Peter Sullivan, Johan van Heerden

Increased use of continuous miners and roadheaders in the underground coal mining industry in South Africa has led to improved productivity and efficiency of operations. Of major concern, however, is the increased amount of airborne dust generated during mining. Dust is a health hazard in terms of respiratory diseases, can impede productivity and is the major contributor to the potential of underground explosions. The concern of the South African coal mining industry with regard to the underground dust problem has led to the establishment of a Dust Control Section in the Coal Mining Division of COMRO. In the field of dust suppression system evaluation and design, collaborative work has been undertaken by COMRO and FLOSEP. This paper gives a review of the application of Computational Fluid Dynamics (CFD) in evaluating and improving environmental conditions in continuous miner and roadheader sections. A brief history of the development of the CFD model as well as a discussion of a typical application is included.

Jan 1, 1993

By B. Cavender

The operating lifetime, or production rate, selected for a mining project is among the most important factors influencing the project's design and ultimate economic success. Incorrectly-determined lifetimes can lead to the erroneous rejection of projects as uneconomic as well as the suboptimal exploitation of producing properties. This paper examines the optimal lifetime calculation using traditional discounted cash flow and recently-proposed option pricing techniques. Using each method, the production rate is determined as that rate at which the project's net present value is maximized.

Jan 1, 1993

By R. P. Killmeyer, R. E. Hucko, P. S. Jacobsen

Cleaning of three coals from the eastern US was tested by five selective agglomeration processes and one selective flocculation process. The coals and processes are described, and the results are reported and compared. Two of the processes, which ground the coal to the finest volume mean diameter, met the stringent test program quality specifications.

Jan 1, 1991

By E. J. Harvey

The Ozarks has been called "a diamond in the rough". In this region streams have steep gradients, sparkling clear flows of cold water fed by many springs, and a wildness that is almost unique in the central part of the United States today. The Current River and its tributary, Jacks Fork, have been set aside for preservation by the National Park Service as a "Wild River" in the first park of its kind in the country. It is called the Ozark National Scenic Riverway. Similarly, responsibility for the preservation of the Eleven Point River has been assigned to the U. S. Forest Service. Protection of other streams in the Ozarks has been considered by State agencies. The hydrologic system of the Ozarks is a complex network of gaining and losing streams, caves, conduits, and large springs. Increased sewage loads derived from the growing towns and expanding tourist trade are a potential hazard; effluents may flow underground for long distances, polluting springs and wells. To add another dimension to the hydrologic picture a new lead industry is also flourishing in the Ozarks. Although the history of lead mining in the area goes back to 1701 (U. S. G. S., p. 43), the area has not seen a revitalization like the one that has been developing in the last 10 years; and the economic growth promises to continue indefinitely. Although this brings capital expenditures and wages into the area, it also brings potential hydrologic problems. Chemicals, wastes and other substances either stored on the surface or transported across it are subject to accidental spillage. In an area where these substances remain on the surface their effects are subject to surveillance. In the Ozarks, however, this may not be possible.

Jan 1, 1970

By Dennis E. Peterson

Land subsidence had been observed in recent years throughout the Southwest. Particular examples of this phenomenon that have gained wide publicity axe in the Long Beach and Central Valley areas of California and, the Houston area of Texas. Less well known is the fact that the land surface Is subsiding in many parts of Arizona, including the Phoenix area. The causes of this problem vary from place to place, as do also the rates of subsidence. In Houston it has been related to pumping water from artesian aquifers; in Long Beach to the development of oil fields; and in the Central Valley to both the lowering of artesian pressures in deep aquifers and the wetting of poorly consolidated surficial deposits. The mechanism by which subsidence occurs in southern Arizona, even though it can be correlated with the continued lowering of ground water levels, is not as apparent as in these other cases. It is the purpose of this paper to examine both the causes and affects of land subsidence in southern and central Arizona.

Jan 1, 1965

By P. C. van Aswegen

The Bacterial Oxidation (BIOX®) process for the pre-treatment of refractory ores for gold recovery developed by Genmin, the mining division of Gencor, has been operating successfully at the Fairview mine since October 1986. The continuous operation of a pilot plant at Genmin Process Research has resulted in further process developments to improve plant operating efficiencies. These new developments which include a higher solids content of the pulp feed to BIOX®, lower retention times, higher operating temperatures, lower power utilization for oxygen dispersion .and reduced nutrient addition have all been successfully implemented on the Fairview plant.lt has furthermore been confirmed that the arsenic precipitate formed in the neutralization of effluent solutions complies to the United States of America EPA standards. Continuous cyanidation pilot plant work conducted on BIOX® product has indicated that cyanide consumption can be drastically decreased if a continuous flowsheet is implemented in preference to a batch leaching system.

Jan 1, 1991

By W. Petruk, D. B. Sikka

Lithium-bearing lepidolites from three deposits in the province of Goias, Brazil, were investigated to determine whether there is a correlution between the lithium content of the mineral and the color of lepidolite and associated tourmaline. Such a correlation can be a useful guide to field geologists for outlining high-grade lithium ore zones. It was found that mauve-pink lepidolite associated with pink tour-maline, and brownish lepidolite associated with black tourmaline have high lithium contents, but that the color of lepidolite is not due to lithium. The pink color of lepidolite and tourmaline is likely due to Mn3+, and the brownish tint of lepidolite and black color of tourmaline to Fe3+. Lepidolites appear to be lithium- rich when the lepidolite and associated tourmaline contain relatively high amounts of Mn3+ and/or Fe3+.

Jan 1, 1988

By Claus Becker

Waterbearing, cohesive or non-cohesive grounds with glacial stone deposits are found very often in Europe. The problem consists of destroying the boulders and supporting the face simultaneously. At the example Grauholztunnel Bern ( outer diameter 11,60 m ) the theoretical attempt of solutions for the big machines is described: destroying of the boulders with roller discs, hydraulical support of the front. The problem of coming out of stones of a certain size from the surrounding matrix will be discussed. Further diminishing to the size that can be handled by pumps is executed by a crusher, situated in the center of the machine. At the same example the theoretical attempt for headings in cohesive soil with stone deposits are shown. Surface structure of the cutting wheel and working chamber as well as controllable current movements are the solution here. The danger of clogging discs and stone crusher has to be encountered by right positioning of the tools and jetting nozzles. At the example Sewer MoosstraBe Salzburg the same problems are discussed for the Mikro-Tunnels. The pipe-jacked sewer lines have outer diameters from 485 and 805 mm. With this method, the stones have to be holed through. The wear of the cutting tools determines the [ ]

Jan 1, 1989

By Matthew Deutsch

A common casualty of modern openpit mine optimization is the assurance that the resulting design is actually achievable. Optimized mine plans that consider value and a bare minimum of precedence constraints do not, in general, translate into practical, operational mine designs that can be used in the field. Ultimate pits may come to a sharp point at the bottom. Schedules may require taking small parcels of material from many disparate areas of the pit in a single period, and grade control polygons may be ragged, narrow and not minable with realistic equipment. In this paper, these three fundamental openpit mine optimization problems are addressed by encoding them as maximum satisfiability problems. Maximum satisfiability provides a useful framework for problems that are nonlinear and may guarantee the optimality that metaheuristics cannot.